Century Century AC 120 Mode d'emploi
- Catégorie
- Système de soudage
- Taper
- Mode d'emploi
Ce manuel convient également à
CENTURY AC 120
OPERATOR’S MANUAL
IM10067
May, 2010
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ-
ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT. And,
most importantly, think before
you act and be careful.
Copyright © Lincoln Global Inc.
• Century
®
Equipment
2345 Murphy Blvd. Gainesville, GA 30504 TEL: 866-236-0044
Web Site: www.centuryequipment.net
®
11728 K2964-1
THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELEC TRIC.
PLEASE EXAMINE CARTON AND EQUIPMENT FOR
DAMAGE IMMEDIATELY
When this equipment is shipped, title passes to the purchaser
upon receipt by the carrier. Consequently, claims for material
damaged in shipment must be made by the purchaser against the
transportation company at the time the shipment is received.
SAFETY DEPENDS ON YOU
Lincoln arc welding and cutting equipment is designed and built
with safety in mind. However, your overall safety can be increased
by proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,
think before you act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed
to avoid minor personal injury or damage to this equipment.
KEEP YOUR HEAD OUT OF THE FUMES.
DON’T get too close to the arc.
Use corrective lenses if necessary
to stay a reasonable distance
away from the arc.
READ and obey the Safety Data
Sheet (SDS) and the warning label
that appears on all containers of
welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to
keep the fumes and gases from
your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away
from your face.
If you de velop unusual symptoms, see your supervisor.
Perhaps the welding atmosphere and ventilation system
should be checked.
WEAR CORRECT EYE, EAR &
BODY PROTECTION
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare
with protective screens or barriers.
IN SOME AREAS, protection from noise may be appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area
AT ALL TIMES.
SPECIAL SITUATIONS
DO NOT WELD OR CUT containers or materials which previously
had been in contact with hazardous substances unless they are
properly cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release
highly toxic fumes or gases.
Additional precautionary measures
PROTECT compressed gas cylinders from excessive heat,
mechanical shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an
electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR
IMMEDIATE USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
Safety 01 of 04 - 5/16/2018
SECTION A:
WARNINGS
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Breathing diesel engine exhaust
exposes you to chemicals known to the State
of California to cause cancer and birth defects,
or other reproductive harm.
• Always start and operate the engine in a
well-ventilated area.
• If in an exposed area, vent the exhaust to the outside.
• Do not modify or tamper with the exhaust system.
• Do not idle the engine except as necessary.
For more information go to
www.P65 warnings.ca.gov/diesel
WARNING: This product, when used for welding or
cutting, produces fumes or gases which contain
chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California
Health & Safety Code § 25249.5 et seq.)
WARNING: Cancer and Reproductive Harm
www.P65warnings.ca.gov
ARC WELDING CAN BE HAZARDOUS. PROTECT
YOURSELF AND OTHERS FROM POSSIBLE SERIOUS
INJURY OR DEATH. KEEP CHILDREN AWAY.
PACEMAKER WEARERS SHOULD CONSULT WITH
THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For
additional safety information, it is strongly recommended
that you purchase a copy of “Safety in Welding & Cutting -
ANSI Standard Z49.1” from the American Welding Society,
P.O. Box 351040, Miami, Florida 33135 or CSA Standard
W117.2-1974. A Free copy of “Arc Welding Safety” booklet
E205 is available from the Lincoln Electric Company,
22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE POWERED
EQUIPMENT.
1.a. Turn the engine off before troubleshooting
and maintenance work unless the
maintenance work requires it to be running.
1.b. Operate engines in open, well-ventilated areas or vent the engine
exhaust fumes outdoors.
1.c. Do not add the fuel near an open flame welding
arc or when the engine is running. Stop the
engine and allow it to cool before refueling to
prevent spilled fuel from vaporizing on contact
with hot engine parts and igniting. Do not spill fuel when filling
tank. If fuel is spilled, wipe it up and do not start engine until
fumes have been eliminated.
1.d. Keep all equipment safety guards, covers
and devices in position and in good repair.
Keep hands, hair, clothing and tools away
from V-belts, gears, fans and all other
moving parts when starting, operating or
repairing equipment.
1.e. In some cases it may be necessary to remove safety guards to
perform required maintenance. Remove guards only when
necessary and replace them when the maintenance requiring
their removal is complete. Always use the greatest care when
working near moving parts.
1.f. Do not put your hands near the engine fan. Do not attempt to
override the governor or idler by pushing on the throttle control
rods while the engine is running.
1.g. To prevent accidentally starting gasoline engines while turning
the engine or welding generator during maintenance work,
disconnect the spark plug wires, distributor cap or magneto wire
as appropriate.
1.h. To avoid scalding, do not remove the radiator
pressure cap when the engine is
hot.
ELECTRIC AND
MAGNETIC FIELDS MAY
BE DANGEROUS
2.a. Electric current flowing through any conductor
causes localized Electric and Magnetic Fields (EMF).
Welding current creates EMF fields around welding cables
and welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health effects
which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and work
cables. If the electrode cable is on your right side, the
work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as pos-
sible to the area being welded.
2.d.5. Do not work next to welding power source.
SAFETY
Safety 02 of 04 - 5/16/2018
ELECTRIC SHOCK
CAN KILL.
3.a. The electrode and work (or ground) circuits are
electrically “hot” when the welder is on. Do
not touch these “hot” parts with your bare skin or wet clothing.
Wear dry, hole-free gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full area
of physical contact with work and ground.
In addition to the normal safety precautions, if
welding must be performed under electrically
hazardous conditions (in damp locations or while
wearing wet clothing; on metal structures such as
floors, gratings or scaffolds; when in cramped
positions such as sitting, kneeling or lying, if there
is a high risk of unavoidable or accidental contact
with the workpiece or ground) use the following
equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic welding
gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection should
be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical (earth)
ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of electrode
holders connected to two welders because voltage
between the
two can be the total of the open circuit voltage of both
welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see It ems 6.c. and 8.
ARC RAYS CAN BURN.
4.a. Use a shield with the proper filter and cover plates to protect your
eyes from sparks and the rays of the arc when welding or
observing open arc welding. Headshield and filter lens should
conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant material
to protect your skin and that of your helpers from the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES
CAN BE DANGEROUS.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases. When welding, keep your head out of the fume.
Use enough ventilation and/or exhaust at the arc to keep fumes
and gases away from the breathing zone. When welding
hardfacing (see instructions on container or SDS)
or on lead or cadmium plated steel and other
metals or coatings which produce highly toxic
fumes, keep exposure as low as possible and
within applicable OSHA PEL and ACGIH TLV limits
using local exhaust or mechanical ventilation
unless exposure assessments indicate otherwise.
In confined spaces or in some circumstances,
outdoors, a respirator may also be required.
Additional precautions are also required when
welding
on galvanized steel.
5. b. The operation of welding fume control equipment is affected by
various factors including proper use and positioning of the
equipment, maintenance of the equipment and the specific
welding procedure and application involved. Worker exposure
level should be checked upon installation and periodically
thereafter to be certain it is within applicable OSHA PEL and
ACGIH TLV limits.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations. The
heat and rays of the arc can react with solvent vapors to form
phosgene, a highly toxic gas, and other irritating products.
5.d. Shielding gases used for arc welding can displace air and
cause
injury or death. Always use enough ventilation, especially in
confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
Safety Data Sheet (SDS) and follow your employer’s safety
practices. SDS forms are available from your welding
distributor or from the manufacturer.
5.f. Also see item 1.b.
SAFETY
Safety 03 of 04 - 5/16/2018
WELDING AND CUTTING
SPARKS CAN CAUSE
FIRE OR EXPLOSION.
6.a. Remove fire hazards from the welding area. If
this is not possible, cover them to prevent the welding sparks
from starting a fire. Remember that welding sparks and hot
materials from welding can easily go through small cracks and
openings to adjacent areas. Avoid welding near hydraulic lines.
Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site, special
precautions should be used to prevent hazardous situations.
Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)
and the operating information for the equipment being used.
6.c. When not welding, make certain no part of the electrode circuit is
touching the work or ground. Accidental contact can cause
overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances inside.
They can cause an explosion even though they have been
“cleaned”. For information, purchase “Recommended Safe
Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous Substances”,
AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil free
protective garments such as leather gloves, heavy shirt, cuffless
trousers, high shoes and a cap over your hair. Wear ear plugs
when welding out of position or in confined places. Always wear
safety glasses with side shields when in a welding area.
6.g. Connect the work cable to the work as close to the welding area
as practical. Work cables connected to the building framework or
other locations away from the welding area increase the
possibility of the welding current passing through lifting chains,
crane cables or other alternate circuits. This can create fire
hazards or overheat lifting chains or cables until they fail.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “Standard for Fire Prevention During
Welding, Cutting and Other Hot Work”, available from NFPA, 1
Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.
6.j. Do not use a welding power source for pipe thawing.
CYLINDER MAY EXPLODE IF
DAMAGED.
7.a. Use only compressed gas cylinders containing
the correct shielding gas for the process used
and properly operating regulators designed for
the gas and pressure used. All hoses, fittings,
etc. should be suitable for the application and
maintained in good condition.
7.b. Always keep cylinders in an upright position securely chained to
an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected
to physical damage.
• A safe distance from arc welding or cutting operations
and any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand tight
except when the cylinder is in use or connected for use.
7.g. Read and follow the instructions on compressed gas cylinders,
associated equipment, and CGA publication P-l, “Precautions for
Safe Handling of Compressed Gases in Cylinders,” available from
the Compressed Gas Association, 14501 George Carter Way
Chantilly, VA 20151.
FOR ELECTRICALLY
POWERED EQUIPMENT.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National Electrical
Code, all local codes and the manufacturer’s recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Refer to
http://www.lincolnelectric.com/safety
for additional safety information.
SAFETY
Safety 04 of 04 - 5/16/2018
PRÉCAUTIONS DE SÛRETÉ
Pour
votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soud
e pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
iv
SAFETY
iv
vi
v
i
TABLE OF CONTENTS
Page
I
nstallation .......................................................................................................Section A
Safety ........................................................................................................................A-1
G
eneral Description...............................................................................................A-1
Technical Specifications ........................................................................................A-2
I
dentify and Locate Components, Input Connections............................................A-2
________________________________________________________________________
Operation .........................................................................................................Section B
Thermal Protection ................................................................................................B-1
Making A Weld.......................................................................................................B-1
Electrode Selection................................................................................................B-1
Learning to Weld.....................................................................................B-1 Thru B-4
________________________________________________________________________
Troubleshooting...........................................................................................Section C-1
________________________________________________________________________
Wiring Diagram ............................................................................................Section D-1
________________________________________________________________________
A
-1
INSTALLATION
CENTURY® AC 120
A
-1
SAFETY
R
ead the entire manual before installing and oper-
ating the AC 120.
ELECTRIC SHOCK can kill.
•
Only qualified personnel should installa-
tion or operate this equipment.
• Machine must be plugged into a receptacle
which is grounded per any national, local or
other applicable electrical codes.
• The AC 120 power switch is to be in the OFF
(“O”) position when connecting power cord to
input power.
• Do not touch electrically live parts or electrode
with skin or wet clothing. Insulate yourself from
work and ground.
• Always wear dry insulating gloves.
------------------------------------------------------------------------
FUMES AND GASES can be dangerous.
• Keep your head out of fumes.
• Use ventilation or exhaust to remove
fumes from breathing zone.
------------------------------------------------------------------------
WELDING SPARKS can cause fire or
explosion.
• Keep flammable material away.
• Do not weld on closed containers.
------------------------------------------------------------------------
ARC RAYS can burn eyes and skin.
• Wear eye, ear and body protection.
------------------------------------------------------------------------
GENERAL DESCRIPTION
T
he AC 120 is composed of a single phase trans-
former and is suitable for welding in alternate current
using stick electrodes (type 6013) with diameters from
1/16 to 5/64 in. The AC 120 is rated for a 20% duty
cycle at a rated output of 55 amps. A 55A output can
be drawn for 2 minutes out of each 10 minute period
w
ithout overheating.
SELECT SUITABLE LOCATION
This machine can operate in harsh environments.
However, it is important that simple preventative mea-
sures are followed to assure long life and reliable
operation:
• This machine must be located where there is free
circulation of clean air without restrictions for air
movement to and from the air vents. Do not cover
the machine with paper, cloth or rags when
switched on.
• Dirt and dust that can be drawn into the machine
should be kept to a minimum.
• Keep machine dry and do not place it on wet ground
or in puddles. Do not use in wet or damp locations.
Store indoors.
• Do not mount over combustible surfaces.
------------------------------------------------------------------------
WARNING
WARNING
A
-2
INSTALLATION
TECHNICAL SPECIFICATIONS
CENTURY® AC 120
A
-2
Breaker/Fuse Size Input Amps Power Cord
20 Amp 15 - 20 15 Amp, 125V
Three Prong Plug
(NEMA Type 5-15P)
Extension Cord
Up to 25 Ft. (7.6 m): Three Conductor #12 AWG
(3.3 mm
2
) or Larger
1/16” or 5/64” Fleetweld 37 (E6013)
INPUT – SINGLE PHASE ONLY
RATED OUTPUT
OUTPUT RANGE
Height Width Depth Weight
11.00 in. 7.00 in. 11.00 in. 24.5 Ibs.
280 mm 178 mm 280 mm 11 kg.
PHYSICAL DIMENSIONS
RECOMMENDED ELECTRODE & MATERIAL THICKNESS
Voltage/Frequency Input Current
120V/60Hz 15 Amps @ Rated Output
Welding Current Range
AC Output: 50-90 amps
Maximum Open Circuit Voltage
37
Duty Cycle Amps Volts
20% 55 27
RECOMMENDED INPUT FUSE SIZES AND
EXTENSION CORDS
A
-3
INSTALLATION
CENTURY® AC 120
A
-3
IDENTIFY AND LOCATE COMPONENTS
(
See Figure A.1)
If you have not already done so, unpack the AC 120
from its carton and remove all packing material
around the unit.
1
) INPUT CORD CONNECTION
This machine is intended to operate off a standard
household type receptacle (20A, 120V, 60Hz, sin-
gle phase, grounded). Refer to the Technical
Specifications at the beginning of this manual. If
connected to a circuit protected by fuses, use time
delay fuses marked "D".
2) WORK CLAMP
The work clamp and cable is attached to the
welder at the factory. The work clamp must be
directly connected to the workpiece or the work
bench. Make sure the contact to the workpiece is
adequate by avoiding painted or nonmetallic sur-
faces.
3) ELECTRODE HOLDER
The Electrode holder and cable is attached to the
welder at the factory. It has special contact jaws to
grasp the bare part of the welding electrode.
4) INSTRUCTION MANUAL
5) POWER SWITCH
INPUT CONNECTIONS
CODE REQUIREMENTS FOR INPUT
CONNECTIONS
• This welding machine must be connected to a
power supply in accordance with applicable elec-
t
rical codes.
• If there is any question about the installation
meeting applicable electrical code requirements,
consult a qualified electrician.
------------------------------------------------------------------------
Do not connect the AC 120 to an input power sup-
ply with a rated voltage that is greater than 125
volts.
Do not remove the power cord ground prong.
------------------------------------------------------------------------
WARNING
FIGURE A.1
1
2
3
5
4
CENTURY AC 120
1
2
3
5
4
CENTURY AC 120
B
-1
OPERATION
B
-1
THERMAL PROTECTION
I
f the duty cycle is exceeded, a thermal protector will
shut off the output until the machine cools to a reason-
able operating temperature. The Power Switch will
Illuminate if this condition occurs, which is an auto-
m
atic function of the AC 120 and does not require
user intervention. Output will resume once the
m
achine cools.
MAKING A WELD
(See Figure B.1)
Insert the bare part of the electrode into the electrode
holder jaws and connect the work clamp to the weld-
ing piece. Make sure to have good electrical contact.
Turn the AC 120 on. Lower Helmet or while holding
shield in front of face strike the electrode work point
on the workpiece as if striking a match. Do not hit the
electrode on the workpiece, which will damage the
stick electrode and make striking an arc difficult.
Immediately after striking the arc try to maintain a dis-
tance from the workpiece that is equivalent to the
diameter of the electrode used. Maintain this distance
continually during the weld.
Refer to the "Learning to Weld" section in this manual
for more information on:
• How to correctly strike an arc.
• The correct welding position.
• Proper travel speed.
O
nce the electrode is burned down turn the machine
off and remove the stub by opening the jaws of the
e
lectrode holder and insert a new electrode. The
welded work piece and electrode stub are hot after
welding, allow time to cool down before touching or
use pliers to move. Always make sure the AC 120 is
t
urned off before setting down the Electrode Holder.
ELECTRODE SELECTION
For best results use genuine Lincoln Electric
Fleetweld 37 electrodes in the 1/16" or 5/64" size.
This is suitable for welding up to 14ga steel.
LEARNING TO WELD
The serviceability of a product or structure utiliz-
ing this type of information is and must be the
sole responsibility of the builder/user. Many vari-
ables beyond the control of The Lincoln Electric
Company affect the results obtained in applying
this type of information. These variables include,
but are not limited to, welding procedure, plate
chemistry and temperature, weldment design, fab-
rication methods and service requirements.
No one can learn to weld simply by reading about it.
Skill comes only with practice. The following pages
will help the inexperienced welder to understand weld-
ing and develop his skill.
The Arc-Welding Circuit
The operator’s knowledge of arc welding must go
beyond the arc itself. He must know how to control the
arc, and this requires a knowledge of the welding cir-
cuit and the equipment that provides the electric cur-
rent used in the arc. Figure B.1 is a diagram of the
welding circuit. The circuit begins where the electrode
cable is attached to the welding machine and ends
where the work cable is attached to the welding
machine. Current flows through the electrode cable to
the electrode holder, through the holder to the elec-
trode and across the arc. On the work side of the arc,
the current flows through base metal to the work cable
and back to the welding machine. The circuit must be
complete for the current to flow. To weld, the work
clamp must be tightly connected to clean base metal.
Remove paint, rust, etc. as necessary to get a good
connection. Connect the work clamp as close as pos-
sible to the area you wish to weld. Avoid allowing the
welding circuit to pass through hinges, bearings, elec-
tronic components or similar devices that can be dam-
aged.
CENTURY® AC 120
WORKPIECE
WORK CABLE
ELECTRODE CABLE
ELECTRODE
ELECTRODE HOLDER
ARC
WORK CLAMP
CE
N
T
U
R
Y
WORKPIECE
WORK CABLE
ELECTRODE CABLE
ELECTRODE
ELECTRODE HOLDER
ARC
WORK CLAMP
CE
N
TU
R
Y
FIGURE B.1
B
-2
OPERATION
B
-2
ELECTRIC SHOCK can kill.
Carefully review the ARC WELDING
SAFETY PRECAUTIONS at the begin-
ning of this manual.
------------------------------------------------------------------------
The electric arc is made between the work and the tip
e
nd of a small metal wire, the electrode, which is
clamped in a holder. A gap is made in the welding cir-
cuit (see Figure B.1) by holding the tip of the elec-
trode.
Arc welding is a manual skill requiring a steady hand,
good physical condition, and good eyesight. The oper-
ator controls the welding arc and, therefore, the quali-
ty of the weld made.
What Happens in the Arc?
Figure B.2 illustrates the action that takes place in the
electric arc. It closely resembles what is actually seen
during welding.
The “arc stream’’ is seen in the middle of the picture.
This is the electric arc created by the electric current
flowing through the space between the end of the
electrode and the work. The temperature of this arc is
about 6000°F. (3315°C), which is more than enough
to melt metal. The arc is very bright, as well as hot,
and cannot be looked at with the naked eye without
risking painful injury. A very dark lens, specifically
designed for arc welding, must be used with a hand or
face shield whenever viewing the arc.
The arc melts the base metal and actually digs into it,
much as the water through a nozzle on a garden hose
digs into the earth. The molten metal forms a pool or
crater and tends to flow away from the arc. As it
moves away from the arc, it cools and solidifies. A
slag forms on top of the weld to protect it during cool-
ing.
The function of the covered electrode is much more
than simply to carry current to the arc. The electrode
is composed of a core of metal wire with an extruded
chemical covering.
T
he core wire melts in the arc and tiny droplets of
molten metal shoot across the arc into the molten
p
ool. The electrode provides additional filler metal for
the joint to fill the groove or gap between the two
pieces of the base metal. The covering also melts or
burns in the arc. It has several functions. It makes the
a
rc steadier, provides a shield of smoke-like gas
around the arc to keep oxygen and nitrogen in the air
a
way from the molten metal, and provides a flux for
the molten pool. The flux picks up impurities and
forms the protective slag.
Four simple manipulations are of prime impor-
tance. Without complete mastery of these four,
further welding is more or less futile. With com-
plete mastery of the four, welding will be easy.
1. The Correct Welding Position
Beginners will find it easier to learn how to control
the welding arc using the two-handed technique
shown below. This requires the use of a head-
shield.
a. Hold the electrode holder in your right hand.
b. Touch your left hand to the underside of your
right.
c. Put the left elbow against your left side.
(For welding left-handed it is the opposite.)
If you are using a hand shield, hold the electrode
holder in your right hand and the hand shield in your
left. (For welding left-handed it is the opposite.)
Whenever possible, weld from left to right (if right-
handed). This enables you to see clearly what you
are doing. Hold the electrode at a slight angle as
shown in Figure B.3.
2. The Correct Way to Strike an Arc
Be sure the work clamp makes good electrical con-
tact to the work.
CENTURY® AC 120
WARNING
FIGURE B.2
FIGURE B.3
SOLIDIFIED SLAG
BASE METAL
SHIELDING GASES
ELECTRODE
COVERING
WELD METAL
ARC
SOLIDIFIED SLAG
BASE METAL
SHIELDING GASES
ELECTRODE
COVERING
WELD METAL
ARC
B
-3
OPERATION
B
-3
NOTE: When welding on thin plate, you will find that
you will have to increase the welding speed, whereas
when welding on heavy plate, it is necessary to go
more slowly in order to get good penetration.
C
OMMON METALS
Most metals found around the home are low carbon
steel, sometimes referred to as mild steel. Typical
items made with this type of steel include most sheet
metal, plate, pipe and rolled shapes such as chan-
nels and angle irons. This type of steel can usually
be easily welded without special precautions.
Regardless of the type of metal being welded, in
order to get a quality weld, it is important that the
metal is free of oil, paint, rust or other contaminants.
Joint Types and Positions
Five types of welding joints are: Butt joint, Fillet joint,
Lap joint, Edge joint and Corner joint see Figure B.5.
Of these, the Butt joint and Fillet joint are the two
most common welds.
Butt Joints
Butt joints are the most widely used welds. Place two
plates side by side.
Tack the plates at both ends, otherwise the heat will
cause the plates to move apart. (See FIGURE B.6):
CENTURY® AC 120
FIGURE B.5
FIGURE B.6
Butt joint
Lap joint
Edge joint
Fillet joint
Corner joint
Butt joint
Lap joint
Edge joint
Fillet joint
Corner joint
Lower your headshield or hold the hand shield in front
of your face. Scratch the electrode slowly over the
metal and you will see sparks flying. While scratching,
lift the electrode 1/8" (3.2mm) and the arc is estab-
lished.
NOTE: If you stop moving the electrode while
scratching, the electrode will stick.
NOTE: Most beginners try to strike the arc by a fast
jabbing motion down on the plate. Result: They either
stick or their motion is so fast that they break the arc
immediately.
3. The Correct Arc Length
The arc length is the distance from the tip of the
electrode core wire to the base metal.
Once the arc has been established, maintaining the
correct arc length becomes extremely important. The
arc should be short, approximately 1/16 to 1/8" (1.6 to
3.2mm) long. As the electrode burns off the electrode
must be fed to the work to maintain correct arc
length.
The easiest way to tell whether the arc has the cor-
rect length is by listening to its sound. A nice, short
arc has a distinctive, “crackling” sound, very much
like eggs frying in a pan. The incorrect, long arc has a
hollow, blowing or hissing sound.
4. The Correct Welding Speed
The important thing to watch while welding is the
puddle of molten metal right behind the arc. Do
NOT watch the arc itself. It is the appearance of
the puddle and the ridge where the molten puddle
solidifies that indicate correct welding speed. The
ridge should be approximately 3/8" (9.5mm) behind
the electrode as shown in Figure B.4.
Most beginners tend to weld too fast, resulting in a
thin, uneven, “wormy” looking bead. They are not
watching the molten metal.
IMPORTANT: For general welding it is not necessary
to weave the arc; neither forwards and backwards nor
sideways. Weld along at a steady pace. You will find
it easier.
FIGURE B.4
B
-4
OPERATION
B
-4
Types of Butt Joint
Now weld the two plates together. Weld from left to
right (if right-handed). Point the electrode down in the
crack between the two plates, keeping the electrode
slightly tilted in the direction of travel. (See Figure
B.7)
Watch the molten metal to be sure it distributes itself
evenly on both edges and in between the plates.
Fillet Joint
When welding fillet joints, it is very important to hold
the electrode at a 45° angle between the two sides, or
the metal will not distribute itself evenly. (See Figure
B.8)
To make it easy to get the 45° angle, it is best to put
the electrode in the holder at a 45° angle, as shown:
Types of Fillet Joint
Multiple Pass Welds
Make multiple pass horizontal fillets as shown in fig-
ure B.9. Put the first bead in the corner. Hold the
electrode angle needed to deposit the filler beads as
shown putting the final bead against the vertical plate.
Make sure to remove the slag from the weld prior to
making the next pass.
CENTURY® AC 120
F
I
G
U
R
E
B
.
7
FI
GURE
B.9
FIG
URE
B.8
C
-1
TROUBLESHOOTING
C
-1
CENTURY® AC 120
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
This Troubleshooting Guide is provided to help you
locate and repair possible machine malfunctions.
Simply follow the three-step procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM (SYMP-
TOMS)”. This column describes possible symptoms
that the machine may exhibit. Find the listing that
best describes the symptom that the machine is
exhibiting.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists
the obvious external possibilities that may contribute
to the machine symptom.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the
Possible Cause, generally it states to contact your
local Authorized Field Service Facility.
If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your
local Authorized Field Service Facility.
HOW TO USE TROUBLESHOOTING GUIDE
S
ervice and Repair should only be performed by Factory Trained Personnel. Unauthorized repairs
performed on this equipment may result in danger to the technician and machine operator and will
invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all
safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
WARNING
C
-2
TROUBLESHOOTING
C
-2
CENTURY® AC 120
Observe all Safety Guidelines detailed throughout this manual
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
PROBLEMS
(SYMPTOMS)
POSSIBLE
CAUSE
RECOMMENDED
COURSE OF ACTION
Power source stops.
Power switch on but no weld cur-
rent.
Unstable arc.
Porous weld.
Thermal Overload Protection acti-
vated due to overload.
Bad connection between ground-
clamp and workpiece.
Impurities on base metal.
Dirty base metal.
The Thermal Protection automati-
cally resets when the transformer
has cooled (approximately 15 min-
utes)
Clean or wire brush the
work surface.
Clean with wire brush.
Clean with wire brush.
D
-1
WIRING DIAGRAMS
D
-1
CENTURY® AC 120
120 V
60 Hz
To earth ground in accordance with
National, local or other applicable
Electrical codes.
L1
N
G
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted
inside the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
WARNING
AVISO DE
PRECAUCION
ATTENTION
WARNUNG
ATENÇÃO
Spanish
French
G
erman
Portuguese
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE
CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE
ESTE EQUIPO Y LOS CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE
SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT
ET LES PRODUITS A ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE
EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRO-
DENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS
SIND EBENFALLS ZU BEACHTEN.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• Insulate yourself from work and
ground.
• No toque las partes o los electrodos
bajo carga con la piel o ropa moja-
da.
• Aislese del trabajo y de la tierra.
• Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
• Isolez-vous du travail et de la terre.
• Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
• Isolieren Sie sich von den
Elektroden und dem Erdboden!
• Não toque partes elétricas e electro-
dos com a pele ou roupa molhada.
• Isole-se da peça e terra.
• Keep flammable materials away.
• Mantenga el material combustible
fuera del área de trabajo.
• Gardez à l’écart de tout matériel
inflammable.
• Entfernen Sie brennbarres Material!
• Mantenha inflamáveis bem guarda-
dos.
• Wear eye, ear and body protection.
• Protéjase los ojos, los oídos y el
cuerpo.
• Protégez vos yeux, vos oreilles et
votre corps.
• Tragen Sie Augen-, Ohren- und Kör-
perschutz!
• Use proteção para a vista, ouvido e
corpo.
R A
WARNING
AVISO DE
PRECAUCION
ATTENTION
WARNUNG
ATENÇÃO
S
panish
French
G
erman
Portuguese
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES
DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Keep your head out of fumes.
• Use ventilation or exhaust to
remove fumes from breathing zone.
• Los humos fuera de la zona de res-
piración.
• Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
• Gardez la tête à l’écart des fumées.
• Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
• Vermeiden Sie das Einatmen von
Schweibrauch!
• Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
• Mantenha seu rosto da fumaça.
• Use ventilação e exhaustão para
remover fumo da zona respiratória.
• Turn power off before servicing.
• Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
• Débranchez le courant avant l’entre-
tien.
• Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öffnen;
Maschine anhalten!)
•
Não opere com as tampas removidas.
•
Desligue a corrente antes de fazer
serviço.
•
Não toque as partes elétricas nuas.
• Do not operate with panel open or
guards off.
• No operar con panel abierto o
guardas quitadas.
• N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
• Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
• Mantenha-se afastado das partes
moventes.
• Não opere com os paineis abertos
ou guardas removidas.
• Century
®
Equipment
2345 Murphy Blvd. Gainesville, GA 30504 TEL: 866-236-0044
Web Site: www.centuryequipment.net
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Century Century AC 120 Mode d'emploi
- Catégorie
- Système de soudage
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
Lincoln Electric LN-25 Pro Mode d'emploi
-
Lincoln Electric Red-D-Arc DC655e Mode d'emploi
-
-
-
-
-
-
-
-