Lincoln Electric Bulldog 140 Manuel utilisateur

Marque: Lincoln Electric

Modèle: Bulldog 140

Catégorie: Système de soudage

Taper: Manuel utilisateur

OPERATOR’S MANUAL

Safety Depends on You

Lincoln arc welding and cutting

equipment is designed and built

with safety in mind. However, your

overall safety can be increased by

proper installation ... and thought-

ful operation on your part. DO

NOT INSTALL, OPERATE OR

REPAIR THIS EQUIPMENT

WITHOUT READING THIS

MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED

THROUGHOUT. And, most

importantly, think before you act

and be careful.

BULLDOG ™140

For Machines with Code Number 11518

IM10005

June, 2009

Various engine configurations are available and machine appearance will vary

accordingly.

ISO 9001

CERTIFICATE NUMBER: 30273

Designed and Manufactured Under a

Quality Program Certified by

ABS Quality Evaluations, Inc.

to ISO 9001 Requirements.

QMS

ANSI RAB

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

This manual covers equipment which is no

longer in production by The Lincoln Electric Co.

Specications and availability of optional

features may have changed.

THANK YOU FOR SELECTING

A QUALITY PRODUCT BY

LINCOLN ELEC TRIC.

PLEASE EXAMINE CARTON AND EQUIPMENT FOR

DAMAGE IMMEDIATELY

When this equipment is shipped, title passes to the purchaser

upon receipt by the carrier. Consequently, claims for material

damaged in shipment must be made by the purchaser against the

transportation company at the time the shipment is received.

SAFETY DEPENDS ON YOU

Lincoln arc welding and cutting equipment is designed and built

with safety in mind. However, your overall safety can be increased

by proper installation ... and thoughtful operation on your part.

DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT

WITHOUT READING THIS MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,

think before you act and be careful.

This statement appears where the information must be followed

exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed

to avoid minor personal injury or damage to this equipment.

KEEP YOUR HEAD OUT OF THE FUMES.

DON’T get too close to the arc.

Use corrective lenses if necessary

to stay a reasonable distance

away from the arc.

READ and obey the Safety Data

Sheet (SDS) and the warning label

that appears on all containers of

welding materials.

USE ENOUGH VENTILATION or

exhaust at the arc, or both, to

keep the fumes and gases from

your breathing zone and the general area.

IN A LARGE ROOM OR OUTDOORS, natural ventilation may be

adequate if you keep your head out of the fumes (See below).

USE NATURAL DRAFTS or fans to keep the fumes away

from your face.

If you de velop unusual symptoms, see your supervisor.

Perhaps the welding atmosphere and ventilation system

should be checked.

WEAR CORRECT EYE, EAR &

BODY PROTECTION

PROTECT your eyes and face with welding helmet

properly fitted and with proper grade of filter plate

(See ANSI Z49.1).

PROTECT your body from welding spatter and arc

flash with protective clothing including woolen

clothing, flame-proof apron and gloves, leather

leggings, and high boots.

PROTECT others from splatter, flash, and glare

with protective screens or barriers.

IN SOME AREAS, protection from noise may be appropriate.

BE SURE protective equipment is in good condition.

Also, wear safety glasses in work area

AT ALL TIMES.

SPECIAL SITUATIONS

DO NOT WELD OR CUT containers or materials which previously

had been in contact with hazardous substances unless they are

properly cleaned. This is extremely dangerous.

DO NOT WELD OR CUT painted or plated parts unless special

precautions with ventilation have been taken. They can release

highly toxic fumes or gases.

Additional precautionary measures

PROTECT compressed gas cylinders from excessive heat,

mechanical shocks, and arcs; fasten cylinders so they cannot fall.

BE SURE cylinders are never grounded or part of an

electrical circuit.

REMOVE all potential fire hazards from welding area.

ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR

IMMEDIATE USE AND KNOW HOW TO USE IT.

WARNING

CAUTION

Safety 01 of 04 - 5/16/2018

SECTION A:

WARNINGS

CALIFORNIA PROPOSITION 65 WARNINGS

WARNING: Breathing diesel engine exhaust

exposes you to chemicals known to the State

of California to cause cancer and birth defects,

or other reproductive harm.

• Always start and operate the engine in a

well-ventilated area.

• If in an exposed area, vent the exhaust to the outside.

• Do not modify or tamper with the exhaust system.

• Do not idle the engine except as necessary.

For more information go to

www.P65 warnings.ca.gov/diesel

WARNING: This product, when used for welding or

cutting, produces fumes or gases which contain

chemicals known to the State of California to cause

birth defects and, in some cases, cancer. (California

Health & Safety Code § 25249.5 et seq.)

WARNING: Cancer and Reproductive Harm

www.P65warnings.ca.gov

ARC WELDING CAN BE HAZARDOUS. PROTECT

YOURSELF AND OTHERS FROM POSSIBLE SERIOUS

INJURY OR DEATH. KEEP CHILDREN AWAY.

PACEMAKER WEARERS SHOULD CONSULT WITH

THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For

additional safety information, it is strongly recommended

that you purchase a copy of “Safety in Welding & Cutting -

ANSI Standard Z49.1” from the American Welding Society,

P.O. Box 351040, Miami, Florida 33135 or CSA Standard

W117.2-1974. A Free copy of “Arc Welding Safety” booklet

E205 is available from the Lincoln Electric Company,

22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION,

MAINTENANCE AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE POWERED

EQUIPMENT.

1.a. Turn the engine off before troubleshooting

and maintenance work unless the

maintenance work requires it to be running.

1.b. Operate engines in open, well-ventilated areas or vent the engine

exhaust fumes outdoors.

1.c. Do not add the fuel near an open flame welding

arc or when the engine is running. Stop the

engine and allow it to cool before refueling to

prevent spilled fuel from vaporizing on contact

with hot engine parts and igniting. Do not spill fuel when filling

tank. If fuel is spilled, wipe it up and do not start engine until

fumes have been eliminated.

1.d. Keep all equipment safety guards, covers

and devices in position and in good repair.

Keep hands, hair, clothing and tools away

from V-belts, gears, fans and all other

moving parts when starting, operating or

repairing equipment.

1.e. In some cases it may be necessary to remove safety guards to

perform required maintenance. Remove guards only when

necessary and replace them when the maintenance requiring

their removal is complete. Always use the greatest care when

working near moving parts.

1.f. Do not put your hands near the engine fan. Do not attempt to

override the governor or idler by pushing on the throttle control

rods while the engine is running.

1.g. To prevent accidentally starting gasoline engines while turning

the engine or welding generator during maintenance work,

disconnect the spark plug wires, distributor cap or magneto wire

as appropriate.

1.h. To avoid scalding, do not remove the radiator

pressure cap when the engine is

hot.

ELECTRIC AND

MAGNETIC FIELDS MAY

BE DANGEROUS

2.a. Electric current flowing through any conductor

causes localized Electric and Magnetic Fields (EMF).

Welding current creates EMF fields around welding cables

and welding machines

2.b. EMF fields may interfere with some pacemakers, and

welders having a pacemaker should consult their physician

before welding.

2.c. Exposure to EMF fields in welding may have other health effects

which are now not known.

2.d. All welders should use the following procedures in order to

minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure

them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work

cables. If the electrode cable is on your right side, the

work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as pos-

sible to the area being welded.

2.d.5. Do not work next to welding power source.

SAFETY

Safety 02 of 04 - 5/16/2018

ELECTRIC SHOCK

CAN KILL.

3.a. The electrode and work (or ground) circuits are

electrically “hot” when the welder is on. Do

not touch these “hot” parts with your bare skin or wet clothing.

Wear dry, hole-free gloves to insulate hands.

3.b. Insulate yourself from work and ground using dry insulation.

Make certain the insulation is large enough to cover your full area

of physical contact with work and ground.

In addition to the normal safety precautions, if

welding must be performed under electrically

hazardous conditions (in damp locations or while

wearing wet clothing; on metal structures such as

floors, gratings or scaffolds; when in cramped

positions such as sitting, kneeling or lying, if there

is a high risk of unavoidable or accidental contact

with the workpiece or ground) use the following

equipment:

• Semiautomatic DC Constant Voltage (Wire) Welder.

• DC Manual (Stick) Welder.

• AC Welder with Reduced Voltage Control.

3.c. In semiautomatic or automatic wire welding, the electrode,

electrode reel, welding head, nozzle or semiautomatic welding

gun are also electrically “hot”.

3.d. Always be sure the work cable makes a good electrical

connection with the metal being welded. The connection should

be as close as possible to the area being welded.

3.e. Ground the work or metal to be welded to a good electrical (earth)

ground.

3.f. Maintain the electrode holder, work clamp, welding cable and

welding machine in good, safe operating condition. Replace

damaged insulation.

3.g. Never dip the electrode in water for cooling.

3.h. Never simultaneously touch electrically “hot” parts of electrode

holders connected to two welders because voltage

between the

two can be the total of the open circuit voltage of both

welders.

3.i. When working above floor level, use a safety belt to protect

yourself from a fall should you get a shock.

3.j. Also see It ems 6.c. and 8.

ARC RAYS CAN BURN.

4.a. Use a shield with the proper filter and cover plates to protect your

eyes from sparks and the rays of the arc when welding or

observing open arc welding. Headshield and filter lens should

conform to ANSI Z87. I standards.

4.b. Use suitable clothing made from durable flame-resistant material

to protect your skin and that of your helpers from the arc rays.

4.c. Protect other nearby personnel with suitable, non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

FUMES AND GASES

CAN BE DANGEROUS.

5.a. Welding may produce fumes and gases

hazardous to health. Avoid breathing these

fumes and gases. When welding, keep your head out of the fume.

Use enough ventilation and/or exhaust at the arc to keep fumes

and gases away from the breathing zone. When welding

hardfacing (see instructions on container or SDS)

or on lead or cadmium plated steel and other

metals or coatings which produce highly toxic

fumes, keep exposure as low as possible and

within applicable OSHA PEL and ACGIH TLV limits

using local exhaust or mechanical ventilation

unless exposure assessments indicate otherwise.

In confined spaces or in some circumstances,

outdoors, a respirator may also be required.

Additional precautions are also required when

welding

on galvanized steel.

5. b. The operation of welding fume control equipment is affected by

various factors including proper use and positioning of the

equipment, maintenance of the equipment and the specific

welding procedure and application involved. Worker exposure

level should be checked upon installation and periodically

thereafter to be certain it is within applicable OSHA PEL and

ACGIH TLV limits.

5.c. Do not weld in locations near chlorinated hydrocarbon vapors

coming from degreasing, cleaning or spraying operations. The

heat and rays of the arc can react with solvent vapors to form

phosgene, a highly toxic gas, and other irritating products.

5.d. Shielding gases used for arc welding can displace air and

cause

injury or death. Always use enough ventilation, especially in

confined areas, to insure breathing air is safe.

5.e. Read and understand the manufacturer’s instructions for this

equipment and the consumables to be used, including the

Safety Data Sheet (SDS) and follow your employer’s safety

practices. SDS forms are available from your welding

distributor or from the manufacturer.

5.f. Also see item 1.b.

SAFETY

Safety 03 of 04 - 5/16/2018

WELDING AND CUTTING

SPARKS CAN CAUSE

FIRE OR EXPLOSION.

6.a. Remove fire hazards from the welding area. If

this is not possible, cover them to prevent the welding sparks

from starting a fire. Remember that welding sparks and hot

materials from welding can easily go through small cracks and

openings to adjacent areas. Avoid welding near hydraulic lines.

Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special

precautions should be used to prevent hazardous situations.

Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)

and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is

touching the work or ground. Accidental contact can cause

overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the

proper steps have been taken to insure that such procedures

will not cause flammable or toxic vapors from substances inside.

They can cause an explosion even though they have been

“cleaned”. For information, purchase “Recommended Safe

Practices for the Preparation for Welding and Cutting of

Containers and Piping That Have Held Hazardous Substances”,

AWS F4.1 from the American Welding Society

(see address above).

6.e. Vent hollow castings or containers before heating, cutting or

welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free

protective garments such as leather gloves, heavy shirt, cuffless

trousers, high shoes and a cap over your hair. Wear ear plugs

when welding out of position or in confined places. Always wear

safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area

as practical. Work cables connected to the building framework or

other locations away from the welding area increase the

possibility of the welding current passing through lifting chains,

crane cables or other alternate circuits. This can create fire

hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

6.I. Read and follow NFPA 51B “Standard for Fire Prevention During

Welding, Cutting and Other Hot Work”, available from NFPA, 1

Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.

6.j. Do not use a welding power source for pipe thawing.

CYLINDER MAY EXPLODE IF

DAMAGED.

7.a. Use only compressed gas cylinders containing

the correct shielding gas for the process used

and properly operating regulators designed for

the gas and pressure used. All hoses, fittings,

etc. should be suitable for the application and

maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to

an undercarriage or fixed support.

7.c. Cylinders should be located:

• Away from areas where they may be struck or subjected

to physical damage.

• A safe distance from arc welding or cutting operations

and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other

electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight

except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders,

associated equipment, and CGA publication P-l, “Precautions for

Safe Handling of Compressed Gases in Cylinders,” available from

the Compressed Gas Association, 14501 George Carter Way

Chantilly, VA 20151.

FOR ELECTRICALLY

POWERED EQUIPMENT.

8.a. Turn off input power using the disconnect

switch at the fuse box before working on

the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical

Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

Refer to

http://www.lincolnelectric.com/safety

for additional safety information.

SAFETY

Safety 04 of 04 - 5/16/2018

SAFETY

Mar. ‘93

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instruc-

tions et les précautions de sûreté specifiques qui parraissent

dans ce manuel aussi bien que les précautions de sûreté

générales suivantes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une

grande partie du corps peut être en contact avec la

masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à soud-

er parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode s’applicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se pro-

téger contre les chutes dans le cas ou on recoit un choc. Ne

jamais enrouler le câble-électrode autour de n’importe quelle

partie du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du

rayonnement de l’arc et des projections quand on soude

ou quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflamma-

bles.

4. Des gouttes de laitier en fusion sont émises de l’arc de

soudage. Se protéger avec des vêtements de protection

libres de l’huile, tels que les gants en cuir, chemise épaisse,

pantalons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible

de la zone de travail qu’il est pratique de le faire. Si on place

la masse sur la charpente de la construction ou d’autres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques d’incendie ou d’echauffement des chaines et des

câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

d’opérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de l’arc peuvent réagir avec les

vapeurs du solvant pour produire du phosgéne (gas forte-

ment toxique) ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code

de l’électricité et aux recommendations du fabricant. Le dis-

positif de montage ou la piece à souder doit être branché à

une bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste

seront effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la

debrancher à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

Page

Safety i-iv

Installation .............................................................................................................................Section A

Technical Specifications .............................................................................................................A-1

Safety Precautions......................................................................................................................A-2

Location and Ventilation .............................................................................................................A-2

Stacking, tilting and Lifting .........................................................................................................A-3

Pre-operation Engine Service .....................................................................................................A-3

Oil, Fuel and Spark Arrester........................................................................................................A-3

Electrical Output Connections and Welding Cable Size, Lengths..............................................A-4

Machine Grounding and Auxiliary Power Receptacles...............................................................A-5

Premises Wiring and Circuit Breakers ........................................................................................A-6

Electrical Devises used with the BULLDOG™ 140.....................................................................A-7

Operation...............................................................................................................................Section B

Safety Instructions ......................................................................................................................B-1

General Description ....................................................................................................................B-1

Recommended Applications.......................................................................................................B-1

Operational Features and Controls.............................................................................................B-1

Welding Capability......................................................................................................................B-1

Limitations .................................................................................................................................B-2

Controls and Settings .................................................................................................................B-2

Gasoline Engine Conrtols, Engine Operation ..............................................................B-3 Thru B-6

Welding Operation and Welding Guidelines..............................................................B-7 Thru B-16

Accessories...........................................................................................................................Section C

Options/Accessories ...................................................................................................................C-1

Maintenance..........................................................................................................................Section D

Safety Precautions......................................................................................................................D-1

Routine and Periodic Maintenance ..............................................................................D-1 thru D-4

General Assembly Exploded View..............................................................................................D-5

Troubleshooting and Repair ................................................................................................Section E

Electrical Diagram and Dimension Print.............................................................................Section F

Parts Manual (Robin / Subaru) ......................................................................................P-615 Series

TABLE OF CONTENTS

vi vi

BULLDOG™ 140

TECHNICAL SPECIFICATIONS - BULLDOG™ 140 K2708-1

Manufacturer Description Speed Displacement Ignition Capacities

Robin / Subaru 1 cyl., 3700 RPM 17.51 cu. in. Manual,

Fuel: 6.86 gal. (24.9 l)

EX 30 4 cycle ± 50 RPM (287 cc) Recoil start;

Code air-cooled at no load Manual choke Oil: 1.1 qts.(1.0 l)

(11518) OHC gasoline Bore x Stroke

10 HP @ 2.95” x 2.56”

3600 RPM (76mm x 65mm)

Aluminum Block

with Cast Iron

Sleeve

Duty Cycle Amps AC Volts at Rated Amperes

30% Duty Cycle 125 Amps AC Constant Current 20 VAC

60% Duty Cycle 100 Amps AC Constant Current 25 VAC

Welding Ranges Welder Open Circuit Voltage AC Auxiliary Power

70 - 140 Amps AC 66 VAC Max. 4000 Continuous Watts

5500 Surge Watts

Height Width Depth Weight

25.47 in. 21.12 in. 31.48 in. 205 lb.

646 mm 536.45 mm 799.59 mm 93 kg

A-1

INSTALLATION

BULLDOG™ 140

A-1

INPUT - GASOLINE ENGINE

RATED OUTPUT - WELDER

OUTPUT - WELDER AND GENERATOR

PHYSICAL DIMENSIONS

A-2

INSTALLATION

BULLDOG™ 140

A-2

SAFETY PRECAUTIONS

Read this entire installation section before you

start installation.

Do not attempt to use this equipment until you

have thoroughly read all the operation and main-

tenance manuals supplied with your machine.

They include important safety precautions;

detailed engine starting, operating, and mainte-

nance instructions; and parts lists.

ELECTRIC SHOCK can kill.

• Do not touch electrically live

parts or electrodes with your

skin or wet clothing.

• Insulate yourself from the

work and ground.

•Always wear dry insulating gloves.

ENGINE EXHAUST can kill.

• Use in open, well ventilated

areas or vent exhaust to the

outside.

• Do not stack anything on or

near the engine.

MOVING PARTS can injure.

• Do not operate this equip-

ment with any of its doors

open or guards off.

• Stop the engine before ser-

vicing it.

• Keep away from moving parts.

Only qualified personnel should install, use, or service

this equipment.

LOCATION AND VENTILATION

Whenever you use the BULLDOG™ 140, be sure that

clean cooling air can flow through the machine’s

gasoline engine and the generator. Avoid dusty, dirty

areas. Also, keep the machine away from heat

sources. Do not place the back end of the generator

anywhere near hot engine exhaust from another

machine. And of course, make sure that engine

exhaust is ventilated to an open, outside area.

The BULLDOG™ 140 must be used outdoors. Do

not set the machine in puddles or otherwise sub-

merge it in water. Such practices pose safety haz-

ards and cause improper operation and corrosion of

parts.

Always operate the BULLDOG™ 140 with the case

roof on and all machine components completely

assembled. This will protect you from the dangers of

moving parts, hot metal surfaces, and live electrical

devices.

STORING

1. Store the machine in a cool, dry place when it’s

not in use. Protect it from dust and dirt. Keep it

where it can’t be accidentally damaged from con-

struction activities, moving vehicles, and other

hazards.

2. If you will be storing the machine for over 30

days, you should drain the fuel to protect fuel

system and carburetor parts from gum deposits.

Empty all fuel from the tank and run the engine

until it stops from lack of fuel.

3. You can store the machine for up to 24 months if

you use a gasoline stabilizing additive in the fuel

system. Mix the additive with the fuel in the tank

and run the engine for a short time to circulate

the additive through the carburetor.

4. While the engine is still warm, drain the oil and

refill with fresh oil per the engine manual.

5. Remove the spark plug and pour approximately

1/2 ounce (15 ml) of engine oil into the cylinder.

Replace the spark plug and crank the engine

slowly to distribute the oil.

6. Clean any dirt and debris from the cylinder and

cylinder head fins and housing, rotating screen,

and muffler areas.

7. Store in a clean, dry area.

WARNING

Robin / Subaru 10 HP Carb.

Certified

EX 30

.31 Gallons/Hour

(1.16 Liters/Hour)

.53 Gallons/Hour

(2.02 Liters/Hour)

.70 Gallons/Hour

(2.65 Liters/Hour)

No Load

3750 RPM ±100 R.P.M.

AC CC Weld Output

80 Amps @ 25 Volts

Auxiliary Power 4000

Watts (120/240 Volts)

BULLDOG™ 140 Typical Fuel

Consumption

A-3

INSTALLATION

BULLDOG™ 140

A-3

SPARK ARRESTER

Some federal, state or local laws may require gaso-

line engines to be equipped with exhaust spark

arresters when they are operated in certain locations

where unarrested sparks may present a fire hazard.

The standard muffler included with this machine does

qualify as a spark arrester.

WARNING

• Keep hands away from muffler or HOT engine

parts.

• Stop the engine when fueling.

• Do not smoke when fueling.

• Remove fuel cap slowly to release pressure.

• Do not overfill tank.

• Wipe up spilled fuel and allow fumes to clear

before starting engine.

• Keep sparks and flame away from tank.

------------------------------------------------------------------------

PRE-OPERATION ENGINE SERVICE

Read and understand the engine operating and

maintenance instructions supplied with this machine

before you operate the BULLDOG™ 140.

OIL

The BULLDOG™ 140 is shipped with the engine

filled with SAE 10W30 oil. CHECK THE OIL LEVEL

BEFORE YOU START THE ENGINE. This is an

added precaution. Do not screw in dipstick when

checking oil level. DO NOT OVERFILL. Be sure the

fill plug is tight after servicing.

FUEL

Fill the fuel tank with clean, fresh, regular grade (mini-

mum 87 octane lead free gasoline. DO NOT MIX OIL

WITH GAS. The BULLDOG™ 140 capacity is approxi-

mately 6.8 gallons (25.74 Liter). DO NOT OVERFILL,

allow room in the fuel tank for fuel expansion.

STACKING

BULLDOG™ 140 machines CANNOT be stacked.

TILTING

Place the machine on a secure, level surface whenev-

er you use it or store it. Any surfaces you place it on

other than the ground must be firm, non-skid, and

structurally sound.

The gasoline engine is designed to run in a level posi-

tion for best performance. It can operate at an angle,

but this should never be more than 15 degrees in any

direction. If you do operate it at a slight angle, be sure

to check the oil regularly and keep the oil level full.

Also, fuel capacity will be a little less at an angle.

LIFTING

The BULLDOG™ 140 should be lifted by two people.

(See Specification section for weight). The LowLift™

grab bars on both ends make lifting easier.

A-4

INSTALLATION

BULLDOG™ 140

A-4

ELECTRICAL OUTPUT

CONNECTIONS

See Figure A.1 for the location of the current control

dial, weld output terminals, ground stud, circuit

breakers, 240 and 120 volt receptacles.

WELDING CABLE CONNECTIONS

Cable Size and Length

Be sure to use welding cables that are large enough.

The correct size and length becomes especially

important when you are welding at a distance from

the welder.

Table A.1 lists recommended cable sizes and lengths

for rated current and duty cycle. Length refers to the

distance from the welder to the work and back to the

welder. Cable diameters are increased for long cable

lengths to reduce voltage drops.

BULLDOG™ 140 OUTPUT CONNECTIONS

1. CURRENT CONTROL DIAL

2. WELD OUTPUT TERMINALS (2)

3. GROUND STUD

4. CIRCUIT BREAKER 20 Amp

5. RECEPTACLE - 240 VOLT, 50 AMP

6. DUPLEX RECEPTACLE (2)- 120 VOLT, 20

AMP

7. HOUR METER

FIGURE A.1

TOTAL COMBINED LENGTH OF

ELECTRODE AND WORK CABLES

Cable

Length

0-50 ft (0-15m)

50-100 ft (15-30 m)

100-150 ft (30-46 m)

150-200 ft (46-61 m)

200-250 ft (61-76m)

125 Amps

30% Duty Cycle

6 AWG

5 AWG

3 AWG

2 AWG

1 AWG

TABLE A.1

RECOMMENDED WELDING CABLE

SIZE AND LENGTH

A-5

INSTALLATION

BULLDOG™ 140

A-5

Cable Installation

Install the welding cables to your BULLDOG™ 140 as

follows. See Figure A.1 for the location of parts.

1. The gasoline engine must be OFF to install weld-

ing cables.

2. Remove the 1/2 - 13 flanged nuts from the output

terminals.

3. Connect the electrode holder and work cables to

the weld output terminals. You can connect either

cable to either terminal, since the BULLDOG™

140 provides AC weld current.

4. Tighten the flanged nuts securely.

5. Be certain that the metal piece you are welding

(the “work”) is securely connected to the work

clamp and cable.

6. Check and tighten the connections periodically.

• Loose connections will cause the output termi-

nals to overheat. The terminals may eventually

melt.

• Do not cross the welding cables at the output

terminal connection. Keep the cables isolated

and separate from one another.

-----------------------------------------------------------

Lincoln Electric offers a welding accessory kit with

the properly specified welding cables. See the

ACCESSORIES section of this manual for more infor-

mation.

ELECTRICAL CONNECTIONS

MACHINE GROUNDING

Because this portable engine driven welder creates its

own power, it is not necessary to connect its frame to

an earth ground, unless the machine is connected to

premises wiring (home, shop, etc.)

To prevent dangerous electric shock, other equipment

to which this engine driven welder supplies power

must:

1. Be grounded to the frame of the welder using a

grounded type plug.

2. Be double insulated.

Do not ground the machine to a pipe that carries

explosive or combustible material.

-----------------------------------------------------------------------

When the BULLDOG™ 140 is mounted on a truck or

a trailer, the machine generator ground stud MUST

be securely connected to the metal frame of the vehi-

cle. See Figure A.1. The ground stud is marked with

the symbol .

PLUGS AND HAND-HELD EQUIPMENT

For further protection against electric shock, any

electrical equipment connected to the generator

receptacles must use a three-blade, grounded type

plug or an Underwriter’s Laboratories (UL) approved

double insulation system with a two-blade plug.

Ground fault protection is recommended for hand

held equipment.

Never operate this machine with damaged or

defective cords. All electrical equipment must be

in safe condition.

-----------------------------------------------------------

AUXILIARY POWER RECEPTACLES

The control panel of the BULLDOG™ 140 features

two auxiliary power receptacles:

• A 20 amp, 120 volt duplex (double outlet) recepta-

cle

• A 20 amp 240 volt simplex (single outlet) recepta-

cle.

See Figure A.1.

Through these receptacles the machine can supply

up to 4,000 rated continuous watts and 5,500 surge

watts of single-phase AC power.

CAUTION

WARNING

A-6

INSTALLATION

BULLDOG™ 140

A-6

PREMISES WIRING

The BULLDOG™ 140 is not recommended for

premises wiring.

The BULLDOG™ 140 does not have a combined

120/240 volt receptacle and cannot be connected to

a premises as described in other Lincoln literature.

Remember that the BULLDOG™ 140 is intended only

for backup, intermittent use power.

Certain electrical devices cannot be powered by the

BULLDOG™ 140. Refer to Table A.2 for these

devices.

CIRCUIT BREAKERS

Auxiliary power is protected by circuit breakers.

When the machine is operated in high temperature

environments, the breakers may tend to trip at lower

loads than normally.

Never bypass the circuit breakers. Without over-

load protection, the BULLDOG™ 140 could over-

heat and/or cause damage to the equipment being

used.

-------------------------------------------------------------

CAUTION

A-7

INSTALLATION

BULLDOG™ 140

A-7

CAUTION

Certain Electrical devices cannot be powered by the BULLDOG™ 140. See Table A.2.

TABLE A.2

ELECTRICAL DEVICE USE WITH THE BULLDOG™ 140.

Type Common Electrical Devices Possible Concerns

Resistive Heaters, toasters, incandescent NONE

light bulbs, electric range, hot

pan, skillet, coffee maker.

Capacitive TV sets, radios, microwaves, Voltage spikes or high voltage

appliances with electrical control. regulation can cause the capaci-

tative elements to fail. Surge

protection, transient protection,

and additional loading is recom-

mended for 100% fail-safe

operation. DO NOT RUN

THESE DEVICES WITHOUT

ADDITIONAL RESISTIVE TYPE

LOADS.

Inductive Single-phase induction motors, These devices require large

drills, well pumps, grinders, small current inrush for starting. (See

refrigerators, weed and hedge Table B.3, GENERATOR POWER

trimmers APPLICATIONS, in the OPERA-

TION section of this manual for

required starting wattages.)

Some synchronous motors may

be frequency sensitive to attain

maximum output torque, but

they SHOULD BE SAFE from

any frequency induced failures.

Capacitive/Inductive Computers, high resolution TV sets, An inductive type line condition-

complicated electrical equipment. er along with transient and

surge protection is required, and

liabilities still exist. DO NOT

USE THESE DEVICES WITH A

BULLDOG™ 140.

The Lincoln Electric Company is not responsible for any damage to electrical components improperly connect-

ed to the BULLDOG™ 140.

B-1

OPERATION

B-1

SAFETY INSTRUCTIONS

Read and understand this entire section before oper-

ating your BULLDOG™ 140.

Do not attempt to use this equipment until you

have thoroughly read all the operation and main-

tenance manuals supplied with your machine.

They include important safety precautions;

detailed engine starting, operating, and mainte-

nance instructions; and parts lists.

ELECTRIC SHOCK can kill.

• Do not touch electrically live parts

or electrodes with your skin or wet

clothing.

• Insulate yourself from the work and ground.

• Always wear dry insulating gloves.

FUMES AND GASES can be

dangerous.

• Keep your head out of fumes.

• Use ventilation or exhaust to

remove fumes from breathing zone.

WELDING SPARKS can cause

fire or explosion.

• Keep flammable material away.

• Do not weld on containers that have

held combustibles.

ARC RAYS can burn.

• Wear eye, ear, and body protection.

ENGINE EXHAUST can kill.

• Use in open, well ventilated areas or

vent exhaust to the outside.

• Do not stack anything on or near the

engine.

MOVING PARTS can injure.

• Do not operate this equipment with

any of its doors open or guards off.

• Stop the engine before servicing it.

• Keep away from moving parts.

OOnnllyy qquuaalliiffiieedd ppeerrssoonnnneell sshhoouulldd iinnssttaallll,, uussee,, oorr sseerr--

vviiccee tthhiiss eeqquuiippmmeenntt..

GENERAL DESCRIPTION

The BULLDOG™ 140 is a generator/welder designed for

home use and other non-commercial applications. As a

generator it can supply up to 4,000 continuous watts (or

5,500 surge watts) of 120/240 volt, single-phase AC power.

As a welder it provides 125 amps of AC constant current for

welding with AC stick electrodes. A single dial provides

continuous adjustment of welding output. The machine is

lightweight, portable, and can be lifted by two people.

The Lincoln warranty covers the BULLDOG™ 140 (exclud-

ing the engine) for 3 years from the date of purchase. The

engine is covered by the engine manufacturer’s warranty

policy.

RECOMMENDED APPLICATIONS

GENERATOR

The BULLDOG™ 140 gives AC generator output for medi-

um use, non-commercial demands. For more details on

operating the generator, see GENERATOR OPERATION in

the OPERATION section of this manual.

WELDER

The BULLDOG™ 140 provides excellent constant current

AC welding output for stick (SMAW) welding. For more

details on using the machine as a welder, see WELDING

OPERATION in the OPERATION section of this manual.

OPERATIONAL FEATURES AND

CONTROLS

The BULLDOG™ 140 was designed for simplicity.

Therefore, it has very few operating controls. A single dial

on the control panel lets you select either generator or

welding use. For welding, the same dial selects continuous

current output over the machine’s 70 to 125 amp range.

The gasoline engine controls include a recoil starter, choke,

and rotary stop switch. See ENGINE OPERATION in the

OPERATION section of this manual and the engine owner’s

manual for details about starting, running, stopping, and

breaking in the gasoline engine.

WELDING CAPABILITY

The BULLDOG™ 140 is rated 125 amps, 20 volts at 30%

duty cycle on a ten-minute basis. This means that you can

load the welder to 125 amps for three minutes out of every

ten-minute period. The machine is also capable of higher

duty cycles at lower output currents. You can load the

welder to 100 amps for six minutes out of ten for a 60%

duty cycle.

The current is continuously variable from 70 to 125 amps

AC. The BULLDOG™ 140 can weld with all

3/32 and most

1/8 inch diameter Lincoln AC electrodes.

BULLDOG™ 140

WARNING

B-2

OPERATION

B-2

LIMITATIONS

• The BULLDOG™ 140 is not recommended for any

processes besides those that are normally per-

formed using stick welding (SMAW) procedures.

• The BULLDOG™ 140 is not recommended for pipe

thawing.

• During welding, generator power is limited to 100

watts, and output voltages can drop from 120 to 80

volts and 240 to 160 volts. Therefore, DO NOT

OPERATE ANY SENSITIVE ELECTRICAL EQUIP-

MENT WHILE YOU ARE WELDING.

BULLDOG™ 140

CONTROLS AND SETTINGS

All welder/generator controls are located on the Output

Control Panel. Gasoline engine controls are mounted on

the engine. See Figure B.1 and the figures in engine

operation section.

WELDER/GENERATOR CONTROLS

See Figure B.1 for the location of the following features:

1. CURRENT CONTROL DIAL: Adjusts continuous

current output. The amperages on the dial corre-

spond to the approximate amperages needed for

specific Lincoln welding electrodes.

2. 20 AMP CIRCUIT BREAKER: Provide separate over-

load current protection for the 120 Volt and 240 Volt

Receptacles

3. WELD ELECTRODE OUTPUT TERMINAL: Pro vides

the connection point for the electrode holder cable.

4. WELD WORK OUTPUT TERMINAL: Provides the

connection point for the work cable.

5. GROUND STUD: Provides a connection point for

connecting the machine case to earth ground.

6. 240 VOLT RECEPTACLE: Connection point for sup

240 Volt power to operate one electrical device.

7. 120 VOLT DUPLEX RECEPTACLES (2): Connection

point for supplying 120 Volt power.

8. HOUR METER: Records the time that the engine has

run for maintenance purposes.

OUTPUT PANEL CONTROLS

FIGURE B.1

B-3

OPERATION

B-3

BULLDOG™ 140

GASOLINE ENGINE CONTROLS

Refer to your engine manual for the location of the

following features:

1. FUEL SHUTOFF VALVE: Stops the flow of gaso-

line from the fuel tank to the carburetor. Should

be closed whenever you are finished using the

BULLDOG™ 140. Must be opened before you

start the engine.

2. FUEL TANK AND CAP: See TECHNICAL SPECI-

FICATIONS for capacity.

NOTE: If you use any other alternate fuel tank or

supply, be sure to use a recommended in-

line fuel filter.

3. MUFFLER: Reduces engine noise output.

See SPARK ARRESTER in the INSTALLATION

section of this manual.

4. “ON/OFF Switch: A two position switch located

on the rear of the engine. In the “ON”(I) position,

the engine ignition circuit is energized and the

engine can be started by pulling the recoil rope

starter. In the “OFF”(O) position, the electronic

ignition is grounded and the engine shuts down.

5. AIR CLEANER: Filters intake air to the carburetor.

See ENGINE MAINTENANCE in the MAINTE-

NANCE section of the engine owner’s manual for

details about the specific type of air cleaner to

use.

6. CHOKE: Provides a richer air/fuel mix-

ture for cold engine starting condi-

tions. See the topic ENGINE OPERA-

TION, below, for details on setting the

choke.

7. RECOIL STARTER: Manual, rope-type starter.

The handle position allows easy starting from

either ground level or pickup-truck level

8. OIL DRAIN PLUG: Permits convenient draining of

engine oil during maintenance. Both sides of the

engine are equipped with an oil drain plug.

9. OIL FILL PLUG: Permits convenient filling of

engine oil during maintenance. Both sides of the

engine are equipped with an oil fill plug.

ENGINE OPERATION

DO NOT RUN THE ENGINE AT EXCESSIVE

SPEEDS. The maximum allowable high idle speed

for the BULLDOG™ 140 is 3750 RPM, no load. Do

NOT adjust the governor screw on the engine.

Severe personal injury and damage to the

machine can result if it is operated at speeds

above the maximum rated speed.

-------------------------------------------------------------

Read and understand all safety instructions included

in the engine manufacturer’s Operating and

Maintenance Instructions manual that is shipped

with the BULLDOG™ 140.

WARNING

4. Pull the cord rapidly.

5. If the engine does not start, open the choke

slightly and pull the starter cord rapidly again.

When the engine starts, gradually open the choke

to the “RUN” position. To open the choke fully

requires an engine warm-up period of several

seconds to several minutes, depending on the

temperature. After starting the engine, first open

the choke (toward RUN) until the engine just

begins to run smoothly. Then open the choke in

small steps, allowing the engine to accept small

changes in speed and load, until the choke is fully

open (in RUN). During engine warm-up the equip-

ment can be operated.

FOR A “HOT” ENGINE:

1. Open the fuel shutoff valve.

2. Place the choke lever in the “RUN”

position. Closing the choke of a hot

engine will flood the carburetor and

prevent starting.

3. Pull slightly on the recoil starter handle until resis-

tance is felt.

4. Pull the cord rapidly.

FOR BEST ENGINE STARTING:

• Always use fresh gasoline and be sure the filter is

clean and properly maintained.

• If you use an alternate fuel tank or supply, be sure

to install an in-line fuel filter.

• Do not pull the recoil starter with the

choke in the “CHOKE” position more

than one time. Repeated pulls on a

choked engine will flood the carburetor.

• If the engine will not start, see the TROU-

BLESHOOTING section of this or the engine

owner’s manual.

B-4

OPERATION

B-4

BEFORE STARTING THE ENGINE

CHECK AND FILL THE ENGINE OIL LEVEL:

1. Place the machine on a level

surface.

2. Open the oil fill plug.

3. Fill (if necessary) until oil flows out the top of the

fill plug hole.

4. Replace the fill plug and tighten securely.

CHECK AND FILL THE ENGINE FUEL TANK:

1. Remove the fuel tank cap.

2. Fill the tank to allow approximately 1/4

inch (5 mm) of tank space for fuel

expansion. DO NOT FILL THE TANK

TO THE POINT OF OVERFLOW.

3. Replace the fuel tank cap and tighten securely.

NOTE: The engine will operate satisfactorily on any

gasoline meant for automotive use. A mini-

mum of 87 octane is recommended. DO NOT

MIX OIL WITH THE GASOLINE.

Use clean, fresh, lead-free gasoline. Leaded gasoline

may be used if lead-free is not available. However,

lead-free gasoline leaves fewer combustion deposits

and gives longer valve life. Purchase gasoline in

quantities that will be used within 30 days, to assure

freshness.

NOTE: We DO NOT recommend using gasoline that

contains alcohol, such as gasohol. However,

if gasoline with alcohol is used, it MUST NOT

contain more than 10% Ethanol and MUST

be removed from the engine during storage.

DO NOT use gasoline containing Methanol.

STARTING THE ENGINE

NOTE: Remove all loads connected to the AC power

receptacles before starting the gasoline

engine. Put the “ON/OFF” Switch in the

“ON”(I) position.

FOR A “COLD” ENGINE:

1. Open the fuel shutoff valve.

2. Place the choke lever in the “CHOKE”

position.

3. Pull slightly on the recoil starter handle until resis-

tance is felt.

BULLDOG™ 140

GENERATOR OPERATION

Be sure that any electrical equipment plugged into

the generator’s AC power receptacles can with-

stand a ±10% voltage and a ±4% frequency varia-

tion. Some electronic devices cannot be powered

by the BULLDOG™ 140. Refer to Table A.2, ELEC-

TRICAL DEVICE USE WITH THE BULLDOG™ 140,

in the INSTALLATION section of this manual.

-------------------------------------------------------------

GENERAL INFORMATION

The BULLDOG™ 140 generator is rated at 4000 con-

tinuous watts (5500 surge watts). It provides both

120 volt and 240 volt power. You can draw up to 20

amps from either side of the 120 volt duplex recepta-

cle, but no more than 33.3 amps from both sides at

once. Up to 16.7 amps can be drawn from the single

240 volt receptacle.

Electrical loads in watts are approximately calculated

by multiplying the voltage rating of the load by the

number of amps it draws. (This information is given

on the load device nameplate.) For example, a

device rated 120 volts, 2 amps will need 240 watts of

power (120 x 2 = 240).

You can use Table B.1, GENERATOR POWER APPLI-

CATIONS, to determine the wattage requirements of

the most common types of loads you can power with

the BULLDOG™ 140. Be sure to read the notes at

the bottom of the table.

TO USE THE BULLDOG™ 140 AS AN AUXILIARY

POWER SUPPLY:

1. Start the gasoline engine. See ENGINE OPERA-

TION in this section of the manual and the engine

owner’s manual.

2. Set the current control dial on the output control

panel to “GENERATOR”. See Figure B.1.

3. Plug the load(s) into the appropriate 120 volt or

240 volt power receptacle.

NOTE: During welding, the maximum generator out-

put for auxiliary loads is 100 watts.

NOTE: You can supply multiple loads as long as the

total load does not exceed 5,500 surge watts

or 4,000 Continuous watts. Be sure to start

the largest loads first.

CAUTION

B-5

OPERATION

B-5

STOPPING THE ENGINE

1. Remove all welding and generator power loads

and let the engine cool by running it for several

minutes.

2. Stop the engine by placing the “ON/OFF” switch

in the “OFF”(O) position.

3. Close the fuel shutoff valve.

Close the fuel valve when the machine is trans-

ported to prevent fuel leakage from the carbure-

tor.

For long periods of storage, turn off the fuel shut-

off valve and let the engine run until there is no

more fuel in the line. Use a fuel additive such as

Sta-Bil to minimize fuel gum deposits.

-------------------------------------------------------------

RUNNING THE ENGINE

The engine is set at the factory to run at high idle

speed when not under load. You should not adjust

this setting yourself.

BREAK-IN PERIOD

The engine will use a greater amount of oil during its

“break-in” period. Check the oil frequently during

break-in. For more details, see the MAINTENANCE

section in the engine owner’s manual.

During break-in, the unit should be subjected to

moderate loads. Before stopping the engine,

remove all loads and allow the engine to cool sev-

eral minutes.

-------------------------------------------------------------

LOW OIL SENSING

This engine has a built in sensor which responds to

low oil level (not pressure). When activated, the syst-

tem will shut the engine down. The engine will not

restart untill sufficient oil is added. Check oil level fre-

quently and add oil as required to the full mark on the

dipstick. (DO NOT OVERFILL)

BULLDOG™ 140

CAUTION

WARNING

TABLE B.1

GENERATOR POWER APPLICATIONS

Suggested Power Applications Running Watts *Start-up Watts

(Continuous) (Surge)

*Air Compressor - 1 HP 2,000 4,000 - 8,000

*Air Compressor - 3/4 HP 1,250 3,100 - 5,000

*Airless Sprayer - 1/3 HP 600 1,500 - 2,400

Chain Saw 1,200

Circular Saw 1,200

Coffee Maker 1,000

*Deep Freezer 500 750 - 2,000

*Electric Motor - 1 HP 1,000 2,500 - 4,000

Electric Range (1 element) 1,500

Electric Skillet 1,250

*Furnace Fan - 1/3 HP 1,200 3,000 - 4,800

Portable Grinder (4 1/2”) 600

Portable Grinder (7”) 2,000

Halogen Work Light 500

Hand Drill - 1/4” 500

Hand Drill - 3/8” 700

1500 Watt Heater 1,500

Hedge Trimmer 450

Light Bulb 100

Reciprocating Saw 900

Radial Arm Saw 2,600

Radio 50

*Refrigerator/Freezer (small) 600 1,500 - 2,400

Slow Cooker 200

*Submersible Pump - 1 HP 1,000 2,500 - 4,000

*Sump Pump 600 1,500 - 2,400

Toaster 1,100

Weed Trimmer 500

Lincoln Wire Feeder/Welder 4,000

B-6

OPERATION

B-6

BULLDOG™ 140

NOTES:

Wattages listed are approximate. Check your equipment for actual wattage.

Equipment with unusually high *START-UP WATTS are listed. For start-up of other tabled equipment that uses a

motor, allow up to 2 times the running watts shown above. For example a 1 HP motor requires approximately

1000 watts of power when running but may require (2.5 X 1000) = 2500 watts or (4.0 X 1000) = 4000 watts to

start.

Multiple loads can be used as long as the total load does not exceed 5,500 surge watts or 4,000 continuous

watts. Be certain to start the largest loads first.

Output rating in watts is equivalent to volt-amperes at unity power factor (resistive load) and is calculated as:

WATTS = VOLTS X AMPS DRAWN. for example a 120 volt device which is rated on its nameplate to draw 2

amps will need (120 VOLTS) X (2 AMPS) = 240 WATTS OF POWER. 1 KW = 1000 WATTS.

La page charge ...

Lincoln Electric Bulldog 140 Manuel utilisateur

Marque: Lincoln Electric

Modèle: Bulldog 140

Catégorie: Système de soudage

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Lincoln Electric Bulldog 140 User manual

Lincoln Electric Bulldog 140 Manuel utilisateur

Lincoln Electric Bulldog 140 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents