Whirlpool WVWA5UC6HN0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WVWA5UC6HN0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

WVWA5UC0HN0

30" AND 36" (76.2 AND 91.4 CM)

WALL‑MOUNT CANOPY RANGE HOOD

Installation Instructions and Use and Care Guide

For questions about features, operation/performance, parts, accessories, or service, call: 1-800-253-1301

or visit our website at www.whirlpool.com.

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca.

HOTTE DE CUISINIÈRE À MONTAGE MURAL

DE30" ET 36" (76,2 ET 91,4 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer le 1-800-807-6777

ou visiter notre site Web à www.whirlpool.ca.

Table of Contents/Table des matières

.....................................2

LIB0098810D/W11134239B

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONL

IMPOR

TANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISA

TION RÉSIDENTIELLE UNIQUEMENT

TABLE OF CONTENTS TABLE DES MATIÈRES

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS ................................................. 4

Tools and Parts .............................................................................4

Location Requirements ................................................................4

Venting Requirements ..................................................................5

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS ................................................... 7

Prepare Location ..........................................................................7

Install Range Hood ....................................................................... 8

Connect Vent System ..................................................................8

Make Electrical Connection .........................................................9

Install Vent Covers ........................................................................9

Complete Installation .................................................................10

RANGE HOOD USE ......................................................................10

Range Hood Controls ................................................................10

RANGE HOOD CARE ...................................................................11

Cleaning .....................................................................................11

WIRING DIAGRAM .......................................................................12

ASSISTANCE OR SERVICE .........................................................13

In the U.S.A. ...............................................................................13

In Canada ...................................................................................13

Accessories ................................................................................13

WARRANTY ..................................................................................14

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................15

EXIGENCES D’INSTALLATION ...................................................17

Outils et pièces ...........................................................................17

Exigences d’emplacement .........................................................17

Exigences concernant l’évacuation ...........................................18

Spéciﬁcations électriques ..........................................................20

INSTRUCTIONS D’INSTALLATION .............................................20

Préparation de l’emplacement ...................................................20

Installation de la hotte ................................................................21

Raccordement du circuit d’évacuation ...................................... 22

Raccordement électrique ...........................................................22

Installation des cache-conduits .................................................23

Achever l’installation ..................................................................23

UTILISATION DE LA HOTTE .......................................................24

Commandes de la hotte de cuisinière .......................................24

ENTRETIEN DE LA HOTTE .........................................................25

Nettoyage ...................................................................................25

SCHÉMA DE CÂBLAGE ...............................................................26

ASSISTANCE OU SERVICE .........................................................27

Au Canada ..................................................................................27

Accessoires ................................................................................27

GARANTIE .....................................................................................27

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here.

Tools Needed

■ Level

■ Drill with 1

" (3.2 cm), 1/8" (3.2 mm),

and 5/16" (7.9 mm) drill bits

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

Parts Needed

■ Home power supply cable

■ 1/2" (12.7 mm) UL Listed or CSA approved strain relief

■ Three UL Listed wire connectors

For Vented Installations, You Will Also Need:

■ One wall or roof cap

■ Metal vent system

For Non-Vented (Recirculating) Installations,

You Will Also Need:

■ Recirculation Kit - See the “Assistance or Service” section to

order.

■ 6" (15.2 cm) diameter round metal vent duct -

length required is determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

■ Hood canopy assembly with blower, lights ,and canopy glass

already installed

■ Vent transition with back draft dampers installed

■ Metal grease ﬁlter

■ Vent cover support bracket

■ Mounting template

■ Two piece vent cover

■ Four 4.2 x 8 mm screws

■ Six 5 x 45 mm mounting screws

■ Two 3.5 x 9.5 mm mounting screws

■ Two 8 x 40 mm wall anchors

■ Four 10 x 60 mm wall anchors

■ Four 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)

■ T10 Torx

®†

adapter

■ T20

®†

Torx

adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualiﬁed technician install the range hood. It is the

installer’s responsibility to comply with installation clearances

speciﬁed on the model/serial/rating plate. The model/serial/

rating plate is located behind the left ﬁlter on the rear wall

of the vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

This range hood is recommended for use with cooktops with

a maximum total rating of 65,000 BTUs or less.

Grounded electrical outlet is required. See the “Electrical

Requirements” section.

The canopy hood is factory set for venting through the roof

or wall. For non-vented (recirculating) installation see “For

non-vented (recirculating) installation only” in the “Connect

Vent System” section. Recirculation Kit is available from your

dealer or an authorized parts distributor. See the “Assistance or

Service” section to order.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD, Part 280)

or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A,

or latest edition, or with local codes.

Product Dimensions

20"

(50.8 cm)

30" (76.2 cm) or

36" (91.4 cm)

13³⁄₁₆"

(33.5 cm)

⁷⁄₈

(27.6 cm)

†

TORX

and T20

are registered trademarks of Acument Intellectual Properties, LLC.

* For non-vented (recirculating) installations

** For vented installations

Cabinet Dimensions

* For non-vented (recirculating) installations

IMPORTANT:

Minimum distance “X”: 24" (61 cm)

from electric cooking surface

Minimum distance “X”: 27" (68.6 cm)

from gas cooking surface

Suggested maximum distance “X”: 36" (91.4 cm)

The chimneys can be adjusted for different ceiling heights.

See the following chart.

Vented Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 4" (2.23 m) 9' 5" (2.87 m)

Gas cooking

surface

7' 7" (2.31 m) 9' 5" (2.87 m)

Non-Vented (Recirculating) Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 4" (2.23 m) 9' 9" (2.97 m)

Gas cooking

surface

7' 7" (2.31 m) 9' 9" (2.97 m)

NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or sofﬁt heights depending on the

distance “X” between the bottom of the range hood and the

cooking surface. For higher ceilings, a Chimney Extension Kit is

available from your dealer or an authorized parts distributor. The

chimney extension replaces the upper chimney shipped with the

range hood. See the “Assistance or Service” section to order.

Venting Requirements

(vented models only)

■ Vent system must terminate to the outdoors except

for non-vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use 4" (10.2 cm) laundry-type wall cap.

■ Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■ The length of vent system and number of elbows should

be kept to a minimum to provide efﬁcient performance.

For the Most Efﬁcient and Quiet Operation:

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight

vent between the elbows if more than one elbow is used.

■ Do not install two elbows together.

■ Use clamps to seal all joints in the vent system.

■ The vent system must have a damper. If the roof

or wall cap has a damper, do not use the damper

supplied with the range hood.

■ Use caulking to seal exterior wall or roof opening

around the cap.

■ The size of the vent should be uniform.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air ﬂow and a thermal break should be installed

to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the

thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

³⁄₁₆" (43.7 cm)

**27¹⁄₈" (68.9 cm) min.

**41¹⁄₈

" (104.5 cm) max.

*27¹⁄₈" (68.9 cm) min.

*45¹⁄₂" (115.6 cm) max.

10" (25.4 cm) min.

13" (33.0 cm) max.

9¹⁄₂" (24.1 cm)

2" (5.1 cm) min.

9" (22.9 cm) min.*

Centerline

Side

cabinet

Side

cabinet

Vent and po

wer

supply cable

entry location

20" (50.8 cm)* min.

30" (76.2 cm) or

36" (91.4 cm)

“X”

bottom of

canopy

to cooking

surface

10" (25.4 cm) min.

13" (33.0 cm) max.

Cooking surface

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than speciﬁed CFM of

air movement. The speciﬁed CFM varies from locale to locale.

Consult your HVAC professional for speciﬁc requirements in

your area.

Venting Methods

This canopy hood is factory set for venting through

the roof or wall.

A 6" (15.2 cm) round vent system is needed for installation

(not included). The hood exhaust opening is 6" (15.2 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent

creates back pressure and air turbulence that greatly

reduce performance.

Vent system can terminate either through the roof or wall.

To vent through a wall, a 90° elbow is needed.

Rear Discharge

A 90° elbow may be installed immediately above the hood.

For Non-Vented (Recirculating) Installations

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, ﬁtting a charcoal ﬁlter and the deﬂector. Fumes and

vapors are recycled through the top grille.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft (0.8 m)

90° elbow 5 ft (1.5 m)

Maximum equivalent vent length is 35 ft (10.7 m).

Example Vent System

The following example falls within the maximum

recommended vent length of 35 ft (10.7 m).

1 – 90° elbow = 5 ft (1.5 m)

1 – wall cap = 0 ft (0 m)

8 ft (2.4 m) straight = 8 ft (2.4 m)

Length of system = 13 ft (3.9 m)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA

70 (latest edition), or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition)

and all local codes and ordinances.

If codes permit and a separate ground wire is used,

it is recommended that a qualiﬁed electrician determine

that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical

circuit is required.

■ If the house has aluminum wiring, follow the

procedure below:

1. Connect a section of solid copper wire to the

pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL Listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as speciﬁed on the model/serial/rating plate.

The model/serial/rating plate is located behind the left ﬁlter

on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1

and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

Non-Vented

(Recirculating)

Wall Venting

Roof Venting

A. Deﬂector

B. 6" (15.2 cm)

round vent

A. Wall cap

B. 6" (15.2 cm)

round vent

A. Roof cap

B. 6" (15.2 cm)

round vent

90 elbo

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed

before hood is installed.

■ Before making cutouts, make sure there is proper

clearance within the ceiling or wall for exhaust vent.

■ Check your ceiling height and the hood height

maximum before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall,

or non-vented.

3. Select a ﬂat surface for assembling the range hood.

Place covering over that surface.

4. Using two or more people, lift range hood onto

covered surface.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where

the canopy hood will be installed.

2. Select a mounting height between a minimum of 24" (61 cm)

for an electric cooking surface, a minimum of 27" (68.6 cm)

for a gas cooking surface, and a suggested maximum of 36"

(91.4 cm) above the range to the bottom of the hood. Mark a

reference line on the wall.

3. Tape template in place, aligning the template centerline

and bottom of template with hood bottom line and with

the centerline marked on the wall.

4. Mark centers of the fastener locations through the template

to the wall.

IMPORTANT: All canopy mounting screws must be installed

into wood where possible. If there is no wood to screw into,

additional wall framing supports may be required, or use

the (4) 10 x 60 mm wall anchors and 5.4 x 75 mm screws.

Remove the template.

5. For wood, drill 3/16" (4.8 mm) pilot holes at all locations

where screws are being installed into wood.

For wall anchors, drill 7/16" (10 mm) holes at all locations

where wall anchors are being used.

6. For wood, install (2) 5 x 45 mm mounting screws. Leave

a 1/4" (6.4 mm) gap between the wall and the back of the

screw head to slide range hood into place.

For wall anchors, install the 10 x 60 mm wall anchors

and install the 5.4 x 75 mm screws into the wall anchors.

Tighten until the wall anchors are secure. Back the screws

out 1/4" (6.4 mm).

Vent Cover Bracket Installation

7. Attach vent cover bracket to wall ﬂush to the ceiling using (2)

5 x 45 mm screws. Use the optional wall anchors if needed.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the

vent system. Install the vent system before installing the

hood. See “Venting Requirements” section.

2. Determine the required height for the home power supply

cable and drill a 1

" (3.2 cm) hole at this location.

3. Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough 1/2" (12.7 mm) conduit

and wires from the fused disconnect (or circuit breaker) box

to make the connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

Vertical Centerline

LLAW RAER

ETALPMET GNITNUOM

EGDE MOTTOB NGILA

ENIL LICNEP HTIW

MOTTOB GNITACIDNI

DOOH EHT FO

thgieH noitallatsnI

TROPPUS LLAW RAER RO SDUTS HGUORHT SELOH TOLIP "61/3 )OWT( 2 LLIRD

eniL latnoziroH

A. Centerline

B. Fastener locations

C. Mounting height reference (hood bottom line)

¹⁄₄

(6.4 mm)

A. Ceiling

B. Wall

C. Centerline

Install In-Line Smart Kit—Optional

NOTE: Your range hood can work with either an internal or an

inline (external) blower motor system. An optional In-Line Smart

Kit (purchased separately) allows the blower motor that comes

with this range hood to be installed in a location other than

inside the range hood cavity.

CAUTION: To reduce the risk of ﬁre and electric shock, install

this range hood only with the In-Line Smart Kit manufactured

by Whirlpool. See the “Assistance or Service” section to order.

For installation see the In-Line Smart Kit installation instructions.

See the “Assistance or Service” section to order.

Install Range Hood

1. Using two or more people, hang range hood on two

mounting screws through the mounting slots on back of

hood.

2. Remove the grease ﬁlter. See “Range Hood Care” section.

3. Level the range hood and tighten upper mounting screws.

4. Install (2) 5 x 45 mm lower mounting screws and tighten.

Use the optional wall anchors if needed.

Connect Vent System

1. Install transition on top of hood (if removed for shipping)

with (2) 3.5 x 9.5 mm sheet metal screws.

For vented installations only:

1. Fit vent system over the exhaust outlet.

2. Seal connection with clamps.

3. Check that back draft dampers work properly.

For non-vented (recirculating) installation only:

1. Assemble the air deﬂector with the duct cover bracket

using (4) 4.2 x 8 mm screws.

2. Measure from the bottom of the air deﬂector to the bottom

of the hood outlet.

3. Cut the duct to the measured size “X.”

4. Remove the air deﬂector.

5. Slide the duct onto the bottom of the air deﬂector.

6. Place the assembled air deﬂector and duct over

the exhaust outlet from the hood.

7. Reassemble the air deﬂector to the duct cover bracket

with the four assembly screws.

8. Seal connections with vent clamps.

A. Mounting screws

B. Mounting slots

C. Lower mounting screws

A. Vent transition

B. 3.5 x 9.5 mm screw

A. Assembly screws

B. Air deﬂector

C. Duct cover bracket

A. Air deﬂector

B. Vent clamp

C. X = length to cut vent duct

D. Vent duct

E. Exhaust outlet

Make Electrical Connection

1. Disconnect power.

2. Remove terminal box cover.

3. Remove the knockout in the terminal box and install

a UL Listed or CSA approved 1/2" (12.7 mm) strain relief.

4. Run home power supply cable through strain relief

into terminal box.

5. Use UL Listed wire connectors and connect

black wires (C) together.

6. Use UL Listed wire connectors and connect

white wires (E) together.

7. Connect green (or bare) ground wire from home power

supply to yellow-green ground wire (F) in terminal box

using UL Listed wire connectors.

8. Tighten strain relief screw.

9. Install terminal box cover.

10. Check that all light bulbs are secure in their sockets.

11. Reconnect power.

Optional Power Cord Kit Installations

For optional power cord kit installations, follow the instructions

supplied with the power cord kit. See the “Assistance or

Service” section for information on ordering.

NOTE: Use only with range hood cord connection kits that have

been investigated and found acceptable for use with this model

range hood.

Install Vent Covers

1. When using both upper and lower vent covers, push lower

cover down onto hood and lift upper cover to ceiling and

install with two 4.2 x 8 mm screws.

NOTE: For vented installations, the upper vent cover

may be reversed to hide slots.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

A. Knockout

B. Terminal box

C. Terminal box cover

A. Home power supply cable

B. UL Listed or CSA

approved strain relief

C. Black wires

D. UL Listed wire connectors

E. White wires

F. Green (or bare) and

yellow-green ground wires

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

A. Bracket

B. 4.2 x 8 mm screws

C. Vent cover

2. Secure the bottom of the duct with (2) 4.2 x 8 mm screws.

Complete Installation

1. For non-vented (recirculating) installations only, install

charcoal ﬁlters over metal grease ﬁlter. See the “Range

Hood Care” section.

2. Install metal ﬁlters. See the “Range Hood Care” section.

3. Check the operation of the range hood blower and light.

See the “Range Hood Use” section.

NOTE: To get the most efﬁcient use from your new range hood,

read the “Range Hood Use” section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking

vapors and odors from the cooktop area. For best results,

start the hood before cooking and allow it to operate several

minutes after the cooking is complete to clear all smoke and

odors from the kitchen.

The hood controls are located on the front side of the canopy.

Range Hood Controls

Operating the LED task light

The On/Off light button controls both lights. Press once

for on and again for off.

Operating the blower

The Blower Speed buttons turn the blower on and control the

blower speed and sound level for quiet operation. The speed

can be changed anytime during fan operation by pressing the

desired Blower Speed button.

The Blower Off button turns the blower off.

Operating the Ambient Lighting

The switch controls the ambient lighting.

1. Press to the left to turn Auto On.

2. Press to the right to turn Ambient Lighting On.

3. Press to the center to turn Ambient Lighting or Auto Off.

NOTE: When the Ambient Lighting is placed in the Auto setting,

a sensor will automatically sense if it is dark in the area around

the range hood. The Ambient Lighting will turn on and stay on

until it senses there is enough light in the area around the range

hood, or the Ambient Lighting switch is placed in the on or

off position.

A. Louver holes (non-vented

[recirculating] installations only)

B. Duct cover

C. Control panel

D. Light switch (ambient lighting)

E. Glass canopy

F. Perimetric cover

G. LED lights

H. Metal grease ﬁlters (located

behind the perimetric cover)

A. Blower speed maximum button

B. Blower speed medium button

C. Blower speed minimum button

D. Blower off button

E. On/Off LED task light button

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease ﬁlters frequently

according to the following instructions. Replace grease

ﬁlters before operating hood.

Exterior Surfaces

To avoid damage to the exterior surface, do not use steel wool

or soap-ﬁlled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

■ Liquid detergent soap and water, or all-purpose cleanser.

■ Wipe with damp soft cloth or nonabrasive sponge,

and then rinse with clean water and wipe dry.

Metal Grease Filter

1. Open the stainless steel panel. Grasp panel at the left

corners and pull down to disengage the two catch pins

from the spring catches. The panel is attached at the

right and will rotate down.

2. Remove the ﬁlter by pulling the spring release handle

and then pulling down the ﬁlter.

3. Wash metal ﬁlter as needed in dishwasher or hot

detergent solution.

4. Reinstall the ﬁlter by making sure the spring release handles

are toward the front. Insert aluminum ﬁlter into upper track.

5. Push in spring release handle.

6. Push up on metal ﬁlter and release handle to latch into place.

Non-Vented (recirculating) Installation Filters

The charcoal ﬁlter is not washable. It should last up to

6 months with normal use. Replace with Charcoal Filter Kit. See

the “Assistance or Service” section for information on ordering.

To replace charcoal ﬁlter:

1. Remove metal grease ﬁlter from range hood.

See “Metal Grease Filter” in this section.

2. Bend spring clips away from metal grease ﬁlter.

3. Place charcoal ﬁlter into top side of metal ﬁlter.

4. Bend spring clips back into place to secure the

charcoal ﬁlter to the metal ﬁlter.

5. Replace metal grease ﬁlter. See “Metal Grease Filter”

in this section.

Replacing an LED Lamp

The LED lights are replaceable by a service technician only.

See the “Warranty” section for service contact information.

A. Spring release handle

WIRING DIAGRAM

SE131C

Push Button Switch

Operation

Function

Position

Off

Lamps

Low Speed

Med Speed

High Speed

No Connection

Blue - Ye llow

(M - La)

Brown - White

(L - 1)

Brown - Red

(L - 2)

Brown - Black

(L - 3)

Motor Specifications

Power Supply

Frequency

Power Absorption

Blue - Black

Blue - Gray

Blue - Red

Blue - White

120 VAC

60 HZ

240 W

28.8

30.3

37.7

45.1

73ºF (23ºC)

Room Te mp.

Light

Sensor

Tu rns on at 10 LUX

Tu rns off at 50 LUX

Output

Input

Driver

Output: 700mA (2-15 VDC)

Input: 120 VAC

Strip LED

Ambient Light Switch

Function

Off

Auto

Position

Position 3

Position 2

Position 1

Input: 120 VAC

Output: 700mA (2-15 VDC)

Driver

YL/GN

21L3MLa

POS 1

POS 2

POS 3

YL/GN

LED

YL/GN

ASSISTANCE OR SERVICE

If you need service

Please refer to the warranty page in this manual.

If you need replacement parts

If you need to order replacement parts, we recommend that

you use only factory speciﬁed parts. Factory speciﬁed parts

will ﬁt right and work right because they are made with the

same precision used to build every new appliance.

To locate factory speciﬁed replacement parts in your area,

call the following customer assistance telephone number

or your nearest designated service center.

In the U.S.A.

Call the Whirlpool Customer eXperience Center toll free:

1-800-253-1301 or visit our website at www.whirlpool.com.

Our consultants provide assistance with:

■ Scheduling of service. Whirlpool designated service

technicians are trained to fulﬁll the product warranty and

provide after-warranty service anywhere in the United States.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking,

hearing impaired, limited vision, etc.).

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada Customer eXperience Centre toll free:

1-800-807-6777, or visit our website at www.whirlpool.ca.

Our Consultants Provide Assistance With:

■ Scheduling of Service. Whirlpool designated service

technicians are trained to fulﬁll the product warranty

and provide after-warranty service anywhere in Canada.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local dealers.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For Further Assistance

If you need further assistance, you can write to Whirlpool

Canada with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Recirculation Kit

(for non-vented installations only)

Order Part Number W10294733

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10412939

Chimney Extension Kit (Stainless Steel)

Order Part Number EXTKIT10ES

Chimney Extension Kit (Sunset Bronze)

Order Part Number EXTKIT10HN

Power Cord Kit

Order Part Number W10613691

In-Line Smart Kit

Order part Number W10692945

12/15

WHIRLPOOL

CORPORATION

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address, and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions

can be addressed without service. Please take a few minutes to review the Troubleshooting or Problem Solver

section of the Use and Care Guide.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and Canada, direct all requests

for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according

to instructions attached to or furnished

with the product, Whirlpool Corporation

or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for Factory

Speciﬁed Replacement Parts and repair

labor to correct defects in materials or

workmanship that existed when this

major appliance was purchased, or at

its sole discretion replace the product.

In the event of product replacement,

your appliance will be warranted for

the remaining term of the original unit’s

warranty period.

YOUR SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT

REPAIR AS PROVIDED HEREIN.

Service must be provided by a

Whirlpool designated service company.

This limited warranty is valid only

in the United States or Canada and

applies only when the major appliance

is used in the country in which it was

purchased. This limited warranty is

effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user,

operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in accordance

with electrical or plumbing codes, or correction of household electrical or plumbing (i.e. house

wiring, fuses, or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters, preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.

6. Conversion of your product from natural gas or L.P. gas or reversal of appliance doors.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God, or use with products not

approved by Whirlpool.

8. Repairs to parts or systems to correct product damage or defects caused by unauthorized

service, alteration, or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to appliance ﬁnishes

unless such damage results from defects in materials and workmanship and is reported to

Whirlpool within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive environments,

including but not limited to, high salt concentrations, high moisture or humidity, or exposure

to chemicals.

11. Food or medicine loss due to product failure.

12. Pick-up or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized Whirlpool

servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e. trim, decorative

panels, ﬂooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing,

removal, or replacement of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered, or not

easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne

by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not

allow limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty gives

you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the

exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives

you speciﬁc legal rights, and you also may have other rights that vary from state to state or province to province.

W11134239B 07/17

12/15

GARANTIE LIMITÉE

DES GROS APPAREILS

MÉNAGERS WHIRLPOOL

CORPORATION

ATTACHEZ ICI VOTRE REÇU DE VENTE. UNE PREUVE D’ACHAT EST

OBLIGATOIRE POUR OBTENIR L’APPLICATION DE LA GARANTIE.

Lorsque vous appelez le centre d’eXpérience de la clientèle, veuillez garder

à disposition les renseignements suivants :

■ Nom, adresse et numéro de téléphone

■ Numéros de modèle et de série

■ Une description claire et détaillée du problème rencontré

■ Une preuve d’achat incluant le nom et l’adresse du marchand ou du détaillant

SI VOUS AVEZ BESOIN DE SERVICE :

1. Avant de nous contacter pour obtenir un dépannage, veuillez déterminer si des réparations sont nécessaires pour votre produit. Certains

problèmes peuvent être résolus sans intervention de dépannage. Prenez quelques minutes pour parcourir la section Dépannage ou

Résolution des problèmes du guide d’utilisation et d’entretien.

2. Tout service sous garantie doit être effectué exclusivement par nos fournisseurs de dépannage autorisés Whirlpool.

Aux É.-U. et au Canada, dirigez toutes vos demandes de service sous garantie au :

Centre d’eXpérience de la clientèle Whirlpool

Aux É.-U., composer le 1 800 253 -1301. Au Canada, composer le 1 800 807 -6777.

Si vous résidez à l’extérieur du Canada ou des 50 États des États-Unis, contactez votre marchand Whirlpool autorisé pour déterminer

si une autre garantie s’applique.

GARANTIE LIMITÉE DE UN AN

CE QUI EST COUVERT CE QUI N’EST PAS COUVERT

Pendant un an à compter de la date

d’achat, lorsque ce gros appareil

ménager est installé, utilisé et entretenu

conformément aux instructions jointes

à ou fournies avec le produit, Whirlpool

Corporation ou Whirlpool Canada,

LP (ci-après désignées “Whirlpool”)

décidera à sa seule discrétion de

remplacer le produit ou de couvrir le

coût des pièces spéciﬁées par l’usine

et de la main-d’œuvre nécessaires pour

corriger les vices de matériaux ou de

fabrication qui existaient déjà lorsque

ce gros appareil ménager a été acheté.

S’il est remplacé, l’appareil sera couvert

pour la période restant à courir de la

garantie limitée d’un an du produit

d’origine.

LE SEUL ET EXCLUSIF RECOURS

DU CLIENT DANS LE CADRE DE

LA PRÉSENTE GARANTIE LIMITÉE

CONSISTE EN LA RÉPARATION

PRÉVUE PAR LA PRÉSENTE. Le service

doit être fourni par une compagnie de

service désignée par Whirlpool. Cette

garantie limitée est valide uniquement

aux États-Unis ou au Canada et

s’applique exclusivement lorsque le gros

appareil ménager est utilisé dans le pays

où il a été acheté. La présente garantie

limitée est valable à compter de la date

d’achat initial par le consommateur.

Une preuve de la date d’achat initial est

exigée pour obtenir un dépannage dans

le cadre de la présente garantie limitée.

1. Usage commercial, non résidentiel ou par plusieurs familles, ou non-respect des instructions de

l’utilisateur, de l’opérateur ou des instructions d’installation.

2. Visite d’instruction à domicile pour montrer à l’utilisateur comment utiliser l’appareil.

3. Visites de service pour rectiﬁer une installation ou un entretien fautifs du produit, une installation non

conforme aux codes d’électricité ou de plomberie, ou la rectiﬁcation de l’installation électrique ou de

la plomberie du domicile (ex : câblage électrique, fusibles ou tuyaux d’arrivée d’eau du domicile).

4. Pièces consomptibles (ex : ampoules, piles, ﬁltres à air ou à eau, solutions de conservation, etc.).

5. Défauts ou dommage résultant de l’utilisation de pièces ou accessoires Whirlpool non authentiques.

6. Conversion de votre produit du gaz naturel ou du gaz de pétrole liquéﬁé, ou inversion des portes de

l’appareil.

7. Dommages causés par : accident, mésusage, abus, incendie, inondations, catastrophe naturelle

ou l’utilisation de produits non approuvés par Whirlpool.

8. Réparations aux pièces ou systèmes dans le but de rectiﬁer un dommage ou des défauts résultant

d’une réparation, altération ou modiﬁcation non autorisée faite à l’appareil.

9. Défauts d’apparence, notamment les éraﬂures, traces de choc, ﬁssures ou tout autre dommage

subi par le ﬁni de l’appareil ménager, à moins que ces dommages ne résultent de vices de matériaux

ou de fabrication et ne soient signalés à Whirlpool dans les 30 jours suivant la date d’achat.

10. Décoloration, rouille ou oxydation des surfaces résultant d’environnements caustiques ou corrosifs

incluant des concentrations élevées de sel, un haut degré d’humidité ou une exposition à des

produits chimiques (exemples non exhaustifs).

11. Perte d’aliments ou de médicaments due à la défaillance du produit.

12. Enlèvement ou livraison. Ce produit est conçu pour être réparé à l’intérieur du domicile.

13. Frais de déplacement et de transport pour le dépannage/la réparation dans une région éloignée

où une compagnie de service Whirlpool autorisée n’est pas disponible.

14. Retrait ou réinstallation d’appareils inaccessibles ou de dispositifs préinstallés (ex : garnitures,

panneaux décoratifs, plancher, meubles, îlots de cuisine, plans de travail, panneaux de gypse, etc.)

qui entravent le dépannage, le retrait ou le remplacement du produit.

15. Service et pièces pour des appareils dont les numéros de série et de modèle originaux ont été

enlevés, modiﬁés ou ne peuvent pas être facilement identiﬁés.

Le coût d’une réparation ou d’un remplacement dans le cadre de ces circonstances exclues est

à la charge du client.

CLAUSE D’EXONÉRATION DE RESPONSABILITÉ AU TITRE DES GARANTIES IMPLICITES

LES GARANTIES IMPLICITES, Y COMPRIS LES GARANTIES APPLICABLES DE QUALITÉ MARCHANDE OU D’APTITUDE À UN USAGE

PARTICULIER, SONT LIMITÉES À UN AN OU À LA PLUS COURTE PÉRIODE AUTORISÉE PAR LA LOI. Certains États et provinces ne

permettent pas de limitation sur la durée des garanties implicites de qualité marchande ou d’aptitude à un usage particulier, de sorte que la

limitation ci-dessus peut ne pas être applicable dans votre cas. Cette garantie vous confère des droits juridiques spéciﬁques et vous pouvez

également jouir d’autres droits qui peuvent varier d’une juridiction à l’autre.

EXONÉRATION DE RESPONSABILITÉ DANS LES DOMAINES NON COUVERTS PAR LA GARANTIE

Whirlpool décline toute responsabilité au titre de la qualité, de la durabilité ou en cas de dépannage ou de réparation nécessaire sur ce gros

appareil ménager autre que les responsabilités énoncées dans la présente garantie. Si vous souhaitez une garantie plus étendue ou plus

complète que la garantie limitée fournie avec ce gros appareil ménager, adressez-vous à Whirlpool ou à votre détaillant pour obtenir les

modalités d’achat d’une garantie étendue.

LIMITATION DES RECOURS; EXCLUSION DES DOMMAGES FORTUITS OU INDIRECTS

LE SEUL ET EXCLUSIF RECOURS DU CLIENT DANS LE CADRE DE LA PRÉSENTE GARANTIE LIMITÉE CONSISTE EN LA RÉPARATION

PRÉVUE PAR LA PRÉSENTE. WHIRLPOOL N’ASSUME AUCUNE RESPONSABILITÉ POUR LES DOMMAGES FORTUITS OU INDIRECTS.

Certains États et certaines provinces ne permettent pas l’exclusion ou la limitation des dommages fortuits ou indirects de sorte que ces

limitations et exclusions peuvent ne pas être applicables dans votre cas. Cette garantie vous confère des droits juridiques spéciﬁques et

vous pouvez également jouir d’autres droits qui peuvent varier d’une juridiction à l’autre.

Whirlpool WVWA5UC6HN0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WVWA5UC6HN0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

WVWA5UC0HN0

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WVWA5UC6HN0 Owner's manual

Whirlpool WVWA5UC6HN0 Le manuel du propriétaire

Ce manuel convient également à

Whirlpool WVWA5UC6HN0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents