Quick start guide
Pixavi Phone
Pixavi Thermal
Pixavi Cam
Congratulations on your Pixavi intrinsically safe device.
All you need to get started with Pixavi Phone, Pixavi Cam and
Pixavi Thermal can be found in this quick guide. If you need
further assistance, try the AndroidTM help function, or visit:
www.bartecmobility.com/support-portal
Pixavi Phone ¹
Intrinsically safe smartphone
Pixavi Thermal (²)
Intrinsically safe smartphone with FLIRTM thermal camera
Pixavi Cam (³)
Intrinsicallty safe camera
Introduction Your device
1: 5.5” OLED
2: Power button
3: Volume button (-/+)
4: Programmable button
5: Proximity/Ambient light sensor and status LED
6: Front Camera
7: Earpiece speaker
8: Lanyard mounting slot
9: Magnetic USB connector
10: Microphone
2
4
5
6 7
8
910
3
1
1: Loudspeaker
2: Thermal camera (²)
3: Main camera
4: Flash
5: Microphone
6: Dual SIM/SD tray (¹, ²) or SD tray (³) (below battery pack)
7: Battery pack
8: Battery pack torx T10 fasteners
9: NFC
1
2
45
6
7
9
8
3
1: Insert the SIM and/or SD card according to the
SIM/SD-card instructions (separate sheet)
2: Press and hold the Power button to power on the device
Insert the magnetic charger cable in the USB/Charging port
at the bottom of the device. Make sure the orientation of the
cable is as illustrated below.
Do not use any force when inserting the magnetic charging/USB
cable
Charge the device in the non-hazardous area only
For charging the device, use only Bartec approved chargers and
cables. More info in the “Conditions For Use” sections
Getting started
Charging
(¹) Pixavi Phone
(²) Pixavi Thermal
(³) Pixavi Cam
If the device becomes unresponsive or does not boot
successfully, try performing a soft reset. This is done by
pressing and holding the power button down for 10 seconds.
FAQs and technical support can be found here:
www.bartecmobility.com/support-portal
Troubleshooting and Support
Product marking
The programmable button can be configured to launch an
applications or action on single tap, double tap and long
press.
It’s comes preconfigured but can be changed based on your
preferences. Go to Setting -> Programmable Button.
Other options:
Push-to-talk (PTT): Press and hold to talk.
Single tap, duble tap and press and hold will be disabled
when PTT is activated.
SOS-message: Tap the button fast 5 times to send a SOS
message to one or multiple contacts.
Programmable button
WARNING: Do not charge or open battery in hazardous areas!
ATTENTION: Ne pas charger ia batterie dans la zone a risque d'explosion
Pixavi
ThermalClass I, II, III, Division 1
Groups A, B, C, D, E, F, G
Class I, Zone 0, AEX ia IIC T4 Ga,
Ex ia IIC T4 Ga
Zone 20, AEX ia IIICT135˚C Da ;
Ex ia IIICT135˚C Da
CSA 20 ATEX
x xxx X
II 1G Ex ia IICT4 Ga
II 1D Ex ia IIICT 135˚C Da I P6x
I M1 Ex ia I Ma
IECEx CSA 20.xxxxX
S/N X8KYYPTXXXXXX
Type:
17-S13*-1***/********
BARTEC GmbH www.bartec.com
97980 Bad Mergentheim / Germany
Assembled in Norway
Only use battery type: 17-S1Z0-0001
Utiliser uniquement la batterie type: 17-S1Z0-0001
Read user manuel before use
Lire le manuel d'utilisation avent utilisation
FCC ID: XXXXXXXXXXXXXXXX, IC ID:
XXXXXXXXXXXXXXXX
Cell made in China, Assembled in Norway
Pixavi Battery
Mfr: BARTEC GmbH
97980 Bad Mergentheim, DE
Type: 17-S1Z0-0001
Battery info 3.8 V , 3200 mAh , 12.16 Wh
Limited Charge Voltage (4.35 V) Class I, II, III, Division 1
Groups A, B, C, D, E, F, G
Class I, Zone 0, AEX ia IIC T4 Ga,
Ex ia IIC T4 Ga
Zone 20, AEX ia IIICT135˚C Da ;
Ex ia IIICT135˚C Da
CSA 20 ATEX x xxx X
II 1G Ex ia IICT4 Ga
II 1D Ex ia IIICT 135˚C Da I P6x
I M1 Ex ia I Ma
IECEx CSA 20.xxxxX
0044
0044
S/N:
X8K(YY)PB(xxxxxx)
QR-
code
The device is compliant with the EN9650-1 standard.
However, third party music players can exceed the
recommended audio levels, and as such should be used with
caution as prolonged listening to sound at high volumes can
cause permanent damage.
Ex ib parameter
Uo
Io
Po
Co
Lo
USB Interface
X.X V
X.X A
X.X W
-
-
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Ce produit répond aux exigences de la section 15 de la
réglementation FCC. Son fonctionnement est soumis aux
deux conditions suivantes: (1) cet appareil ne doit pas causer
d’interférences nuisibles et (2) cet appareil doit accepter
toute interférence reçue, y compris les interférences qui
peuvent provoquer un fonctionnement indésirable.
Audio Levels
Special Conditions For Safe Use
FCC/IC
The Pixavi Phone, Pixavi Thermal and Pixavi Cam is a radio
transmitter and receiver. It is designed and manufactured
not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government, Industry Canada
of the Canadian Government (IC), and recommended by The
Council of the European Union. The exposure standard for
wireless devices employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The SAR limit set by
the FCC/IC is 1.6W/kg. The SAR limit recommended by The
Council of the European Union is 2.0W/kg. Tests for SAR are
conducted using standard operating positions specified by
the FCC/IC with the device transmitting at its highest certi-
fied power level in all tested frequency bands.
For body worn operation, the Pixavi Phone, Pixavi Thermal
and Pixavi Cam devices has been tested and meets the FCC/
IC exposure guidelines when used with an accessory that
contains no metal and that positions the device a minimum
of 10 mm from the body. Such a device can i.e. be BARTEC
PIXAVI wrist cradle or BARTEC PIXAVI belt clip.
The highest SAR value measured for the Pixavi Phone, Pixavi
Thermal and Pixavi Cam is:
Head SAR: (W/kg)
Body SAR: (W/kg)
Text must be approved and tested during FCC cert
Text must be approved during FCC cert
Specific Absorption Rate Data
0.571
0.148
FCC
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This Pixavi Cam meets the government's requirements for exposure to radio
waves. The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific studies.
Thestandards include a substantial safety margin designed to assure the safety of all
persons regardless of age or health.
IC
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement
The ambient temperature range of the device is -20°C to +
60°C. The device shall be protected from contamination by
liquid and dust; this is normally achieved by the operator
carrying the device on their person. The USB port may be
used for charging the equipment when in the non-hazardous
area only.
For charging the device, use only Bartec approved chargers:
Charger with EU plug: G7-S0Z0-0001
Charger with UK plug: G7-S0Z0-0002
Charger with US plug: G7-S0Z0-0003
Charger with AU plug: G7-S0Z0-0004
Charging dock: G7-S0Z0-0007
Vehicle charging dock: G7-S0Z0-0008
For connection to computers and car chargers, use only
Bartec approved charging cable:
USB Safe Box cable G7-S0Z0-0006
Conditions For Use (ATEX & IECEx)
The ambient temperature range of the device is -20°C to +
60°C. The device shall be protected from contamination by
liquid and dust; this is normally achieved by the operator
carrying the device on their person. The USB port may be
used for charging the equipment when in the non-hazardous
area only.
For charging the device, use only Bartec approved chargers:
Charger with EU plug: G7-S0Z0-0001
Charger with UK plug: G7-S0Z0-0002
Charger with US plug: G7-S0Z0-0003
Charger with AU plug: G7-S0Z0-0004
Charging dock: G7-S0Z0-0007
Vehicle charging dock: G7-S0Z0-0008
For connection to computers and car chargers, use only
Bartec approved charging cable:
USB Safe Box cable G7-S0Z0-0006
Android is a trademark of Google LLC.
Conditions For Use (CSA)
Legal
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Bartec Pixavi User guide
Documents connexes
Autres documents
-
Endres+Hauser BA Field Xpert SMT77 Mode d'emploi
-
Mettler Toledo IND560x Guide d'installation
-
Rosemount Wireless Pressure Gauge Guide de démarrage rapide
-
Fluidwell F040 Le manuel du propriétaire
-
-
-