PowerStroke PS9C5001 Le manuel du propriétaire

Marque: PowerStroke

Modèle: PS9C5001

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

NEUTRAL BONDED TO FRAME

CONNECTEUR NEUTRE RELIÉ AU CADRE

PUNTO NEUTRO CONECTADO AL MARCO

CUSTOMER SERVICE (USA)

1-877-617-3501

SERVICE CLIENTELE (Canada)

1-877-617-3501

SERVICIO AL CLIENTE (Mexico)

01 800 843 1111

www.powerstroketools.com

To register your POWERSTROKE product, please visit:

http://register.powerstroketools.com/

Pour enregistrer votre produit de POWERSTROKE, s’il

vous plaît la visite : http://register.powerstroketools.com/

Para registrar su producto de POWERSTROKE, por favor

visita: http://register.powerstroketools.com/

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel

containing greater than 10% ethanol)

in this product. It is a violation of fed-

eral law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your generator has been engineered and manufactured to our high standard for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this

product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product.

Ce générateur a été conçu et fabriqué conformément à nos strictes

normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.

Correctement entretenu, cet outil vous donnera des années de

fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de blessures, l’utilisateur doit lire

et veiller à bien comprendre le manuel d’utilisation avant

d’employer ce produit. Si tous les avertissements et toutes les

consignes de sécurités et instructions du manuel d’utilisation

ne sont pas bien compris, ne pas utiliser ce produit.

Su generador diseñado y fabricado de conformidad con nuestras

estrictas normas para brindar fiabilidad, facilidad de uso y seguri-

dad para el operador. Con el debido cuidado, le brindará muchos

años de sólido funcionamiento y sin problemas.

ADVERTENCIA:

Para reducir el riesgo de lesiones, el usuario debe leer y

comprender el manual del operador antes de usar este

producto. Si no comprende los avisos de advertencia y las

instrucciones del manual del operador, no utilice este producto.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

5,000 WATT GENERATOR

GÉNÉRATEUR DE 5000 WATTS

GENERADOR 5 000 WATTS

PS9C5001

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulte esta sección desplegable para ver todas las figuras a

las que se hace referencia en el manual del operador.

Fig. 1

F - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite / varilla medidora de

aceite)

G - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

H - Stop switch (interruptor del apagado,

interruptor del apagado)

I - Recoil starter grip (poignée du lanceur,

mango del arrancador retráctil)

J - Air filter (filtre à air, filtro de aire)

K - Choke (volet de départ, anegador)

L - Fuel tank vapor vent (respirador del vapor del

tanque de combustible)

- Ground terminal (terminal de conexión a

tierra)

N - Fuel valve (válvula de combustible)

O - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

P - AC circuit breaker (disjoncteur c.a.,

disyuntorde circuito de CA)

Q - Handle (poignée, mango)

R - Wheel (roue, rueda)

S - Muffler (silencieux, silenciador)

A - Handle release pin (goupille de relâchement

de poignée, conjunto de pasador de afloje de

mango)

B - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

C - Fuel tank (réservoir de carburant, tanque de

combustible)

D - 120 volt AC 20 amp receptacles (réceptacles

120 volts, 20 ampères, 120 V de CA 20 A

receptáculos)

E - 240 volt AC 20 amp receptacle (réceptacle

240 volts, 20 ampères, 240 V de ca 20 A

receptáculo)

iii

Fig. 2

Fig. 3 Fig. 5 Fig. 7

A - Socket wrench (clé à douille, llave de

casquillo)

B - Combination wrench (clé mixte, llave de

combinación)

Fig. 4

A - Lock nut (écrous de blocage, tuerca de

bloqueo)

B - Frame (support, armazón)

C - Rubber foot (patin en caoutchouc, pie de

goma)

D - Bolt (boulon, perno)

A - Hitch pin (goupille d’attelage, pasador del

enganche)

B - Washer (rondelle, arandela)

C - Wheel (roue,rueda)

D - Axle (essieu, eje)

E - U-bracket (support en U, soporte en “U”)

Fig. 6

A - Lanyard (lanière, correa)

B - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

C - Handle (poignée mango)

D - Hole (trou, agujero)

A - Handle (poignée, mango)

B - Handle lock pin (goupille de blocage de la

poignée pasador de seguro del mango)

C - Handle release pin (goupille de relâchement

de poignée, conjunto de pasador de afloje de

mango)

RUN

START

CHOKE

Fig. 8

Fig. 9

Fig. 14

Fig. 12

Fig. 13

Fig. 10

Fig. 15

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Recoil starter grip (poignée du lanceur

mango, del arrancador retráctil)

A - Move choke lever left to start (tirer droite

le levier d’étranglement pour démarrer,

desplace izquierda la palanca del anegador

para arrancar)

B - Move choke lever right to run (tirer droite

le levier d’étranglement pour la marche,

desplace derecha de la palanca del anegador

para poner en marcha)

A - Air filter screw (vis du filtre à air, tornillo de

filtro de aire)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Filter element (elément filtrant, elemento de

filtro)

D - Air filter unit (unité de filtre à air, unidad del

filtro de aire)

A - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite / varilla medidora de

aceite)

B - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

A - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

B - Fuel tank (réservoir de carburant, tanque de

combustible)

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Stop switch (commutateur d’arrêt, interruptor

del apagado)

RUN

START

CHOKE

RUN

START

CHOKE

A B

Fig. 11

A - Spark plug (bougie, bujía)

B - Spark plug cap (creux de la bougie, tapa de

la bujía)

Fig. 21

Fig. 20

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Petcock (petit robinet, llave de purga)

C - Fuel valve (robinet de carburant, válvula de

combustible)

Fig. 16

Fig. 17

A - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

B - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite / varilla medidora de

aceite)

Fig. 18

A - Carburetor drain screw (carburetor drain

screw, tornillo de drenaje del carburador)

Fig. 22

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Fuel filter (filtre à carburant, filtro de

combustible)

Fig. 19

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Petcock (petit robinet, llave de purga)

Page 2 — English

 Introduction .................................................................................................................................................................... 2

 Important Safety Instructions .....................................................................................................................................3-4

 Specific Safety Rules ..................................................................................................................................................... 4

 Symbols ......................................................................................................................................................................5-7

 Electrical .....................................................................................................................................................................8-9

 Features ...................................................................................................................................................................... 10

 Assembly ................................................................................................................................................................11-12

 Operation ................................................................................................................................................................12-14

 Maintenance ...........................................................................................................................................................15-17

 Troubleshooting ........................................................................................................................................................... 18

 Warranty ..................................................................................................................................................................19-22

 Parts Ordering / Service..................................................................................................................................Back Page

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product, making it easy to maintain and operate.

DANGER:

GROUNDING THE GENERATOR

To reduce the risk of shock or electrocution, generator must be properly grounded. The

nut and ground terminal on the frame must always be used to connect the generator to

a suitable ground source. The ground path should be made with #8 size wire. Connect

the terminal of the ground wire between the lock washer and the nut, and tighten

the nut fully. Connect the other end of the wire securely to a suitable ground source.

The National Electric Code contains several practical ways in which to establish a

good ground source. If a steel or iron rod is used, it should be at least 5/8 in. diameter,

and if a nonferrous rod is used, it should be at least 1/2 in. diameter and be listed

as material for grounding. Drive the rod or pipe to a depth of 8 ft. If a rock bottom is

encountered less than 4 ft. down, bury the rod or pipe in a trench.

All electrical tools and appliances operated from this generator must be properly grounded by use

of a third wire or be “Double Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord intended for outdoor use with a 3-pole receptacle and a 3-prong plug at opposite ends to

ensure continuity of the ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.

TABLE OF CONTENTS

INTRODUCTION

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See a

doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below could result in electrocution,

fire, and/or carbon monoxide poisoning, which can cause

death or serious injury.

DANGER:

National Electric Code requires generator to be grounded

to an approved earth ground. Before using the ground ter-

minal, consult a qualified electrician, electrical inspector,

or local agency having jurisdiction for local codes or or-

dinances that apply to the intended use of the generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions for this product

that should be followed during installation and maintenance

of the generator.

 Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

 Do not allow children or untrained individuals to use this

unit.

 Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated space

where dangerous carbon monoxide fumes can collect.

Carbon monoxide, a colorless, odorless, and extremely

dangerous gas, can cause unconsciousness or death.

 Keep all bystanders, children, and pets at least 10 feet

away.

 Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

 Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

 Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

 Do not touch bare wire or receptacles.

 Do not use generator with electrical cords which are worn,

frayed, bare, or otherwise damaged.

 Before storing, allow the engine to cool and drain fuel

from the unit.

 Do not operate or store the generator in rain, snow, or

wet weather.

 Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

 Empty fuel tank, close fuel valve, and restrain the unit

from moving before transporting in a vehicle.

 Allow engine to cool for five minutes before refueling.

 To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

 Do not smoke while handling fuel.

 Store fuel in a container approved for gasoline.

 Position the unit on level ground, stop engine, and allow

to cool before refueling.

 Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

 Tighten the fuel cap securely after refueling.

 Wipe spilled fuel from the unit.

 Never attempt to burn off spilled fuel under any circum-

stances.

 Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

 For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

Page 4 — English

IMPORTANT SAFETY INSTRUCTIONS

SPECIFIC SAFETY RULES

 Use only authorized replacement parts and accessories

and follow instructions in the Maintenance section of this

manual. Use of unauthorized parts or failure to follow main-

tenance instructions may create a risk of shock or injury.

 Maintain the unit per maintenance instructions in this

Operator’s Manual.

 Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.

 Do not use this generator to provide power for emergency

medical equipment or life support devices.

 This generator has a neutral bonded condition. This

means the neutral conductor is electrically connected to

the frame of the machine.



Exhaust contains poisonous carbon monoxide, a colorless,

odorless gas. Breathing exhaust can cause loss of con-

sciousness and can lead to death. If running in a confined

or partially-enclosed area, the air may contain a danger-

ous amount of carbon monoxide. To keep exhaust fumes

from building up, always provide adequate ventilation.



Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.



Place the generator on a flat, stable surface with a slope

of no more than 4°.



Operate in a well-ventilated, well-lit area isolated from

working areas to avoid noise interference.



Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.



Keep the generator a minimum of 3 feet away from all

types of combustible material.



Do not operate generator near hazardous material.



Do not operate generator at a gas or natural gas filling

station.



Do not touch the muffler or cylinder during or immediately

after use; they are HOT and will cause burn injury.

 Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank cap

when the engine is running. Covering the fuel tank cap

during use may cause engine failure and/or damage to

the tool.



Do not smoke when filling the generator with gasoline.



Shut down the engine and allow to cool completely before

adding gasoline or lubricant to the generator.



Do not remove the oil dipstick or the fuel tank cap when

the engine is running.



Pay close attention to all safety labels located on the

generator.



Keep children a minimum of 10 feet away from the gen-

erator at all times.



The unit operates best in temperatures between 23°F and

104°F with a relative humidity of 90% or less.



Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To avoid damage, al-

ways have an additional load plugged into the generator

if solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

 For outdoor use only.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you loan

someone this product, loan them these instructions also.

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface To reduce the risk of injury or damage, avoid contact with any hot

surface.

Lifting Hazard To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground Consult with local electrician to determine grounding requirements

before operation.

Electrocution Failure to properly ground generator can result in electrocution,

especially if the generator is equipped with a wheel kit.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 6 — English

 You WILL be KILLED or SERIOUSLY

HURT if you do not follow the

Operator’s Manual instructions.

 Risk of Fire. Do not add fuel while

the product is operating.

 Generator is a potential source

of electric shock. Do not expose

to moisture, rain, or snow. Do not

operate with wet hands or feet.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

SAFETY LABELS

The information below can be

found on the generator. For

your safety, please study and

understand all of the labels before

starting the generator.

If any of the labels come off the

unit or become hard to read,

contact an authorized service

center for replacement.

 Do not expose to rain or use in damp

locations.

 Using a generator indoors CAN KILL

YOU IN MINUTES. Generator exhaust

contains carbon monoxide. This is a

poison you cannot see or smell.

 NEVER use inside a home or garage,

EVEN IF doors and windows are open.

 Only use OUTSIDE and far away from

windows, doors, and vents.

 Exhaust contains poisonous carbon

monoxide gas that can cause

unconsciousness or DEATH. Operate

in well-ventilated, outdoor areas away

from open windows or doors.

 Failure to properly ground generator

can result in electrocution, especially

if the generator is equipped with a

wheel kit.

You WILL be KILLED or SERIOUSLY

HURT if you do not follow the Operator’s

Manual instructions.

Ne pas procéder de la manière décrite

dans ce Manuel d’utilisation entraînera

des BLESSURES GRAVES voire la MORT.

SE MATARÁ o LESIONARÁ GRAVEMENTE

si no sigue las instrucciones del Manual

del operador.

Risk of fire. Do not add fuel while the

product is operating.

Risque d’incendie. Ne pas ajouter de

carburant pendant l’utilisation de

l’appareil.

Riesgo del incendio. No agregue

combustible cuando el producto esté

functionando.

Generator is a potential source of electric

shock. Do not expose to moisture, rain, or

snow. Do not operate with wet hands or feet.

Le générateur est une source potentielle

de chocs électriques. Ne pas exposer à l’humidité,

la pluie ou la neige. Ne pas utiliser avec les

mains ou les pieds mouillés.

El generador es una fuente de descarga eléctrica.

No lo exponga a humedad, la lluvia, nin a la

nieve. No opere con manos o pies húmedos.

Exhaust contains poisonous carbon monoxide

gas that can cause unconsciousness or DEATH.

Operate in well ventilated, outdoor areas away

from open windows or doors.

L’échappement contient le gaz monoxyde de

carbone toxique qui peut causer l’inconscience

ou la MORT. Fonctionner dans les secteurs

bien ventilés et extérieurs loin d’ouvre des

fenêtres ou des portes.

El escape contiene gas venenoso de monóxido

de carbono que puede causar pérdida del

conocimiento o MUERTE. Opere en áreas exteriores

bien ventiladaslejos de puertas o ventanas abiertas.

Failure to properly ground generator can

result in electrocution, especially if the

generator is equipped with a wheel kit.

Une mauvaise mise à la terre du générateur

peut causer une électrocution, surtout si le

générateur est équipé d’un kit de roue.

La omisión de conectar a tierra

adecuadamente el generador puede resultar

en electrocución, especialmente si el

generador está equipado con un kit de ruedas.

Do not expose to rain or use in damp

locations.

Ne pas exposer à la pluie ou l’humidité.

No exponga a la lluvia ni use en lugares

húmedos.

DANGER PELIGRO

DANGER

940654199-01

DANGER DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone, un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un garage,MÊME SI les portes et

les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres, des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN POCOS MINUTOS.

Los gases de escape del generador contienen monóxido de carbono. Es un veneno

que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO con las puertas y las

ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

Page 7 — English

SYMBOLS

FUEL WARNING

No smoking when filling with gasoline.

Do not overfill. Full level is 1 in. below

the top of the fuel neck. Stop the en-

gine for five minutes before refueling to

avoid the heat from the muffler igniting

fuel vapors.

ENGINE LUBRICANT WARNING

You must add lubricant before first

operating the generator. Always check

the lubricant level before each opera-

tion. The lubricant level should always

the dipstick. The unit is equipped with

a sensor which will automatically shut

off the engine if the lubricant level falls

below a safe limit.

GROUNDING WARNING

National Electric Code requires gen-

erator to be grounded to an approved

earth ground.

HOT SURFACE WARNING

Do not touch the muffler or aluminum

cylinder of the engine. They are very HOT

and will cause severe burns. Don’t put

any flammable or combustible materials

in the direct path of the exhaust.

CLEARANCE WARNING

While operating and storing, keep at

least 3 feet of clearance on all sides of

this product, including overhead. Al-

low a minimum of 30 minutes of “cool

down” time before storage. Heat creat-

ed by muffler and exhaust gases could

be hot enough to cause serious burns

and/or ignite combustible objects.

SPARK ARRESTOR

Operation of this equipment may create

sparks that can start fires around dry

vegetation. A spark arrestor may be re-

quired. The operator should contact lo-

cal fire agencies for laws or regulations

relating to fire prevention requirements.

940513001-04

Product does not include ground rod or copper wire. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an electrician for local grounding requirements.

Le produit ne comprend pas de piquet de terre ou de fil en cuivre. Le code electrique americain

(National Electric Code) requiert un générateur pour une bonne mise à la terre approuvée. Appeler un

électricien pour connaître les exigences locales de mise à la terre.

El producto no incluye el ealambre de cobre ni la barra de conexión a tierra. Los Reglamentos

Nacionales de Electricidad exigen que el generador esté debidamente conectado a una tierra aprobada.

Comuniquese con un electrista para todo lo relacionado con los requistos de conexión a tierra.

HOT SURFACE

SURFACES TRÉS CHAUDE

SUPERFICIES CALIENTE

WARNING

AVERTISSEMENT

ADVERTENCIA

940680027-03

CHECK LUBRICANT

940708019-03

Risk of Fire. Check for any fuel overflow or leaking. Stop the engine before refueling.

DANGERDANGER PELIGRO

Risque d’incendie. Vérifier l'absence de débordement ou de fuite de carburant.

Arrêter le moteur avant de fair le plein.

Riesgo de incendio. Revise si hay algún derrame o fuga de combustible. Apague el

motor antes de poner combustible. 940974007-04

DANGERDANGER PELIGRO

940974089-02

Risk of Fire. Keep all objects at least 3 feet away from this machine. Heat from Muffler and Exhaust gases

can ignite combustible objects.

Risque d’incendie. Éloigner tous les objets au moins de 91,4 cm (3 pi) de cet appareil. La chaleur

du pot d’échappement et les gaz d’échappement peuvent enflammer les objets combustibles.

Riesgo de incendio. Mantener todos los objetos a una distancia mínima de 91,4 cm (3 pies) de esta

máquina. El calor de los gases del silenciador y el escape pueden prender fuego a objetos combustibles.

Operation of this equipment may create sparks that can start fires

around dry vegetation. A spark arrestor may be required. The operator should contact

local fire agencies for laws or regulations relating to fire prevention requirements.

WARNING

AVERTISSEMENT

L’utilisation de cet équipement peut créer des étincelles

susceptibles d’enflammer la végétation sèche. Il peut être nécessaire d’utiliser un

pare-étincelles. L’utilisateur doit communiquer avec le service local d’incendie pour

connaître toutes les lois et tous les règlements portant sur les exigences en matière

de prévention des incendies.

940947003-03

ADVERTENCIA

El uso de este equipo puede producir chispas propensas a

iniciar incendios cerca de vegetación seca. Es posible que se necesite un parachis-

pas. El operador debe ponerse en contacto con las agencias contra incendios locales

para conocer las leyes y regulaciones relacionadas con los requisitos de prevención

de incendios.

Page 8 — English

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can burn out the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 3600 150 ft. 100 ft. 65 ft.

20 2400 4800 175 ft. 125 ft. 75 ft.

25 3000 6000 150 ft. 100 ft.

30 3600 7200 125 ft. 65 ft.

40 4800 9600 90 ft.

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while starting.

This table may be used to estimate the watts required to start electric motors; however, if an electric motor fails to start or

reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check the requirements

of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts Watts Required to Start Motor

Universal Capacitor Split Phase

1/8 275 N/A 850 1200

1/6 275 600 850 2050

1/4 400 800 1050 2400

1/3 450 950 1350 2700

1/2 600 1000 1800 3600

3/4 850 1200 2600 —

1 1100 N/A 3300 —

NOTICE:

Operating voltage and frequency requirement of all electronic equipment should be checked prior to plugging them into

this generator. Damage may result if the equipment is not designed to operate within a +/- 10% voltage variation, and

+/- 3 hz frequency variation from the generator name plate ratings. To avoid damage, always have an additional load

plugged into the generator if solid state equipment (such as a television set) is used. A power line conditioner is recom-

mended for some solid state applications.

ELECTRICAL

Page 9 — English

Example:

Tool or Appliance Running

Watts*

Additional

Starting Watts*

RV Air Conditioner

(11,000 BTU) 1010 1600

TV (Tube Type) 300 0

RV Refrigerator 180 600

Radio 200 0

Light (75 Watts) 300 0

Coffee Maker 600 0

2590 Total

Running Watts

1600 Highest

Starting Watts

Total Running Watts 2590

Highest Starting Watts + 1600

Total Starting Watts Needed 4190

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to start

electric motor-driven tools or appliances such as a circular

saw or refrigerator. Because not all motors start at the

same time, total surge watts can be estimated by adding

only the item(s) with the highest additional surge watts to

the total rated watts from step 2.

NOTICE:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity may damage

the generator and/or electrical devices connected to it.

ELECTRICAL

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

Tool or Appliance

Estimated*

Running

Watts

Estimated*

Additional

Starting Watts

Home / Emergency

Incandescent Lights

(4 Quantity x 75 Watts) 300 0

TV (Tube Type) 300 0

Sump Pump (1/3 hp) 800 1300

Refrigerator or Freezer 700 2200

Well Pump (1/3 hp) 1000 2000

Furnace (1/2 hp) 800 2350

Radio 200 0

Tools

Drill (3/8", 4 amps) 440 600

Circular Saw

(Heavy Duty, 7-1/4")

1400 2300

Recip Saw 960 960

Miter Saw (10") 1800 1800

Table Saw (10") 2000 2000

*Wattages listed are approximate. Check tool or equipment for actual wattage.

Page 10 — English

KNOW YOUR GENERATOR

See Figure 1.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AC CIRCUIT BREAKER

The circuit breaker is provided to protect the generator

against electrical overload. The circuit breaker may be reset

by flipping down and back up.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

CHOKE LEVER

The choke lever is used when starting the engine.

FUEL TANK

The fuel tank has a capacity of 6 gallons.

FUEL VALVE

Fuel flow from the fuel tank to the engine is turned on and

off using the fuel valve.

GROUND TERMINAL

The ground terminal is used to assist in properly ground-

ing the generator to help protect against electrical shock.

Consult with a local electrician for grounding requirements

in your area.

LOW OIL SHUT DOWN PROTECTOR

The low oil sensor causes the engine to stop if the level of

oil in the crankcase is insufficient.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

generator when necessary.

OIL DRAIN PLUG

When changing the engine lubricant, unscrew and remove

the oil drain plug to allow old engine lubricant to be drained.

RECEPTACLES

Your generator has the following single phase, 60 Hz out-

lets: one 240 Volt AC 20 Amp twist lock receptacle and two

120 Volt AC, 20 Amp duplex receptacles. These can be used

for operating appropriate appliances, electrical lighting, tools,

and motor loads.

RECOIL STARTER GRIP

The recoil starter grip is used to start the generator’s engine.

STOP SWITCH

The generator has a stop switch near the fuel valve. To turn

the engine off, press and hold the STOP switch until the

engine stops.

FEATURES

PRODUCT SPECIFICATIONS

ENGINE

Engine Type .......................................................389cc OHV

Spark Plug ................................................ Torch/LG F6RTC

Engine Lubricant Volume........................................... 37 oz.

Fuel Volume ................................................................ 6 gal.

GENERATOR

Rated Voltage ...................................................120V / 240V

Rated Amps ................................................... 41.7A / 20.8A

Rated Running Watts* ............................................5,000 W

Rated Starting Watts ..............................................6,250 W

Rated Frequency ........................................................60 Hz

DIMENSIONS

Length ..................................................................... 28.5 in.

Width ....................................................................... 20.9 in.

Height ...................................................................... 24.1 in.

Weight .................................................................... 190 lbs.

*Rated running watts determined by PGMA Standard G200

Page 11 — English

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

machine and any accessories from the box. Make sure

that all items listed in the loose parts list are included.

NOTE: This machine is heavy and requires a minimum of

two people to lift. To avoid back injury, lift with your legs

and not your back.

WARNING:

Do not use this product if any parts on the Loose Parts

List are already assembled to your product when you

unpack it. Parts on this list are not assembled to the

product by the manufacturer and require customer instal-

lation. Use of a product that may have been improperly

assembled could result in serious personal injury.

 Inspect the unit carefully to make sure no damage oc-

curred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-877-617-3501 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

LOOSE PARTS LIST

See Figure 2

The following items are included with the generator:

Key

No. Description Qty.

1 Axle ......................................................................2

2 Wheel ...................................................................2

3 Washer ................................................................. 2

4 Hitch Pin ..............................................................2

5 Bolt ......................................................................2

6 Rubber Foot ........................................................2

7 Lock Nut ..............................................................2

8 Bottle of Engine Lubricant ...................................1

Operator’s Manual (not shown) ...........................1

TOOLS NEEDED

See Figure 3.

The following tools (not included or drawn to scale) are

needed for assembly:

 Socket Wrench

 Combination Wrench

NOTE: Do not put fuel or lubricant in the generator before

installing the feet and wheels.

INSTALLING FEET ON THE FRAME

See Figure 4.

 Locate the following items:

2 rubber feet

2 lock nuts

2 bolts

 Insert bolt through rubber foot and then through frame

as shown.

 Thread lock nut onto bolt and tighten one full turn past

snug.

NOTE: Be careful not to overtighten so that foot mate-

rial collapses.

 Repeat with remaining foot.

ASSEMBLY

Page 12 — English

INSTALLING THE WHEELS

See Figure 5.

Wheels are provided to assist in moving the generator to

the desired location and should be installed on the side

opposite the handle.

 Locate the following items:

2 axle

2 washers

2 wheels

2 hitch pins

 Raise the end of the generator opposite the recoil starter

high enough to gain access to the frame bottom; securely

position props underneath to support.

 Insert axle through the center of the wheel.

 Place washer on axle and then slide the axle through the

bracket on the frame.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.



Repeat the process on the other side to install second

wheel.

ASSEMBLY

OPERATION

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

 Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

 ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

DANGER:

Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an

electrician for local grounding requirements.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

Page 13 — English

OPERATION

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

 Only use OUTSIDE and far away from windows, doors,

and vents.

 NEVER use inside a home or garage, EVEN IF doors and

windows are open.

 Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

 In some areas, generators are required to be registered

with local utility companies.

 If the generator is used at a construction site, there may

be additional regulations which must be observed.

RAISING AND LOWERING THE HANDLE

See Figure 6 - 7.

 Attach the lanyard to the handle lock pin and generator.

 To raise the handle (for moving the generator): pull the

handle release pin out and raise the handle. Release the

handle release pin and insert the handle lock pin to secure

the handle in place.

 To lower the handle (for storing or transporting the gen-

erator): remove the handle lock pin, then pull the handle

release pin out and lower the handle to the down position.

Never use the handle to lift the generator. The handle should

only be used for moving the unit by rolling it on its wheels.

CHECKING/ADDING LUBRICANT

See Figure 8.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke motor

lubricant that meets or exceeds the requirements for API

service classification SJ.

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

 Turn the fuel valve to the OFF position.

 Unscrew the oil cap/dipstick and remove.

 Wipe dipstick clean and re-seat in hole; do not rethread.

 Remove dipstick again and check lubricant level. Lubri-

cant level should fall between the hatched areas on the

dipstick.

 If level is low, add engine lubricant until the fluid level rises

to the upper portion of the dipstick.

 Replace and secure the oil cap/dipstick.

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

 Mix fuel stabilizer and gasoline prior to filling the tank

by using a gas can or other approved fuel container and

shaking gently to combine.

NOTE: To control the amount of fuel stabilizer being added

to the engine, always mix fuel stabilizer with gasoline

before fueling the tank rather than adding fuel stabilizer

directly into the generator’s fuel tank.

 Replace and secure the fuel tank cap.

 Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

CHECKING/ADDING FUEL

See Figure 9.

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from igni-

tion sources, handle outdoors only, do not smoke while

adding fuel, and wipe up spills immediately.

Page 14 — English

When adding gas to the generator, make sure the unit is

sitting on a flat, level surface. If the engine is hot, let the

generator cool before adding gas. ALWAYS fill the fuel tank

outdoors with the machine turned off.

 Remove the fuel cap.

 Fill the fuel tank to 1 in. below the top of the fuel neck.

 Replace and secure the fuel cap.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow dirt

or water into the fuel tank. Do not use E85 fuel.

STARTING THE ENGINE

See Figures 10 - 12.

NOTICE:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

 Unplug all loads from the generator.

 Turn the fuel valve to the ON position.

 Move the choke lever left to the START position.

NOTE: If engine is warm or the temperature is above

50˚F,movethechokeleverrighttotheRUNposition.

 Pull the recoil starting grip until the engine runs (a maxi-

mum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

 Allow the engine to run for 15 - 30 seconds, then move

the choke to the RUN position.

STOPPING THE ENGINE

See Figure 12.

To stop the engine under normal operating conditions:

 Remove any load from the generator.

 Turn the fuel valve to the OFF position.

 Press and hold the STOP switch until the engine stops.

To stop the unit quickly in an emergency:

 Press and hold the STOP switch until the engine stops.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time be-

fore storage. Heat created by muffler and exhaust gases

can be hot enough to cause serious burns and/or ignite

combustible objects.

MOVING THE GENERATOR

See Figure 13.

 Turn off the generator.

 Raise the handle to the up position.

 Disconnect any equipment that is plugged into the gen-

erator.

 Turn the fuel valve to the OFF position.

 Allow 30 minutes of “cool down” time before storing the

machine.

 For security, insert the handle lock pin to secure the handle

before moving.

NOTE: To help keep the handle lock pin securely in the

hole, push the joined area of the lanyard toward the inside

of the generator frame.

 With your foot on the rear of the frame, tilt the machine

toward you until it balances on the wheels, then roll the

machine to the desired location.

LIFTING THE GENERATOR

See Figure 14.

 Turn off the generator.

 Fold the handle to the down position. Never lift or carry

this product using the handle.

NOTE: This tool is heavy and requires several people to

lift. To avoid back injury, keep your knees bent and lift

with your legs, not your back, and get help when needed.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation

for equipment operating in altitudes greater than 3000 feet

above sea level. Please contact your authorized service cen-

ter for important information regarding these modifications.

Operating this engine without the proper altitude modifica-

tion may increase the engine’s emissions and decrease fuel

economy and performance.

OPERATION

Page 15 — English

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts can create a hazard or cause

product damage.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water en-

tering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

 Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

 Clean air vents with low pressure air that does not exceed

25 psi.

 Wipe the exterior surfaces of the generator with a damp

cloth.

CHECKING/CLEANING AIR FILTER

See Figure 15.

For proper performance and long life, keep air filter clean.

 Loosen the screw on the bottom of the air filter cover.

Remove cover and set aside.

 Remove the filter element.

 If the filter element is dirty, clean with warm, soapy water.

Rinse and let dry.

 Apply a light coat of engine lubricant to the element, then

squeeze it out.

 Replace the element in the air filter unit.

 Replace the air filter cover and tighten screw to secure.

NOTE: Do not run the generator without the air filter. Rapid

engine wear will result.

CHANGING ENGINE LUBRICANT

See Figure 16.

 Remove the oil cap/dipstick.

 Place a container underneath the oil drain plug to collect

used lubricant as it drains.

 Unscrew the oil drain plug and remove.

 Allow lubricant to drain completely.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

 Reinstall the oil drain plug and tighten securely.

 Refill with lubricant following the instructions in the

Checking/Adding Lubricant section. For amount of

lubricant needed to refill, see Product Specifications

earlier in this manual or the accompanying engine manual,

if applicable.

 Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local oil retailer for more information.

SPARK PLUG MAINTENANCE

See Figure 17.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

 Remove the spark plug cap.

 Clean any dirt from around base of spark plug.

 Remove spark plug using wrench (not included).

 Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or chipped,

spark plug should be replaced.

NOTE: For replacement spark plug, see Product Specifi-

cations earlier in this manual or the accompanying engine

manual, if applicable.

 Measurepluggap.Thecorrectgapis0.028−0.031in.

(0.7-0.8 mm). To widen gap, if necessary, carefully bend

the ground (top) electrode. To lessen gap, gently tap

ground electrode on a hard surface.

 Seat spark plug in position; thread in by hand to prevent

cross-threading.

 Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

MAINTENANCE

Page 16 — English

CLEANING THE EXHAUST PORT AND

MUFFLER

Depending on the type of fuel used, the type and amount of

lubricant used, and/or your operating conditions, the exhaust

port and muffler may become blocked with carbon deposits.

If you notice a power loss with your gas-powered products,

you may need to remove these deposits to restore perfor-

mance. We highly recommend that only qualified service

technicians perform this service.

SPARK ARRESTOR

See Figure 18.

 Inspect the spark arrestor for breaks or holes. Re-

place if necessary. To purchase a replacement spark

arrestor contact Powerstroke customer service at

1-877-617-3501.

 Use a brush to remove carbon deposits from the spark

arrestor screen as needed.

DRAINING FUEL TANK/CARBURETOR

See Figures 19 - 21.

To help prevent gum deposits in the fuel system, drain the

fuel from the tank and carburetor before storing.

DRAINING THE FUEL TANK:

 Turn off the generator.

 Turn the fuel valve to the OFF position.

 Push the fuel valve knob through the generator housing

and pull down slightly to gain access to the petcock.

 Remove the fuel line from the petcock by squeezing the

ends of the retaining clip and sliding the fuel line off.

 Install one end of a drain line over the petcock, and place

the other end in a fuel container large enough to catch

the fuel being drained from the tank.

 Turn the fuel valve to the ON position.

 When the fuel has drained from the tank, close the fuel

valve and reinstall fuel line securely on petcock.

 Reinstall fuel valve knob in generator housing. Push for-

ward until knob snaps securely into position.

DRAINING THE CARBURETOR:

 Turn off the generator.

 Turn the fuel valve to the OFF position.

 Position a suitable container under the carburetor drain

screw to catch fuel; loosen the screw.

 Allow fuel to drain completely into container.

 Retighten drain screw.

NOTE: Consult hazardous waste management guidelines in

your area for the proper way to dispose of used fuel.

REPLACING FUEL FILTER

See Figure 22.

Occasionally the fuel filter may become clogged and need

replacing. To purchase a replacement fuel filter contact

Powerstroke customer service at 1-877-617-3501.

NOTE: Fuel tank must be empty before replacing fuel filter.

Run unit until tank is empty, if needed, or inspect filter prior

to fill-up.

 Turn the fuel valve to the OFF position.

 Push the fuel valve knob through the generator housing

and pull down slightly to gain access to the filter.

 Remove the fuel line from both sides of the filter by

squeezing the ends of the retaining clip with pliers.

 Slide the fuel line off.

 Replace with new fuel filter.

 Reinstall fuel lines to new fuel filter.

 Reinstall fuel valve knob in generator housing. Push for-

ward until knob snaps securely into position.

 Turn the fuel valve to the ON position.

TRANSPORTING

 Turn off the generator.

 Turn the fuel valve to the OFF position.

 Make sure engine and exhaust of unit is cool.

 Empty the fuel tank.

 Do not drop or strike unit or place under heavy objects.

MAINTENANCE

La page charge ...

PowerStroke PS9C5001 Le manuel du propriétaire

Marque: PowerStroke

Modèle: PS9C5001

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PowerStroke PS9C5001 Owner's manual
español: PowerStroke PS9C5001 El manual del propietario

PowerStroke PS9C5001 Le manuel du propriétaire

PowerStroke PS9C5001 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents