Klein Tools MM600 Manuel utilisateur

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

INSTRUCTION MANUAL

ENGLISH

MM700

1000V

10A

40M

Ω

• DATA & RANGE HOLD

• LOW IMPEDANCE

• AUDIBLE CONTINUITY

• MIN / MAX / RELATIVE

• TEMPERATURE

• DIODE TEST

• CAPACITANCE &

FREQUENCY

FRANÇAIS pg. 37

ESPAÑOL pg. 19

Auto-Ranging

Digital Multimeter

True RMS

Measurement

Technology

MM700-1390112ART.indd 1 9/21/2015 2:44:45 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

2

GENERAL SPECIFICATIONS

Klein Tools MM700 is an automatically ranging true root mean square

(TRMS) digital multimeter that measures AC/DC voltage, AC/DC current,

and resistance. It can also measure temperature, capacitance, frequency,

duty-cycle, test diodes and continuity.

• Operating Altitude: 6562 ft. (2000m)

• Relative Humidity: <90% non-condensing

• Operating Temp: 14°F to 122°F (-10°C to 50°C)

• Storage Temp: -4°F to 140°F (-30°C to 60°C)

• Accuracy: Values stated at 65°F to 83°F (18°C to 28°C)

• Temp Coefcient: 0.1 x (Quoted Accuracy) per °C above

28°C or below 18°C, corrections are required when ambient

working temp is outside of Accuracy Temp range

• Dimensions: 7.02" x 3.54" x 2.10" (178.3 x 89.9 x 53.3 mm)

• Weight: 14.6 oz. (414 g)

• Calibration: Accurate for one year

• Standards: Conforms to: UL STD 61010-1, 61010-2-030,

61010-2-033.

Certified to: CSA STD C22.2 # 61010-1,

61010-2-030, 61010-2-033.

IEC EN 61010-1, 61010-2-030,

61010-2-033, 61326-1.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 6.6 ft. (2m)

• Ingress Protection: IP42 (except test lead jacks, see WARNINGS)

• Safety Rating:

CAT IV 600V, CAT III 1000V, Class 2,

Double insulation

CAT III: Measurement category III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC EN 61326-1. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

RESISTANCE (AUTO-RANGING)

Function Resolution Accuracy

400.0Ω 0.1Ω

±(1.5% + 5 digits)

4.000kΩ 1Ω

40.00kΩ 10Ω

400.0kΩ 100Ω

4.000MΩ 1kΩ ±(2.0% + 10 digits)

40.00MΩ 10kΩ

Maximum Input: 600V DC or 600V AC RMS

MM700-1390112ART.indd 2 9/21/2015 2:44:46 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

3

ELECTRICAL SPECIFICATIONS

VOLTAGE (AUTO-RANGING)

Function Range Resolution Accuracy (

50–60 Hz

)

AC Voltage

(V AC)

4.000V 1mV ±(1.0% + 5 digits)

40.00V 10mV ±(1.2% + 5 digits)

400.0V 100mV ±(1.5% + 5 digits)

1000V 1V

DC Voltage

(V DC)

400.0mV 0.1mV ±(1.0% + 8 digits)

4.000V 1mV

±(1.0% + 3 digits)40.00V 10mV

400.0V 100mV

1000V 1V ±(1.2% + 3 digits)

Input Impedance: 10MΩ

Frequency Range: 50 to 400Hz

Maximum Input: 1000V AC RMS or 1000V DC

CURRENT (AUTO-RANGING)

AC Current

(A and mA)

400.0μA 0.1μA

±(1.5% + 3 digits)

4000μA 1μA

40.00mA 10μA

400.0mA 100μA

10.00A 0.01A ±(2.0% + 5 digits)

DC Current

(A and mA)

400.0μA 0.1μA

±(1.0% + 3 digits)

4000μA 1μA

40.00mA 10μA

400.0mA 100μA

10.00A 0.01A ±(1.5% + 3 digits)

Overload Protection: 500mA / 1000V and 10A / 1000V Fuses

Frequency Range: 50 to 400Hz

Maximum Input: µA/mA setting: 400mA AC RMS / DC

10A setting: 10A AC RMS / DC

RESISTANCE (AUTO-RANGING)

Function Resolution Accuracy

400.0Ω 0.1Ω

±(1.5% + 5 digits)

4.000kΩ 1Ω

40.00kΩ 10Ω

400.0kΩ 100Ω

4.000MΩ 1kΩ ±(2.0% + 10 digits)

40.00MΩ 10kΩ

Maximum Input: 600V DC or 600V AC RMS

MM700-1390112ART.indd 3 9/21/2015 2:44:46 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

4

ELECTRICAL SPECIFICATIONS

OTHER MEASUREMENT APPLICATIONS

Maximum Input: 100V RMS in Voltage setting,

600V DC or 600V AC RMS in all other settings

• Diode Test: 1.5 mA max, open circuit voltage 3.0V DC

• Continuity Check: Audible signal when resistance <50Ω,

max test current 0.35mA

• Low Impedence (Low Z): Input impedence >3kΩ

Max input 600V RMS

• Auto Power off: After ~30 minutes of inactivity

• Sampling Frequency: 3 samples per second

• Bar Graph: 41 segment, 10-15 samples per second

• Overload: "OL" indicated on display, 1000V RMS in voltage

settings, 600V RMS in all other settings

• Polarity: "-" on display indicates negative polarity

• Display: 3 ¾ digit, 4000 Count LCD, TRMS technology

ELECTRICAL SPECIFICATIONS

CAPACITANCE (AUTO-RANGING)

Range Resolution Accuracy

40.00nF 10pF ±(5.0% + 35 digits)

400.0nF 0.1nF

±(3.0% + 5 digits)

4.000μF 1nF

40.00μF 10nF

400.0μF 100nF

4000μF 1μF ±(5.0% + 5 digits)

Maximum Input: 600V DC or 600V AC RMS

FREQUENCY (AUTO-RANGING)

9.999Hz 0.001Hz

±(1.0% + 5 digits)

99.99Hz 0.01Hz

999.9Hz 0.1Hz

9.999kHz 1Hz

99.99kHz 10Hz

500.0kHz 100Hz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

DUTY CYCLE

1% to 99.9%

0.1% ±(1.2% + 2 digits)

Pulse width: 0.1 – 100ms

Frequency width: 5Hz to 10kHz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

TEMPERATURE

0° to 1500°F 0.1°F / 1°F ±(2.0% + 9°F)

-18° to 816°C 0.1°C / 1°C ±(2.0% + 5°C)

ENGLISH

WARNINGS

To ensure safe operation and service of the meter, follow these

instructions. Failure to observe these warnings can result in

severe injury or death.

• Before each use verify meter operation by measuring a known

voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT IV rated test leads.

• Ensure meter leads are fully seated, and keep fingers away

from the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes

are connected.

• Use caution when working with voltages above 25V AC RMS

or 60V DC. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,

replace batteries when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live

circuit.

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury

where hazardous live conductors are exposed.

• Meter is IP42 dust & water resistant. Following any contact

with water, thoroughly dry meter and test lead jacks prior to

subsequent use.

MM700-1390112ART.indd 4 9/21/2015 2:44:46 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

5

ELECTRICAL SPECIFICATIONS

OTHER MEASUREMENT APPLICATIONS

Maximum Input: 100V RMS in Voltage setting,

600V DC or 600V AC RMS in all other settings

• Diode Test: 1.5 mA max, open circuit voltage 3.0V DC

• Continuity Check: Audible signal when resistance <50Ω,

max test current 0.35mA

• Low Impedence (Low Z): Input impedence >3kΩ

Max input 600V RMS

• Auto Power off: After ~30 minutes of inactivity

• Sampling Frequency: 3 samples per second

• Bar Graph: 41 segment, 10-15 samples per second

• Overload: "OL" indicated on display, 1000V RMS in voltage

settings, 600V RMS in all other settings

• Polarity: "-" on display indicates negative polarity

• Display: 3 ¾ digit, 4000 Count LCD, TRMS technology

ELECTRICAL SPECIFICATIONS

CAPACITANCE (AUTO-RANGING)

Range Resolution Accuracy

40.00nF 10pF ±(5.0% + 35 digits)

400.0nF 0.1nF

±(3.0% + 5 digits)

4.000μF 1nF

40.00μF 10nF

400.0μF 100nF

4000μF 1μF ±(5.0% + 5 digits)

Maximum Input: 600V DC or 600V AC RMS

FREQUENCY (AUTO-RANGING)

9.999Hz 0.001Hz

±(1.0% + 5 digits)

99.99Hz 0.01Hz

999.9Hz 0.1Hz

9.999kHz 1Hz

99.99kHz 10Hz

500.0kHz 100Hz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

DUTY CYCLE

1% to 99.9%

0.1% ±(1.2% + 2 digits)

Pulse width: 0.1 – 100ms

Frequency width: 5Hz to 10kHz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

TEMPERATURE

0° to 1500°F 0.1°F / 1°F ±(2.0% + 9°F)

-18° to 816°C 0.1°C / 1°C ±(2.0% + 5°C)

WARNINGS

To ensure safe operation and service of the meter, follow these

instructions. Failure to observe these warnings can result in

severe injury or death.

• Before each use verify meter operation by measuring a known

voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT IV rated test leads.

• Ensure meter leads are fully seated, and keep fingers away

from the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes

are connected.

• Use caution when working with voltages above 25V AC RMS

or 60V DC. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock,

replace batteries when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live

circuit.

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury

where hazardous live conductors are exposed.

• Meter is IP42 dust & water resistant. Following any contact

with water, thoroughly dry meter and test lead jacks prior to

subsequent use.

MM700-1390112ART.indd 5 9/21/2015 2:44:46 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

6

SYMBOLS ON METER

AC/DC Voltage or Current Resistance (in Ohms)

Audible Continuity Diode

Capacitance

Hz

Frequency

%

Duty-cycle Double Insulated Class II

°

F/

°

C

Temperature (Fahrenheit / Celsius) Ground

Fuse (with rating below symbol)

Low Impedence

Warning or Caution

To ensure safe operation and service of this meter, follow all warnings

and instructions detailed in this manual.

Risk of Electrical Shock

Improper use of this meter can lead to risk of electrical shock. Follow

all warnings and instructions detailed in this manual.

ENGLISH

SYMBOLS ON LCD

H

Data Hold Audible Continuity

Diode Auto Ranging

AC (Alternating Current) DC (Direct Current)

Low Battery Auto Power Off

MAX

Maximum Value

MIN

Minimum Value

°F

Degrees Fahrenheit

°C

Degrees Celsius

M

Mega (value x 10

6

)

k

kilo (value x 10

3

)

m

mili (value x 10

-3

)

μ

micro (value x 10

-6

)

n

nano (value x 10

-9

)

V

Volts

A

Amps

F

Farads

Ohms

Hz

Hertz (Frequency)

%

Duty-Cycle

REL

Relative Mode

Bar Graph

MM700-1390112ART.indd 6 9/21/2015 2:44:47 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

7

FEATURE DETAILS

SYMBOLS ON LCD

H

Data Hold Audible Continuity

Diode Auto Ranging

AC (Alternating Current) DC (Direct Current)

Low Battery Auto Power Off

MAX

Maximum Value

MIN

Minimum Value

°F

Degrees Fahrenheit

°C

Degrees Celsius

M

Mega (value x 10

6

)

k

kilo (value x 10

3

)

m

mili (value x 10

-3

)

μ

micro (value x 10

-6

)

n

nano (value x 10

-9

)

V

Volts

A

Amps

F

Farads

Ohms

Hz

Hertz (Frequency)

%

Duty-Cycle

REL

Relative Mode

Bar Graph

1

8

11

10

7 9

2

3 5

46

NOTE: There are no user-serviceable parts inside meter.

1. 4000 count LCD display 7. "RANGE" button

2. Function selector switch 8. "REL" (Relative) button

3. "10A" jack 9. "MAX/MIN" button

4. "COM" jack 10. "HOLD" button

5. "VΩ" jack 11. "SEL" (Select) button

6. mA / µA jack

MM700-1390112ART.indd 7 9/21/2015 2:44:48 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

8

FUNCTION BUTTONS

ON/OFF

To Power ON the meter rotate the Function Selector switch

2

from

the OFF setting to any measurement setting. To Power OFF the meter

rotate the Function Selector switch

2

to the OFF setting. By default

the meter will automatically Power OFF after 30 minutes of inactivity.

Reactivate meter by pressing any button. To deactivate the automatic

Power OFF feature, power the meter ON with the SEL button

11

depressed. When automatic Power OFF is deactivated, the

symbol will not be visible in the display.

When the Function Selector switch is rotated to a measurement

setting, "LEAD" flashes on the display as a reminder to check that test

leads are inserted into the appropriate jacks.

"SEL" (SELECT) BUTTON (FOR SECONDARY FUNCTIONS)

The "SEL" button

11

activates the secondary functions for each

setting accessible by the Function Selector switch

2

. For Current,

Voltage and Low Z, it toggles between AC and DC. For the other

functions, it switches between °F and °C, between Hz and %

Duty-cycle, and between Continuity, Resistance, and Diode-test.

The default function for each application is printed on the meter in

white; the secondary functions are printed on the meter in orange.

"HOLD" (DATA HOLD / BACKLIGHT) BUTTON

Press HOLD

10

to hold the measurement on the display. Press

again to release the display to return to live measuring.

Press and hold the "HOLD" button

10

for more than one second to

turn on or off the backlight. The backlight will automatically Power

OFF following three minutes of inactivity to conserve battery life.

"RANGE" BUTTON

The meter defaults to auto-ranging measurement mode . This

automatically determines the most appropriate measurement range

for the testing that is being conducted. To manually force the meter

to measure in a different range, use the "RANGE" button

7

.

1. Press the "RANGE" button

7

to manually select measurement

range ( is deactivated on the LCD). Repeatedly press

the "RANGE" button

7

to cycle through the available ranges,

stopping once the desired range is reached.

2. To return to auto-ranging mode, press and hold the "RANGE"

button

7

for more than one second ( is reactivated).

ENGLISH

FUNCTION BUTTONS

"REL" (RELATIVE) BUTTON

Relative measurements are available for Voltage, Current,

Resistance, Temperature and Capacitance.

1. Perform first measurement.

2. With test leads connected, press REL

8

to set frame of reference.

3. Perform second measurement. The value displayed is the

difference between first and second measurements.

"MAX/MIN" BUTTON

When the "MAX/MIN" button

9

is pressed, the meter keeps track

of the minimum and maximum value of the measurement as the

meter continues to take samples.

1. When measuring, press MAX/MIN

9

and the meter displays the

maximum value. If a new maximum occurs, the display updates

with that new value. Pressing again reveals the minimum value.

If a new minimum occurs, the display updates with the new

value.

2. Press MAX/MIN

9

and hold for more than one second to return

to normal measuring mode.

MM700-1390112ART.indd 8 9/21/2015 2:44:48 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

9

FUNCTION BUTTONS

"REL" (RELATIVE) BUTTON

Relative measurements are available for Voltage, Current,

Resistance, Temperature and Capacitance.

1. Perform first measurement.

2. With test leads connected, press REL

8

to set frame of reference.

3. Perform second measurement. The value displayed is the

difference between first and second measurements.

"MAX/MIN" BUTTON

When the "MAX/MIN" button

9

is pressed, the meter keeps track

of the minimum and maximum value of the measurement as the

meter continues to take samples.

1. When measuring, press MAX/MIN

9

and the meter displays the

maximum value. If a new maximum occurs, the display updates

with that new value. Pressing again reveals the minimum value.

If a new minimum occurs, the display updates with the new

value.

2. Press MAX/MIN

9

and hold for more than one second to return

to normal measuring mode.

MM700-1390112ART.indd 9 9/21/2015 2:44:48 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

10

OPERATING INSTRUCTIONS

AC/DC VOLTAGE (LESS THAN 1000V)

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

the V

setting.

NOTE: The meter defaults to AC measurement. To measure DC, press

the "SEL" button

11

to toggle between AC and DC modes. The AC or

DC icon on the LCD indicates which mode is selected.

2. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

NOTE: If "–" appears on the LCD, the test leads are being applied to

the circuit in reverse. Swap the position of the leads to correct this.

NOTE: When in a voltage setting and the test leads are open,

readings of order mV may appear on the display. This is noise and

is normal. By touching the test leads together to close the circuit

the meter will measure zero volts.

AC/DC LO Z VOLTAGE (LESS THAN 600V)

Voltage measurements in Low Impedance (Lo Z) setting can be used

to identify ghost or stray voltages.

• Follow same procedure for measuring AC/DC Voltage (see above)

with Function Selector switch

2

in the Lo Z setting.

DO NOT attempt to measure voltages greater than 600V in

Lo Z setting.

ENGLISH

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Do not test if leads are improperly seated. Results could cause

intermittent display readings. To ensure proper connection, firmly

press leads into the input jack completely. Lead guard should be

flush with the meter’s faceplate.

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CAT III / CAT IV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

PRESS

NO GAP

5/32"

(4 mm)

.7" (18 mm)

MM700-1390112ART.indd 10 9/21/2015 2:44:49 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

11

OPERATING INSTRUCTIONS

AC/DC VOLTAGE (LESS THAN 1000V)

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

the V

setting.

NOTE: The meter defaults to AC measurement. To measure DC, press

the "SEL" button

11

to toggle between AC and DC modes. The AC or

DC icon on the LCD indicates which mode is selected.

2. Apply test leads to the circuit to be tested to measure voltage.

The meter will auto-range to display the measurement in the

most appropriate range.

NOTE: If "–" appears on the LCD, the test leads are being applied to

the circuit in reverse. Swap the position of the leads to correct this.

NOTE: When in a voltage setting and the test leads are open,

readings of order mV may appear on the display. This is noise and

is normal. By touching the test leads together to close the circuit

the meter will measure zero volts.

AC/DC LO Z VOLTAGE (LESS THAN 600V)

Voltage measurements in Low Impedance (Lo Z) setting can be used

to identify ghost or stray voltages.

• Follow same procedure for measuring AC/DC Voltage (see above)

with Function Selector switch

2

in the Lo Z setting.

DO NOT attempt to measure voltages greater than 600V in

Lo Z setting.

Red leadBlack lead

5/32"

(4 mm)

.7" (18 mm)

MM700-1390112ART.indd 11 9/21/2015 2:44:50 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

12

ENGLISH

OPERATING INSTRUCTIONS

AC/DC CURRENT

NOTE: The meter defaults to AC measurement. To measure DC, press

the "SEL" button

11

to toggle between AC and DC modes. The AC

DC icon on the LCD indicates which mode is selected.

1. Attach test leads to the appropriate jacks and rotate function

selector switch

2

to the appropriate setting as follows:

• For AC/DC currents >400mA and <10A: Insert RED test lead into

10A jack

3

, and BLACK test lead into COM jack

4

, and rotate

function selector switch

2

to the 10A AC/DC setting.

• For mA AC/DC currents <400mA: Insert RED test lead into

mA/µA jack

6

, and BLACK test lead into COM jack

4

, and

rotate function selector switch

2

to the mA AC/DC setting.

• For µA DC currents <400µA: Insert RED test lead into

μA/mA jack

6

, and BLACK test lead into COM jack

4

, and

rotate function selector switch

2

to the µA AC/DC setting.

Red lead Black lead

Black leadRed lead

MM700-1390112ART.indd 12 9/21/2015 2:44:52 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

13

1.

2. To measure current: Remove power from circuit, open circuit at

measurement point, connect meter in-series in the circuit using

the test leads, and apply power to circuit.The meter will auto-

range to display the measurement in the most appropriate range.

Do not attempt to measure more than 10A.

When measuring currents greater than 6A, a measurement

time of 30 seconds followed by 10 minutes of recovery time

is recommended.

CONTINUITY

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead

into COM jack

4

,

and rotate function selector switch

2

to the

Continuity/Resistance/Diode/Capacitance setting.

NOTE: The meter defaults to Continuity testing in this mode. Ensure

that the Continuity Testing icon is visible on the display. If not,

press the "SEL" button

11

until the icon appears.

2. Remove power from circuit.

3. Test for continuity by connecting conductor or circuit with test

leads. If resistance is measured less than 50Ω, an audible signal

will sound and display will show a resistance value indicating

continuity. If circuit is open, display will show "OL".

OPERATING INSTRUCTIONS

DO NOT attempt to measure continuity on a live circuit.

RESISTANCE MEASUREMENTS

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead

into COM jack

4

,

and rotate function selector switch

2

to the

Continuity/Resistance/Diode/Capacitance setting.

NOTE: The meter defaults to Continuity testing in this mode. To

enter Resistance testing mode, press the "SEL" button

11

once.

The Resistance icon will appear on the display.

2. Remove power from circuit.

3. Measure resistance by connecting test leads to circuit. The

meter will auto-range to display the measurement in the most

appropriate range.

Red leadBlack lead

OPERATING INSTRUCTIONS

AC/DC CURRENT

NOTE: The meter defaults to AC measurement. To measure DC, press

the "SEL" button

11

to toggle between AC and DC modes. The AC

DC icon on the LCD indicates which mode is selected.

1. Attach test leads to the appropriate jacks and rotate function

selector switch

2

to the appropriate setting as follows:

• For AC/DC currents >400mA and <10A: Insert RED test lead into

10A jack

3

, and BLACK test lead into COM jack

4

, and rotate

function selector switch

2

to the 10A AC/DC setting.

• For mA AC/DC currents <400mA: Insert RED test lead into

mA/µA jack

6

, and BLACK test lead into COM jack

4

, and

rotate function selector switch

2

to the mA AC/DC setting.

• For µA DC currents <400µA: Insert RED test lead into

μA/mA jack

6

, and BLACK test lead into COM jack

4

, and

rotate function selector switch

2

to the µA AC/DC setting.

MM700-1390112ART.indd 13 9/21/2015 2:44:53 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

14

ENGLISH

NOTE: When in a Resistance setting and the test leads are open

(not connected across a resistor), or when a failed resistor is under

test, the display will indicate O.L. This is normal.

DO NOT attempt to measure resistance on a live circuit.

OPERATING INSTRUCTIONS

DIODE TEST

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead

into COM jack

4

,

and rotate function selector switch

2

to the

Continuity/Resistance/Diode/Capacitance setting.

NOTE: The meter defaults to Continuity testing in this mode. To

enter Diode testing mode, press the "SEL" button

11

twice. The

Diode icon will appear on the display.

2. Touch test leads to diode. A reading of 200-700mV on display

indicates forward bias, "OL" indicates reverse bias. An open

device will show "OL" in both polarities. A shorted device will

show approximately 0mV.

Red leadBlack lead

MM700-1390112ART.indd 14 9/21/2015 2:44:54 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

15

OPERATING INSTRUCTIONS

CAPACITANCE

1. Insert RED test lead into VΩ jack

5

, and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Continuity/Resistance/Diode/Capacitance setting.

NOTE: The meter defaults to Continuity testing in this mode. To

enter Diode testing mode, press the "SEL" button

11

three times.

The Diode icon will appear on the display.

2. Remove power from circuit.

3. Measure capacitance by connecting test leads across the

capacitor. The meter will auto-range to display the measurement

in the most appropriate range.

FREQUENCY / DUTY-CYCLE

1. Insert RED test lead into VΩ jack

5

and BLACK test lead into

COM jack

4

, and rotate function selector switch

2

to the

Frequency/Duty-Cycle setting.

NOTE: The meter defaults to Frequency testing in this mode. To enter

Duty-Cycle testing mode, press the "SEL" button

11

once. Ensure

that the appropriate icon (either

Hz

or

%

) appears on the display.

2. Measure by connecting test leads across the circuit.

Red leadBlack lead

MM700-1390112ART.indd 15 9/21/2015 2:44:56 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

16

ENGLISH

OPERATING INSTRUCTIONS

TEMPERATURE

1. Insert K-type thermocouple with adapter into the VΩ

5

and COM

4

jacks (observe polarity markings on thermocouple and meter), and

rotate function selector switch

2

to the Temperature setting.

NOTE: The meter defaults to Fahrenheit scale in this mode. To enter

Celsius scale, press the "SEL" button

11

once. Ensure that the

appropriate icon (either

°F

or

°C

) appears on the display. Default

temperature scale may be changed by powering on the meter with

the "HOLD" button

11

depressed.

2. To measure temperature, make contact between the

thermocouple tip and the object being measured. When

thermocouple tip and object are in thermal equilibrium, the

measurement on the display will stabilize. The meter will auto-

range to display the measurement in the most appropriate range.

Remove thermocouple before switching meter to other

measurement functions.

The thermocouple included with the original purchase

is suitable for temperatures below 356°F / 180°C only. To

measure higher temperatures, a K-type thermocouple

with the appropriate measurement range should be used.

BAR GRAPH

The Bar Graph is an analog representation of the measurement. It responds

to the measurement approximately 3-5 times faster than the digits in the

digital display which, in certain circumstances, may allow the user to have

a clearer view of quick changes in the property being measured. In any

given range the bar graph scales from zero on the left hand side to the

maximum value of the range on the right hand side of the display.

Bar graph

RED

BLACK

K-Type

Thermocouple

with Adapter

Probe

Adapter

MM700-1390112ART.indd 16 9/21/2015 2:44:57 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

17

MAINTENANCE

BATTERY REPLACEMENT

When indicator is displayed on LCD, batteries must be replaced.

1. Remove screw from battery/fuse door.

2. Replace 2 x AAA batteries (note proper polarity).

3. Replace battery/fuse door and fasten securely with screw.

FUSE REPLACEMENT

A fuse may blow if more than 500mA is applied to the

μA/mA

jack

6

,

or more than 10A is applied to the 10A jack

3

. To access fuses:

1. Remove screw from battery/fuse door.

2. Replace blown fuse(s) with:

A/mA jack

6

:

500mA/1000V fast-blow (Klein Cat. No. 69035)

10A jack

3

: 10A/1000V fast-blow (Klein Cat. No. 69034)

3. Replace battery/fuse door and fasten securely with screw.

T

o avoid risk of electric shock, disconnect leads from any voltage

source before removing battery/fuse door.

To avoid risk of electric shock, do not operate meter while

battery/fuse door is removed.

OPERATING INSTRUCTIONS

TEMPERATURE

1. Insert K-type thermocouple with adapter into the VΩ

5

and COM

4

jacks (observe polarity markings on thermocouple and meter), and

rotate function selector switch

2

to the Temperature setting.

NOTE: The meter defaults to Fahrenheit scale in this mode. To enter

Celsius scale, press the "SEL" button

11

once. Ensure that the

appropriate icon (either

°F

or

°C

) appears on the display. Default

temperature scale may be changed by powering on the meter with

the "HOLD" button

11

depressed.

2. To measure temperature, make contact between the

thermocouple tip and the object being measured. When

thermocouple tip and object are in thermal equilibrium, the

measurement on the display will stabilize. The meter will auto-

range to display the measurement in the most appropriate range.

Remove thermocouple before switching meter to other

measurement functions.

The thermocouple included with the original purchase

is suitable for temperatures below 356°F / 180°C only. To

measure higher temperatures, a K-type thermocouple

with the appropriate measurement range should be used.

BAR GRAPH

The Bar Graph is an analog representation of the measurement. It responds

to the measurement approximately 3-5 times faster than the digits in the

digital display which, in certain circumstances, may allow the user to have

a clearer view of quick changes in the property being measured. In any

given range the bar graph scales from zero on the left hand side to the

maximum value of the range on the right hand side of the display.

500mA/1000V fast-blow fuse

(Klein Cat. No. 69035) 10A/1000V fast-blow fuse

(Klein Cat. No. 69034)

MM700-1390112ART.indd 17 9/21/2015 2:44:58 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

ENGLISH

CLEANING

Be sure meter is turned off and wipe with a clean, dry lint-free

cloth.

Do not use abrasive cleaners or solvents.

STORAGE

Remove the batteries when meter is not in use for a prolonged

period of time. Do not expose to high temperatures or

humidity. After a period of storage in extreme conditions

exceeding the limits mentioned in the General Specifications

section, allow the meter to return to normal operating

conditions before using.

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash.

Items must be properly disposed of in accordance with local

regulations. Please see www.epa.gov or www.erecycle.org

for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.

450 Bond Street

Lincolnshire, IL 60069

1-877-775-5346

[email protected]

www.kleintools.com

ESPAÑOL

MM700-1390112ART.indd 18 9/21/2015 2:44:58 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

MANUAL DE INSTRUCCIONES

ESPAÑOL

MM700

1000 V

10 A

40 M

Ω

• RETENCIÓN DE

DATOS Y RANGO

• BAJA IMPEDANCIA

• CONTINUIDAD POR

INDICADOR AUDIBLE

• MÁX./MÍN./RELATIVO

• TEMPERATURA

• PRUEBA DE DIODO

• CAPACITANCIA Y

FRECUENCIA

Multímetro digital de

rangoautomático

True RMS

Tecnología de

medición

MM700-1390112ART.indd 19 9/21/2015 2:45:01 PM

Dwg Name: MM700-1390112ART

Dwg No: 1390112

ECO No: 20617 Rev: E

Pkg Dwg Ref: 1290186

Color Reference: N/A

20

ESPECIFICACIONES GENERALES

Klein Tools MM700 es un multímetro digital de rango automático con

media cuadrática real (TRMS) que mide voltaje CA/CD, corriente CA/CD y

resistencia. También sirve para medir temperatura, capacitancia, frecuencia

y ciclo de servicio, y para probar diodos y continuidad.

• Altitud de funcionamiento: 6562pies (2000m)

• Humedad relativa: <90% sin condensación

• Temperatura de operación: 14°F a 122°F (-10°C a 50°C)

• Temperatura de almacenamiento: -4°F a 140°F (-30°C a 60°C)

• Precisión: valores establecidos según una temperatura ambiente

de 65°F a 83°F (18°C a 28°C)

• Coeciente de temperatura: 0,1 × (precisión indicada) por cada

°C por encima de los 28°C o por debajo de los 18°C, es necesario

realizar correcciones si la temperatura del ambiente de trabajo se

encuentra fuera del rango de precisión de temperatura

• Dimensiones:

7,02" × 3,54" × 2,10" (178,3mm × 89,9mm × 53,3mm)

• Peso: 14,6 oz (414 g)

• Calibración: precisa durante un año

• Normas: Cumple con: UL STD 61010-1, 61010-2-030,

61010-2-033.

Certificado según las normas:

CSA C22.2 STD N.° 61010-1,

61010-2-030, 61010-2-033.

IEC EN 61010-1, 61010-2-030,

61010-2-033, 61326-1.

• Grado de contaminación: 2

• Precisión: ± (% de lectura + cantidad de dígitos menossignificativos)

• Protección ante caídas: 6,6pies (2m)

• Protección contra el ingreso de objetos sólidos y líquidos:

IP42 (excepto para los conectores de cables de

prueba, consulte la sección ADVERTENCIAS)

• Clasicación de seguridad:

CAT IV 600V, CAT III 1000V, clase2,

doble aislamiento

CAT III: La categoría III de medición es aplicable a los circuitos de

medición y prueba conectados a la distribución de la instalación de

suministro eléctrico de un edificio.

CAT IV: La categoría IV de medición es aplicable a los circuitos

de medición y prueba conectados a la fuente de la instalación de

suministro eléctrico de un edificio.

• Entorno electromagnético: IEC EN 61326-1. Este equipo

cumple con los requisitos apropiados para su uso en entornos

electromagnéticos básicos y controlados como propiedades

residenciales, establecimientos comerciales e instalaciones de

industria ligera.

Especificaciones sujetas a cambios.

ESPAÑOL

RESISTENCIA (RANGO AUTOMÁTICO)

Función Resolución

Precisión

400,0Ω 0,1Ω

± (1,5% + 5 dígitos)

4,000kΩ 1Ω

40,00kΩ 10Ω

400,0kΩ 100Ω

4,000MΩ 1kΩ ± (2,0% + 10 dígitos)

40,00MΩ 10kΩ

Entrada máxima: 600V CD o 600V CA RMS

MM700-1390112ART.indd 20 9/21/2015 2:45:01 PM

La page charge ...

Klein Tools MM600 Manuel utilisateur

Klein Tools MM600 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents