Fortin EVO 107861 Guide d'installation

Taper
Guide d'installation
* HOOD PIN HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED
IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN,
SET FUNCTION A11 TO OFF.
CONTACT
DE CAPOT
MANDATORY INSTALL | INSTALLATION OBLIGATOIRE Notice: the installation of safety
elements are mandatory. The hood pin
is an essential security element and
must be installed.
Notice: l'installation des éléments de
sécurité est obligatoire. Le contact de
capot est un élément de sécurité
essentiel et doit absolument être
installé.
THIS MODULE MUST BE INSTALLED BY A
QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT
DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR
UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS
PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.
STATUT DE CAPOT : LE CONTACT DE CAPOT, DOIT ÊTRE INSTALLÉ SI LE
VÉHICULE PEUT DÉMARRER À DISTANCE, LORSQUE LE CAPOT EST OUVERT,
PROGRAMMEZ LA FONCTION A11 À NON.
A11 OFF
NON
ADDENDUM - SUGGESTED WIRING CONFIGURATION
ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
ALL REV.: 20231005 Guide # 107861
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule sup-
pores dans ce diagramme (fonctionnelles si équipé)
VEHICLE
VEHICULES
YEARS
ANNÉES
Immobilizer bypass
Lock
Unlock
Trunk (open)
RAP shutdown
Rear Defrost (AUX.1)
Tachometer
Door Status
Trunk Status
Hand-Brake Status
Foot-Brake Status
OEM Remote monitoring**
NISSAN
Versa
2022-2023
MODEL: EVO-ALL
DATE:02/2019
FORTIN.CA
SN: 000000 00000
MADE IN CANADA
© 2018 ALL RIGHTS RESERVED
2019
COMPATIBLE
MODULE
REQUIRED:
QR CODE
ON THE LABEL FIRMWARE VERSION
VERSION LOGICIELLE
To add the rmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.
Pour ajouter la version logicielle et les options,
utilisez l’outil FLASH LINK UPDATER
ou FLASH LINK MOBILE, vendu séparément.
MANUFACTURED
AFTER: 2019
MODULE
COMPATIBLE
REQUIS:
CODE QR SUR
LÉTIQUETTE 72.[54]
FABRIQUÉ APRÈS:
2019 MINIMUM
IF THE VEHICLE IS NOT EQUIPPED
WITH FUNCTIONAL HOOD PIN:
SI LE VÉHICULE N’EST PAS ÉQUIPÉ
D’UN CONTACT DE CAPOT FONCTIONNEL:A11 OFF
NON
Hood trigger (Output Status).
Contact de capot (état de sortie).
Parts required (Not included) Pièce(s) requise(s) (Non incluse(s))
1x Relay (Trunk release) 1x Relai (Ouverture de la valise)
Program bypass option:
Programmez l’option du contournement:
UNIT OPTION
OPTION UNITE DESCRIPTION
C1
OEM Remote status (Lock/Unlock)
monitoring
Suivi des status (Verrouillage/Déverrouil-
lage) de la télécommande d’origine
NOTES
**
The vehicles OEM remote will not be
operable during remote start.
La télécommande d’origine du véhicule ne sera pas fonctionnelle
durant le démarrage à distance.
Page 1 / 9
REGULAR INSTALLATION
INSTALLATION RÉGULIÈRE
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DESCRIPTION | DESCRIPTION
BCM Ignition switch
Commutateur d’ignition
2
2
1
(~)CAN HIGH (~)CAN LOW
(+)IGNITION
(+)STARTER
(+)ACCESORY
(+)12V
(+)TRUNK
Clutch switch
Commutateur d’embrayage
3
(+) CLUTCH
Page 2 / 9
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Yellow In A1
Purple In A2
Purple/White In A3
Green Out A4
White Out A5
Orange In A6
Orange/Black In A7
Dk.Blue In A8
Red/Blue In A9
Lt.Blue/Black A10
Black Out A11
Pink Out A12
Yellow/Black In A13
Brown/White Out A14
Pink/Black Out A15
Purple/Yellow A16
Green/White A17
Green/Red A18
White/Black A19
Lt.Blue A20
C5 Brown
C4 Gray/Black
C3 Gray
C2 Orange/Brown
C1 Orange/Green
D6 White/Red
D5 White/Blue
D4 White/Green
D3 Yellow/Red
D2 Yellow/Blue
D1 Yellow/Green
AC
D
AUTOMATIC TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION AUTOMATIQUE
CAN LOW
CAN HIGH
WITH | AVEC DATA-LINK:
ALWAYS REQUIRED
TOUJOURS REQUIS
NOT REQUIRED WITH
DATALINK
NON REQUIS EN
DATA-LINK
12V BATTERY
Ground | Masse
B
REMOTE
STARTER
DÉMARREUR
À DISTANCE
WITH | AVEC DATA-LINK:
Direct connection
Branchement directe
HOOD IN RS8
(-)
HAND BRAKE IN RS9
(-)
TRUNK RELEASE
(-) OUT RS11
(+/-) IN RS12
TACHOMETER
F
OOT
B
RAKE
(+)
IN RS13
AUXILLIAIRE1
(-) OUT RS16
GROUND OUT WHILE RUNNING
(-) OUT RS14
TRUNK
(-)
IN RS17
DOOR
(-) IN RS18
UNLOCK
(-) OUT RS19
LOCK
(-) OUT RS20
A15
A14
A12
A6
A11
A8
A5
A4
A3
A2
Ground | Masse
(-)
RS1
12V BATTERY
RS2 IN
(+)
ACCESSORY
RS5 OUT (+)
IGNITION
RS6 IN/OUT (+)
STARTER
RS7 OUT (+)
(-) Hood Status
(-) Hand Brake
(-/+) Tachometer
(+) Foot Brake
(-) Ground While Running
(-) Auxilliaire1
(-) Trunk Status
(-) Door Status
(-) Unlock
(-) Lock
(+) Ignion
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
C5
C4
C3
C2
C1
D6
D5
D4
D3
D2
D1
A1
D1
D4
D5
D6
C1
C2
C5
A20
A19
A18
A17
A16
A13
A10
A9
A7
VERSA
Ignition switch -
Black 4-Pin Connector
- Back vue
Commutateur
d’ignition -
Connecteur Noir de
4-Pins Vue de dos
1
3
2
4
1
(+)ACCESSORY (+)IGNITION(+)12V
Blue
Bleu
Red
Rouge
Green
Vert
1
23
(~)CAN HIGH (~)CAN LOW
BCM - Black
40-Pin
Connector -
Back vue
BCM -
Connecteur
Noir de 40-Pin -
Vue de dos
12345678101116
17
18 14
15
212223242526282930313233353637383940
1920
27
13 12 9
34
Pink
Rose
Blue
Bleu
2
2A
A
2B
(+)TRUNK
Purple/Blue
Mauve/Bleu
1
11
12
2
34
678910
BCM white 12-Pin Connector Back vue
* If equipped with electric trunk
BCM Connecteur blanc de 12-Pins
Vue de dos
* Si équipé de valise électrique
2B
5
(+)STARTER
Yellow
Jaune
30
86
85
87
87a Fuse
Fusible
RS5 RS2
A1
A1/RS6
A13
C3 C430
30
86
85
87
87a
87/85
30
86
85
87
87a
RS7
Page 3 / 9
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
Yellow In A1
Purple In A2
Purple/White In A3
Green Out A4
White Out A5
Orange In A6
Orange/Black In A7
Dk.Blue In A8
Red/Blue In A9
Lt.Blue/Black A10
Black Out A11
Pink Out A12
Yellow/Black In A13
Brown/White Out A14
Pink/Black Out A15
Purple/Yellow A16
Green/White A17
Green/Red A18
White/Black A19
Lt.Blue A20
C5 Brown
C4 Gray/Black
C3 Gray
C2 Orange/Brown
C1 Orange/Green
D6 White/Red
D5 White/Blue
D4 White/Green
D3 Yellow/Red
D2 Yellow/Blue
D1 Yellow/Green
AC
D
MANUAL TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION MANUELLE
CAN LOW
CAN HIGH
WITH | AVEC DATA-LINK:
ALWAYS REQUIRED
TOUJOURS REQUIS
NOT REQUIRED WITH
DATALINK
NON REQUIS EN
DATA-LINK
12V BATTERY
Ground | Masse
B
REMOTE
STARTER
DÉMARREUR
À DISTANCE
WITH | AVEC DATA-LINK:
Direct connection
Branchement directe
HOOD IN RS8
(-)
HAND BRAKE IN RS9
(-)
TRUNK RELEASE
(-) OUT RS11
(+/-) IN RS12
TACHOMETER
F
OOT
B
RAKE
(+)
IN RS13
AUXILLIAIRE1
(-) OUT RS16
GROUND OUT WHILE RUNNING
(-) OUT RS14
TRUNK
(-)
IN RS17
DOOR
(-) IN RS18
UNLOCK
(-) OUT RS19
LOCK
(-) OUT RS20
A15
A14
A12
A6
A11
A8
A5
A4
A3
A2
Ground | Masse
(-)
RS1
12V BATTERY
RS2 IN
(+)
ACCESSORY
RS5 OUT (+)
IGNITION
RS6 IN/OUT (+)
STARTER
RS7 OUT (+)
STARTER2
RS7b OUT (+)
a 1
(-) Hood Status
(-) Hand Brake
(-/+) Tachometer
(+) Foot Brake
(-) Ground While Running
(-) Auxilliaire1
(-) Trunk Status
(-) Door Status
(-) Unlock
(-) Lock
(+) Ignion
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
C5
C4
C3
C2
C1
D6
D5
D4
D3
D2
D1
A1
D1
D4
D5
D6
C1
C2
C5
A20
A19
A18
A17
A16
A13
A10
A9
A7
VERSA
Ignition switch -
Black 4-Pin Connector
- Back vue
Commutateur
d’ignition -
Connecteur Noir de
4-Pins Vue de dos
1
3
2
4
1
(+)ACCESSORY (+)IGNITION(+)12V
Blue
Bleu
Red
Rouge
Green
Vert
1
23
(~)CAN HIGH (~)CAN LOW
BCM - Black
40-Pin
Connector -
Back vue
BCM -
Connecteur
Noir de 40-Pin -
Vue de dos
12345678101116
17
18 14
15
212223242526282930313233353637383940
1920
27
13 12 9
34
Pink
Rose
Blue
Bleu
2
2A
A
2B
(+)TRUNK
Purple/Blue
Mauve/Bleu
1
11
12
2
34
678910
BCM white 12-Pin Connector Back vue
* If equipped with electric trunk
BCM Connecteur blanc de 12-Pins
Vue de dos
* Si équipé de valise électrique
2B
5
(+)STARTER
Yellow
Jaune
Clutch switch -
white 4-Pin
Connector - Back
vue
Commutateur
d’embrayage
Connecteur Blanc
de 4-Pins - Vue
de dos
3
1
3
2
4
(+)CLUTCH
Purple
Mauve
30
86
85
87
87a Fuse
Fusible
RS5 RS2
A1
A1/RS6
A13
C3 C430
30
86
85
87
87a
87/85
30
86
85
87
87a
RS7a RS7b
Page 4 / 9
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
DCRYPTOR PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION AVEC DCRYPTOR
Parts required (not included) Pièces requises (non incluses)
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
1x FLASH LINK MOBILE
1x FLASH LINK MOBILE APP
SOFTWARE | PROGRAMME
Smartphone Android or iOS with Internet connection
(Internet provider charges may apply)
Téléphone Intelligent Android ou iOS avec connection
Internet (des frais du fournisseur Internet peuvent s’appliquer)
OR
OU
Microsoft Windows Computer with Internet connection
Ordinateur Microsoft Windows avec connection Internet
1x1x
BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE. | AVANT LA PROGRAMMATION CONFIGURER LES OPTIONS DE L'UNITÉ ET SAUVEGARDER.
5-Prog.1-17_VERSA_KEY_P1-3
x1
HOLD
Press and hold
Insert
the
programming button:
the 4-Pin (Data-Link)
connector.
Appuyez maintenir
enfoncé
Insérez
et
le bouton de
programmation:
le connecteur 4 pins
(Data-Link)
The Blue, Red, Yellow and
Blue & Red LEDs will
alternatively illuminate.
Les DELs Bleue, Rouge,
Jaune et Bleue & Rouge
s'allumeront alternativement.
RELEASE
If the LED is not solid BLUE
disconnect the 4-Pin connector
(Data-Link) and go back to step 1.
ON BLUE
BLEU
Si le DEL n'est pas BLEU
débranchez le connecteur 4
pins (Data-Link) et allez au
début de l'étape 1.
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
4
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
The BLUE LED will turn
OFF.
La DEL BLUE s'éteindra.
The BLUE LED will flash
rapidly.
La DEL BLEU clignotera
rapidement.
IGNITION ON
IGNITION OFF
ON OFF
WAIT
Release the programming
button when the LED is BLUE. Relâchez le bouton de
programmation quand la DEL
est BLEU.
2
1
3
Insert the required remaining
connectors. Insérez les connecteurs
requis restants.
LOCK
IGN
TURN
ON/RUN
Turn the key to the ON/RUN
position. Tournez la clé à la position
ON/RUN.
Wait, Attendre,
Page 5 / 9
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 2/3 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 2/3
5-Prog.1-17_VERSA_KEY_P2-3
5
6
7
8
9
CONTINUED NEXT PAGE | CONTINUEZ À LA PAGE SUIVANTE
The YELLOW LED will turn
ON.
The RED LED will flash
once.
La DEL JAUNE s'allumera.
La DEL ROUGE clignotera
une fois.
The YELLOW LED will turn
ON.
The RED LED will flash
once.
La DEL JAUNE s'allumera.
La DEL ROUGE clignotera
une fois.
The YELLOW LED will turn
OFF.
La DEL JAUNE s'éteindra.
The Red and Yellow LEDs
will start flashing alternatively.
Les DELs Rouge et Jaune
clignoteront alternativement.
The RED LED will turn ON. La DEL ROUGE
s'allumera.
IGNITION ON
IGNITION OFF
ON
WAIT
IGNITION ON
WAIT
IGNITION ON
IGNITION OFF
OFF
WAIT
IGNITION ON
ON
WAIT
ALTERNATE
LOCK
IGN
TURN
ON/RUN
LOCK
IGN
TURN
ON/RUN
Turn the key to the ON/RUN
position. Tournez la clé à la position
ON/RUN.
Turn the key to the ON/RUN
position. Tournez la clé à la position
ON/RUN.
Turn the ignition to the OFF
position.
Tournez la clé à la position ARRÊT
(OFF).
LOCK
START
OFF
TURN
OFF
Turn the ignition to the OFF
position.
Tournez la clé à la position ARRÊT
(OFF).
LOCK
START
OFF
TURN
OFF
Turn the ignition to the OFF
position.
Tournez la clé à la position ARRÊT
(OFF).
LOCK
START
OFF
TURN
OFF
Page 6 / 9
The DCryptor process can
take up to 15 minutes. Le processus du DCryptor
peut prendre jusqu'à 15
minutes.
EVO-ALL
Disconnect all the connectors and after
the Data-Link (4-pins) connector.
Débranchez tous les connecteurs et ensuite
le connecteur Data-Link (4-pins).
*Pièces requises (non incluses)
Use the tool:
FLASH LINK UPDATER or
FLASH LINK MOBILE
to visit the DCryptor menu.
Utilisez l'outil:
FLASH LINK UPDATER ou
FLASH LINK MOBILE
pour visiter le menu DCryptor.
*Parts required (not included)
FLASH LINK UPDATER*
FLASH LINK MOBILE*
FLASH LINK MANAGER*
SOFTWARE | PROGRAMME
Microsoft Windows
Computer with
Internet connection*
Ordinateur Microsoft
Windows avec
connection Internet*
VEHICLE'S OBDII
CONNECTOR
CONNECTEUR OBDII
DU VÉHICULE
OR
OU
Smartphone*
(Internet provider
charges
may apply)
Téléphone
Intelligent*
(des frais du
fournisseur
Internet peuvent
s’appliquer)
AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link)
connector and after, all the remaining connector.
APRÈS LA PROCÉDURE DE PROGRAMMATION
DCRYPTOR COMPLETÉE : retournez au véhicule et
rebranchez le connecteur 4-pins (Data-Link)
et après, tous les connecteurs du EVO-ALL.
EVO-ALL
10
11
12
REMOTE STARTER / ALARM VERIFICATION
PROCEDURE | PROCÉDURE DE VÉRIFICATION
DU DÉMARREUR À DISTANCE / ALARME
Test the remote starter. Remote start the vehicle.
Testez le démarreur à distance. Démarrez le véhicule
à distance.
The module is now programmed.
Le module est programmé.
REMOTE STARTER / ALARM VERIFICATION
PROCEDURE | PROCÉDURE DE VÉRIFICATION
DU DÉMARREUR À DISTANCE / ALARME
Test the remote starter. Remote start the vehicle.
Testez le démarreur à distance. Démarrez le véhicule
à distance.
The module is now programmed.
Le module est programmé.
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
KEY BYPASS PROGRAMMING PROCEDURE 3/3 | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ 3/3
5-Prog.1-17_VERSA_KEY_P3-3
Page 7 / 9
Remote start the
vehicle.
Démarrez à
distance.
All doors must
be closed.
Toutes les
portes doivent
être fermées.
Start
UNLOCK
Unlock the doors with
the remote-starter
remote.
Déverrouillez les portes
avec la télécomande du
démarreur à distance.
Insert and Turn
the key to the
Ignition ON/RUN
position.
Insérez et
tournez la clé à
la position
"ON/RUN".
The vehicle can
now be put in to
gear and driven.
Vous êtes
maintenant prêt à
embrayer et
prendre la route.
Press
the brake pedal.
Appuyez
sur la pédale de
frein.
ON
TURN
ON/RUN
This guide may change without notice. See www.fortin.ca for latest version.
Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version.
REMOTE STARTER FUNCTIONALITY | FONCTIONNALITÉS DU DÉMARREUR À DISTANCE
Page 8 / 9
ALL
MODEL: EVO-ALL
DATE:02/2019
FORTIN.CA
SN: 000000 00000
MADE IN CANADA
© 2018 ALL RIGHTS RESERVED
Module label | Étiquette sur le module
Notice: Updated Firmware and Installation Guides
Updated rmware and installation guides are posted on our web site on a regular
basis. We recommend that you update this module to the latest rmware and
download the latest installation guide(s) prior to the installation of this product.
Notice: Mise à jour microprogramme et Guides d’installations
Des mises à jour du Firmware (microprogramme) et des guides d’installation
sont mis en ligne régulièrement. Vérifi ez que vous avez bien la dernière version
logiciel et le dernier guide d’installation avant l’installation de ce produit.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe
logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case
is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability
or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other
way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be
installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without
notice. Visit www.fortinbypass.com to get the latest version.
MISE EN GARDE
L’information de ce guide est fournie sur la base de représentation (telle quelle) sans aucune garantie de précision et
d’exactitude. Il est de la seule responsabilité de l’installateur de vérifi er tous les ls et circuits avant d’effectuer les connexions.
Seuls une sonde logique ou un multimètre digital doivent être utilisés. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume
aucune responsabilité de l’exactitude de l’information fournie. L’installation (dans chaque cas) est la responsabilité de
l’installateur effectuant le travail. FORTIN SYSTÈMES ÉLECTRONIQUES n’assume aucune responsabilité suite à
l’installation, que celle-ci soit bonne, mauvaise ou de n’importe autre type. Ni le manufacturier, ni le distributeur ne se
considèrent responsables des dommages causés ou ayant pu être causés, indirectement ou directement, par ce module,
excepté le remplacement de ce module en cas de défectuosité de fabrication. Ce module doit être installé par un technicien
qualifi é. L’information fournie dans ce guide est une suggestion. Ce guide d’instruction peut faire l’objet de changement
sans préavis. Consultez le www.fortinbypass.com pour voir la plus récente version.
Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE WEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com
Page 9 / 9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Fortin EVO 107861 Guide d'installation

Taper
Guide d'installation

dans d''autres langues