Trendnet TEW-929DRU Manuel utilisateur

Catégorie
La mise en réseau
Taper
Manuel utilisateur
TEW-929DRU User Manual
1. Before You Start
Package Contents
TEW-929DRU
Quick Installation Guide
2 x detachable high gain antennas
Network cable (1.5m / 5 ft.)
RJ-45 to RS-232 console cable (1.5m / 5 ft.)
Power adapter (12V DC, 2A)
Rackmount kit
Minimum Requirements
A computer with a wired or wireless network adapter and web browser
Broadband Internet
Installed modem
Network cable
Optional Equipment
EIA standard 19” rack
2. Quick Reference
Note: By default, the admin password used to login to the router configuration, wireless network name/SSID, and
wireless encryption settings have been pre-configured for your convenience and can be located on the included preset
wireless settings sticker or on the device label located at the bottom of the router. By default, the router web
management configuration page can be accessed from LAN ports 1-3 using the URL http://tew-929dru or using the
default LAN IP address http://192.168.10.1 and WAN1 default configuration is set to DHCP client for Internet
connectivity. You can choose to quickly set up your router and use the pre-configured settings or refer to the next
section for more detailed instructions on initial installation and configuration.
3. Hardware Installation and Configuration
Note: It is recommended that you configure the wireless router from a wired computer.
1. Attach the antennas to the front of the router and position them for the best WiFi coverage. It is recommended that
you position all of the antennas vertically as shown.
2. Connect a network cable from the WAN1 port of your router to your modem.
3. Connect a network cable from one of the LAN ports of your router to your computer.
4. Connect the included power adapter from a power outlet to your router power port and push the Power On (-I) /
Off(o) switch into the On (-) position.
5. The Power, 2.4G, and 5G LEDs will turn on solid indicating that the router is ready.
6. Open your web browser on the connected computer and in the address bar, enter http://tew-9292dru or
http://192.168.10.1 and press Enter to access the router web configuration page.
7. Enter the default User Name and Password, then click Login. By default, the pre-configured user name and password
are located on the included preset wireless settings sticker or device label located on the bottom of the router.
8. To change the administrator password for the router configuration, click Management and click Administration.
Note: By default the administrator password has been pre-configured for your convenience and can be located on the
included wireless settings sticker or on the device label located on the bottom of the router. If you are modifying the
administrator password, you will need to login to the router configuration using the new password.
9. Enter the new administrator password in the Password field and re-type the new password in the Confirmation field.
Click Apply to save and commit the changes.
10. To change your router LAN IPv4 address settings, click on Network and click LAN.
11. Under Common Configuration and General Setup, enter the new LAN IPv4 address and subnet mask in the IPv4
address and IPv4 netmask fields. Click Apply at the bottom of the page to save and commit the changes. Please wait for
the new address settings to be applied and log back into the router web configuration page using the new LAN IPv4
address.
Note: If your computer IP address settings are not automatically updated to the new settings, you may need to manually
renew your computer IP address settings in order for you to log back into the router web configuration with the new
LAN IPv4 address settings.
12. To configure your WAN1 Internet connection settings, click Network and click WAN.
13. Under Common Configuration and General Setup, click the Protocol drop-down list and select the appropriate
protocol (Static address, DHCP client, PPTP, PPPoE, L2TP) for your Internet connection. DHCP client is the typical
protocol in which the connection settings are automatically obtained by your ISP (Internet Service Provider). If you are
unsure about the Internet connection settings, please contact your ISP (Internet Service Provider) for details. After you
have completed the Internet connection settings, click Apply to save and commit the changes.
14. To configure your wireless network name/SSID and wireless encryption settings, click Wireless and click the wireless
band you would like to configure. Wireless 2.4GHz or Wireless 5GHz
Note: By default, the wireless network name/SSID and wireless encryption has been pre-configured for your
convenience and can be located on the included wireless settings sticker or on the device label located on the bottom of
the router. If you are modifying the wireless settings, you will need to connect to the router with your WiFi clients using
the new settings.
15. To change the wireless network name/SSID for the selected wireless band, under Interface Configuration and
General Setup, enter the new name in the ESSID field and click Apply to save and commit the changes.
Note: The wireless network name/SSID is the name your WiFi clients will need to search and discover when connecting
to your router wireless network.
16. To change the wireless encryption key for the selected wireless band, under Interface Configuration and Wireless
Security, enter the new encryption in the Key field and click Apply to save and commit the changes.
Note: WPA3-Personal AES wireless encryption is strongly recommended. By default, WPA3/WPA2-Personal Mixed is
configured for client compatibility. The wireless encryption key is the key your WiFi clients will need to enter when
connecting to your router wireless network.
Note: To download the latest version of the user’s guide, please go to http://www.trendnet.com/support and select the
TEW-929DRU within the Product Download drop-down list.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the users authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device is restricted for indoor use.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 42cm between the radiator & your body.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes au (x) RSS (s) exemptés de
licence d'Innovation, Sciences etveloppement économique Canada. L'opération est soumise aux deux conditions
suivantes:
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable de l'appareil.
This radio transmitter [6337A-TEW929DRU] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain
indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for
any type listed are strictly prohibited for use with this device.
Le présent émetteur radio (6337A-TEW929DRU) a été approuvé par Innovation, Sciences et Développement
économique Canada pour fonctionner avec les types d'antenne énumés ci-dessous et ayant un gain admissible
maximal d'antenne. Les types d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal
indiqué pour tout type listé sont strictement interdits pour une utilisation avec cet appareil.
Ant.
Brand
Model Name
Antenna Type
Gain (dBi)
2.4GHz
5GHz
1
.gear
C732-510012-A
Dipole
5.33
5.88
2
.gear
C732-510012-A
Dipole
5.33
5.88
The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux.
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as
appropriate.
le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz)
doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 26cm between the radiator & your
body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 26 cm de distance entre la source de
rayonnement et votre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Trendnet TEW-929DRU Manuel utilisateur

Catégorie
La mise en réseau
Taper
Manuel utilisateur

dans d''autres langues