Trendnet TEW-929DRU Manuel utilisateur

Marque: Trendnet

Modèle: TEW-929DRU

Catégorie: La mise en réseau

Taper: Manuel utilisateur

TEW-929DRU User Manual

1. Before You Start

Package Contents

• TEW-929DRU

• Quick Installation Guide

• 2 x detachable high gain antennas

• Network cable (1.5m / 5 ft.)

• RJ-45 to RS-232 console cable (1.5m / 5 ft.)

• Power adapter (12V DC, 2A)

• Rackmount kit

Minimum Requirements

• A computer with a wired or wireless network adapter and web browser

• Broadband Internet

• Installed modem

• Network cable

Optional Equipment

• EIA standard 19” rack

2. Quick Reference

Note: By default, the admin password used to login to the router configuration, wireless network name/SSID, and

wireless encryption settings have been pre-configured for your convenience and can be located on the included preset

wireless settings sticker or on the device label located at the bottom of the router. By default, the router web

management configuration page can be accessed from LAN ports 1-3 using the URL http://tew-929dru or using the

default LAN IP address http://192.168.10.1 and WAN1 default configuration is set to DHCP client for Internet

connectivity. You can choose to quickly set up your router and use the pre-configured settings or refer to the next

section for more detailed instructions on initial installation and configuration.

3. Hardware Installation and Configuration

Note: It is recommended that you configure the wireless router from a wired computer.

1. Attach the antennas to the front of the router and position them for the best WiFi coverage. It is recommended that

you position all of the antennas vertically as shown.

2. Connect a network cable from the WAN1 port of your router to your modem.

3. Connect a network cable from one of the LAN ports of your router to your computer.

4. Connect the included power adapter from a power outlet to your router power port and push the Power On (-I) /

Off(o) switch into the On (-) position.

5. The Power, 2.4G, and 5G LEDs will turn on solid indicating that the router is ready.

6. Open your web browser on the connected computer and in the address bar, enter http://tew-9292dru or

http://192.168.10.1 and press Enter to access the router web configuration page.

7. Enter the default User Name and Password, then click Login. By default, the pre-configured user name and password

are located on the included preset wireless settings sticker or device label located on the bottom of the router.

8. To change the administrator password for the router configuration, click Management and click Administration.

Note: By default the administrator password has been pre-configured for your convenience and can be located on the

included wireless settings sticker or on the device label located on the bottom of the router. If you are modifying the

administrator password, you will need to login to the router configuration using the new password.

9. Enter the new administrator password in the Password field and re-type the new password in the Confirmation field.

Click Apply to save and commit the changes.

10. To change your router LAN IPv4 address settings, click on Network and click LAN.

11. Under Common Configuration and General Setup, enter the new LAN IPv4 address and subnet mask in the IPv4

address and IPv4 netmask fields. Click Apply at the bottom of the page to save and commit the changes. Please wait for

the new address settings to be applied and log back into the router web configuration page using the new LAN IPv4

address.

Note: If your computer IP address settings are not automatically updated to the new settings, you may need to manually

renew your computer IP address settings in order for you to log back into the router web configuration with the new

LAN IPv4 address settings.

12. To configure your WAN1 Internet connection settings, click Network and click WAN.

13. Under Common Configuration and General Setup, click the Protocol drop-down list and select the appropriate

protocol (Static address, DHCP client, PPTP, PPPoE, L2TP) for your Internet connection. DHCP client is the typical

protocol in which the connection settings are automatically obtained by your ISP (Internet Service Provider). If you are

unsure about the Internet connection settings, please contact your ISP (Internet Service Provider) for details. After you

have completed the Internet connection settings, click Apply to save and commit the changes.

14. To configure your wireless network name/SSID and wireless encryption settings, click Wireless and click the wireless

band you would like to configure. Wireless 2.4GHz or Wireless 5GHz

Note: By default, the wireless network name/SSID and wireless encryption has been pre-configured for your

convenience and can be located on the included wireless settings sticker or on the device label located on the bottom of

the router. If you are modifying the wireless settings, you will need to connect to the router with your WiFi clients using

the new settings.

15. To change the wireless network name/SSID for the selected wireless band, under Interface Configuration and

General Setup, enter the new name in the ESSID field and click Apply to save and commit the changes.

Note: The wireless network name/SSID is the name your WiFi clients will need to search and discover when connecting

to your router wireless network.

16. To change the wireless encryption key for the selected wireless band, under Interface Configuration and Wireless

Security, enter the new encryption in the Key field and click Apply to save and commit the changes.

Note: WPA3-Personal AES wireless encryption is strongly recommended. By default, WPA3/WPA2-Personal Mixed is

configured for client compatibility. The wireless encryption key is the key your WiFi clients will need to enter when

connecting to your router wireless network.

Note: To download the latest version of the user’s guide, please go to http://www.trendnet.com/support and select the

TEW-929DRU within the Product Download drop-down list.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This device is restricted for indoor use.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 42cm between the radiator & your body.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes au (x) RSS (s) exemptés de

licence d'Innovation, Sciences et Développement économique Canada. L'opération est soumise aux deux conditions

suivantes:

(1) Cet appareil ne doit pas provoquer d'interférences.

(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un

fonctionnement indésirable de l'appareil.

This radio transmitter [6337A-TEW929DRU] has been approved by Innovation, Science and Economic

Development Canada to operate with the antenna types listed below, with the maximum permissible gain

indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for

any type listed are strictly prohibited for use with this device.

Le présent émetteur radio (6337A-TEW929DRU) a été approuvé par Innovation, Sciences et Développement

économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible

maximal d'antenne. Les types d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal

indiqué pour tout type listé sont strictement interdits pour une utilisation avec cet appareil.

Ant.

Brand

Model Name

Antenna Type

Gain (dBi)

2.4GHz

5GHz

Ｍ.gear

C732-510012-A

Dipole

5.33

5.88

Ｍ.gear

C732-510012-A

Dipole

5.33

5.88

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful

interference to co-channel mobile satellite systems.

les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant

les mêmes canaux.

The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the

equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as

appropriate.

le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz)

doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 26cm between the radiator & your

body.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non

contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 26 cm de distance entre la source de

rayonnement et votre corps.

Trendnet TEW-929DRU Manuel utilisateur

Marque: Trendnet

Modèle: TEW-929DRU

Catégorie: La mise en réseau

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Trendnet TEW-929DRU User manual

Trendnet TEW-929DRU Manuel utilisateur

Trendnet TEW-929DRU Manuel utilisateur

dans d''autres langues

Documents connexes