Progress Lighting P250006 Guide d'installation

Ceiling Fan Installation Manual

P250006

93114640_A

Date Pu rchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

109226

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

785247242412

785247240845

Table of Contents

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan .......................................................................................................................................................................

Installing Your Fan ..........................................................................................................................................................................

Attaching the Fan Blades.................................................................................................................................................................

Installing the Decorative Cover.......................................................................................................................................................

Operating Your Transmitter ...........................................................................................................................................................

Care of Your Fan ...........................................................................................................................................................................

Troubleshooting ............................................................................................................................................................................

Specifications ................................................................................................................................................................................

1.

2.

3.

6.

7.

8.

10.

11.

12.

1. Safety Rules

To reduce the risk of electric shock, ensure electricity has been turned off

at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less. Use

only cUL-listed outlet boxes marked “FOR FAN SUPPORT.”

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from

the trailing edge of the blades to the floor.

Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into the outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the

other side of the outlet box.

All set screws must be checked and retightened where necessary before

installation.

Suitable for use with solid-state speed control.1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN

INSTALLING THE BRACKETS, BALANCING THE BLADES OR

CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN –

BETWEEN ROTATING FAN BLADES.

NOTE

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER PERSONAL

INJURY, MOUNT FAN ONLY ON AN OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG)

OR LESS AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET

BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN

DOUBT.

Unpack your fan and check the contents. You should have the following items:

Unpacking Your Fan 2.

12. Loose parts bag containing:

a. Blade attachment hardware

(13 screws, 13 fiber washers)

b. Mounting hardware

Wire nuts (3)

3

4

1

29

5

6

8

7

12

ab

11

10

Set of blades (4)

Mounting bracket

Fan motor assembly

Decorative ring

Decorative cover

Decorative cap

1.

2.

3.

4.

5.

6.

Nut

Receiver with 6 wire nuts

Transmitter incl. holder + 2 mounting screws

12V battery

Balancing kit

7.

8.

9.

10.

11.

3.

Installing Your Fan

Figures 1&2 are examples of different ways to

mount the outlet box.

If there isn't an existing cUL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 35 lbs). Do not use plastic outlet boxes.

Tools Required

Mounting Options

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

PERSONAL INJURY, MOUNT FAN ONLY TO AN OULET

BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND

USE THE MOUNTING SCREWS PROVIDED WITH THE

OULET BOX. OUTLET BOX COMMONLY USED FOR

THE SUPPORT OF LIGHTING FIXTURE MAY NOT BE

ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN

IF IN DOUBT.

Outlet Box

Figure 2

Figure 1

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 3

(available at your

Progress Lighting Retailer).

Figure 3

Phillips screwdriver, straight slot screwdriver, step

ladder and wire cutters.

4.

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Hanging the Fan

Attach the mounting bracket to the outlet box

with two screws and washers provided with the

outlet box. Make sure the bracket is tight and

secured (Fig. 4).

Remove the bottom guard by remove the four

screws from fan guard. (Fig. 5)

Lift fan into position by hanging the motor

assembly onto the hook from the ceiling

mounting bracket allowing it to hang freely

(Fig. 6).

Secure the safety cable to the building

structure with a wood screw. (wood screw not

supplied) (Fig. 6)

1.

2.

3.

4.

Making the Electrical

Connections

Outlet Box

Mounting Bracket

Screws

Bottom Guard

Motor

Safety

Cable

If you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

This remote control unit is equipped with 16 code

combinations to prevent possible interference

from or to other remote units. The frequency

switches on your receiver and remote control have

been preset at the factory. Please recheck to make

sure the switches on the remote control and the

receiver are set to the same position. Any

combination of settings will operate the fan as long

as the switches in the remote control and receiver

are set to the same position. (Figure 7)

NOTE

TO AVOID POSSIBLE ELECTRICAL SHOCK, BE

SURE ELECTRICITY IS TURNED OFF AT THE

MAIN FUSE BOX BEFORE WIRING.

NOTE

FAN MUST BE INSTALLED AT A MAXIMUM

DISTANCE OF 20 FEET FROM THE

TRANSMITTING UNIT FOR PROPER

SIGNAL TRANSMISSION BETWEEN THE

TRANSMITTING UNIT AND THE FAN'S

RECEIVING UNIT.

Figure 4

Figure 5

Figure 6

5.

CAUTION

DO NOT USE WITH A WALL LIGHT DIMMER

SWITCH.

1.

2.

3.

(Figure 8) Motor to receiver electrical

connections: Connect the black wire from the

fan to black wire marked "TO MOTOR L".

Connect the white wire from the fan to the

white wire marked "TO MOTOR N" from the

receiver. Connect the blue wire from the fan to

the blue wire marked "For Light" from the

receiver. Secure the wire connections with the

plastic wire connecting nuts provided.

(Figure 8) Receiver to house supply wires

electrical connections: Connect the black (hot)

wire from the ceiling to the black wire marked

"AC in L" from the receiver. Connect the white

(neutral) wire from the ceiling to the white wire

marked "AC in N" from the receiver. Secure

the wire connections with the plastic wire

connecting nuts provided.

(Figure 8) If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with a plastic nut

provided. After connecting the wires spread

them apart so that the green and white wires are

on one side of the outlet box and black and blue

wires are on the other side. Carefully tuck the

wire connections up into the outlet box.

Figure 7

Remote Control

Receiver

SUPPLY CIRCUIT

Figure 8

WHITE

BLACK

BLUE

Ground

Conductor

Outlet Box

Green

Ground

Lead

GREEN

Ground to

Downrod

BLACK BLACK

BLUE

WHITE

WARNING

CHECK TO SEE THAT ALL CONNECTIONS ARE

TIGHT, INCLUDING GROUND, AND THAT NO

BARE WIRE IS VISIBLE AT THE WIRE NUTS.

EXCEPT FOR THE GROUND WIRE.

6.

Attaching the Fan Blades

WARNING: TO REDUCE THE RISK OF

PERSONAL INJURY, DO NOT BEND THE BLADE

WHILE INSTALLING, BALANCING THE BLADES,

OR CLEANING THE FAN. DO NO INSERT

FOREIGN OBJECTS BETWEEN ROTATING FAN

BLADES.

Screws

Mounting

Bracket

Finishing the Fan

Installation

Figure 9

Decorative

Ring

Studs

Figure 10

Blade

Screws

Figure 11

1.

2.

Move fan into position over the mounting

bracket and secure with the 4 screws provided.

(Fig. 9)

Raise the decorative ring up against the

mounting bracket, the four supports inside the

decorative ring should be placed against the

four studs on mounting bracket, twist the

decorative ring clockwise until snug (Fig. 10).

1.

2.

Insert the blade through the slot in the blade

holder. Align the holes in the blade and the fan

blade holder and secure with a the screw and

fiber washer. (Fig. 11)

Tighten each screw securely starting with the

center screw. Make sure the blade is straight.

Repeat steps for the remaining blades.

7.

Installing the

Decorative Cover

CAUTION: Before starting installation,

disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box. Turning

power off using the fan switch is not sufficient to

prevent electric shock.

Remove the 1 of 3 screws from the posts of

the mounting ring and keep it for future use.

Loosen the other 2 screws. (Do not remove)

Place the key holes in the

decorative cover

over the two screws previously loosened from

the mounting ring. Turn the

decorative cover

until the decorative cover locks in place at the

narrow section of the key holes. (Fig. 13)

Securely tighten the two mounting screws

previously loosened and the one previously

removed.

Fit the decorative cap onto the decorative

cover and secure with the nut provided.

Re-Install the bottom guard back to the

fan

guard.

Screws

Bottom Guard

Decorativ Cap

Nut

Decorative Cover

Mounting Ring

Figure 13

1.

2.

3.

4.

5.

Installing the battery

Install 12V battery (included), to prevent damage

to transmitter, remove the battery if not used for

long periods. (Fig. 14)

Figure 14

Operating Your Transmitter

8.

Restore power to ceiling fan and test for proper

operation.

1. " , , " buttons:

These three buttons are used to set the fan

speed as follows:

= Low speed

= Medium speed

= High speed

2. The " " button turns the light ON or OFF and

also controls the brightness setting. Press and

release the button to turn the light ON or OFF.

Press and hold the button to set the desired

brightness. The light key has an auto-resume, it

will stay at the same brightness as the last time it

was turned off.

3. " " button: This button turns the fan off.

Figure 15

Figure 16

Figure 17

Speed settings for warm or cool weather depend

on factors such as the room size, ceiling height,

number of fans, etc.

The reverse switch is located on the top of motor

housing. Slide the switch to the left for warm

weather operation. Slide the switch to the right for

cool weather operation.

Warm weather - (Counter-Clockwise direction)

A downward air flow creates a cooling effect.(Fig.

16) This allows you to set your air conditioner on

a higher setting without affecting your comfort.

Cool weather - (Clockwise direction) An upward

airflow moves warm air off the ceiling area. (Fig.

17) This allows you to set your heating unit on a

lower setting without affecting your comfort.

NOTE

WAIT FOR FAN TO STOP BEFORE CHANGING

THE SETTING OF THE SLIDE SWITCH.

9.

Blade balancing

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct most fan

wobbling problems. Check after each step.

WARNING

Touching

ceiling

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE HOLDERS

WHILE INSTALLING, BALANCING THE

BLADES, OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS BETWEEN

ROTATING FAN BLADES.

Figure 19

Check that all blade and blade arm screws are

secure.

Most fan wobbling problems are caused when

blade levels are unequal. Check this level by

selecting a point on the ceiling above the tip

of one of the blades. Measure this distance as

shown in Fig. 19. Rotate the fan until the next

blade is positioned for measurement. Repeat

for each blade. The distance deviation should

be equal within 1/8".

Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

1.

2.

3.

4.

Figure 18

Attach the remote control holder with the remote

control holder mounting screw. (Figure 18)

Remote

Control

Holder

Screw

Installing the Remote Control

Holder

Care of Your Fan 10.

Here are some suggestions to help you maintain

your fan

IMPORTANT

MAKE SURE THE POWER IS OFF AT THE

ELECTRICAL PANEL BOX BEFORE YOU

ATTEMPT ANY REPAIRS. REFER TO THE

SECTION "MAKING ELECTRICAL

CONNECTIONS".

Because of the fan's natural movement, some

connections may become loose.

Check the

support connections, brackets, and blade

attachments twice a year.

Make sure they

are secure.

(It is not necessary to remove fan

from ceiling.)

Clean your fan periodically to help maintain

its new appearance over the years. Use only a

soft brush or lint-free cloth to avoid scratching

the finish. The plating is sealed with a lacquer

to minimize discoloration or tarnishing. Do

not use water when cleaning. This could

damage the motor, or the wood, or possibly

cause an electrical shock.

1.

2.

You can apply a light coat of furniture polish

to the wood blades for additional protection

and enhanced beauty. Cover small scratches

with a light application of shoe polish.

There is no need to oil your fan. The motor

has permanently lubricated bearings.

3.

4.

11. Troubleshooting

Solution

1. Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connections in the switch housing.

CAUTION: Make sure main power is off.

3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the lampshade are tight. Check that light bulb is also secure.

6. Some fan motors are sensitive to signals from solid-state variable speed controls. If you have installed this type of control,

choose and install another type of control.

7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.

1. Do not connect the fan with wall mounted variable speed control (s).

2. Make sure the dip switches are set correctly.

Problem

Fan will not start.

Fan sounds noisy.

Remote control

malfunction

Specifications 12.

2019 Progress Lighting, Inc.

701 Millennium Blvd.,

Greenville, SC 29607

c

These are approximate measures. They do not include Amps and Wattage used by the light kit.

13.04'

Fan Size Speed Volts Amps Watts RPM CFM N.W. G.W. C.F.

26"

Low

High

120

32.84

lbs

47.48

lbs

0.204

0.36

12.93

42.89

174

365

790.98

1766.21

Manuel d'installation du ventilateur de plafond

P250006

93114640_A

Garantie à vie limitée

Progress Lighting garantit à l’acheteur initial que les moteurs de ventilateur sont exempts de défauts électriques ou mécaniques

tant que l’acheteur initial est propriétaire du ventilateur. Les interrupteurs à chaînette, les interrupteurs inverseurs, les

condensateurs et les finis métalliques sont garantis contre les défauts de matériaux ou de fabrication pendant une période d’un

an à partir de la date d’achat. Le gauchissement des pales de bois ou de plastique n’est pas couvert par la présente garantie, ni la

corrosion ou la détérioration du fini des ventilateurs installés à moins de dix milles d’un bord de mer. Les garanties prolongées

pour les produits homologués ENERGY STAR® peuvent s’appliquer.

Lorsqu’ils sont installés correctement et dans des conditions d’utilisation normales, les ventilateurs de plafond Progress

Lighting dotés d’une source lumineuse à DEL intégrée sont garantis contre les défauts de matériaux et de fabrication causant le

non fonctionnement de la source lumineuse selon les spécifications pendant (i) cinq (5) ans à partir de la date d’achat des

modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences unifamiliales et (ii) trois (3) ans à

partir de la date d’achat des modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences

multifamiliales et pour les utilisations commerciales. Les ampoules à DEL fournies par Progress Lighting ne sont assorties

d’aucune autre garantie que celle du fabricant. Les ampoules autres qu’à DEL ne sont assorties d’aucune garantie.

En fournissant la preuve d’achat, l’acheteur initial peut retourner le ventilateur défectueux à son lieu d’achat pendant les 30

premiers jours afin qu’il soit remplacé. Après 30 jours, l’acheteur initial DOIT communiquer avec Progress Lighting au 864

678-1000 pour la réparation ou le remplacement du ventilateur, ce qui sera déterminé exclusivement par Progress Lighting et

constituera le seul et unique recours de l’acheteur.

Main-d’oeuvre et expédition exclus. La présente garantie ne couvre par les coûts et les frais associés à la main-d’oeuvre (y

compris, sans s’y limiter, les frais d’électricien) nécessaires à l’installation, au retrait ou au remplacement du ventilateur ou des

pièces du ventilateur.

La présente garantie ne s’applique pas en cas de perte ou de dommage découlant (i) de l’usure normale, de l’altération ou d’un

usage incorrect, abusif ou négligent ou (ii) d’une installation, d’une utilisation, d’une réparation ou d’un entretien inadéquats par

l’acheteur initial ou un tiers, y compris, sans s’y limiter, une tension électrique inadéquate ou une surtension, l’utilisation de

pièces ou d’accessoires inadéquats, une réparation non autorisée (effectuée ou tentée) ou l’omission d’entretenir le ventilateur.

LES GARANTIES QUI PRÉCÈDENT ÉNONCENT L’ENTIÈRE RESPONSABILITÉ DE PROGRESS LIGHTING AU

CHAPITRE DE LA GARANTIE AINSI QUE LE SEUL ET UNIQUE RECOURS DE L’ACHETEUR LIÉ À CES PRODUITS.

PROGRESS LIGHTING N’EST PAS RESPONSABLE DES DOMMAGES (Y COMPRIS LES DOMMAGES INDIRECTS,

SPÉCIAUX, ACCESSOIRES OU CONSÉCUTIFS) ATTRIBUABLES À LA DÉFECTUOSITÉ DU PRODUIT, QU’ILS

SOIENT LIÉS À UNE VIOLATION DE LA GARANTIE, UNE VIOLATION DU CONTRAT OU AUTRE. LA PRÉSENTE

GARANTIE REMPLACE TOUTE AUTRE GARANTIE, EXPRESSE OU IMPLICITE, Y COMPRIS TOUTE GARANTIE

DE QUALITÉ MARCHANDE, D’UTILITÉ À UNE FIN PARTICULIÈRE OU D’ABSENCE DE CONTREFAÇON.

Certains États ne permettent pas de limitation à la durée implicite d’une garantie ou d’exclusion ou de limitation des dommages

accessoires ou consécutifs. Par conséquent, les limitations ci-dessus pourraient ne pas s’appliquer

Date de l’achat

Magasin

Nº de modèle

Nº de série

Nº du fournisseur

CUP

109226

785247242412

785247240845

Table des matières

Règles de sécurité

.......................................................................................................................................................................

Déballer votre ventilateur

..........................................................................................................................................................

Installation du ventilateur

..........................................................................................................................................................

Fixation des pales du ventilateur..................................................................................................................................

Installation de la couverture décorative

...................................................................................................................................

Le fonctionnement de votre transmetteur

...............................................................................................................................

Entretien du ventilateur

.............................................................................................................................................................

Recherche des pannes

................................................................................................................................................................

Spécifications

..............................................................................................................................................................................

1.

2.

3.

6.

7.

8.

10.

11.

12.

Pour rèduire les risques de décharge électrique, s'assurer que l'électricité

est coupée au disjoncteur ou au boîtier de fusibles avant de commencer.

Tous les càblages doivent se conformer au Code National de électricite ét

aux normes électriques locales. L'installation électrique doit être

effectuée par un électricien licencié qualifie.

Le boîtier de prise et son support doivent être attachés correctement et

capables de supporter fiablement un poids minimum de 15.8 kg (35

livres). Utiliser seulement les boîtiers de prise homologués par l'cUL et

portant l'étiquette "POUR LE SUPPORT DE VENTILATEUR".

Le ventilateur doit être monté à une hauteur minimum de 2.1m (7

pieds) entre le bord de fuite des ailettes et le sol.

Éviter de placer des objets en travers des ailettes.

Pour éviter les blessures ou les dommages du ventilateur et autres

articles, faire attention en travaillant sur le ventilateur ou en le nettoyant.

Ne pas utilliser d'eau ou de détergent pout nettoyer le ventilateur ou ses

ailettes. Un chiffon de poussiére sec ou un chiffon lègérement humide

suffit pour la plupart des nettoyages.

Aprés le branchement électrique, las épissures de conducteurs doivent

être orientées vers le haut et poussées soigneusement dans le boîtier de

prise. Les fils doivent être éloignés les uns des autres, et le conducteur

mis à la terre et le conducteur de mise à la terre de l'appareil doivent être

placés sur un coté du boîtier de prise.

Toutes les vis de réglage doivent être vérifiées et resserrées si nécessaire

avant l'installation.

Adapté pour une utilisation avec la commande de vitesse à l'état solide.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

1. Règles de sécurité

REMARQUE

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES DE BLESSURE, NE PLIEZ PAS LES SUPPORTS

DE PALE (AUSSI APPELÉS BRIDES) PENDANT L'INSTALLATION DES

CROCHETS, L'ÉQUILIBRAGE DES PALES OU LE NETTOYAGE DU

VENTILATEUR.

AVERTISSEMENT

AFIN DE RÉDUIRE LE RISQUE D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE,

DE BLESSURE CORPORELLE, INSTALLER À UNE BOÎTE DE SORTIE

CAPABLE DE « SOUTENIR UN VENTILATEUR DE 15,8 KG (35 LB) OU

MOINS » ET UTILISER LES VIS D’INSTALLATION COMPRISES AVEC LA

BOÎTE DE SORTIE. LA PLUPART DES BOÎTES DE SORTIE UTILISÉES POUR

SOUTENIR LES LUMINAIRES SONT INADAPTÉES AU SOUTIEN D’UN

VENTILATEUR ET POURRAIENT EXIGER UN REMPLACEMENT. À CAUSE

DE L’INSTALLATION COMPLEXE DE CE VENTILATEUR, NOUS

RECOMMANDONS LES SERVICES D’UN MAÎTRE ÉLECTRICIEN.

Déballez votre ventilateur et vérifiez le contenu de l'emballage. Vous devriez trouver les éléments suivants:

Déballer votre ventilateur 2.

3

4

1

29

5

6

8

7

12

ab

11

10

Ensemble de lames

(4)

Support de montage

Fan motor assembly

Anneau décoratif

Couverture décorative

Casquette décorative

1.

2.

3.

4.

5.

6.

Écrou

Récepteur avec 6 écrous de plastique

Transmetteur + support + 2 vis de montage

Pile de 12V

Kit de balancement

7.

8.

9.

10.

11.

12. Desserrez les parties contenus dans un

sac :

a. Matériel de fixation de pales

(13 vis, 13 rondelles en fibre)

b. Matériel de montage

Connecteurs de fil en plastique

(3Pcs.)

La page est en cours de chargement...

Progress Lighting P250006 Guide d'installation

Progress Lighting P250006 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents