Dell W-Series 314/315 Access Points Le manuel du propriétaire

Taper
Le manuel du propriétaire
Dell Networking 310 Series Access Points
Regulatory Compliance and Safety Information Guide
0511905-01 | May 2016 1
Introduction
This document contains domestic and international regulatory compliance and safety information for Dell Networking 310 Series access points (W-AP314, W-
AP315, W-IAP314, and W-IAP315). To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.
Electrical and Environmental Specifications
Regulatory Information
Proper Disposal of Dell Equipment
Electrical and Environmental Specifications
For additional specifications on this product, please refer to the product data sheet at dell.com.
Electrical
Ethernet:
100/1000 Base-T auto-sensing Ethernet RJ45 interface
IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T)
Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (maximum).
Power:
48VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-48V36B)
Maximum power consumption (excluding USB): 20W (PoE) or 18.5W (DC)
Environmental
Operating:
Temperature: 0°C to +50°C (+32°F to +122°F)
Humidity: 5% to 93% non-condensing
Storage and transport:
Temperature: -40°C to +70°C (40°F to +158°F)
Regulatory Information
The following regulatory model names apply to the 310 Series access points:
W-AP314/W-IAP314: APIN0314
W-AP315/W-IAP315: APIN0315
CAUTION: All Dell access points should be professionally installed by a certified technician. The installer is responsible for ensuring that
grounding is available and meets applicable national and electrical codes.
ATTENTION: Tous les points d'accès Dell doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que
l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.
NOTE: If a power adapter other than the Dell-approved adapter is used in the US or Canada, it should be NRTL listed, without an output rated
48VDC, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in the US and Canada.
NOTE: For country specific restrictions and additional regulatory and safety guidelines, refer to the
Dell Networking W-Series Safety,
Environmental and Regulatory Information
document included with Dell controllers and Instant access points.
2 Dell Networking 310 Series Access Points | Regulatory Compliance and Safety Information Guide
FCC
This device is electronically labeled.
To view the FCC ID for controller-managed access points:
1. Log into the controller WebUI
2. Navigate to Maintenance > Controller > About
To view the FCC ID for Instant access points:
1. Log into the virtual controller WebUI
2. Navigate to Maintenance > About
FCC Class B Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Operation is subject to the following conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause
interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could cause interference
and/or damage to Licensed Exempt WLAN devices.
CAUTION: Access points are classified as radio transmission devices, and are subject to government regulations of the deploying country. The Network
Administrator(s) are responsible for ensuring that the configuration and operation of this equipment is in compliance with their country’s regulations.
Specifically, access points must use channel assignments appropriate to the locale in which the access points will be used. For a complete list of
approved channels in your country, refer to the Downloadable Regulatory Table (DRT) release notes at download.dell-pcw.com.
ATTENTION: Les points d'accès sont considérés comme appareils de transmission radio et sont soumis aux réglementations gouvernementales du pays
dans lequel ils sont déployés. Le ou les administrateurs réseau doivent s'assurer que la configuration et le fonctionnement de cet équipement sont
conformes aux normes de leurs pays. De façon plus précise, les points d'accès doivent employer des canaux adaptés à leur emplacement physique.
Pour obtenir une liste complète des canaux approuvés dans votre pays, reportez-vous aux notes de version DRT à l'adresse download.dell-pcw.com.
CAUTION: RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed
and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in 5.15 to 5.25 GHz
frequency range, this device is restricted to indoor use to reduce the potential for harmful interderence with co-channel Mobile Satellite
Systems.
ATTENTION: Déclaration sur les limites d'exposition aux radiofréquences : Cet équipement est conforme aux limites d'exposition aux
rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 20 cm par rapport à votre corps
pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-
récepteurs. En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en intérieur afin de
réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même canal.
CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
ATTENTION: Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est
susceptible d'annuler son droit d'utilisation.
Dell Networking 310 Series Access Points | Regulatory Compliance and Safety Information Guide 3
Canada
Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of
Industry Canada.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter
by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Déclaration d’Industrie Canada
Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.
Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain
maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à
ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace.
Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux conditions
suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles
de provoquer un dysfonctionnement.
EMC Class B Warning
이 기기는 가정용 (B ) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며 , 모든 지역에서 사용할 수 있습니다 .
EU Regulatory Conformance
Dell, hereby declares this device is in compliance with directives listed below:
EMC Directive 2004
Low Voltage Directive 2006
R&TTE Directive 1999
REACH Regulation (EC) No.: 1907/2006
RoHS Directive 2011
WEEE Directive 2002
A Declaration of Conformity for these directives is available for viewing at dell.com.
Medical
1. Equipment not suitable for use in the presence of flammable mixtures.
2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system
complies with the requirements of IEC 60601-1 3rd edition.
3. Wipe with a dry cloth, no additional maintenance required.
4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
5. No modifications are allowed without Dell approval.
第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。
前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
RF Warning
해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .
Proper Disposal of Dell Equipment
Dispose of Dell products per local regulation. For the most current information about Global Environmental Compliance and Dell products, visit dell.com.
WARNING: California Proposition 65: This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
4 Dell Networking 310 Series Access Points | Regulatory Compliance and Safety Information Guide
Copyright Information
© Copyright 2016 Hewlett Packard Enterprise Development LP. Dell™, the DELL™ logo, and PowerConnect™
are trademarks of Dell Inc.
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
This product includes code licensed under the GNU General Public License, the GNU Lesser General Public
License, and/or certain other open source licenses. You may request a copy of this source code free of charge
at HPE-Aruba-gplqu[email protected]. Please specify the product and version for which you are requesting source
code.
dell.com
Waste of Electrical and Electronic Equipment
Dell products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore
are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these
countries shall comply with the applicable national laws of countries implementing Directive 2002/96/EC on Waste of Electrical and
Electronic Equipment (WEEE).
India RoHS
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests,
Government of India.
European Union RoHS
Dell products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use
of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the
RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and
Bromine. Some Dell products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit
assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this directive.
China RoHS
Dell products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.
NOTE: Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device.
10
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)
䚼ӊৡ⿄
(Parts)
䪙
3E
∲
+J
䬝
&G
݁Ӌ䫀
&U

໮⒈㘨㣃
3%%
໮⒈Ѡ㣃䝮
3%'(
⬉䏃ᵓ
(PCA Boards)
ƻ ƻ ƻ ƻ
ᴎẄ㒘ӊ
(Mechanical Sub-Assemblies)
ƻ ƻ ƻ ƻ
ƻ˖
㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼
SJ/T11363-2006
ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dell W-Series 314/315 Access Points Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues