Dell W-Series 205H Access Points Le manuel du propriétaire

Taper
Le manuel du propriétaire
Dell Networking W-Series 205H Access Point
Regulatory Compliance and Safety Information Guide
0511811-01 | May 2015 1
Introduction
This document contains domestic and international regulatory compliance and safety information for the Dell W-Series 205H Series access
points. To ensure that this device complies with the regulatory standards for your country, please refer to the sections below.
Electrical and Environmental Specifications
Regulatory Information
Proper Disposal of Dell Equipment
Electrical and Environmental Specifications
For additional specifications for this product, please refer to the product data sheet at dell.com
Electrical
Ethernet:
4x 10/100/1000 Base-T auto-sensing Ethernet RJ-45 interface (E0-E3)
2x passive RJ-45 Pass-Through interface (E0/PT and PT)
IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)
PoE (IEEE 802.3af and 802.3at compliant), 48VDC (nominal) and 56VDC (maximum)/350mA
Power:
48VDC power interface, supports powering through an AC-DC power adapter
PoE support on Ethernet ports: 802.3af-compliant PoE sourcing device
Environmental
Operating:
Temperature: 0° C to +40° C (+32° F to +122° F)
Humidity: 5% to 95% non-condensing
Storage and transportation:
-Temperature: -40° C to +70° C (-40° F to +158°)
Regulatory Information
CAUTION: All Dell access points must be installed by a professional installer. The professional installer is responsible for ensuring that
grounding is available and it meets applicable local and national electrical codes.
ATTENTION: Tous les points d'accès Alcatel-Lucent doivent impérativement être installés par un professionnel agréé. Ce dernier
devra s'assurer de la disponibilité de la mise àla terre ainsi que de sa conformité aux normes électrique locales etnationales.
NOTE: If a power adapter other than the one provided by Dell is used in US or Canada, it should be NRTL Listed, with an output rated
48VDC, minimum 0.75A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in the US and Canada.
NOTE: For country-specific restrictions and additional regulatory information, refer to the
Dell Networking W-Series Safety Environmental
and Regulatory Information
document included with your Dell controller or Instant Access Point.
2 Dell Networking W-Series 205H Access Point | Regulatory Compliance and Safety Information Guide
Regulatory Model Name
The regulatory model name for this device is APINH205.
FCC
This device is electronically labeled.
To view the FCC ID for controller-managed access points:
1. Log into the controller WebUI
2. Navigate to Maintenance > Controller > About
To view the FCC ID for Instant Access points:
1. Log into the virtual controller WebUI
2. Navigate to Maintenance > About
FCC Class B Part 15
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s
instructions, may cause interference harmful to radio communications.
If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850 MHz and these Radars could
cause interference and/or damage to Licensed Exempt WLAN devices.
Canadian Statement
Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,”
ICES-003 of Industry Canada.
CAUTION: RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be
installed and operated with a minimum distance of 7.87 inches (20cm) between the radiator and your body for 2.4 GHz and 5 GHz
operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in
5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel
Mobile Satellite Systems.
ATTENTION: Déclaration sur les limites d'exposition aux radiofréquences :cet équipement est conforme aux limites d'exposition aux
rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 20 cm par rapport à votre
corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou
émetteurs-récepteurs. Lorsqu'il est utilisé en 5.15 à 5.25 GHz gamme de fréquences, ce dispositif est limité à une utilisation intérieure
pour réduire les risques d'interférence nuisible aux co-canal systèmes mobiles par satellite.
CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
ATTENTION: Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité
est susceptible d'annuler son droit d'utilisation.
Dell Networking W-Series 205H Access Point | Regulatory Compliance and Safety Information Guide 3
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved
for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Déclaration d’Industrie Canada
Cet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.
Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le
type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son
gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une
communication efficace.
Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux
conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris
les interférences susceptibles de provoquer un dysfonctionnement.
EU Regulatory Conformance
Dell, hereby declares that this device is compliant with the following European Directives:
R&TTE Directive 1999
WEEE Directive 2002
EMC Directive 2004
REACH Regulation (EC) No.: 1907/2006
Low Voltage Directive 2006
RoHS Directive 2011
The Declaration of Conformity for these directives is available for viewing at dell.com.
Medical
1. This equipment is not suitable for use in the presence of flammable mixtures.
2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting
medical system complies with the requirements of IEC 60601-1 3rd edition.
3. Wipe with a dry cloth, no additional maintenance required.
4. No serviceable parts, the unit must be sent back to the manufacturer for repair.
5. No modifications are allowed without Dell approval.
第十二條
  經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條
  低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有
干擾現象時,應立即停用,並改善至無干擾時方得繼續使用
  前項合法通信,指依電信法規定作業之無線電通信。
  低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電
機設備之干擾。
NOTE: Expected Service Life is 5 years.
NOTE: For additional compliance information, refer to the regulatory label on the side of the device.
4 Dell Networking W-Series 205H Access Point | Regulatory Compliance and Safety Information Guide
Copyright
© 2013 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks
®
, Aruba
Wireless Networks
®
, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System
®
.
Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.
All rights reserved. Specifications in this manual are subject to change without notice.
Originated in the USA. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code subject to
the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The
Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other
vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for this action and
indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against it with respect to
infringement of copyright on behalf of those vendors.
dell.com
Proper Disposal of Dell Equipment
Dispose of Dell products per local regulation. For the most current information about Global Environmental Compliance and Dell products, visit
dell.com.
Waste of Electrical and Electronic Equipment
Dell products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and
Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at
end of life of these products in these countries shall comply with the applicable national laws of countries implementing
Directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE).
India RoHS
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of
Environment & Forests, Government of India.
European Union RoHS
Dell products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS
restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically,
restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium,
Mercury, Hexavalent Chromium, and Bromine. Some Dell products are subject to the exemptions listed in RoHS
Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the
left indicating conformance to this directive.
China RoHS
Dell products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label (left).
10
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)
䚼ӊৡ⿄
(Parts)
䪙
3E
∲
+J
䬝
&G
݁Ӌ䫀
&U

໮⒈㘨㣃
3%%
໮⒈Ѡ㣃䝮
3%'(
⬉䏃ᵓ
(
PCA Boards)
ƻ ƻ ƻ ƻ
ᴎẄ㒘ӊ
(
Mechanical Sub-Assemblies)
ƻ ƻ ƻ ƻ
ƻ˖
㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼
SJ/T11363-2006
ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽ
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dell W-Series 205H Access Points Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues