Swing-N-Slide Playsets PB 8232 Mode d'emploi

Marque: Swing-N-Slide Playsets

Modèle: PB 8232

Taper: Mode d'emploi

Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545

Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232

ASSEMBLY INSTRUCTIONS

check out http://www.swing-n-slide.com/planupdates.htm

for updates to these instructions.

No. of Children: Up to 5

Min. Use Zone:

' x

Set Dim.

'W x

'L x 8'H

Est. Building Time: 1-1/2 hr.

29'

22'

PB 8232

SLIDE AND 4'' x 4'' LUMBER SOLD SEPARATELY

Reverso en español

Renverser en français

Installation Safety – Have You:

Consulted the assembly instructions supplied with your particular model?

Noted this accessory is to be used only on Swing•N•Slide approved designs? (Do not alter its design or add/remove components.)

Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.)

Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with

a metal file as needed, and coated fastener ends with lead free paint?

Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, garage,

house, overhanging branches, laundry lines, or electrical wires?

Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto

a hard surface can result in serious injury to the equipment user.)

Verified that suspended climbing ropes, chain,or cable are secured at both ends?

Consulted in assembly instructions of your particular model for minimum use zones?

Used a water sealant on your play set to protect the wood and prevent cracking and warping?

Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply?

Made sure not to allow children to use equipment until it is properly installed?

Made sure to adjust all swings so there is a minimum 8'' clearance between the swing and the ground surface?

Operating Safety – Have You:

Determined that on-site adult supervision is provided for children of all ages?

Warned children the following before allowing them to use the equipment?

Not to walk close to, in front of, behind or between moving items.

Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the

strength of chain or rope.

Not to swing empty seats or other accessories.

Not to slide down swing chains.

Be sure to sit in the center of the swing seat and other accessories with full weight on the seat.

Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not

limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard.

Not to climb or walk on the top of swing beams, railings or roof.

Not to use equipment in a manner other than intended.

Not to get off equipment while it is in motion.

Not to climb on the equipment when it is wet.

Be sure to go down slides feet first.

Determined that only one child per planned occupant seat should be allowed on this set at one time.

Determined children must be dressed appropriately for play. Avoid hooded jackets, bicycle helmets, clothing with draw strings and

loose fitting clothes which could become entangled or snagged on equipment.

Determined that suspended climbing ropes, chain, or cable cannot be looped back upon itself.

Made certain the slide is placed so that is is not in direct sunlight.

Safety Maintenance – At the beginning of every season and twice monthly thereafter:

Rake and check depth of loose fill protective surfacing material to prevent compaction and maintain appropriate depth. Replace as

necessary.

Check all nuts, bolts and C-Links during the usage season for tightness and tighten as required. (It is

particularly important that this procedure be followed at the beginning of each season.)

To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories when outdoors temp dips down to

or below 32° F and take indoors.

Oil all metallic moving parts monthly during usage period.

Check all hardware and equipment for sharp edges during usage season. (Replace when necessary. It is especially

important to do this at the beginning of each new season.)

Check swing seats, chains, ropes and cables monthly during usage season for evidence of deterioration. Severe rusting or excessive wear,

especially near the top swing hanger or at the seat connection are evidence of chain deterioration. Cracks in the protective plastic sleeve

or seat itself are also signs of deterioration. If any of these conditions exist, call 1-800-888-1232 to order replacement accessories.

Sand rusted metal parts and repaint using non-lead based paint.

Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.

Disposal Instructions

When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards

will exist at the time the set is discarded.

Important!

Additional Safety Instructions for all Swing-N-Slide Playground Equipment.

Save this instruction sheet in the event the manufacturer needs to be contacted.

Observing the following statements and warnings reduces the likelihood of serious or fatal injury

Safety Checklist for Swing-N-Slide Play Sets and Accessories

This product is intended for single family home/residential use only and not intended for use in any public setting.

Placement in any public setting constitutes a misuse of this product.

IMPORTANT!

ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS

According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions

permit stakes to be pulled out easily, cementing into ground is necessary.

• To anchor the unit to the ground, Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 18" (45mm x 95mm x 457mm) pressure-

treated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts). Attach with four (4) 16D (3-1/2")

galvanized nails per stake into each tower and/or A-frame upright.

• If the unit has a climbing rope, anchor the rope end.

• Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed. This may be accomplished by

using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission “Handbook for Public Playground Safety” lists the following materials and required

depths that are sufficient for home/residential application. For fall height protection up to 9 ft. (2.742m) [recommended for Swing•N•Slide kits]:

LOOSE FILL MATERIAL REQUIRED (UNCOMPRESSED) DEPTH

in. (mm)

Wood Mulch 9" (229mm)

Double Shredded Bark Mulch 9" (229mm)

Uniform Wood Chips 12" (305mm)

Fine Sand 12" (305mm)

Fine Gravel 12" (305mm)

These depths were derived from the CPSC Handbook. Swing•N•Slide has not done independent tests to determine these required depths.

When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This protective surfacing must extend a minimum of 6 ft.

(1.828m) in all directions from the perimeter of the equipment or from the outermost edges of any component. For example, a slide extending beyond the platform must have

protective surfacing at least 6 ft. (1.828mm) out from both sides as well as the end. For swings, the protective surface must extend at least 14 ft. (6m)

out from both the back and

front of the swing when the swing is in its rest position.

Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY

Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty provides confidence and demonstrates our commitment

to providing quality residential playground products.

MANUFACTURER’S LIFETIME LIMITED WARRANTY

Swing-N-Slide® warrants its thermoformed slides and climbing mountains to be free from defects in workmanship and materials, under normal use and conditions, for the

lifetime of the product.

MANUFACTURER’S 5 YEAR LIMITED WARRANTY

Swing-N-Slide® warrants its Custom Ready-to-Build Play Set kits and accessories to be free from defects in workmanship and materials, under normal use and conditions,

for a period of 5 years.

MANUFACTURER’S 5 YEAR LIMITED WARRANTY

Swing-N-Slide® warrants its No-Cut and Wood Complete Ready-to-Assemble Play Set kits against wood rot and termite damage, and to be free from defects in

workmanship and materials, under normal use and conditions, for a period of 5 years for structural wood components.

Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or

any other physical properties of wood that do not present a safety hazard, are not covered by this warranty.

MANUFACTURER’S ONE YEAR WARRANTY

Swing-N-Slide® warrants its canopy roofs and/or tarps, and Timber GLOVE lumber wrap to be free from defects in workmanship and materials, under normal use and

conditions, for a period of one year.

Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject

to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545. Any part(s) returned to Swing-N-

Slide® must have prior approved Return Authorization Number and proof of purchase, including the date of purchase. This warranty is valid only if the product is used for

the purpose for which it was designed and installed at a residential, single family dwelling. This warranty is void if the product is put to commercial or institutional use. This

warranty does not cover (a) products which have been damaged by acts of Nature, negligence, misuse, or accident, or which have been modified or repaired by

unauthorized persons; (b) the cost of labor; or the cost of shipping the product, any part, or any replacement product or part.

Swing-N-Slide® DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE

IMPLIED WARANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. Swing-N-Slide® WILL NOT BE LIABLE FOR ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the product subsequent to the original purchaser. Some states do not

allow limitations on implied warranties or exclusion of incidental or consequential damages, so these restrictions may not be applicable to you. This warranty gives you

specific legal rights. You may also have other rights, which vary from state to state.

This warranty also does not apply to:

• Structures not erected, maintained or inspected in conformance with Swing-N-Slide® installation plans

• Structures that have had parts added or substituted not in conformance with Swing-N-Slide® installation plans

• Parts that have been modified, altered or misused

• Parts that have not been used as designed or intended

• Damage due to acts of Nature, vandalism, abnormal use or abuse as determined by Swing-N-Slide®

For further information on playground safety,

the Consumer Product Safety Commission

(CPSC) publishes the Outdoor Home Playground Safety Handbook which can be downloaded for free

from www.cpsc.gov. An additional resource is the American Society of Testing and Materials (ASTM)

Standard Consumer Safety Performance Specification for Home Playground Equipment (ASTM F1148)

which can be purchased and downloaded from www.astm.org.

TOOLS REQUIRED • HERRAMIENTAS REQUERIDAS • OUTILS REQUIS

ELECTRIC DRILL

1/2" SOCKET & WRENCH

HAMMER

TAPE MEASURE

SAFETY GLASSES

& DUST MASK

(1) 3/8" DRILL BIT

PHILLIPS BIT

CARPENTER'S SQUARE

TOOLS REQUIRED

(1) T30 Torx® Bit

(1) T20 Torx® Bit

(178) 2-1/2'' Wood Screw

(18) 1-1/4'' Wood Screw

(16) 2'' Lag Screw

(3) 1''Truss Head Screw

(6) 5/16'' x 3-1/2'' Hex Head Bolt

(10) T-Nut

(4) Slotted Beam Clamp

(2) 1/2'' Panhead Screw

(2) 1/4'' Flat Washer

(2) 1-3/4'' Panhead Screw

(4) 1-1/2'' Lag Bolt

(10) 5/16'' Flat Washer

THIS PRODUCT IS

INTENDED FOR USE

BY CHILDREN FROM

AGES 2-10 YEARS

For Home / Residential

Use ONLY

1212 Barberry Drive

Janesville, WI 53545

1-800-888-1232

www.swing-n-slide.com

(1) Name Plate

PineBluff

Plan

(1) Plan

(4) Anchor-It Straps

(4) Anchor-It

(2) EZ Frame Brace (R)

(2) EZ Frame Brace (L)

(2) Swing Seat

weight limit: 115 lbs.

(4) Swing Hangers

(1) Safety Handle

(6) EZ Frame Brackets

PineBluff Board List

PineBluff Assembly Instructions

(6) 4'' x 4'' x 96''

96''

(8) 5/4'' x 6'' x 28''

28''

(1) 2'' x 4'' x 17-1/4''

17-1/4''

(2) 2'' x 4'' x 23-1/2''

23-1/2''

(2) 2'' x 4'' x 25''

25''

(1) 2'' x 4'' x 35''

35''

(3) 2'' x 4'' x 47-1/2''

47-1/2''

(6) 5/4'' x 6'' x 35''

35''

PURCHASED SEPARATELY

(1) 4'' x 4'' x120''

120''

English(*) Metric(Cm) English(*) Metric(Cm)

1x4 2.5x7.6 3/4x3-1/2 1.9x9

1x6 2.5x15.3 3/4x5-1/2 1.9x14

5/4x4 3.2x10.2 1x3-1/2 2.5x9

5/4x6 3.2x15.3

1x5-1/2

2.5x14

2x2 5x5 1-1/2x1-1/2 3.8x3.8

2x3 5x7.6 1-1/2x2-1/2 3.8x6.4

2x4 5x10 1-1/2x3-1/2 3.8x9

2x6 5x15.3 1-1/2x5-1/2

3.8x14

3x3 7.6x7.6 3 x3

4x4 10x10 3-1/2x3-1/2 9x9

(*) Estimated Sizing Due to Cutting Process

NO M INAL M ATERIAL SIZE

LISTED SIZE

TRUE SIZE

7.6x7.6

How to select the correct fastener

Use these 2 pictorial guides to help select the correct fastener(s) for the

lumber attachment you are making. Each diagram will highlight the correct

number of fasteners to use, and where to attach them.

PineBluff Assembly Instructions

(2) 2-1/2'' screws

Use 2" screws when mounting 5/4"

boards to 2"x4" boards.

5/4'' x 6'' to 2'' x 4''

(3) 2-1/2'' screws

Apply 2 1/2" screws to the 2"x4" boards

when attaching to 4"x4" uprights.

2'' x 4'' or 5/4'' x 6'' to 4'' x 4''

NOTE: All hardware to be driven until flush with surface of

wood or no deeper that 1/16''.

Fig. 1

PineBluff Assembly Instructions

4'' x 4'' x 96''

77-1/4''

50-1/2''

94-1/2''

2'' x 4'' x 47-1/2''

2'' x 4'' x 23-1/2''

(3)

2-1/2''

screws

per joint

Frame Assembly:

1. Install 2'' x 4'' boards as shown in (Fig. 1).

NOTE:

Double check your

measurements to make

sure the structure is

square.

2-1/2'' Wood Screw

(4)

2-1/2''

screws

per joint

(1)

EZ Frame Bracket

Per Side

Fig. 2

PineBluff Assembly Instructions

2'' x 4'' x 35''

5/4'' x 6'' x 35''

2'' x 4'' x 25''

8-1/2''

5-3/4''

8-1/2''

5/4'' x 6'' x 35''

DETAIL VIEW

UNIT ROTATED 180˚

(3)

2-1/2'' wood screws

per joint

Fig. 2a

Double check to make

sure structure is square

(2)

2-1/2''

screws

per joint

(2)

2-1/2''

screws

per joint

Install Frame Braces:

1. Install (1) 5/4'' x 6'', and (3) 2'' x 4'' boards as shown in (Fig. 2),

and (Fig. 2a).

2-1/2'' Wood Screw

Fig. 3

PineBluff Assembly Instructions

Platform Assembly:

1. Lift second half of Platform and secure in place in (4) locations as

shown in (Fig. 3).

(3)

2-1/2'' wood screws

per joint

2-1/2'' Wood Screw

(2)

2-1/2'' wood screws

per joint

Fig. 4

PineBluff Assembly Instructions

(8) 5/4'' x 6'' x 28''

NOTE: There must be a 1/2''

Nominal Gap between all

deck boards.

2-1/2'' Wood Screw

Install Deck:

1. Install Deck boards, evenly spaced with a 1/2'' Gap, as shown in

(Fig. 4).

(2)

2-1/2'' wood screws

per joint

Fig. 5

PineBluff Assembly Instructions

(5) 5/4'' x 6'' x 35''

17''

2-1/2'' Wood Screw

(3)

2-1/2'' wood screws

per joint

Install Climbing Wall Rungs:

1. Install 5/4'' x 6'' Climbing Wall Rungs as shown in (Fig. 5).

25-1/2''

34''

42-1/2''

51''

PineBluff Assembly Instructions

Fig. 6

3-1/2''

7-1/2''

1/2

120''

2''

21-3/8''

7/8

37-3/8''

51-1/4''

7/8

112-5/8''

1/2

86-5/8''

81-1/8''

1/2

67-1/4''

7/8

118-1/8''

Hole Locations

Platform

Swing Seat

A-Frame

Swing Beam Hole Locations

1. Install Swing Hangers into swing beam at

locations shown in (Fig. 6).

PineBluff Assembly Instructions

Fig. 7

Swing Beam Drill Locations

1. Step 1: Tap T-nut into 3/8’’ hole as shown in (Fig. 7).

2. Step 2: Place a bottom beam clamp over the swing hanger as shown in (Fig. 7).

3. Step 3: Insert the swing hanger into the beam and thread it into the T-nut until it is flush or near flush with the

top of the T-nut. A screwdriver may be used to twist the hanger (Fig. 7). Orient swing hanger as shown

in (Fig 7).

4. Step 4: Use (4) 1-1/4'' screws to secure beam clamp.

5. Check hanger to ensure it does not spin.

6. Repeat for all four hangers.

(4) 1-1/4'' screws

Swing Hanger

Use Screwdriver to aid in tightening

Bottom Beam Clamp

t-nut

Hammer

3/8'' hole

T-nut

1-1/4'' Screw

Align the edges of the 4" x 4" legs

with the edges of EZ Frame Bracket

Fig. 8

(8) 2-1/2’’ Screws

A-Frame Assembly

1. layout 4'' x 4’’s and 2'' x 4'' as

shown in (Fig. 8).

2. Align EZ Frame Bracket with face of

4'' x 4''s.

3. Secure EZ Frame Bracket with (8)

2-1/2'' screws to 4'' x 4''s making

sure they are flush with each other.

4. Secure 2'' x 4'' to 4'' x 4''s as

shown in (Fig. 8a).

5. Flip over and add 2nd bracket.

Repeat steps 2 and 3.

EZ Frame Bracket

4" x 4" x 96''

2" x 4" x 47-1/2"

4" x 4" x 96''

(3)

2-1/2'' screws

(3)

2-1/2'' screws

Fig. 8a

47"

PineBluff Assembly Instructions

2-1/2'' Wood Screw

94-1/2"

T-nut

2-1/2'' screws

Hex Bolt

Washer

Fig. 9

PineBluff Assembly Instructions

3-1/2'' Hex Bolt

A-Frame Assembly cont.

1. Attach A-Frame to Swing Beam using (2) hex bolts and 4 screws as shown in (Fig. 9).

2. Tighten hex bolt to flush with top of T-nut. Repeat on second bracket.

3. Repeat steps 1 & 2 to attach Swing Beam Assembly to the Deck, as shown in (Fig. 10).

Fig. 10

2-1/2'' Wood Screw

PineBluff Assembly Instructions

Fig. 11

Install EZ-Frame Braces:

1. Install (2) EZ-Frame Braces per side of the units as shown in

(Fig. 11).

2'' Lag Screw

2-1/2'' Wood Screw

(4)

2'' Lag Screws

AND

(4)

2-1/2'' wood screws

per Brace

(2) Braces per side of

unit

Anchor-It Installation.

nnssttrruuccttiioonnss ffoorr AAnncchhoorriinngg SSwwiinngg••NN••SSlliiddee AAccttiivviittyy CCeenntteerrss

1. De

termine the final location of your activity center.

2. Place the Anchor-It stakes adjacent to the base and near the corners of

your activity center (at the bottom of the legs on swing sets) and twist the

auger-style stakes into the ground until only the loop is exposed.

3. Place the metal strap through the loop of the Anchor-It stake and secure

it to the unit with a lag screw and washer as illustrated to the right.

Note: Attach the strap to the unit with as little play as possible using

whatever holes in the strap that work best.

Anchor-It

Fig. 12

1'' Truss Screw

Use truss head screws to

to secure slide to deck.

Slide Installation.

1. Install Slide centered in the provided

opening as shown in (Fig. 12).

2. Attach Stake to end of slide as shown in

(12a).

Fig. 13

1-1/2"

Lag Bolt

Metal

Strap

Anchor-It

PineBluff Assembly Instructions

2'' Above Ground

(2)

1-1/4'' screws

per joint

2'' x 4'' x 17-1/4''

Fig. 12a

5/16'' Flat

Washer

NEVER hang a swing seat by a

partial link of chain! Remove and

discard partial links.

Swing Seat Assembly.

1. Hold the swing seat vertically and insert uncoated chains through

the channels on the bottom of the swing seat. Note: A coat

hanger may be used to help pull chain through the swing seat.

One full link should show at each end of the seat (Fig. 14).

2. Place one covered chain onto each harness so that it fits at the top

of the V-hanger. Insert uncoated chains to bottom vinyl hooks of

V-hanger.(Fig. 16). Crimp harness end closed.

CAUTION: It is important that you crimp harness

ends completely closed before using (see Fig. 16).

Place end of harness with hooks on a hard surface and force

hooks closed with a hammer or squeeze closed with a pliers

until parts are touching. WARNING: Open hooks can

cause deep cuts.

3. Hang the chains from the nylon bushing swing hangers. Crimp the

hook opening closed with a pliers to secure the chains to the

swing hangers (Fig. 17). Make sure all connections are tightly

crimped and secure before using swing seat.

Fig. 14

Fig. 15

Fig. 16

Fig. 17

PineBluff Assembly Instructions

THIS PRODUCT IS

INTENDED FOR USE

BY CHILDREN FROM

AGES 2-10 YEARS

For Home / Residential

Use ONLY

1212 Barberry Drive

Janesville, WI 53545

1-800-888-1232

www.swing-n-slide.com

PROCESS

BLACK

PANTONE "NEWCO RED"

1/2'' Pan Head Screw

Fig. 18

ID TAG:

1. Secure your product ID tag onto easy to read

location of any 4'' x 4'' using (2) 1/2'' Pan Head

screws as shown in (Fig. 18).

ID TAG

Deck Surface

1/4''

washer

1- 3/4

Panhead

screw

Fig. 18a

Safety Handle:

1. Mount safety handle in the climber openings

approximately 11'' above the deck surface

(Fig. 18a).

Safety Handle

1-3/4 Panhead screw

11"

PineBluff Assembly Instructions

La page charge ...

Swing-N-Slide Playsets PB 8232 Mode d'emploi

Marque: Swing-N-Slide Playsets

Modèle: PB 8232

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Swing-N-Slide Playsets PB 8232 Operating instructions
español: Swing-N-Slide Playsets PB 8232 Instrucciones de operación

Swing-N-Slide Playsets PB 8232 Mode d'emploi

Swing-N-Slide Playsets PB 8232 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents