Manitowoc Ice ArcticPure Plus Water FiltersArcticPure Plus Water Filters Guide d'installation

Part Number: 000016341 Rev00 1/21

ArcticPure® Plus

Water Filter System

Installation, Operation and Maintenance Manual

Original Document

,

Caution

Read this instruction before operating this equipment.

Engineered for Ease

Table of Contents

Part Number: 000016341 Rev00 1/21 3

Section 1

General Information

Model Numbers ................................................................................................................ 5

Specifications .................................................................................................................... 5

Warranty Information........................................................................................................ 5

Warranty Registration & Claim Procedures ..................................................................... 5

Authorized Warranty Service ............................................................................................. 5

Exclusions ........................................................................................................................ 6

Safety Notices ................................................................................................................... 6

Definitions ....................................................................................................................... 6

Section 2

Installation

General ............................................................................................................................. 7

Safety ................................................................................................................................ 7

Location ............................................................................................................................ 8

Water Service .................................................................................................................... 8

Assembly - AR-10000-P/AR-20000-P/AR-40000-P ...........................................................8

Installation - AR-Pre-P ....................................................................................................... 9

Installation - AR-10000-P/AR-20000-P/AR-40000-P .......................................................... 10

Installation Checklist ....................................................................................................... 10

Start-Up Procedure .......................................................................................................... 10

Changing Cartridges ........................................................................................................ 11

Section 3

Troubleshooting

Troubleshooting Chart ..................................................................................................... 13

Repairing Inlet/Outlet Connections ................................................................................. 13

Replacement Filter Part Numbers .................................................................................... 13

Table of Contents

4 Part Number: 000016341 Rev00 1/21

THIS PAGE INTENTIONALLY LEFT BLANK

Part Number: 000016341 Rev00 1/21 5

Model Numbers

This manual covers the following models:

Model # Range Claims

Replacement

Cartridge

AR-10000-P

15,000 gal

(56,800 liter)

capacity

For ice machines

0 - 600 lbs

(0 - 272 kg)

Chlorine taste

and odor

reduction, scale

inhibition, Cyst

& Particulate

Class I claims

Case of 12

K00493

AR-20000-P

20,000 gal

(75,700 liter)

capacity

For ice machines

601 - 1,000 lbs

(273 - 453 kg)

Chlorine taste

and odor

reduction, scale

inhibition, Cyst

& Particulate

Class I claims

Case of 12

K00494

AR-40000-P

40,000 gal

(151,400 liter)

capacity

For ice machines

1,001 - 2,500 lbs

(454 - 1134 kg)

Chlorine taste

and odor

reduction, scale

inhibition, Cyst

& Particulate

Class I claims

Case of 12

K00495

AR-Pre-P

For use in

conjunction

with AR-10000-P

AR-20000-P

AR-40000-P

Sediment

reduction,

Particulate Class

III claim

Case of 12

K00496

Specifications

Model # Specifications Flow Rate

AR-10000-P

Pressure: 35 - 125 psi (207 - 862 kPa)

Temperature: 35 - 100°F (1.6 - 38°C)

Connections: 3/8"

Parker Quick Connect

Micron Rating: 0.5

.75 gpm

(2.84 lpm)

AR-20000-P

Pressure: 35 - 125 psi (207 - 862 kPa)

Temperature: 35 - 100°F (1.6 - 38°C)

Connections: 3/8"

Parker Quick Connect

Micron Rating: 0.5

1.25 gpm

(4.73 lpm)

AR-40000-P

Pressure: 35 - 125 psi (207 - 862 kPa)

Temperature: 35 - 100°F (1.6 - 38°C)

Connections: 3/8"

Parker Quick Connect

Micron Rating: 0.5

2.0 gpm

(7.57 lpm)

AR-Pre-P

Pressure: 35 - 125 psi (207 - 862 kPa)

Temperature: 35 - 100°F (1.6 - 38°C)

Connections: 3/8"

Parker Quick Connect

Micron Rating: 5.0

1.5 gpm

(5.6 lpm)

Warranty Information

For warranty information visit: www.manitowocice.com/

Service/Warranty

• Warranty Coverage Information

• Warranty Registration

• Warranty Verification

Warranty coverage begins the day the ice machine is

installed.

WARRANTY REGISTRATION & CLAIM PROCEDURES

Scan the QR code with your smart device or enter the link in

a web browser to access:

• Warranty information

• Warranty labor claim form

WWW.MANITOWOCICE.COM/SERVICE/WARRANTY

Authorized Warranty Service

To comply with the provisions of this warranty, a

refrigeration service company, qualified and authorized

by your Manitowoc distributor, or a Contracted Service

Representative must perform the warranty repair. If the

dealer you purchased the ArcticPure® Plus system from is

not authorized to perform warranty service, contact your

Manitowoc distributor or Manitowoc Ice for the name of the

nearest authorized service representative.

Section 1

General Information

6 Part Number: 000016341 Rev00 1/21

General Information Section 1

EXCLUSIONS

The following items are not included in the ArcticPure® Plus

system(s) warranty coverage:

• Wear items such as filter cartridges or o-rings.

• Normal maintenance or adjustments as outlined in this

manual.

• Repairs due to unauthorized modifications to the filter

system or use of non-standard parts without prior written

approval from Manitowoc Ice.

• Damage caused by improper installation of the filter

system or the ice machine, electrical supply, water supply

or drainage, or damage caused by floods, storms or other

acts of God.

• Premium labor rates due to holidays, overtime, etc.;

travel time; flat rate service call charges; mileage and

miscellaneous tools and material charges not listed on

the payment schedule. Additional labor charges resulting

from the inaccessibility of equipment are also excluded.

• Parts or assemblies subjected to misuse, abuse, neglect

or accidents.

• Damage or problems caused by installation, and/or

maintenance procedures inconsistent with the technical

instructions provided in this manual.

Safety Notices

DEFINITIONS

DANGER

Indicates a hazardous situation that, if not avoided, will

result in death or serious injury. This applies to the most

extreme situations.

n

Warning

Indicates a hazardous situation that, if not avoided, could

result in death or serious injury.

,

Caution

Indicates a hazardous situation that, if not avoided, could

result in minor or moderate injury.

Notice

Indicates information considered important, but not

hazard-related (e.g. messages relating to property

damage).

NOTE: Indicates useful, extra information about the

procedure you are performing.

Part Number: 000016341 Rev00 1/21 7

Section 2

Installation

General

These instructions are provided to assist the qualified

installer. Check your local Yellow Pages for the name of the

nearest Manitowoc distributor, or call Manitowoc Ice for

information.

The ArcticPure® Plus water filtration systems are designed

to reduce coarse and fine particulate matter from the

incoming potable water supply. Chlorine will be reduced in

the water so as not to adversely affect the ice produced or

the equipment components. Scale inhibitor is automatically

fed into the water to inhibit the formation of scale on

water solenoids and evaporator plates. The IAPMO R&T

mark indicates that these products have met certification

requirements under the NSF/ANSI & CSA standards listed in

the Performance Data Sheet. The UPC mark indicates that

these products have met the applicable U.S. and Canadian

requirements for plumbing products.

• DO NOT install on line pressure above 125 psi (862 kPa).

• DO NOT install on hot water line. Maximum temperature

allowed is 100°F (38°C).

• DO NOT install in direct sunlight.

• DO NOT reverse connections. The system must be

installed with the inlet and outlet as labeled.

• DO NOT install ArcticPure® Plus filter systems in locations

where they can be damaged by other free-standing

equipment.

• PROTECT from freezing.

• INSTALLATION must comply with existing state or local

plumbing codes.

This piece of equipment has American sizes on hardware. All

metric conversions are approximate and vary in size.

Safety

Always follow these safety precautions when installing and

operating the water filter system.

n

Warning

DO NOT use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

Notice

DO NOT use a torch or other high temperature sources

near filter or cartridge.

https://www.iapmort.org/media/5271/rt_markguidelines.pdf

AR-Pre-P, AR-10000-P, AR-20000-P and AR-40000-P systems are certified by IAPMO R&T against CSA B483.1; NSF/ANSI 372 for

Low Lead Content; NSF/ANSI 42 and/or *NSF/ANSI 53 for the reduction of claims listed in the Performance Data Sheet.

*NSF/ANSI 53 Cyst reduction claims are valid only when system flow is restricted at or below the specified range and/or

as specified in the ice machine capacity ranges on page 5. System flow rates should be verified after installation to ensure

filterable cyst reduction per the above.

Please see ice machine manufacturer’s technical publications for internal flow controller maximum operating flow rate

specifications.

8 Part Number: 000016341 Rev00 1/21

Installation Section 2

Location

ArcticPure® Plus water filtration systems must be located

on the incoming cold water line and preferably away from

heavy traffic areas. The system must be mounted on a wall

or structure that will support the weight of the system when

filled with water.

Notice

This product is designed for cold water use only (less than

100°F [38°C]). Passing hot water through this product

may seriously damage filter housings and/or cartridges

and affect warranty coverage.

Important

Do not disassemble manifold head. No user serviceable

parts are available. The entire manifold head is the only

available replacement part.

ArcticPure® Plus systems may be used with metal or non-

metallic piping systems.

NOTE: Any non-metallic fittings used in the installation must

be of adequate rating for the line pressure.

Water Service

All ArcticPure® Plus systems come with 3/8" Parker

connections on the inlet and outlet ports.

Parker connections are suitable for use with the following

tubing:

• Polyethylene

• Nylon

• Polyurethane

• Seamless Brass (soft)

• Seamless Copper (soft)

• Seamless Mild Steel (soft)

Notice

DO NOT use with hard metal tubing such as:

• Stainless steel

• Chrome plated copper

• Hard metal polished tubing



NOTE: The head/bracket will be packed separately from the

filter cartridge in the product box.

1. Locate position to mount the filter system. Be sure

to leave enough clearance (a minimum of 2" [5 cm]

beneath the filter cartridge length is recommended) to

allow for cartridge change out.

2. Mark and drill mounting holes.

3. Mount filter head, using key hole slots in the mounting

bracket.

4. Remove the protective cap from the cartridge.

5. Inspect the cartridge and o-rings for damage. See

Recommended Replacement Parts List in Replacement

Filter Part Numbers if replacement is required.

,

Caution

Do not use petroleum jelly to lubricate o-rings.

6. Lubricate o-rings with food grade lubricant - Do not use

petroleum jelly.

7. With the product label facing to the left, insert the

cartridge into the filter head. Rotate 1/4 turn to the right

to secure. Product label will face forward.

Part Number: 000016341 Rev00 1/21 9

Section 2 Installation



NOTE: If the AR-Pre-P is being retrofitted to an existing

ArcticPure® Plus system, shut off the incoming water supply,

relieve the filter pressure by removing the existing filter

cartridge(s), and disengage the water inlet line. A small

quantity of water will be vented from the cartridge body.

1. Mark and drill the mounting holes for the AR-Pre-P.

2. Insert the precut tubing into the outlet fitting of the AR-

Pre-P head.

3. Insert opposite end of the tubing into the inlet fitting of

the primary filter assembly.

Notice

The fitting will grip before it seals. Tubing must be pushed

into the tube stop to prevent leaks.

4. Pull on the tubing to be sure it is secure. If the tubing

releases, refer to the Troubleshooting section of this

manual to reinstall.

5. Align the prefilter mounting keyhole slots with the

predrilled holes.

6. Install mounting screws and tighten.

7. Insert incoming water line into the inlet port of the

AR-Pre-P. Follow notes and steps 1-3 under “Installation -

AR-10000-P/AR-20000-P/AR-40000-P”.

8. Remove the protective cap from the cartridge.

9. Inspect the cartridge and o-rings for damage. See

Recommended Replacement Parts List if replacement is

required.

,

Caution

Do not use petroleum jelly to lubricate o-rings.

10. Lubricate o-rings with food grade lubricant - Do not use

petroleum jelly.

11. With the product label facing to the left, insert the

cartridge into the filter head. Rotate 1/4 turn to the right

to secure. Product label will face forward.

10 Part Number: 000016341 Rev00 1/21

Installation Section 2



Shut off the incoming water supply.



NOTE: Please review the following recommendations before

installing the water lines.

• Tubing must be 3/8" O.D., (.371 - .376).

• Cut the tube square. The outside diameter must be free

of score marks.

• Burrs and sharp edges must be removed prior to

installation.

NOTE: Use a tube insert for thin-walled plastic tubing.

To install water lines into the inlet/outlet ports:

1. Insert water line tubing into the inlet port fitting.

Notice

The fitting will grip before it seals. Tubing must be pushed

into the tube stop to prevent leaks.

2. Pull on the tubing to be sure it is secure. If the tubing

releases, refer to the Troubleshooting section of this

manual to reinstall.

3. Repeat for the outlet port fitting. Connect outlet water

line to the potable water connection on the ice machine.

NOTE: For water-cooled machines, be sure that the filter

system only feeds the potable water connection.





Have the min.-max. water temperature and pressure

been checked? (Refer to “Installation” on page 7)



Has the filter system been installed away from heavy

traffic areas?



Is the system installed securely to the mounting surface?



Has the water supply line been checked for suitability?

(Refer to “Water Service”)



Have the water supply lines been securely installed

into the inlet/outlet ports? (Refer to “Installation - AR-

10000-P/AR-20000-P & AR-40000-P”)



1. Turn on the incoming water supply.

2. Check for leaks. If the connections are leaking, refer to

the Troubleshooting section of this manual to reinstall.

NOTE: System should be flushed for 10 minutes to remove

trapped air and carbon fines.

NOTE: The filter pressure will decrease as the cartridge life

decreases.

AR-Pre-P, AR-10000-P, AR-20000-P and AR-40000-P systems are certified by IAPMO R&T against CSA B483.1; NSF/ANSI 372 for

Low Lead Content; NSF/ANSI 42 and/or *NSF/ANSI 53 for the reduction of claims listed in the Performance Data Sheet.

*NSF/ANSI 53 Cyst reduction claims are valid only when system flow is restricted at or below the specified range and/or

as specified in the ice machine capacity ranges on page 5. System flow rates should be verified after installation to ensure

filterable cyst reduction per the above.

Please see ice machine manufacturer’s technical publications for internal flow controller maximum operating flow rate

specifications.

Model Flow Rate

AR-10000-P At or below 0.75 gpm (2.84 lpm)

AR-20000-P At or below 1.25 gpm (5.68 lpm)

AR-40000-P At or below 2.0 gpm (7.57 lpm)

Part Number: 000016341 Rev00 1/21 11

Section 2 Installation



ArcticPure® Plus cartridges will need to be changed for one

or more of the following reasons:

• The filter has trapped water-borne sediment and the

water flow has stopped or water pressure through the

filter has dropped below 20 psi (138 kPa).

• The maximum life of the carbon filter has been reached

and the filter will no longer reduce chlorine to acceptable

levels.

• The scale inhibitor has been completely dissolved and

hard scale build-up may accelerate.

It is recommended that ArcticPure® Plus filter cartridges be

changed out:

• Every 6 months or when water pressure through the

system drops below 20 psi (138 kPa), whichever occurs

first.

To change the filter:

1. Rotate the cartridge 1/4 turn to the left and pull down.

The cartridge should easily release. Dispose of used

cartridge.

Important

ArcticPure® Plus systems are equipped with internal shut-

off valves. It is not necessary to shut off the incoming

water supply during cartridge change out.

2. Remove the protective cap from the cartridge.

3. Inspect the cartridge and o-rings for damage. See

Replacement Parts list if replacement is required.

Lubricate o-rings with food grade lubricant.

,

Caution

Do not use petroleum jelly to lubricate o-rings.

4. With the product label facing to the left, insert the

cartridge into the filter head and push up. Rotate 1/4 turn

to the right to secure. Product label will face forward.

,

Caution

Should the cartridge drop from a height of greater than 3

feet, inspect the outer casing. If there is any evidence of

the case cracking do not use.

12 Part Number: 000016341 Rev00 1/21

Installation Section 2

THIS PAGE INTENTIONALLY LEFT BLANK

Part Number: 000016341 Rev00 1/21 13

Important

Please use the Troubleshooting Chart to repair the system.

If system still does not work properly, contact Manitowoc

Service for assistance.

Troubleshooting Chart

Problem Cause To Correct

No water through filter system

Water to filter system shut off Turn on water supply

Filter cartridges plugged Replace filter cartridges — See “Changing Cartridges”

Low water flow through filter

System below 25 psi

Restore system pressure

Repair water supply to filter

Filter cartridges plugged Replace filter cartridges — See “Changing Cartridges”

Water leak on water inlet/outlet

Water line ends are damaged

Trim water line to remove damaged area — See

“Repairing Inlet/Outlet Connections”

O-ring in filter head is damaged Replace o-ring — See “Changing Cartridges”

Water leak between head and filter cartridge Damaged o-ring on filter cartridge Replace o-ring — See “Changing Cartridges”

Repairing Inlet/Outlet Connections

A leak may occur at the inlet/outlet connections because of

defective tubing. To repair:

1. Turn off incoming water supply and depressurize system

by removing the filter cartridge(s).

2. Disconnect the water line by pushing the collet squarely

against the face of the fitting.

3. Pull the tubing to release.

4. To repair the connection, cut off at least 3/8" (6.4 mm)

from the end of the tubing. Tubing ends must be cut

square to ensure a positive seal.

5. Refer to notes and instructions under “Installation -

AR-10000-P/AR-20000-P/AR-40000-P” to reconnect the

water line.

Replacement Filter Part Numbers

Part Number

Case

Description

K00496 AR-Pre-P Cartridge

K00493 AR-10000-P Cartridge

K00494 AR-20000-P Cartridge

K00495 AR-40000-P Cartridge

Section 3

Troubleshooting

14 Part Number: 000016341 Rev00 1/21

Troubleshooting Section 3

THIS PAGE INTENTIONALLY LEFT BLANK

MANITOWOC ICE

2110 SOUTH 26TH STREET, MANITOWOC, WI 54220

800-545-5720

WWW.MANITOWOCICE.COM

Part Number: 000016341 Rev00 1/21

Número de pieza: 000016341 Rev00 1/21

ArcticPure® Plus

Sistema de filtrado de agua

Manual de instalación, operación y mantenimiento

Documento original

,

Precaución

Lea estas instrucciones antes de comenzar a operar este equipo.

Diseñado para la facilidad

Tabla de Contenidos

Número de pieza: 000016341 Rev00 1/21 3

Sección 1

Información general

Números de modelo .......................................................................................................... 5

Especificaciones ................................................................................................................ 5

Información de garantía .................................................................................................... 5

Registro de la garantía y procedimientos de reclamación ..............................................5

Servicio de garantía autorizado ......................................................................................... 5

Exclusiones ...................................................................................................................... 6

Avisos de seguridad ........................................................................................................... 6

Definiciones .....................................................................................................................6

Sección 2

Instalación

Generalidades ................................................................................................................... 7

Seguridad .......................................................................................................................... 7

Ubicación .......................................................................................................................... 8

Servicio de agua ................................................................................................................ 8

Montaje: AR-10000-P/AR-20000-P/AR-40000-P..............................................................8

Instalación: AR-Pre-P ......................................................................................................... 9

Instalación: AR-10000-P/AR-20000-P/AR-40000-P ............................................................ 10

Lista de verificación de instalación ................................................................................... 10

Procedimiento de arranque ............................................................................................. 10

Cambio de cartuchos ....................................................................................................... 11

Sección 3

Solución de problemas

Cuadro de solución de problemas .................................................................................... 13

Reparación de conexiones de entrada o salida ................................................................. 13

Números de pieza de los filtros de repuesto .................................................................... 13

Tabla de Contenidos

4 Número de pieza: 000016341 Rev00 1/21

ESTA PÁGINA SE DEJÓ EN BLANCO INTENCIONALMENTE

La page est en cours de chargement...

Manitowoc Ice ArcticPure Plus Water FiltersArcticPure Plus Water Filters Guide d'installation

Manitowoc Ice ArcticPure Plus Water FiltersArcticPure Plus Water Filters Guide d'installation

dans d''autres langues

Documents connexes

Autres documents