Digital Monitoring Products 263LTE Cellular Communicator Guide d'installation

Marque
Digital Monitoring Products
Modèle
263LTE Cellular Communicator
Catégorie
Protection contre le feu
Taper
Guide d'installation

Ce manuel convient également à

DESCRIPTION
Figure 1: 263LTE
1INSTALL THE 263LTE
Caution: Touch grounded metal to discharge
static before handling the panel.
XT30/XT50 Series Panels
1. Open the panel enclosure, set the reset
jumper, and remove power from the panel.
2. Insert the included stando into the
panel stando hole.
3. Align the 263LTE SMA antenna connector
with the antenna hole in the top of the panel
enclosure, place one washer around the
connector, and secure it on the 12-pin cell
module connector. See Figure 2.
Note: For XT50 panels, install the included
washers between the antenna and the panel.
4. Align the 263LTE stando hole with the
stando already placed in the panel and
snap it into place.
The 263LTE Series Cellular
Communicator provides
a fully-supervised alarm
communication path over
an LTE network. The 263LTE
installs on the panel inside
the enclosure and is powered
by the panel so no additional
enclosure, power supply, or
battery back-up is needed.
Compatibility
Control panel firmware should
be updated to the following
versions when installing a
263LTE:
• XT30/XT50 Series
panels Version 213
(4/12/22) and higher
• XR150/XR550 Series
panels Version 213
(4/8/22) and higher
What is Included
• 263LTE Cellular
Communicator
• 383 antenna
• PCB stando
• Hardware pack
1
2
3
4
Figure 2: 263LTE on an XT30/XT50 Panel
Back of the
263LTE
Stando and
Stando Hole SMA Connector
Figure 3: 263LTE on an XR150/XR550 Panel
Stando and
Stando Hole
Back of the
263LTE
XR150/XR550 Series Panels
1. Open the panel enclosure, set the reset
jumper, and remove power from the panel.
2. Insert the included stando into the
XR150/XR550 Series panel stando hole.
3. Secure the 263LTE on the 12-pin cell module
connector. See Figure 3.
4. Align the 263LTE stando hole with the
stando already placed in the panel and
snap it into place.
Washer (XT50 only)
263LTE SERIES CELLULAR
COMMUNICATOR
Installation Guide
2 263LTE SERIES INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS
1. Navigate to the Dealer Admin site (dealer.securecomwireless.com).
2. Click Customers in the right-side menu and select a customer.
3. Click Add System.
4. Enter a System Name.
5. Select either Cellular or EASYconnect + Cell Backup in the Connection Type field.
6. Enter the SIM number found on the 263LTE label and click Get Status.
7. Enter the Account Number.
8. Select a Rate Plan for the 263LTE.
9. Click Activate Cellular Device.
2
Dealer Admin Activation
CONNECT THE ANTENNA
Be sure to only use the included 383 antenna when installing the 263LTE.
XT30/XT50 Series Panel
1. If installing an XT50, place the second washer around the 263LTE SMA connector and
connect it to the included antenna at the hole in the top of the panel.
2. Connect the 263LTE SMA connector to the included antenna at the hole in the top of
the panel. See Figure 4.
XR150/XR550 Series Panel
1. Attach one end of the included coax cable to the 263LTE SMA connector.
2. Position one washer onto the other end of the coax cable and push the threaded end
through the antenna knockout hole.
3. Position the second washer onto the threaded end that extends through the antenna
knockout hole and secure the nut.
4. Attach the included LTE antenna to the coax cable SMA connector. See Figure 5.
3ACTIVATE THE 263LTE
Before power is reapplied to the panel, cellular service must be activated. The 263LTE
comes ready for activation with SecureComTM Wireless, LLC. Use Dealer AdminTM (dealer.
securecomwireless.com), the Tech APPTM ,or Remote LinkTM, or call DMP Customer Service
(1-866-266-2826) to activate the 263LTE.
CONNECT THE ANTENNA
LTE Antenna
Figure 4: XT30/XT50 Series Panel
1
2
3
4
Figure 5: XR150/XR550 Series Panel
SMA
Connector
LTE Antenna
Coax Cable
SMA Connector
263LTE
SMA
Connector
Coax
Cable
Antenna
Knockout Hole
Brass Washers
263LTE SERIES INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3
TEST THE 263LTE
1. Navigate to the Tech APP.
2. Tap Find a Customer then search for a customer.
3. Tap Add a System.
4. Enter a System Name.
5. Scan or enter the Serial #.
6. Select either Cellular or EASYconnect + Cell Backup in the Connection Type field.
7. Enter the Account Number.
8. Enter the SIM Number found on the 263LTE label then tap Get SIM Status.
9. Select a Rate Plan for the 263LTE.
10. Tap Activate Cellular Device.
Tech APP Activation
The panel provides a diagnostic function to test the communication integrity and cellular
signal strength of the 263LTE to the nearest tower for the cellular carrier. To use the
diagnostic function, reset the panel, enter 2313 (DIAG), and press CMD.
Communication Status
This option tests the individual components of cellular or wireless network
communication.
1. Select CELL STATUS from the Diagnostic menu. Possible test results are shown
in Table 1.
2. Select YES to continue through the remaining component tests or select NO to
stop testing and return to CELL STATUS.
Confirmed Faulty
MODEM OPERATING NO MODEM FOUND
IDENTIFIED NO SIM CARD
TOWER DETECTED NO TOWER
REGISTERED NOT REGISTERED
CONNECT SUCCESS CONNECT ERROR
NOT ACTIVATED
CELL PATH GOOD NO ACK RECEIVED
Remote Link Activation
1. Navigate to Remote Link and select a panel.
2. Select Program in the top menu and select Communications from the drop-
down menu.
3. Select Cellular Network as the Communication Type and click Activate.
4. Select SIM as the SIM Type.
5. Enter the SIM number found on the 263LTE label and press the Tab key.
6. Select a Rate Plan for the 263LTE and click Activate.
4
Table 1: Cell Status Test Results
Designed, engineered, and
manufactured in Springfield, Missouri
using U.S. and global components.
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
888.436.7832 | DMP.com
© 2022 Digital Monitoring Products, Inc.
LT-1592 1.02 21362
Specifications
Primary Power 12 VDC from panel
Current Draw
Standby 20 mA
Alarm 20 mA (47 mA peak transmitting)
Ordering Information
263LTE-V Cellular Communicator for Verizon LTE
263LTE-A Cellular Communicator for AT&T LTE
Accessories
381-2 18” Coax Cable
381-12 12’ Coax Extension
381-25 25’ Coax Extension
383 Dual Band Antenna (included)
386 Antenna Mounting Bracket
263EXT Cellular Extension Module
Compatibility
XT30/XT50 Series Version 212 and higher
XR150/XR550 Series Version 212 and higher
Certifications
California State Fire Marshal (CSFM)
FCC Part 15: RI7ME910C1NV (Telit)
RI7ME910G1W1 (Telit)
XMR201707BG96 (Quectel)
XMR201907BG95M3 (Quectel)
Industry Canada: 5131A-ME910C1NV (Telit)
5131A-ME910G1W1 (Telit)
10224A-201709BG96 (Quectel)
10224A-2019BG95M3 (Quectel)
New York City (FDNY)
Underwriters Laboratory (UL) Listed
• ANSI/UL 294 Access Control System Units
• ANSI/UL 636 Holdup Alarm Units and System
Accessory
• ANSI/UL 1023 Household Burglar
• ANSI/UL 1076 Proprietary Burglar
• ANSI/UL 1610 Central Station Burglar
• ANSI/UL 1635 Digital Burglar
• ANSI/UL 985 Household Fire Warning
• ANSI/UL 864 Fire Protective Signaling 9th Edition.
• ANSI/UL 365 Police Sta. Connected Burg Alarm
Units & Systems
• ANSI/UL 609 Local Burg Alarm Units & Systems
Underwriters Laboratory of Canada (ULC) Listed
• ULC S304 Central Station Burglar
• ULC - Subject - C1023 Household Burglar
• ULC/ORD - C1076 Proprietary Burglar
• ULC - S545 Household Fire
• ULC - S559 Equipment for Fire Receiving
Centers and Systems
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons. It must not
be located or operated in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Information
This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6.
The system must be installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm) to maintain
compliance with the General Population limits.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de
sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne
présente en conformité avec les limites permises d’exposition du grand public.
263LTE SERIES CELLULAR
COMMUNICATOR
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Digital Monitoring Products 263LTE Cellular Communicator Guide d'installation

Marque
Digital Monitoring Products
Modèle
263LTE Cellular Communicator
Catégorie
Protection contre le feu
Taper
Guide d'installation
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents