Digital Monitoring Products LT 1873 Installation & Programming Guides

Taper
Installation & Programming Guides
263LTE-V5 CELLULAR
COMMUNICATOR
Installation Guide
DESCRIPTION
Figure 1: 263LTE-V5
The 263LTE-V5 Cellular
Communicator provides
a fully-supervised alarm
communication path over
the Verizon LTE network. The
263LTE-V5 installs on the panel
inside the enclosure and is
powered by the panel so no
additional enclosure, power
supply, or battery back-up is
needed.
With the 263LTE-V5, Verizon
LTE does not support
MyAccess™ text messaging.
Compatibility
Control panel firmware should be
updated to the following version
when installing a 263LTE-V5:
XR100/XR500 Series panels
with Version 213 or higher
What is Included?
263LTE-V5 Cellular
Communicator
383 Antenna
PCB stando
1INSTALL THE 263LTE-V5
XR100/XR500 Series Panel
1. Remove all power from the panel.
2. Disconnect the coax cable.
3. Remove the cell card from the 464
interface card.
4. Install the new cell card onto the 464
interface card.
5. Reconnect the coax cable.
6. Remove old antenna.
7. Install the new antenna.
8. Reconnect power.
2Cellular service is required before you can use the 263LTE-V5 for signal
transmission. The 263LTE-V5 comes ready for activation with SecureCom™
Wireless, LLC. Use the Dealer Admin™ site (DMPDealerAdmin.com), the Tech
APP™, Remote Link™, or call DMP Customer Service (1-866-266-2826) to activate
the 263LTE-V5.
ACTIVATE THE 263LTE-V5
Remote Link Activation
Dealer Admin Activation
1. Navigate to the Dealer Admin site (DMPDealerAdmin.com).
2. Click Customers in the right-side menu and select a customer.
3. Click Add System.
4. Enter a System Name.
5. Select either Cellular or EASYconnect + Cell Backup in the Connection
Type field.
6. Enter the SIM number found on the 263LTE-V5 label and click Get Status.
7. Enter the Account Number.
8. Select a Rate Plan for the 263LTE-V5.
9. Click Activate Cellular Device.
Model 381-2
Coax Cable
from 263
Nut
Washers
Antenna
Connector
18 19 20 21 22 23 24 25 26 27 28
Z5 Z6 Z7 Z8 Z9+ Z9- Z10+ Z10-
GND
GND
XR100/XR500
Panel
263
Cell Module
464-263
263
Figure 2: 464-263LTE-V5 Wiring
1. Navigate to the Tech APP.
2. Tap Find a Customer then search for a customer.
3. Tap Add a System.
4. Enter a System Name.
5. Scan or enter the Serial #.
6. Select either Cellular or EASYconnect + Cell Backup in the Connection
Type field.
7. Enter the Account Number.
8. Enter the SIM Number found on the 263LTE-V5 label then tap Get SIM
Status.
9. Select a Rate Plan for the 263LTE-V5.
10. Tap Activate Cellular Device.
Tech APP Activation
1. Navigate to Remote Link and select a panel.
2. Select Program in the top menu and select Communications from the
drop-down menu.
3. Select Cellular Network as the Comunication Type and click Activate.
4. Select SIM as the SIM Type.
5. Enter the SIM number found on the 263LTE-V5 label and click Activate.
6. Select a Rate Plan for the 263LTE-V5 and click Activate.
Designed, engineered, and
manufactured in Springfield, MO
using U.S. and global components.
LT-1873 18484
263LTE-V5 CELLULAR
COMMUNICATOR
Specifications
Primary Power 12 VDC from panel
Current Draw
Standby 14 mA
Alarm 14 mA (46 mA peak transmitting)
Accessories
381-2 18” Coax Cable
381-12 12’ Coax Extension
381-25 25’ Coax Extension
383 Dual Band Antenna (included)
386 Antenna Mounting Bracket
Compatibility
XR100/XR500 Version 213 or higher
Certifications
FCC Part 15: RI7ME910C1NV
Industry Canada: 5131A-ME910C1NV
INTRUSION FIRE ACCESS NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
888-436-7832 | DMP.com
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
The antenna used for this transmitter must be installed to provide a separation distance of at least 20cm (7.874 in.) from all persons. It must not be located or operated
in conjunction with any other antenna or transmitter.
Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Information
This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be
installed at a minimum separation distance from the antenna to a general bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de sécurité 6 de Santé
Canada. Le système doit être installé à une distance minimale de 7.87 pouces (20 cm) séparant l’antenne d’une personne présente en conformité avec les limites
permises d’exposition du grand public.
TEST THE 263LTE-V5
Confirmed Faulty
MODEM OPERATING NO MODEM FOUND
IDENTIFIED NO SIM CARD
TOWER DETECTED NO TOWER
REGISTERED NOT REGISTERED
CONNECT SUCCESS
CONNECT ERROR
NOT ACTIVATED
CELL PATH GOOD NO ACK RECEIVED
Table 1: Cell Status Test Results
The panel provides a diagnostic function to test the communication integrity and cellular signal strength of the 26LTE-V5 to
the nearest tower for the cellular carrier. To use the diagnostic function, reset the panel, enter 2313 (DIAG), and press CMD.
Communication Status
This option tests the individual components of cellular or wireless
network communication.
1. Select CELL STATUS from the Diagnostic menu.
Possible test results are shown in Table 1.
2. Select YES to continue through the remaining
component tests or select NO to stop testing and
return to CELL STATUS.
3
  • Page 1 1
  • Page 2 2

Digital Monitoring Products LT 1873 Installation & Programming Guides

Taper
Installation & Programming Guides

dans d''autres langues