Lennox LMDTV-3328CNM Manuel utilisateur

Marque: Lennox

Modèle: LMDTV-3328CNM

Catégorie: Cheminées

Taper: Manuel utilisateur

CARE AND OPERATION

INSTRUCTIONS

OTL Report No. 116-F-31-5

A French manual is available upon request. Order P/N 875,028CF

Ce manuel d’installation est disponible en francais, simplement en

faire la demande. Numéro de la pièce 875,028CF

Millivolt Models Electronic Models

MODELS

DIRECT VENT MERIT

™

LMDV-33/35/40 SERIES

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

LMDVT-3328CNM

LMDVT-3328CPM

LMDVR-3328CNM

LMDVR-3328CPM

LMDVT-3328CNE

LMDVR-3328CNE

LMDV-3530CNE

LMDV-4035CNE

LMDV-3530CNM

LMDV-3530CPM

LMDV-4035CNM

LMDV-4035CPM

DIRECT-VENT GAS FIREPLACE HEATERS

P/N 875,028M REV. E 02/2008

Do not store or use gasoline or other ﬂammable

vapors or liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not light any appliance.

• Do not touch any electrical switch; do not

Use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow your gas supplier's

instructions.

• If your gas supplier cannot be reached, call

the ﬁre department.

Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING: IF THE INFORMATION IN THIS MANUAL

IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAMAGE,

PERSONAL INJURY OR LOSS OF LIFE.

WARNINGS

•

Hot! Do not touch! The glass and

surfaces of this appliance will be hot

during operation and will retain heat

for a while after shutting off the appli-

ance. Severe burns may result.

•

Carefully supervise children in the

same room as appliance.

•

If small children are present in the home, it is

recommended that this appliance be ﬁtted with

a screen door or screen panel kit. See

Pages

13 & 14 for ordering information.

POUR VOTRE SÉCURITÉ: Ne pas entreposer ni

utiliser d'essence ni d'autre vapeurs ou liquides

inﬂammables dans le voisinage de cet appareil ou

de tout autre appareil.

POUR VOTRE SÉCURITÉ: Que faire si vous sentez

une odeur de gaz:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas vous

servir des téléphones se trouvant dans le bati-

ment où vous vous trouvez.

• Evacuez la piéce, le bâtiment ou la zone.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions

du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de

gaz, appelez le service dos incendies.

L'installation et service doit être exécuté par un

qualiﬁé installeur, agence de service ou le fournis-

seur de gaz.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN

SUIVRE LES INSTRUCTIONS DONNÉ DANS CETTE

NOTICE POUR RÉDUIRE AU MINIMUM LE RISQUE

D'INCENDIE OU POUR ÉVITER TOUT DOMMAGE

MATÉRIEL, TOUTE BLESSURE OU LA MORT.

The Electronic appliances have an electronic

intermittent pilot system provides safe, efﬁcient

operation. External electrical power is required

to operate these appliances.

These appliances comply with National Safety

Standards and are tested and listed by Omni-

Test Laboratories (Report No. 116-F-31-5) to

ANSI ZZ21.88b (in Canada, CSA-2.33b), and

CAN/CGA-2.17-M91 in both USA and Canada,

as vented gas ﬁreplace heaters.

The Installation must conform to local codes

or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1/NFPA

54-latest edition, or the Natural Gas and

Propane Installation Code, CSA B149.1-latest

edition. The appliance, when installed, must

be electrically grounded in accordance with

local codes or, in the absence of local codes,

the latest edition of the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical Code,

CSA C22.1 - latest editions.

GENERAL INFORMATION

Note: Installation and repair should be per-

formed by a qualiﬁed service person. The

appliance should be inspected annually by a

qualiﬁed professional service technician. More

frequent inspections and cleanings may be

required due to excessive lint from carpeting,

bedding material, etc.

It is imperative that the control compartment,

burners and circulating air passage ways of

appliance be kept clean. See Maintenance

instructions on Page 5.

S'assurer que le brùleur et le compartiment des

commandes sont propres. Voir les instructions

d'installation et d'utilisation qui accompagnent

l'appareil.

Provide adequate clearances around air open

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front openings of the appliance.

Due to high temperatures the appliance should

be located out of trafﬁc and away from furniture

and draperies. Locate furniture and window

coverings accordingly.

These ﬁreplaces are designed as supplemental

heaters. Therefore, it is advisable to have an alter

nate heat source when installed in a dwelling.

Input (BTU) MAnnually-Modulated Gas

Valves (millivolt models)

NATURAL GAS

Models Input Rate

(BTU/HR)

LMDVT-3328CNM

LMDVR-3328CNM

17,500 high

11,700 low

LMDV-3530CNM

20,000 high

12,800 low

LMDV-4035CNM

27,000 high

18,500 low

Table 1

Input (BTU) MAnnually-Modulated Gas

Valves (millivolt models)

PROPANE GAS

Models Input Rate

(BTU/HR)

LMDVT-3328CPM

LMDVR-3328CPM

17,500 high

14,000 low

LMDV-3530CPM

20,000 high

15,200 low

LMDV-4035CPM

27,000 high

21,500 low

Table 2

Input (BTU) - Fixed Rate

(electronic models)

NATURAL GAS & PROPANE GAS

Models Input Rate

(BTU/HR)

LMDVT-3328CNE

LMDVR-3328CNE

17,500

LMDV-3530CNE

20,000

LMDV-4035CNM

LMDV-4035CPM

28,000

Table 3

TABLE OF CONTENTS

Introduction ......................................Page 2

General Information ..........................

Page 2

Gas Controls Access .........................

Page 3

Operation/Care of Your Appliance .....

Page 3

Variable Flame Adjustment ................

Page 4

Maintenance ......................................Page 5

Front Glass Enclosure Panel,

Removal and Installation .................

Page 6

Install Vermiculite, Volcanic Stone,

Embers & Logs .................................

Page 7

Burner Flame Appearance & Sooting

Page 10

Burner Flame Adjustments ................

Page 10

Millivolt Appliance Checkout .............

Page 11

Electronic Appliance Checkout ..........

Page 11

Product Reference Information .........

Page 11

Warranty ...........................................Page 11

Wiring Diagrams ...............................

Page 12

Accessory Components ....................

Page 13

Lighting Instructions – Millivolt ........

Page 18

Lighting Instructions – Electronic .....

Page 20

Maintenance Schedule ......................

Page 22

Troubleshooting Guide – Millivolt

......Page 23

Troubleshooting Guide – Electronic ..

Page 23

Replacement Parts List .....................

Page 26

CONGRATULATIONS!

In selecting this LENNOX Direct-Vent Gas Appliance you have chosen the ﬁnest and most

dependable ﬁreplace to be found anywhere. Its a beautiful, prestigious alternative to a

wood burning ﬁreplace. Welcome to a Family of tens of thousands of satisﬁed LENNOX

Fireplace Owners.

Please carefully read and follow all of the instructions found in this manual. Please pay

special attention to the safety instructions provided in this manual. The Homeowner's

Care and Operation Instructions included here will assure that you have many years of

dependable and enjoyable service from your LENNOX product.

INTRODUCTION

The Fireplace models covered in this manual

are Direct-Vent sealed combustion gas ﬁreplace

heaters designed for residential application.

Direct-Vent appliances operate with the com-

bustion chamber completely isolated from the

indoor environment. All air for combustion is

brought in from the outside and exhaust gases

are vented through the same direct vent, co-axial

(intake/exhaust) vent system.

The Millivolt appliances have a millivolt gas

control valve with piezo ignition system provides

safe, efﬁcient operation. If any optional acces-

sories which require electrical power are being

installed, the electrical power must be provided

at the time of appliance installation.

These appliances are designed to operate on natural

gas or propane gas only. The use of other fuels or

combination of fuels will degrade the performance

of this system and may be dangerous.

Millivolt Models - BTU Input

Millivolt models come standard with the manu

ally-modulated gas valve; ﬂame appearance and

heat output can be controlled at the gas valve.

The BTU Input for millivolt models is shown in

Tables 1 & 2:

Electronic Models -

Electronic models have a ﬁxed rate gas valve.

The BTU Input for electronic models is shown

Table 3:

This manual is part of a set of two supporting

this product. Refer to manual 850,029M for

Installation Instructions.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Burner Oriﬁce Sizes

Elevation 0-4500 feet ( 0-1372 meters)

Model

Series

Natural

Gas

drill size

(inches)

Propane

Gas

drill size (inches)

LMDVT-3328

LMDVR-3328

#45 (.082")

39L66 •

1.2 mm (.048")

99K78 •

LMDV-3530

#44 (.086")

60J80 •

#55 (.052")

19L52 •

LMDV-4035

#37 (.104")

24M10 •

1/16"

(.0625")

21L01 •

* Standard size installed at factory

• Part /Cat. Number

Table 7

Inlet Gas Supply Pressure

(all models)

Fuel # Minimum Maximum

Natural Gas

5.0" WC

(1.24 kPa)

10.5" WC

(2.61 kPa)

Propane

11.0" WC

(2.74 kPa)

13.0" WC

(3.23 kPa)

Table 4

Burn-in Period

During the ﬁrst few ﬁres of this appliance there

will be some odor due to the curing of the

paint and burning off of lubricants used in the

manufacturing process.

Depending on your use, the burn-in period may

take a few hours or a few days.

KEEP YOUR HOUSE WELL VENTILATED

DURING THE CURING PROCESS. THE ODOR

AND HAZE EMITTED DURING THE CURING

PROCESS CAN BE QUITE NOTICEABLE AND

MAY SET OFF A SMOKE DETECTOR.

If an optional blower is installed, Do not turn it

on during the Burn-In period.

A white ﬁlm may develop on the glass front

during the ﬁrst few ﬁres as part of the curing

process. The glass should be kept clean during

the ﬁrst two weeks of use to prevent the ﬁlm from

baking on (making it very difﬁcult to remove).

See

Cleaning Glass on Page 5.

These appliances and their individual shut-off

valves

must be disconnected from the gas

supply piping system during any pressure

testing of that system at pressures

greater

than 1/2 psig (3.5 kPa).

These appliances must be isolated from the

gas supply piping system (

by closing their

individual manual shut-off valve) during any

pressure testing of the gas supply piping

system at test pressures equal to or

less than

1/2 psig (3.5 kPa).

At the time of installation, it must be determined

if the appliance needs to be derated. Contact

your local gas supplier for deration requirements

for your area.

Deration - At higher elevations, the amount of

BTU fuel value delivered must be reduced by

either using gas that has been derated by the gas

company or by changing the burner oriﬁce to a

smaller size as regulated by the local authorities

having jurisdiction and by the (USA) National

Fuel Gas Code NFPA 54/ANSI Z223.1 - latest

edition or, in Canada, the CAN1-B149.1 and .2

codes - latest edition.

Gas Pressure -

Tables 4, 5 and 6 show the appliances' gas

pressure requirements.

Manifold Gas Supply Pressure

(millivolt models)

Fuel # Low High

Natural

Gas

(Lo) 2.2" WC

(.55 kPa)

(Hi) 3.5" WC

(.87 kPa)

Propane

(Lo) 6.3" WC

(1.57 kPa)

(Hi) 10.0" WC

(2.49 kPa)

Table 5

Manifold Gas Supply Pressure

(electronic models)

Fuel # Fixed

Natural Gas

3.5" WC

(.87 kPa)

Propane

10.0" WC

(2.49 kPa)

Table 6

Test gauge connections are provided on the

front of the millivolt gas control valve, identiﬁed

IN for the inlet and OUT for the manifold side

(see

Figures 4 or 5 on Page 4). A 1/8" NPT

Test gauge connection is provided at the inlet

and outlet (manifold) ports on the electronic gas

control valve (see

Figure 3 on Page 4).

Oriﬁce Sizes - Sea Level to High Altitude

(All Models): These appliances are tested and

approved for installations at elevations of 0-4500

feet (0-1372 meters) above sea level using the

standard burner oriﬁce sizes (marked with an

"*" in

Table 7).

Gas Controls/Control Compartment

Access

The gas controls can be found behind the control

compartment access door.

Removing Control Compartment Door:

Open the door by gently liftint it upward until the

hook catches on boths sides clear the locating

slots. Then pull door out to remove.

On millivolt systems, the piezo igniter, HI/LO

ﬂame adjustment knob, and pilot and main

gas OFF/ON control knob are located below

the glass panel enclosure. The gas valve for

electronic systems is also located below the

glass enclosure panel. See

Figure 1.

Reinstalling Control Compartment Door:

To reinstall, insert the hook catches on each side

of the door into the corresponding slots in the

control compartment opening, then gently push

forward and slide down until it locks in place.

Figure 1

OPENING CONTROL

COMPARTMENT DOOR

OPERATION AND CARE OF YOUR

APPLIANCE

The standard controls for appliance opera-

tion are located behind the panel below the

appliance front glass enclosure panel (see

Figure 1). Optional control switches are also

available (see

Page 13 - Remote Wall Switch,

Remote Control or Wall Thermostat).

Operation of millivolt and electronic gas con

trol systems are different. Before lighting and

operating your appliance determine if you have

a millivolt or electronic appliance. Familiarize

yourself with the gas control valve that your

appliance uses. Refer to

Figure 1 for access

to the gas control valve.

Control Valve

Lower Control

Compartment Door

Lift the Lower Control

Compartment Door

up and pull out to

remove.

Out

Hook Catch

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 2

Sit and Honeywell Millivolt Gas Valve

Showing Piezo Igniter Location (Each Unit is

Equipped with Only One of these Gas Valves)

Millivolt Appliances - Appliances with

Millivolt systems will be ﬁtted with the gas

control valve shown in Figures 4 or 5.

Electronic Appliances - Appliances with

electronic systems will be ﬁtted with the

electronic valve shown in

Figure 3.

Millivolt Appliances - To light millivolt appli-

ances refer to the detailed lighting instructions

found on Pages 18 & 19 . Millivolt appliance

lighting instructions may also be found on the

pull out lighting instruction labels attached to

the gas control valve.

Millivolt appliances are ﬁtted with an OFF/ON

Rocker Switch located behind the control

compartment access door, below the appli-

ance front glass enclosure panel (see Figure 2

for location). Once the pilot is lit, the OFF/ON

rocker switch will control the appliance OFF/ON

burner operation. To operate: Toggle the switch

between its ON and OFF positions.

If your millivolt appliance is equipped with an

optional remote switch kit (wall switch, remote

control or wall thermostat) and the pilot is lit,

the appliance main burner may be turned on

and off using the optional switch. When using

an optional remote switch, turn off the standard

OFF/ON switch.

Note: To prevent excessive resistance in burner

circuit (which can cause burner operation prob

lems), only one burner control switch should be

wired to valve. Therefore, if an optional control

switch is installed, the standard Off/On switch

and wires should be removed.

SIT Gas Valve

Shown with control

compartment door

removed

Piezo Igniter

Honeywell

Gas Valve

If your electronic appliance is equipped with an

optional remote wall switch or remote control kit

the appliance main burner may be turned on and

off with the wall switch or remote control.

If your electronic appliance is not equipped

with a wall switch or remote control, the main

burner must be turned off and on with the gas

control switch. Toggle the switch from ON to

OFF to operate the main burner .

Variable Flame Height Adjustment

(Millivolt Appliances only)

1. All Millivolt appliances are equipped with a

variable gas control valve. Flame height for

these models may be adjusted through a

range between ﬁxed low and high settings

while the appliance is in operation. Adjust

the ﬂame height as desired after lighting the

appliance by rotating the variable adjustment

control knob (HI/LO) located on the front of

the valve (refer to

Figures 4 & 5 ).

2. During the ﬁrst initial burns of these appli-

ances, there will be some odor emitted (see

Burn-In Period on Page 3 ).

Honeywell Millivolt Gas Valve

Figure 5

OFF

Figure 3

Optional Blower OFF/ON

Rocker Switch

SIT Millivolt Gas Valve

Gas

Outlet

Gas

Inlet

Pilot Adjustment

Screw

Terminals

TPTH,TP & TH

Figure 4

OUT

OFF

HI/LO Variable

Flame Height

Adjustment

Manifold Pressure Tap

Inlet Pressure Tap

Piezo Igniter

Main Gas

Control Knob

OFF/PILOT/ON

Piezo Igniter

Optional Burner OFF/ON

Rocker Switch

Piezo Igniter

Optional Blower OFF/ON

Rocker Switch

Optional Burner OFF/ON

Rocker Switch

HI/LO Variable

Flame Height

Adjustment

Main Gas

Control Knob

OFF/PILOT/ON

Manifold Pressure

Tap

Piezo Igniter

Inlet Pressure Tap

Gas

Outlet

Gas

Inlet

Honeywell Electronic Gas Valve

Manifold Pressure

Port

ON/OFF Switch

Inlet

Pressure

Port

Electronic Gas

Control Valve

Electronic Appliances -

To light electronic appliances refer to the detailed

lighting instructions found on

Pages 20 & 21

of these instructions. Electronic appliance

lighting instructions may also be found on the

pull out lighting instruction labels attached to

the gas control valve.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

3. Keep the lower control compartment clean

by vacuuming or brushing at least twice a

year. More frequent cleaning may be required

due to excessive lint from carpeting, bedding

materials, pet hair, etc. It is very important

that the control compartments, burners

and circulating air passageways of the

appliance are kept clean.

4. Always turn off gas to the pilot (millivolt

appliances) and let the appliance cool down

before cleaning. Before re-lighting, refer

to the lighting instructions in this manual.

Lighting instructions may also be found

on the pull out lighting instruction labels

attached to the gas control valve.

5. Always keep the appliance area clear and

free from combustible materials, gasoline

and other ﬂammable liquids.

6. Remember, Millivolt appliances have a continu-

ous burning pilot ﬂame. Exercise caution when

using products with combustible vapors.

Before re-lighting the ﬁreplace, refer to the

lighting instructions in this manual. Instruc

tions are also found on pull-out panels

located below the glass door in the control

compartment.

Inspect Venting System

The appliance and venting system should be

thoroughly inspected before initial use and

at least annually by a qualiﬁed service techni

cian (inspection should include ensuring that

exhaust or intake passages are unobstructed

and vent components are properly assembled

and not damaged).

WARNING

Turn off gas and electrical power

before servicing the appliance.

CAUTION

Wear gloves and safety Glasses

for protection while doing

required maintenance.

IMPORTANT

Always verify proper operation

after servicing.

MAINTENANCE

(See Maintenance Schedule,

Page 22)

Refer to the maintenance schedule for maintenance

tasks, procedures, periodicity and by whom they

should be performed. Always verify proper opera

tion of the appliance after servicing.

IMPORTANT

Do not use abrasive cleaners

on glass. Never clean the glass

when it is hot.

• During start-up, it is normal for condensa-

tion to form on the inside of the glass (this

condensation and fog will usually disappear

in a few minutes). The moisture can cause

lint, dust and other airborne particles to cling

to the glass surface.

• Initial curing of the high temperature paint

and burning off of lubricants used in the

manufacturing process may result in a ﬁlm

on the glass.

• A white coating may form on the glass as a

result of impurities and minerals in the fuel.

It is recommended that the glass be cleaned

two or three times during each heating season,

depending on the circumstances present. The

following cleaning solutions are approved for use

to clean glass:

• Non-ammonia based household cleaner

• 50%-50% mix of white vinegar & water

• Gas ﬁreplace/stove glass cleaner

Inspect Glass Gasket - Visually inspect the

gasket on the backside of the glass enclosure

panels. The gasket surface must be clean, free

of irregularities and seated ﬁrmly.

WARNING

Label all wires prior to discon-

nection when servicing con-

trols. Wiring errors can cause

improper and dangerous opera-

tion. Verify proper operation

after servicing.

Inspect and clean all wire connections. Ensure

that there is no melting or damage. Inspection

should include

• Terminals at the Valve

• OFF/ON Switch

• (Optional Control Switch) Wall Thermostat,

Remote Control or Remote Wall Switch Kit

Inspect Burner Flame Appearance

Ensure that the burner flame appearance

resembles the ﬂame shown in

Figures 10 &

11 and as described in Flame Appearance and

Sooting on Page 10. The Homeowner must

contact a qualiﬁed service technician at once

if any abnormal condition is observed.

Small Area Paint Touch-up

The ﬁnish of the appliance is a high-qual

ity powdercoat. Only use factory supplied

powdercoat paint kit for touch-ups. Paint is

available at your local authorized Lennox Hearth

Products dealer, cat. no. 90L74. Never attempt

to paint a hot ﬁreplace.

Do not attempt to repaint the appliance until the

ﬁnish is completely cured (see

Burn-In Period

Page 3 ). If the surface later becomes stained

or marred, it may be lightly sanded and touched

up with spray paint.

Clean Logs And Burner

Carefully remove the logs (use care when han

dling the ﬁber logs, as they become quite fragile

after curing). Vacuum out any foreign matter

(lint, carbon, etc). on the burner. Ensure the

burner ports are “open.” Remove any carbon

deposits from the under side of the logs using

a vacuum cleaner, or a soft bristled brush (i.e.

paint brush). Note: Improper positioning of

logs can create carbon build-up and will alter

the performance of the appliance.Replacing

Logs -

If the logs become damaged by accident or im

proper handling and need replacement, use only

the proper replacement logs from manufacturer

(see

Pages 26 & 27 for ordering information).

Re-Install Embers, Logs and Vermiculite

- Carefully follow placement instructions on

Pages 7 to 9 ). All logs should ﬁt onto cor-

responding pins and/or log stoppers. This will

ensure a proper ﬂame and safe combustion.

Inspect Wiring

Refer to wiring diagrams on

Page 12.

If the venting system is disassembled for any

reason, a qualiﬁed service technician should

follow vent installation instructions for proper

reassembly and proper sealing of the venting

system components. However, more frequent

periodic inspections and cleanings should be

performed by the homeowner.

Clean Lower Control Compartment

Keep lower control compartment clean by

vacuuming or brushing it out at least twice a

year (also clean the air venturi with a brush or

wire). More frequent cleaning may be required

due to accumulation of lint from carpeting,

bedding materials, pet hair, spider webs, etc. It

is very important that control compartments,

burners, circulating air passageways and air

venturi on the appliance are NOT obstructed

in any way.

Cleaning Glass

(see Front Glass Enclosure Panel, Removal and

Installation on Page 6 )

Note: Clean glass after ﬁrst two weeks of opera-

tion (after Burn-In period is over) and then only

when necessary and when the ﬁreplace is cool.

Wipe surface with clean, dampened, soft cloth.

Follow with dry, soft towel as desired. Take care

not to scratch the glass surface.

The viewing glass should be cleaned periodi

cally to remove any build-up caused from the

following:

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

WARNING

Handle this glass with extreme

care! Tempered glass is suscep-

tible to damage – do not scratch

or handle roughly while rein-

stalling the glass door frame.

Front Glass Enclosure Panel, Removal

and Installation

WARNING

Do not operate appliance with the

glass front removed, cracked or

broken. Replacement of the glass

should be done by a licensed or

qualiﬁed service technician.

WARNING

Do not attempt to substitute the

materials used on this door, or

replace cracked or broken glass

with any materials other than

those provided by the appliance

manufacturer.

WARNING

The glass door of this appli-

ance must only be replaced as a

complete unit as provided by the

manufacturer. Do not attempt to

replace broken, cracked or chipped

glass separately.

WARNING

Do not attempt to touch the front

enclosure glass with your hands

while the ﬁreplace is in use.

These are direct-vent appliances. They are

designed to operate only when the front glass

enclosure panel is installed. Generally the front

glass enclosure panel should not be removed

except to gain access to the components within

the ﬁrebox, and the appliance may only be op

erated without the front glass enclosure panel

in place for very brief periods of time during

appliance checkout and adjustment. Note: The

ﬂame appearance will be diminished while the

front glass enclosure panel is removed.

During this appliance checkout and adjust

ment period, a potential safety hazard exists

- EXERCISE EXTREME CAUTION to prevent

the occurrence of any burn injuries from the

exposed ﬂames or hot surfaces. Also note, that

while the front glass enclosure panel (or any of

the panels) is removed, the ﬂame appearance

will appear to be smaller than normal.

Figure 6 - INSTALLING GLASS DOOR

Top Flange on

Glass Door

Bottom Vee-ﬂange

Glass Door

Glass Door Latch

Glass Door

Firebox Floor

Removing Glass Enclosure Panels

(see Figure 6)

1. Remove the top louver assembly by pulling

it up and out.

2. Remove the control compartment access

door (see removal instructions on

Page 3

- Removing Control Compartment Door).

3. Locate the two (2) latches at the top of the

control compartment. To disengage the two

latches from the bottom vee-ﬂange of the

glass enclosure panel, reach for the handles

located towards the back of the latches and

pull the handles down toward the front of

the appliance.

4. Swing the bottom of the door out and raise

it slightly to lift the top ﬂange of the door

frame away from the appliance.

Installing Glass Enclosure Panels

(see Figure 6)

1. Visually inspect the gasket on the backside

of the glass panel. The gasket surface must

be clean, free of irregularities and seated

ﬁrmly.

2. Position the glass enclosure panel in front of

the ﬁrebox opening at a 45 degree angle and

engage the top ﬂange over the lip at the top

of the ﬁrebox opening.

See Figure 6.

3. Swing the glass enclosure panel down and

back. Ensure the gasket seats evenly as the

panel draws shut. Engage the Vee-ﬂange at

the bottom of the panel with the latches and

close the latches to secure the panel.

4. Reinstall the control compartment door

see installation instructions on

Page 3,

Reinstalling Control Compartment Door).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

WARNING

The size and position of the log

set was engineered to give the

appliance a safe, reliable and

attractive ﬂame pattern. Any

attempt to use a different log

set in the ﬁreplace will void

the warranty and will result in

incomplete combustion, soot-

ing, and poor ﬂame quality.

REFERENCE

Firebox Accessories/Parts

Cat. No. Model No. Description

88L53 FGE Bag of Glowing Embers

(1 oz. rockwool)

H3696

Vermiculite, Bag (2 liters)

80L42 FDVS

Bag of Decorative

Volcanic Stone

Table 8

Glowing Embers

Bag of Glowing

Embers (rockwool)

Separate into Quarter

Size (separate) Pieces

INSTALL VERMICULITE, VOLCANIC

STONE, GLOWING EMBERS AND LOGS

1. Remove the front glass enclosure panel

(see

Removing Glass Enclosure Panels on

this page).

Carefully remove the old logs, embers

volcanic stone and vermiculite from the

ﬁrebox. Handle logs carefully to prevent

breakage.

Install Vermiculite - Place some vermiculite

on the ﬁrebox ﬂoor around the burner (the

entire bag of vermiculite will NOT be used).

See

Figures 8 & 9. DO NOT PLACE ANY

VERMICULITE ON THE BURNER. Mound

up a portion of the vermiculite in front of the

burner.

4. Install decorative volcanic stone - Sprinkle

the decorative volcanic stone (dark colored)

on top of the vermiculite (light colored) in a

pleasing pattern (see

Figures 8 & 9).

5. Placement of Glowing Embers -

Separate the Embers (rockwool) into pieces

about the size of a quarter (see

Figure 7).

Keep the pieces ﬂuffed up, not matted.

Distribute these pieces over the surface of

the burner, as shown in

Figures 8 & 9. Do

not use more than is necessary. Ensure that

the main burner slots remain uncovered by

the ember material.

Note: This appliance is provided with enough

Glowing Embers for several applications, do

not use all that is in a new bag at one time. For

best glowing effect, replace the ember material

annually.

6. Placement of Logs and Twigs -

All logs that have locating notches or slots to

help ensure that they are properly positioned.

All top logs that rest on lower logs, do so

over notches, indents or pins. Proper twig

placement is critical to prevent sooting. Twigs

should be placed in the gaps between the ﬂame

peaks and should be positioned so they do not

impinge the ﬂames.

LMDV-3328 & LMDV-3530 - Install as Follows

Carefully position the ceramic ﬁber logs and twigs

over the burner as shown in

Figure 8. Logs

should be placed in the order shown and per the

following instructions.

WARNING

DO NOT attempt to install the logs

until the appliance installation

has been completed, the gas line

connected and tested for leaks

and the initial burner operation

has been checked out.

Figure 7

WARNING

This appliance is not designed

to burn wood. Any attempt to

do so could cause irreparable

damage to appliance and prove

hazardous to your safety.

WARNING

If logs are not installed according

to the log installation instruc-

tions, ﬂame impingement and

improper combustion could

occur and result in soot and/or

excessive production of carbon

monoxide (CO), a colorless,

odorless, toxic gas.

1. Place the rear log (A) as shown. Position the

2 notches on the bottom of the log over the

2 corresponding locating brackets against

the back wall of ﬁrebox.

2. Place the left log (B) as shown. The notch

on the bottom of the log should ﬁt over the

corresponding locating bracket.

3. Place the right log (E) as shown. The hole

on the back of the log should ﬁt over the

corresponding pin on the rear log (A). Make

sure that the log is positioned so it aligns

to the sides of the gas ports on the corner

of the burner.

4. Place the left center log (C) as shown.

The forked end of the log ﬁts into the cor

responding notch on rear log (A). The slot

on the other end (bottom) of log ﬁts over

the corresponding locating bracket on the

sub-ﬂoor.

5. Place the right center log (D) as shown. One

end of the log ﬁts into the corresponding

indent on the right log (E). The slot on

the other end (bottom) of log ﬁts over the

corresponding locating bracket on the sub-

ﬂoor.

LMDV-4035 - Install as Follows

Carefully position the ceramic ﬁber logs and twigs

over the burner as shown in

Figure 9. Logs

should be placed in the order shown and per the

following instructions.

1. Position the center log (C) onto the 2 cor

responding location pins on the burner.

2. Place the rear log (A) as shown. Position the

2 notches on the bottom of the log over the

2 corresponding locating brackets against

the back wall of ﬁrebox.

3. Place the left log (B) as shown. The notch

on the bottom of the log should ﬁt over the

corresponding locating bracket.

4. Place the right log (E) as shown. The notch

on the bottom of the log should ﬁt over the

corresponding locating bracket. Make sure

that the log is positioned so it aligns to the

sides of the gas ports on the corner of the

burner.

5. Place the center front log (D) as shown.

The slot in the bottom of the log ﬁts over

the corresponding location bracket on the

sub-ﬂoor.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 8

MODEL LMDV-3328 & LMDV-3530

Log Placement Instructions

Vermiculite

Volcanic

Stone

Embers

DO NOT PLACE EMBERS OVER GAS SLOTS

The 2 notches on log bottom rest on locating brackets

Notch

Slot ﬁts over bracket.

Hole on bot-

tom of log (E)

ﬁts over pin

on log (A).

V-Shape area of log (E) should

align to sides of burner ports

Log (C) ﬁts into

indent in Log (A)

Slot on bottom of Log

(D) ﬁts over bracket

Log (D) ﬁts

into indent

on Log (E)

LOG SET

Catalog Number

H3366

* Item

Description

Log, Rear

Log, Left

Log, Left Center

Log, Right Center

Log, Right

* Item "letters" above correspond to photos

Install the Embers, Vermiculite, Volcanic Stone and Logs in the order

shown here (1 through 6) and per the instructions on Page 7.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 9

MODEL LMDV-4035

Log Placement Instructions

Vermiculite

Volcanic

Stone

DO NOT PLACE EMBERS OVER GAS SLOTS

Embers

Place log over pins

Notch

The 2 notches

on log bottom

rest on locating

brackets

Notch on log bottom

ﬁts over bracket

Notch on log bottom

ﬁts over bracket

Slot on bottom of Log

(D) ﬁts over bracket

LOG SET

Catalog Number

H3365

* Item

Description

Log, Rear

Log, Left

Log, Center

Log, Center Front

Log, Right

* Item "letters" above correspond to photos

Install the Embers, Vermiculite, Volcanic Stone and Logs in

the order shown here (1 through 6) and per the instructions

on Page 7.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

BURNER ADJUSTMENTS

(QUALIFIED TECHNICIANS ONLY)

Flame Appearance and sooting

Proper ﬂame appearance is a ﬂame which is

blue at the base and becomes yellowish-orange

in the body of the ﬂame. When the appliance

is ﬁrst lit, the entire ﬂame may be blue and will

gradually turn yellowish-orange during the ﬁrst

15 minutes of operation. If after a short period

the ﬂame stays lowered blue, or if the ﬂame is

orange with evidence of sooting (black tip), the

air shutter opening may need to be adjusted.

If the air shutter openings closed too far, sooting

may develop. Sooting is indicated by black puffs

developing at the tips of very long orange ﬂames.

Sooting results in black deposits forming on the

logs, appliance inside surfaces and on exterior

surfaces adjacent to the vent termination. Soot

ing is caused by incomplete combustion in the

ﬂames and lack of combustion air entering the

air shutter opening. To achieve a warm yellow-

ish-orange ﬂame with an orange body that does

not soot, the shutter opening must be adjusted

between these two extremes.

Air Shutter Adjustment Guidelines

• If there is smoke or soot present, ﬁrst check

the log set positioning to ensure that the

ﬂames are not impinging on any of the logs.

If the log set is properly positioned and a

sooting condition still exists, then the air

shutter opening should be increased.

• The more offsets in the vent system, the larger

the air shutter opening will need to be.

• An appliance operated with the air shutter

opened too far, may have ﬂames that appear

blue and transparent. These weak, blue and

transparent ﬂames are termed anemic.

• Propane models may exhibit ﬂames which

candle or appear stringy. If this is present

and persists, adjust the air shutter to a more

open position, then operate the appliance for

a few more minutes to ensure that the ﬂame

normalizes and the ﬂames do not appear

sooty.

The following chart is provided to aid you in

achieving the correct air shutter adjustment

for your installation.

Air Shutter Adjustment Guidelines:

Amount of

Primary Air

Flame

Color

Air Shutter

Adjustment

If air shutter is

closed too far

Flame will

be orange

Air shutter

gap should be

increased

If air shutter is

open too far

Flame will

be blue

Air shutter

gap should be

decreased

Figure 10 - Burner Flame Appearance Model LMDV-3328 & LMDV-3530

Figure 11 - Burner Flame Appearance Model LMDV-4035

WARNING

Air shutter adjustment should

only be performed by a qualiﬁed

professional service technician.

WARNING

Ensure front glass panel is in place

and sealed during adjustment.

CAUTION

The air shutter door and nearby

appliance surfaces are hot. Exer

cise caution to avoid injury while

adjusting ﬂame appearance.

Burner Air Shutter Adjustment Procedure

1. Locate adjustment rod and adjust air shutter

to the standard setting as shown in

Figure

12 (adjustment rod is located in the lower

control compartment).

Note: Rotating the

adjustment rod clockwise decreases air and

counterclockwise increases air.

2. Light appliance (follow lighting procedure on

lighting label in control compartment or see

homeowners manual).

3. Allow the burner to operate for at least 15 min

utes while observing the ﬂame continuously

to ensure that the proper ﬂame appearance

has been achieved (see

Figure 10 or 11). If

the following conditions are present, adjust

accordingly.

• If ﬂame appears weak or sooty, adjust

the air shutter, incrementally, to a more

open position until the proper ﬂame

appearance is achieved.

• If ﬂame stays lowered blue, adjust the

air shutter, incrementally, to a more

closed position until the proper ﬂame

appearance is achieved.

4. Leave the control knob (off/pilot/on) in the

ON position and the burner OFF/ON switch

OFF (& remote switches, if applicable).

5. When satisﬁed that the burner ﬂame ap-

pearance is normal, close the lower control

compartment door.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Main Burner Factory Air Shutter

Opening Setting - Inches (millimeter)

Model Natural

Gas

Propane

Gas

LMDVT-3328

1/16"

(1.58 mm)

1/4"

(6.35 mm)

LMDVR-3328

1/16"

(1.58 mm)

1/4"

(6.35 mm)

LMDV-3530

1/16"

(1.58 mm)

5/16"

(7.94 mm)

LMDV-4035

1/8"

(3.18mm)

3/8"

(9.53 mm)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 12

CAUTION

Carbon will be produced if the air

shutter is closed too much. Any

damage due to carboning result-

ing from improperly setting the

air shutter is not covered under

the warranty.

Burner Air Shutter Adjustment

Adjustment Rod Up

(Fully Open Position)

Air Shutter

Adjustment Rod Down

(minimum air opening

position)

Burner Tube

Adjustment Set-Screw

Electronic Appliance Checkout

To light the burner, refer to the lighting instruc

tions on Pages 20 & 21. Ensure the igniter

lights the pilot. The pilot ﬂame should engulf

the ﬂame sensor as shown in

Figure 15.

With proper care and maintenance, your appli

ance will provide many years of enjoyment. If

you should experience any problem, ﬁrst refer

to the troubleshooting guide in this manual.

If problem persists, contact your Lennox

distributor.

Figure 15

3/8" to 1/2"

(9 -13 mm)

Ground

Electrode

Flame Rod

Hot Surface

Igniter

Proper Flame

Adjustment

Pilot

Nozzels

ELECTRONIC PILOT ASSEMBLY

Proper Pilot Flame Appearance

Figure 13

Thermocouple

Thermopile

Pilot

Nozzels

SIT MILLIVOLT PILOT ASSEMBLY

3/8" Min.

(9 mm)

Igniter Rod

Hood

Proper Pilot Flame Appearance

Figure 14

Proper Pilot Flame Appearance

Thermocouple

Thermopile

Pilot

Nozzels

3/8" Min.

(9 mm)

1/8" Min.

(3 mm)

Igniter Rod

Hood

HONEYWELL MILLIVOLT PILOT ASSEMBLY

Millivolt Appliance Checkout

The pilot ﬂame should be steady, not lifting

or ﬂoating. Flame should be blue in color with

traces of orange at the outer edge.

The top 3/8" (10 mm) at the pilot generator

(thermopile) and the top 1/8" minimum (tip)

of the quick drop out thermocouple should be

engulfed in the pilot ﬂame. The ﬂame should

project 1" (25 mm) beyond the hood at all three

ports. See

Figures 13 or 14.

To light the burner, refer to the lighting instruc

tions on

Pages 18 & 19.

Ref. Air shutter Patent:

U.S. Pat. 5,553,603

WARRANTY

Your gas appliance is covered by a limited

twenty year warranty. You will ﬁnd a copy

of the warranty accompanying this manual.

Please read the warranty to be familiar with

its coverage.

Retain this manual. File it with your other

documents for future reference.

PRODUCT REFERENCE INFORMATION

We recommend that you record the following im-

portant information about your ﬁreplace. Please

contact your Lennox dealer for any questions

or concerns. For the number of your nearest

Lennox dealer, please call 1-800-9-LENNOX

REPLACEMENT PARTS

A complete parts list is found at the end of

this manual. Use only parts supplied from the

manufacturer.

Normally, all parts should be ordered through

your Lennox distributor or dealer. Parts will be

shipped at prevailing prices at time of order.

When ordering repair parts, always give the

following information:

1. The model number of the appliance.

2. The serial number of the appliance.

3. The part number.

4. The description of the part.

5. The quantity required.

6. The installation date of the appliance.

If you encounter any problems or have any ques-

tions concerning the installation or application

of this system, please contact your distributor,

or Lennox directly:

LENNOX HEARTH PRODUCTS

1110 West Taft Avenue

Orange, CA 92865

visit us at www.Lennox.com

Your Fireplace's Model Number ________________________________________

Your Fireplace's Serial Number ________________________________________

The Date On Which Your Fireplace Was Installed ___________________________

The Type of Gas Your Fireplace Uses ____________________________________

Your Dealer's Name ________________________________________________

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

WIRING DIAGRAMS

Wiring diagrams are provided here for refer-

ence purposes only. This information is also

provided on schematics attached directly to the

appliance on a pullout panel located within the

control compartment.

Thermopile

If any of the original wire as supplied must

be replaced, it must be replaced with Type

AWM 105

C - 18 gage wire.

* Optional Kits Installed - OFF/ON wall switch,

wall thermostat or remote control receiver.

Note: Turn the appliance-mounted OFF/ON

burner control switch to the OFF position if

any of these kits are installed.

Millivolt Wiring Diagram

Schematic Representation Only

Field Wired

Factory

Wired

*Optional Switch

Standard OFF/ON Switch

CAUTION

Label all wires prior to discon-

nection when servicing con-

trols. Wiring errors can cause

improper and dangerous appli-

ance operation.

Figure 16

Figure 17

Electronic Wiring Diagram (Honeywell) Showing Blower Wiring for Optional FBK-100, FBK-200 & FBK-250 Kits

Schematic Representation Only

Relay Module C/W FBK-250 only. Plug blower

into J-Box receptacle for FBK-100 or FBK-200

application. See View A for J-Box wiring.

Optional Blower

*OFF/ON Switch

(Integral with

Gas Valve)

Honeywell

Electronic

Gas

Valve

120 VAC

Primary

Secondary

Optional Control Switch

Junction Box

Pilot Burner

Assembly

Field Wired

Factory

Wired

BK = BLACK BL = BLUE

R = RED W = WHITE

G = GREEN

GROUND

24 V

Transformer

View A

J-Box Wiring when

using unit mounted

relay module.

Igniter

Connector

* Leave the OFF/ON switch, which is

integral with the gas valve, in the ON

position.

**Optional Control Switches: Wall

Switch, Wall Thermostat or Remote

Control Receiver.

Notes:

1. If any of the original wire as supplied

must be replaced, use Type AWM 105°C

- 18 gage wire ONLY.

2. 120 VAC, 60 Hz - Less than 3 Amps.

Caution: label all wires prior to

disconnection when servicing controls.

Wiring errors can cause improper and

dangerous operation.

Junction Box

Tab Intact

Tab

Broken

Plug blower

into this

receptacle

* Wall-mounted

ON/ OFF Blower

Switch or Variable

Speed Control Switch.

Blower

Ground

lar

120 VAC - Black

Green

Ground

Screw

White

Green

Neutral

Side of

Receptacle

Hot

Side of

Receptacle

Red

Black

J-BOX WIRING FOR

WALL SWITCH

BLOWER CONTROL

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

ACCESSORY COMPONENTS

Remote Control Kit, Standard

Cat. No. Model No. Description

H0249 RCL Remote Control System

(Standard)

(ref. Form # 750,127M)

Remote Control Kit, Deluxe

Cat. No. Model No. Description

H0251 RCL-STAT Remote Control System

(Deluxe)

(ref. Form # 750,129M)

(ref. Form # 750,037M)

Digital Wall Thermostat

The wall thermostat kit provides temperature control

for optimum comfort.

Wall Thermostat, Millivolt

Cat. No. Model No. Description

H4635 DWTK Wall Thermostat Kit,

White

Product Reference Information

Cat.

No.

Model Ship.

Weight

Ship.

Volumn

H3313 LMDVT-3328CNM 95 lb. 13.08 cu. ft.

H3314 LMDVT-3328CPM 95 lb. 13.08 cu. ft.

H3315 LMDVR-3328CNM 95 lb. 13.08 cu. ft.

H3316 LMDVR-3328CPM 95 lb. 13.08 cu. ft.

H3317 LMDVT-3328CNE 95 lb. 13.08 cu. ft.

H3318 LMDVR-3328CNE 95 lb. 13.08 cu. ft.

H3319 LMDV-3530CNM 113 lb. 15.75 cu. ft.

H3320 LMDV-3530CPM 113 lb. 15.75 cu. ft.

H3321 LMDV-3530CNE 113 lb. 15.75 cu. ft.

H3322 LMDV-4035CNM 147 lb. 20.18 cu. ft.

H3323 LMDV-4035CPM 147 lb. 20.18 cu. ft.

H3324 LMDV-4035CNE 147 lb. 20.18 cu. ft.

Rocker Switch Kit

Cat. No. Model No. Description

80L41 FRS Rocker Switch Kit

Arch Door Kit - Polished Brass

Cat. No.

Model Fireplace Model

98L05 ADK33CPB

LMDVT-3328,

LMDVR-3328

26M43 ADK35CMPB LMDV-3530

81L35 ADK40CPB LMDV-4035

Arch Door Kit - Brushed Stainless Steel

Cat. No.

Model Fireplace Model

98L62 ADK33CBS

LMDVT-3328,

LMDVR-3328

26M44 ADK35CMBS LMDV-3530

98L69 ADK40CBS LMDV-4035

Arch Door Kits

The arch door kits are easy to install and do not re-

quire hardware to attach them to the standard door

frame. The decorative arch kits can not be used in

conjunction with the screen panel kit.

(ref. Form # 750,021M)

Unit-Mountable Rocker Switch

This rocker switch kit can be installed directly in

the gas valve mounting bracket (millivolt gas valve

equipped ﬁreplaces) to provide On/Off operation in

lieu of a wall switch.

Standard Remote Control System

The Model RCL (Standard) Remote Control System,

features a simplistic OFF/ON control function for the

ﬁreplace. This model includes a hand-held transmitter,

a remote receiver with wall-mount cover plate and

all hardware required to install the unit. The remote

receiver can be wall or hearth mounted.

The transmitter has ON and OFF functions that are

activated by pressing either button on the face of

the transmitter. When a button on the transmitter

is pressed, a signal light illuminates brieﬂy to verify

that a signal has been sent.

The Model RCL is designed to operate with all mil

livolt ignition systems, as well as electronic ignition

systems. It may be installed with use for either

natural gas or propane gas appliances. The RCL

offers ease of installation and allows you to execute

on-off commands to the ﬁreplace effortlessly with

one simple motion.

The Model RCL comes complete with detailed operat

ing instructions.

Deluxe Remote Control System

The Model RCL-T (Deluxe) Remote Control System

has all of the features of the standard system along

with an added easy to read LCD screen which presents

access to many enhancements, including; battery

power level indicator, timer, mode of operation,

thermostatic display including room temperature in

either metric of English units, ﬂame indicator and

clock. Fully programmable, the Model RCL-T allows

for virtual command over nearly all operational and

temperature variables, using the hand held remote

control transmitter.

The Model RCL-T (Deluxe) remote control system

is installed in the same manner as the standard

system, may be operated with electronic and mil-

livolt systems with either natural gas or propane gas.

The RCL-T comes complete with detailed operating

instructions.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Style View Screen Doors -

These Style View screen doors come in 4 beautiful styles. The Style View door installs over the standard glass

enclosure panel and provides a barrier to prevent direct contact with the hot glass surface. The door includes

heavy duty magnet door latches and functional twin-pane screen doors.

(ref. Form # 775,169M)

Style View™ Doors - Arch Design Kits

Cat. No. Model Model Model

Series

H0858 AD35C 35” Arch Doors, Charcoal

LMDV-3530

H0859 AD35TI 35” Arch Doors, Textured Iron

H0860 AD35SP 35” Arch Doors, Satin Pewter

H0861 AD35AB 35” Arch Doors, Antique Brass

H0862 AD40C 40” Arch Doors, Charcoal

LMDV-4035

H0863 AD40TI 40” Arch Doors, Textured Iron

H0864 AD40SP 40” Arch Doors, Satin Pewter

H0865 AD40AB 40” Arch Doors, Antique Brass

Style View Doors - Arch Pane Design Kits

H0930 APD35C 35” Arch Pane Doors, Charcoal

LMDV-3530

H0931 APD35TI 35” Arch Pane Doors, Textured Iron

H0932 APD35SP 35” Arch Pane Doors, Satin Pewter

H0933 APD35AB 35” Arch Pane Doors, Antique Brass

H0934 APD40C 40” Arch Pane Doors, Charcoal

LMDV-4035

H0935 APD40TI 40” Arch Pane Doors, Textured Iron

H0936 APD40SP 40” Arch Pane Doors, Satin Pewter

H0937 APD40AB 40” Arch Pane Doors, Antique Brass

Style View Doors - Square Design Kits

H0946 SD35C 35” Sq. Doors, Charcoal

LMDV-3530

H0947 SD35TI 35” Sq. Doors, Textured Iron

H0948 SD35SP 35” Sq. Doors, Satin Pewter

H0949 SD35AB 35” Sq. Doors, Antique Brass

H0950 SD40C 40” Sq. Doors, Charcoal

LMDV-4035

H0951 SD40TI 40” Sq. Doors, Textured Iron

H0952 SD40SP 40” Sq. Doors, Satin Pewter

H0953 SD40AB 40” Sq. Doors, Antique Brass

Style View Doors - Square Pane Design Kits

H0962 SPD35C 35” Sq. Pane Doors, Charcoal

LMDV-3530

H0963 SPD35TI 35” Sq. Pane Doors, Textured Iron

H0964 SPD35SP 35” Sq. Pane Doors, Satin Pewter

H0965 SPD35AB 35” Sq. Pane Doors, Antique Brass

H0966 SPD40C 40” Sq. Pane Doors, Charcoal

LMDV-4035

H0967 SPD40TI 40” Sq. Pane Doors, Textured Iron

H0968 SPD40SP 40” Sq. Pane Doors, Satin Pewter

H0969 SPD40AB 40” Sq. Pane Doors, Antique Brass

Arch Design

Arch Pane Design

Square Design

Square Pane Design

ACCESSORY COMPONENTS

(ref. Form # 750,101M)

Screen Panel Kits

Cat. No. Model No. Models Where Used

98L04 HG33

LMDVT-3328

LMDVR-3328

26M48 HG35M LMDV-3530

26M49 HG40M LMDV-4035

Decorative Arch Screen Panel Kit

Cat. No.

Model Model Model Series

H3592 DASPK33TI 33” Decorative Arch Screen Panel LMDVT-3328 & LMDVR-3328

H3593 DASPK35TI 35” Decorative Arch Screen Panel LMDV-3530

H3594 DASPK40TI 40” Decorative Arch Screen Panel LMDV-4035

(ref. Form # 750,199M)

Decorative Arch Screen Panel Kit

This easy to install optional screen panel installs over

the standard glass enclosure panel and provides a bar

rier to prevent direct contact with the hot glass surface.

These screen panels cannot be used in conjunction

with the arch door kits or door frame kits.

Barrier Screen Panel Kit

This easy to install optional screen panel installs over

the standard glass enclosure panel and provides a bar

rier to prevent direct contact with the hot glass surface.

These screen panels cannot be used in conjunction

with the arch door kits or door frame kits.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

3 Piece Trim Kit

Cat. No. Model No. Description

H0453 TK33PB3

33” Polished Brass,

LMDVT-3328, LMDVR-3328

96K21 TK35PB3

35” Polished Brass,

LMDV-3530

96K22 TK40PB3

40" Polished Brass,

LMDV-4035

H1813 TK33BS3

33” Brushed Stainless,

LMDVT-3328, LMDVR-3328

H1815 TK35BS3

35” Brushed Stainless,

LMDV-3530

H1816

TK40BS3

40", Brushed Stainless,

LMDV-4035

H4820 TK33C3

33” Charcoal,

LMDVT-3328, LMDVR-3328

H4821 TK35C3

35” Charcoal,

LMDV-3530

H4823 TK40C3

40" Charcoal,

LMDV-4035

(ref. Form # 750,147M)

4 Piece Trim Kit

Cat. No. Model No. Description

96K17 TK35PB4

35” 4 Piece Finish Trim Kit,

Polished Brass, LMDV-3530

96K18 TK40PB4

40” 4 Piece Finish Trim Kit,

Polished Brass, LMDV-4035

(ref. Form # ii-9299)

Bag of Glowing Embers

Bag of Volcanic Stone

Replacement ember materi-

als or volcanic stone are

available for use with these

appliances. Order kits as part

of the periodic maintenance

of the appliance.

Decorative Firebox Accessories

(all models)

Cat. No. Model No. Description

88L53 FGE

Bag of Glowing Embers

(1 oz. rockwool)

80L42 FDVS

Bag of Decorative

Volcanic Stone

(FDVS ref. Form #750,010M)

Forced Air Kit

The FBK-100 blower provides constant velocity forced

air circulation. The FBK-200 assembly with variable

speed, wall-mountable switch provides variable speed

forced air circulation. The FBK-250 assembly with

variable speed unit-mountable switch, also provides

variable speed forced air circulation.

Forced Air Blower Kits

Cat.

No.

Model No. Description

80L84 FBK-100 Blower, Standard

(single speed)

80L85 FBK-200 Blower, Variable Speed

(w/wall-mounted switch)

80L86 FBK-250 Blower, Variable Speed

(w/unit-mounted switch)

94L89 FBK-100-36 Blower, Standard, 36 Pack

94L90 FBK-200-36 Blower Kit - Variable Speed

with Wall Switch 36 Pack

H0543 FBK-250-36 Blower Kit - Variable Speed

with Thermo Snap Switch

36 Pack

(ref. Form # 750,028M & 750,029M)

Variable Speed Wall

Switch

Provides variable speed

control if optional blower kit

is purchased.

Variable Speed Wall Switch

Cat. No. Model No. Description

045571H VSWS Rocker Switch Kit

Brickaded Wall Liner Kits

Cat. No. Model No. Description

H0912 MBLK-33T

Brick Liner Kit, Top Vent,

LMDVT-3328

H0918 MBLK-33R

Brick Liner Kit, Rear Vent,

LMDVR-3328

H0913 MBLK-35

Brick Liner Kit, Top/Rear,

LMDV-3530

H0914 MBLK-40

Brick Liner Kit, Top/Rear,

LMDV-4035

Brickaded Panel Liner Kit

The brickaded liner kits include ceramic panels as

shown here. The panels have brick-like features in relief.

(ref. Form # 750,160M)

Polished Brass 3-Piece Trim Kit

This kit contains brass trim pieces used to ﬁnish the

gaps between the wall board and the ﬁreplace, provid

ing the appliance a brass perimeter highlight. This kit

contains the trim pieces and these instructions

Polished Brass 4-Piece Trim Kit

This kit contains brass trim pieces used to ﬁnish the

gaps between the wall board and the ﬁreplace, provid

ing the appliance a brass perimeter highlight. This kit

contains the trim pieces and these instructions

ACCESSORY COMPONENTS

OFF/ON Wall Switch Kit

The OFF/ON wall switch kit may be used to control

the operation of the ﬁreplace burner. Install the

OFF/ON wall switch in a convenient location near

the ﬁreplace.

White Wall Switch Kit

Cat. No. Model No. Description

85L87 FWSK OFF/ON Wall Switch Kit

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

ACCESSORY COMPONENTS

* Assembled 8-Piece Louver Kits

Polished Brass Brushed Stainless Models

Where Used

Cat. #

Model Cat. # Model

H1522 LK-400B H1523 LK-400BS

LMDVT-3328

LMDVR-3328

H1524 LK-500B H1525 LK-500BS

LMDV-3530

H1526 LK-600B H1527 LK-600BS

LMDV-4035

Polished Brass & Brushed Stainless 2-Piece Door Frame Kits

These kits are designed to attach directly to the front face of the appliance at the glass enclosure panel's top

and bottom edges.

(ref. Form # 750,098M)

2- Piece Door Frame Kits

Polished Brass Brushed Stainless

Models

Where Used

Cat. #

Model Cat. # Model

98L18 2DFK33PB 98L19 2DFK33BS

LMDVT-3328

LMDVR-3328

26M88 2DFK35PB 26M91 2DFK35BS LMDV-4035

26M89 2DFK40PB

26M92 2DFK40BS LMDV-4035

Polished Brass & Brushed Stainless Louvers Kits

These kits include a top 4-louver assembly and a bottom 4-louver assembly. They provide a touch of elegance.

These kits can be retroﬁtted to previously installed appliances.

(ref. Form # 750,166M)

Polished Brass & Brushed Stainless Hood Kits

Attractive hoods are available in two styles. These hoods are designed to be ﬁtted to the glass viewing sides

of the appliance. In addition to providing an aesthetically pleasing appearance to your appliance installation,

the hood reduces heat effects to decorative mantles and ﬁnish materials located above the ﬁreplace opening.

The hood kit replaces the standard hood that comes with these appliances and snaps into place. These kits

can be retroﬁtted to previously installed appliances.

(ref. Form #504,142M)

Eyebrow Hood Kits

Polished Brass Brushed Stainless Models

Where Used

Cat. #

Model Cat. # Model

98L10 EB33PB 98L11 EB33BS

LMDVT-3328

LMDVR-3328

96K67 EB35PB 88L49 EB35BS LMDV-4035

96K68 EB40PB 88L50 EB40BS LMDV-4035

* These hood kits replace the standard hood that comes with

these ﬁreplaces.

Door Frame Kits

A decorative door frame kit is available for use with these appliances. It is designed to attach directly to the front face

of the appliance at the four edges of the glass enclosure panel resulting in the appearance of a picture frame.

(ref. Form # 750,098M)

4 Piece Door Trim Kits

Polished Brass Brushed Stainless Models

Where Used

Cat. #

Model Cat. # Model

98L22 4DFK33PB 98L23 4DFK33BS

LMDVT-3328

LMDVR-3328

26M82 4DFK35PB 26M85 4DFK35BS LMDV-3530

26M83 4DFK40PB 26M86 4DFK40BS LMDV-4035

* Lennox Nameplate Logo, 12L15, is sold separately.

Touch-Up Paint Kit

Repair of minor scratches and discoloration of the

appliance charcoal painted surfaces may be accom

plished with the touch-up paint kit.

Touch-Up Paint Kits

(all models)

Cat. No. Model No. Description

90L74 TPK-C Touch-Up Paint (Charcoal)

(TPK-C ref. Form # 504,216M)

Ref. 750,109M Ref. 750,055M

Termination Guard Kits

(all models)

Cat. No. Model No. Description

H5820 4.5HTSK Termination Shroud

87L02 SV4.5HGS Termination Guard,

Deluxe

17M52 SV4.5HGS-1 Termination Guard,

Square

Square Termination

Guard

Deluxe Termination

Guard

Termination Guard Kits

The vent termination guards may be used to cover

the vent termination on the exterior of the home

to minimize exposure to the hot surface of the

termination.

Termination Shroud

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

H3541 CUGK35C 35” Charcoal

UPPER GRILLE KITS

CRESCENTS

H3543 CUGK35SP 35” Satin Pewter

H3549 CUGK40C 40” Charcoal

H3551 CUGK40SP

40” Satin Pewter

H3569 SLGK35C 35” Charcoal

LOWER GRILLE KITS

SUNRISE

H3571 SLGK35SP 35” Satin Pewter

H3577 SLGK40C 40” Charcoal

H3579 SLGK40SP 40” Satin Pewter

Cat. No.# Model Description Model Series

H3565 SUGK35C 35” Charcoal

UPPER GRILLE KITS

SUNRISE

H3567 SUGK35SP 35” Satin Pewter

H3573 SUGK40C 40” Charcoal

H3575 SUGK40SP 40” Satin Pewter

H3545 CLGK35C 35” Charcoal

LOWER GRILLE KITS

CRESCENTS

H3547 CLGK35SP 35” Satin Pewter

H3553 CLGK40C 40” Charcoal

H3555 CLGK40SP 40” Satin Pewter

Sunrise Style (upper grille shown)

Crescent Style (lower grille shown)

(ref. Form # 750,202M)

Note: Door & Trim Kits are for 1 side only. If set is desired, order 2 kits.

Decorative Grille Kits

These decorative grilles are offered in two attractive ﬁnishes and ﬁt on the

face of the appliance in place of the standard louvers.

Tall Style View Doors -

These decorative screen doors are offered in four

attractive ﬁnishes and ﬁt on the face of the appliance

over the glass doorframe to prevent direct contact

with the hot glass surface. The screens prevent direct

contact with the hot glass surface. These doors replace

the bottom louver assembly and cover the control

compartment which elongates the appearance of the

height of the ﬁreplace face.

Style View Tall Arch Pane Screen Door Kits

Cat#

Model Description

H3525 TAPD35C 35”, Charcoal

H3527 TAPD35SP 35”, Satin Pewter

H3529 TAPD40C 40”, Charcoal

H3531 TAPD40SP 40”, Satin Pewter

ACCESSORY COMPONENTS

LIGHTING INSTRUCTIONS – HONEYWELL AND SIT MILLIVOLT GAS VALVE

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which must be lighted with a piezo

igniter. When lighting the pilot, follow these instructions

exactly.

B. BEFORE OPERATING smell all around the appliance area for

gas. Be sure to smell next to the ﬂoor because some gas is

heavier than air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Extinguish any open ﬂame.

• Open windows.

• Do not light any appliance.

• Do not touch any electrical switches.

TO TURN OFF GAS TO APPLIANCE

1. Turn remote wall switch “OFF.” The pilot will remain lit for

normal service.

2. For complete shutdown, turn remote wall switch to “OFF.”

3. Access the lower control compartment.

4. Depress gas control knob slightly and turn clockwise

to “OFF.” Do not force.

5. Close lower control compartment.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this Page.

2. Access the lower control compartment.

3. Turn remote wall switch to “OFF.”

4. Verify main line shut-off valve is open.

5. Push in gas control knob slightly and turn clockwise

to “OFF.”

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone.

• If your gas supplier cannot be reached, call the ﬁre depart

ment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand,

do not try to repair it, call a qualiﬁed service technician. Force

or attempted repair may result in a ﬁre or an explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualiﬁed service technician to inspect the

appliance and to replace any part of the control system and

any gas control which has been under water.

Note: Knob cannot be turned from “PILOT” to “OFF”

unless the knob is pushed in slightly. Do not force.

HONEYWELL

MILLIVOLT

GAS VALVE

SIT

MILLIVOLT

GAS VALVE

SIT

MILLIVOLT PILOT

HONEYWELL

MILLIVOLT PILOT

OUT

IGNITER

6. Wait ﬁve (5) minutes to clear out any gas. If you then smell gas,

STOP! Follow “B” in the safety information above on this Page. If

you do not smell gas, go to the next step.

7. Push in gas control knob slightly and turn counterclockwise

to “PILOT.”

8. Push in control knob all the way and hold in.

Immediately light the pilot by triggering the

spark igniter (pushing the button) until pilot

lights. Continue to hold the control knob in

for about 1 minutes after the pilot is lit.

Release knob and it will pop back up. Pilot

should remain lit. If it goes out, repeat steps

5 through 8.

• If knob does not pop up when released,

stop and immediately call your service

technician or gas supplier.

• If pilot will not stay lit after several tries,

turn the control knob to “OFF” and call

your service technician or gas supplier.

9. Turn gas control knob counterclockwise

to “ON.”

10. Close lower control compartment.

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT HONEYWELL ET SIT

INSTRUCTIONS D'ALLUMAGE

8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé.

Allumez immédiatement la veilleuse en déclenchant l’allume-gaz à

étincelle (en poussant le bouton) jusqu’à ce que la veilleuse

s’enflamme. Continuez de tenir le bouton de réglage enfoncé

pendant environ 90 secondes après l’allumage de la veilleuse.

Relâchez le bouton et il sortira

subitement. La veilleuse devrait rester

allumée. Si elle s’éteint, répétez les

étapes 5 à 8 inclusivement.

• Si le bouton ne sort pas

automatiquement après avoir été

relâché, arrêtez immédiatement et

téléphonez à votre technicien de

service ou à votre fournisseur de gaz.

• Si la veilleuse refuse de rester allumée

après plusieurs tentatives, tournez le

bouton de réglage jusqu’à sa position

d’arrêt “OFF” et téléphonez à votre

technicien de service ou à votre

fournisseur de gaz.

9. Tournez le bouton de réglage du gaz en

sens inverse des aiguilles d’une

montre jusqu’à sa position

de marche “ON”.

10. Fermez le compartiment de contrôle du bas.

11. Au besoin, rebrancher l’appareil au courant électrique et remettre

l’interrupteur du brûleur principal à la position “ON” ou régler le

thermostat à la température désirée.

12. Si l’appareil ne fonctionne pas, suivre les instructions intitulées

“Pour fermer le gaz qui alimente l’appareil” et appeler un

technicien ou le fournisseur de gaz.

AVERTISSEMENT : SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU UNE

EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.

POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE

A. Cet appareil est muni d’une veilleuse qui doit être allumée avec un

allumeur piézo-électrique. Lorsque vous allumez la veilleuse, suivre

exactement ces instructions.

B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez aucune

odeur de gaz autour de l’apareil ainsi que près du sol; certains gaz, étant

plus lourds que l’air, descendent au niveau du sol.

VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE ODEUR

DE GAZ:

• Éteignez toute flamme visible.

• Ouvrez les fenêtres.

• N’allumez aucun appareil.

• Ne touchez à aucun commutateur électrique.

• Ne vous servez d’aucun téléphone dans votre édifice.

• Appelez immédiatement votre compagnie de gaz en utilisant le téléphone

du voisin.

• S’il vous est impossible de contacter votre compagnie de gaz, appelez

le service des incendies.

C. N’utilisez que votre main pour manipuler le bouton de réglage du gaz.

N’utilisez jamais d’outils. Si le bouton refuse de tourner ou de bouger,

n’essayez pas de le réparer. Communiquez immédiatement avec un

technicien de service qualifié. Toute tentative pour le forcer ou le

réparer, risquerait de provoquer un incendie ou une explosion.

D. Ne vous servez pas de cet appareil si l’un de ses éléments a été

immergé dans l’eau. Appelez immédiatement un technicien compétent

pour faire inspecter l’appareil et remplacer toute pièce du système de

réglage ou commande du gaz qui a été sous l’eau.

1. ARRÊTEZ! Lisez les consignes de sécurité au verso de cette plaque.

2. Ouvrez le compartiment de contrôle du bas.

3. Tournez l’interrupteur mural à la position d’arrêt “OFF”.

4. Assurez-vous que la soupape d’arrêt de la canalisation principale est

ouverte.

5. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans

le sens des aiguilles d’une montre jusqu’à la position

d’arrêt “OFF”.

Remarque: Il est impossible de tourner le bouton de “PILOT” à “OFF” à

moins qu’il ne soit légèrement enfoncé. Ne le forcez pas.

6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous décelez

une odeur de gaz, ARRÊTEZ ! Retournez au point “B” des consignes

de sécurité au verso de cette plaque. Si vous ne remarquez aucune

odeur de gaz, passez à l’étape suivante.

7. Enfoncez légèrement le bouton de réglage du gaz et tournez-le en

sens inverse des aiguilles d’une montre jusqu’à la position de

veilleuse “PILOT”.

1. Tournez l’interrupteur mural à la position d’arrêt “OFF”. La veilleuse

restera allumée jusqu’au retour du service normal.

2. Pour une fermeture complète, tournez l’interrupteur mural à la

position d’arrêt “OFF”.

3. Ouvrez le compartiment de contrôle du bas.

POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL

4. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans

le sens des aiguilles d’une montre jusqu’à la position

d’arrêt “OFF”. Ne forcez pas le bouton.

5. Fermez le compartiment de contrôle du bas.

VANNE GAZ

MILLIVOLT

HONEYWELL

VANNE GAZ

MILLIVOLT SIT

HONEYWELL

MILLIVOLT PILOT

SIT

MILLIVOLT PILOT

PIEZO-ELECTRIQUE

TPT

OUT

PIEZO-ELECTRIQUE

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A. When lighting the appliance, follow these instructions

exactly.

B. BEFORE OPERATING smell all around the appliance area

for gas. Be sure to smell next to the ﬂoor because some

gas is heavier than air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Extinguish any open ﬂame.

• Open windows.

• Do not light any appliance.

• Do not touch any electrical switches.

• Do not use any phone in your building.

FOR YOUR SAFETY READ BEFORE LIGHTING

• Immediately call your gas supplier from a neighbor’s

phone.

• If your gas supplier cannot be reached, call the ﬁre

department.

C. Use only your hand to turn the gas control lever. Never

use tools. If the lever will not turn by hand, do not try

to repair it, call a qualiﬁed service technician. Force or

attempted repair may result in a ﬁre or an explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualiﬁed service technician

to inspect the appliance and to replace any part of the

control system and any gas control which has been under

water.

LIGHTING INSTRUCTIONS — ELECTRONIC

1. For complete shut-down, turn remote wall switch to

“OFF.”

2. Open lower control compartment door.

3. Turn the OFF/ON switch to “OFF”. Do not force.

4. Close the main line shut-off valve.

5. Close lower control compartment door.

TO TURN OFF GAS TO APPLIANCE

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this Page.

2. Turn remote wall switch to “OFF.”

3. Open lower control compartment door.

4. Verify main line shut-off valve is open.

5. Turn the OFF/ON switch to “OFF”. Do not force.

6. Wait ﬁve (5) minutes to clear out any gas. If you then

smell gas, STOP! Follow “B” in the safety information

above on this Page. If you do not smell gas, go to the

next step.

7. Turn the OFF/ON switch to “ON”. Do not force.

8. Turn “ON” all electrical power to appliance (remote wall

or appliance switch).

9. Close lower control compartment door.

TO SHUT OFF

1. Turn off all electrical power to the appliance (remote wall

switch).

Honeywell Electronic Gas Control Valve

ON/OFF Switch

Front View

La page charge ...

Lennox LMDTV-3328CNM Manuel utilisateur

Marque: Lennox

Modèle: LMDTV-3328CNM

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Lennox LMDTV-3328CNM User manual

Lennox LMDTV-3328CNM Manuel utilisateur

Lennox LMDTV-3328CNM Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents