Samsung ME16K3000AS Le manuel du propriétaire

Marque: Samsung

Modèle: ME16K3000AS

Catégorie: Fours

Taper: Le manuel du propriétaire

Ce manuel convient également à

INSTALLATION INSTRUCTIONS

OVER THE RANGE MICROWAVE OVEN

BEFORE YOU BEGIN (Read these instructions completely and carefully.)

IMPORTANT

Save these instructions for local inspector’s use.

IMPORTANT

Observe all governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical and electrical skills.

• Properinstallationistheresponsibilityoftheinstaller.

• ProductfailureduetoimproperinstallationisnotcoveredundertheWarranty.

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

DE68-03587B-EN.indd 1 2009-07-10 �� 4:40:25

Placement Of The Mounting Plate ..... 8

RemovingtheMountingPlate . . . . . . . . .8

FindingtheWallStuds ...............8

DeterminingWallPlateLocation . . . . . . .9

AligningtheWallPlate ...............10

Installation Types . . . . . . . . . . . . . . . . . . 11

. Outside Top Exhaust . . . . . . . . . . . . . . . .12

AttachMountingPlatetotheWall . . . . . .12

PreparationofTopCabinet ...........12

InstallationProcedureForExhaustAdaptor

AndProperDamperOperationCheck ...13

Mount the Microwave Oven . . . . . . . . . . .13

Adjust the Exhaust Adaptor ...........14

Connecting Ductwork ................14

B. Recirculating . . . . . . . . . . . . . . . . . . . . . .15

AttachMountingPlatetoWall . . . . . . . . .15

PreparationofTopCabinet ...........15

Adapting Microwave Blower For

Recirculation . . . . . . . . . . . . . . . . . . . . . .16

Mount the Microwave Oven . . . . . . . . . . .17

Install the Charcoal Filter .............18

C. Outside Back Exhaust . . . . . . . . . . . . . . .19

PreparingRearWallfor

Outside Back Exhaust . . . . . . . . . . . . . . .19

AttachMountingPlatetoWall . . . . . . . . .20

PreparationofTopCabinet ...........20

Adapting Microwave Blower For Outside

Back Exhaust ......................20

Mount the Microwave Oven . . . . . . . . . . .22

Before You Use Your Microwave ....... 23

Step-by-step installation guide

Contents

Important Safety Instructions . . . . . . . . 3

Electrical Requirements ............. 3

Hood Exhaust . . . . . . . . . . . . . . . . . . . . . 4

Damage - Shipment/installation ....... 6

Parts Included . . . . . . . . . . . . . . . . . . . . . 6

Tools You Will Need ................. 7

Mounting Space . . . . . . . . . . . . . . . . . . . 7

General information

DE68-03587B-EN.indd 2 2009-07-10 �� 4:40:25

General information

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

Theinstallermustperformagroundcontinuity

check on the power outlet box before beginning the

installationtoinsurethattheoutletboxisproperly

grounded.Ifnotproperlygrounded,oriftheoutlet

box does not meet electrical requirements noted

(underELECTRICALREQUIREMENTS),aqualied

electricianshouldbeemployedtocorrectany

deciencies.

)NSUREPROPER

GROUNDEXISTS

BEFOREUSE

CAUTION: For personal

safety, remove

house fuse or open

circuit breaker before

beginning installation

to avoid severe or fatal

shock injury.

CAUTION: For personal safety, the mounting

surface must be capable of supporting the cabinet

load, in addition to the added weight of this 63–85

pound product, plus additional oven loads of up to

50 pounds or a total weight of 113–135 pounds.

CAUTION: For personal safety, this product cannot

be installed in cabinet arrangements such as an

island or a peninsula. It must be mounted to BOTH

a top cabinet AND a wall.

NOTE: For easier installation and personal safety,

it is recommended that two people install this

product.

IMPORTANT – PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

)NSUREPROPER

GROUNDEXISTS

BEFOREUSE

The power cord of this

appliance is equipped

with a three-prong

(grounding) plug which

mates with a standard

three-prong (grounding)

wall receptacle to

minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit

checked by a qualiﬁed electrician to make sure the

receptacle is properly grounded.

Where a standard two-prong wall receptacle

is encountered, it is very important to have it

replaced with a properly grounded three-prong

wall receptacle, installed by a qualiﬁed electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH AN

EXTENSION CORD.

ELECTRICAL REQUIREMENTS

Productratingis120voltsAC,60Hertz,13.5amps

and 1.5 kilowatts. This product must be connected to

asupplycircuitofthepropervoltageandfrequency.

Wiresizemustconformtotherequirementsofthe

National Electrical Code or the prevailing local code

forthiskilowattrating.Thepowersupplycordandplug

should be brought to a separate 20 ampere branch

circuit single grounded outlet. The outlet box should

be located in the cabinet above the microwave oven.

Theoutletboxandsupplycircuitshouldbeinstalled

byaqualiedelectricianandconformtotheNational

Electrical Code or the prevailing local code.

DE68-03587B-EN.indd 3 2009-07-10 �� 4:40:26

General information

HOOD EXHAUST

NOTE: Read these next two pages only if you plan to vent your exhaust to the outside.

If you plan to recirculate the air back into the room, proceed to page 11.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

DUCT PIECES

EQUIVALENT

LENGTH

NUMBER

USED

EQUIVALENT

LENGTH

Roof Cap 24 ft. x (1) = 24 ft.

12 Ft. Straight Duct

(6”Round)

12 ft. x (1) = 12 ft.

Rectangular-to-Round

Transition Adaptor*

5 ft. x (1) = 5 ft.

Equivalent lengths of duct pieces are based on

actual tests and reﬂect requirements for good venting

performancewithanyventhood.

Total

Length

= 41 ft.

* IMPORTANT:Ifarectangular-to-roundtransitionadaptorisused,thebottomcornersofthedamper

willhavetobecuttot,usingthetinsnips,inordertoallowfreemovementofthedamper.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

DUCT PIECES

EQUIVALENT

LENGTH

NUMBER

USED

EQUIVALENT

LENGTH

WallCap 40 ft. x (1) = 40 ft.

3 Ft. Straight Duct

(3¼” x 10”

Rectangular)

3 ft. x (1) = 3 ft.

90° Elbow 10 ft. x (2) = 20 ft.

Equivalent lengths of duct pieces are based on

actual tests and reﬂect requirements for good venting

performancewithanyventhood.

Total

Length

= 63 ft.

NOTE:Forbackexhaust,careshouldbetakentoalignexhaustwithspacebetweenstuds,orwallshouldbeprepared

atthetimeitisconstructedbyleavingenoughspacebetweenthewallstudstoaccommodateexhaust.

DE68-03587B-EN.indd 4 2009-07-10 �� 4:40:26

General information

NOTE:Ifyouneedtoinstallducts,notethatthetotalduct

length of 3¼” x 10” rectangular or 6” diameter round duct

should not exceed 140 equivalent feet.

OutsideventilationrequiresaHOODEXHAUSTDUCT.

Readthefollowingcarefully.

NOTE: It is important that venting be installed using the

most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The hood exhaust has been designed to mate with a

standard 3¼” x 10” rectangular duct.

Ifaroundductisrequired,arectangular-to-round

transition adaptor must be used. Do not use less than a

6” diameter duct.

Maximum duct length:

Forsatisfactoryairmovement,thetotalductlengthof3¼”

x 10” rectangular or 6” diameter round duct should not

exceed 140 equivalent feet.

Elbows, transitions, wall and roof caps, etc.,

present additional resistance to airﬂow and are equivalent

to a section of straight duct which is longer than their

actualphysicalsize.Whencalculatingthetotalduct

length,addtheequivalentlengthsofalltransitionsand

adaptors plus the length of all straight duct sections. The

chartbelowshowsyouhowtocalculatetotalequivalent

ductwork length using the approximate feet of equivalent

lengthofsometypicalducts.

DUCT PIECES

EQUIVALENT

LENGTH

x NUMBER USED =

EQUIVALENT

LENGTH

Rectangular-to-Round

Transition Adaptor*

5 ft. x () = ft.

WallCap 40 ft. x () = ft.

90° Elbow 10 ft. x () = ft.

45° Elbow 5 ft. x () = ft.

90° Elbow 25 ft. x () = ft.

45° Elbow 5 ft. x () = ft.

Roof Cap 24 ft. x () = ft.

Straight Duct 6” Round or

3¼” x 10” Rectangular

1 ft. x () = ft.

Total Ductwork = ft.

* IMPORTANT: If a rectangular-to-round transition

adaptorisused,thebottomcornersofthedamper

willhavetobecuttot,usingthetinsnips,in

order to allow free movement of the damper.

Equivalent lengths of duct pieces

are based on actual tests and reﬂect

requirements for good venting performance

withanyventhood.

DE68-03587B-EN.indd 5 2009-07-10 �� 4:40:27

General information

• If the unit is damaged in shipment,returntheunittothestoreinwhichitwasboughtforrepairorreplacement.

• If the unit is damaged by the customer,repairorreplacementistheresponsibilityofthecustomer.

• If the unit is damaged by the installer(ifotherthanthecustomer),repairorreplacementmustbemadeby

arrangement between customer and installer.

DAMAGE - SHIPMENT/INSTALLATION

HARDWARE PACKET

PART QUANTITY

Template

INSTALLATION

INSTRUCTIONS

WoodScrews

(¼”x2”)

Template

INSTALLATION

INSTRUCTIONS

Toggle Bolts

(andwingnuts)

(3/16”x3”)

Template

INSTALLATION

INSTRUCTIONS

Self-aligning

Machine Screws

(¼”-28x3¼”)

Template

INSTALLATION

INSTRUCTIONS

NylonGrommet

(formetalcabinets)

Youwillndtheinstallationhardwarecontainedina

packetwiththeunit.Checktomakesureyouhaveall

these parts.

NOTE: Some extra parts are included.

ADDITIONAL PARTS

PART QUANTITY

4/0#!").%44%-0,!4%

2%!27!,,4%-0,!4%

Top Cabinet

Template

4/0#!").%44%-0,!4%

2%!27!,,4%-0,!4%

RearWall

Template

INSTALLATION

INSTRUCTIONS

Installation

Instructions

Template

INSTALLATION

INSTRUCTIONS

Separately

PackedGrease

Filter

Template

INSTALLATION

INSTRUCTIONS

Exhaust adaptor 1

PARTS INCLUDED

DE68-03587B-EN.indd 6 2009-07-10 �� 4:40:27

General information

# 1 and #2

Phillipsscrewdriver

Pencil Ruler or tape measure and

straight edge

Carpentersquare(optional)

Tin snips (for cutting

damper,ifrequired)

Scissors(tocuttemplate,if

necessary)

Electric drill with

/16”,½”and

/8” drill bits

Filler blocks or scrap wood

pieces,ifneededfortop

cabinet spacing (used on

recessed bottom cabinet

installationsonly)

Gloves Saw

(saber,holeorkeyhole)

StudnderorHammer

(optional)

Safetygoggles

Level Duct and masking tape

TOOLS YOU WILL NEED

16½”

30”

2”

30”min

Bottom edge of

cabinet needs

to be 30” or

more from

the cooking

surface

Backsplash

66” or More

from the Floor

to the Top of

the Microwave

NOTES:

• Thespacebetweenthecabinetsmustbe30”wide

and free of obstructions.

• Ifthespacebetweenthecabinetsisgreaterthan

30”,aFillerPanelKitmaybeusedtollinthegap

between the microwave oven and the cabinets.

Your Owner’s Manual contains the kit number for

yourmodel.

• Thismicrowaveovenisforinstallationoverranges

up to 36” wide.

• Ifyouaregoingtoventyourmicrowaveoven

totheoutside,seeHoodExhaustSectionfor

exhaust duct preparation.

• When installing the microwave oven beneath

smooth, ﬂat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearance.

MOUNTING SPACE

DE68-03587B-EN.indd 7 2009-07-10 �� 4:40:29

Step-by-step installation guide

1. PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE

MICROWAVE OVEN FROM

THE CARTON/REMOVING

THE MOUNTING PLATE

1. Removetheinstallationinstructions,Exhaust

adaptor,lters,glasstrayandthesmallhardware

bag.DonotremovetheStyrofoamprotectingthe

front of the oven.

2. Foldbackall4cartonapsfullyagainstcarton

sides.Thencarefullyrolltheovenandcartonover

onto the top side. The oven should be resting in the

Styrofoam.

3TYROFOAM

#ARTON

3. Pullthecartonupandofftheoven.

4. Removeandproperlydiscardplasticbags.

Screws

Mounting Plate

5. Remove the 2 screws from the mounting plate. This

plate will be used as the rear wall template and for

mounting.

NOTE: You will have to reuse two screws in original

location of outcase after removing mounting plate.

B. FINDING THE WALL STUDS

7ALL3TUDS

#ENTER

1. Findthestuds,usingoneofthefollowingmethods:

A.Studnder-amagneticdevicewhichlocates

nails.

B.Useahammertotaplightlyacrossthemounting

surfacetondasolidsound.Thiswillindicatea

stud location.

2. Afterlocatingthestud(s),ndthecenterbyprobing

thewallwithasmallnailtondtheedgesofthe

stud.Thenplaceamarkhalfwaybetweenthe

edges.Thecenterofanyadjacentstudsshouldbe

16” or 24” from this mark.

3. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO AT

LEAST ONE WALL STUD.

DE68-03587B-EN.indd 8 2009-07-10 �� 4:40:30

Step-by-step installation guide

C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET

16-1/2"

Plate position – beneath flat bottom cabinet

Draw a vertical line on

the wall at the center of

the 30

q wide space.

Tape the Rear Wall

Template onto the wall

matching the centerline

and touching the

bottom of the cabinet.

Plate position – beneath framed recessed

cabinet bottom

30q to Cooktop

Draw a vertical line on the wall at the center of the

q space.

Tape the Rear Wall Template onto the wall

matching the centerline and touching the bottom

cabinet frame.

Plate position – beneath recessed bottom

cabinet with front overhang

Draw a line on the

back wall equal to the

depth of the front

overhang.

30" to Cooktop

Yourcabinetsmayhavedecorativetrimthatinterferes

with the microwave installation. Remove the decorative

trimtoinstallthemicrowaveproperlyandtomakeitlevel.

THE MICROWAVE MUST BE LEVEL.

Usealeveltomakesurethecabinetbottomislevel.

Ifthecabinetshaveafrontoverhangonly,withnoback

orsideframe,installthemountingplatedownthesame

distance as the front overhang depth. This will keep the

microwave level.

. Measure the inside depth of the front overhang.

. Drawa horizontal line on theback wall anequal

distance below the cabinet bottom as the inside depth

of the front overhang.

. Forthistypeofinstallationwithfrontoverhangonly,

alignthemountingtabswiththishorizontalline,not

touching the cabinet bottom as described in Step D.

DE68-03587B-EN.indd 9 2009-07-10 �� 4:40:32

Step-by-step installation guide

D. ALIGNING THE WALL PLATE

CAUTION: Wear gloves to avoid cutting

fingers on sharp edges.

Area E

Hole B

Hole A

Centerline

notches

Draw a Vertical Line

on Wall from Center

of Top Cabinet

Draw a Horizontal line on wall from

bottom of “Rear Wall Template”.

Horizontal Line

CAUTION:Wearglovestoavoidcuttingngersonsharp

edges.

1. Draw a Vertical line on the wall at the center of the 30"

wide space.

2. DrawaHorizontallineonthewallatthebottomof

“RearWallTemplate”.

3. Drill5/8"holesfortoggleboltson3locations(HoleA,

HoleB,HoleC)butifthelocationofholeissameas

thatofstud,drilla3/16"holeforwoodscrew.Inother

words,toggleboltcannotbeusedtothelocationof

stud.

NOTE: DO NOT MOUNT THE PLATE AT THIS

TIME.

NOTE:HolesA,BandCareinsideareaE.IfnoneofA,

BandCisinastud,ndastudsomewhereinareaEand

draw a forth circle to line up with the stud. It is important

to use at least one wood screw mounted ﬁrmly in a

stud to support the weight of the microwave. Set the

mounting plate aside.

DE68-03587B-EN.indd 10 2009-07-10 �� 4:40:33

Step-by-step installation guide

2. INSTALLATION TYPES (Choose A, B or C)

This microwave oven is designed for adaptation to the

followingthreetypesofventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Recirculating (Non-Vented Ductless)

C. Outside Back Exhaust (Horizontal Duct)

NOTE: This microwave is shipped assembled for Outside

TopExhaust(exceptfornon-ventedmodels).Select

thetypeofventilationrequiredforyourinstallationand

proceed to that section.

A. OUTSIDE TOP EXHAUST

(VERTICAL DUCT)

B. RECIRCULATING

(NON-VENTED DUCTLESS)

!DAPTORIN0LACE

FOR/UTSIDE

4OP%XHAUST

See page 12 See page 15

C. OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

See page 19

DE68-03587B-EN.indd 11 2009-07-10 �� 4:40:33

Step-by-step installation guide

A. OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. AttachMountingPlatetoWall

A2. PrepareTopCabinet

A3. Mount the Microwave Oven

A4. Adjust the Exhaust Adaptor

A5. Connecting Ductwork

A1. ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate to a

wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the

holesdesignatedtogointodrywallandreattachthe

toggle wings to ¾” onto each bolt.

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More

Than Wall Thickness

Mounting

Plate

3. Placethemountingplateagainstthewallandinsert

the toggle wings into the holes in the wall to mount

the plate.

NOTE:Beforetighteningtoggleboltsandwoodscrew,

make sure the tabs on the mounting plate touch the

bottom of the cabinet when pushed ﬂush against the

wallandthattheplateisproperlycenteredunderthe

cabinet.

CAUTION:Becarefultoavoidpinchingngers

between the back of the mounting plate and the wall.

4. Tightenallbolts.Pulltheplateawayfromthewallto

help tighten the bolts.

A2. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

Youneedtodrillholesforthetopsupportscrews,a

holelargeenoughforthepowercordtotthrough,and

a cutout large enough for the exhaust adaptor.

• ReadtheinstructionsontheTOPCABINET

TEMPLATE.

• Tapeitunderneaththetopcabinet.

• Drilltheholes,followingtheinstructionsontheTOP

CABINETTEMPLATE.

CAUTION:Wearsafetygoggleswhendrillingholesin

the cabinet bottom.

DE68-03587B-EN.indd 12 2009-07-10 �� 4:40:34

Step-by-step installation guide

A4. MOUNT THE MICROWAVE OVEN

FOREASIERINSTALLATIONANDPERSONAL

SAFETY,WERECOMMENDTHATTWOPEOPLE

INSTALLTHISMICROWAVEOVEN.

IMPORTANT: Do not grip or use handle during

installation.

NOTE:Ifyourcabinetismetal,usethenylongrommet

around the power cord hole to prevent cutting of the

cord.

NOTE:Werecommendusingllerblocksifthecabinet

front hangs below the cabinet bottom shelf.

IMPORTANT: If ﬁller blocks are not used, case

damage may occur from over tightening screws.

NOTE:Whenmountingthemicrowaveoven,thread

power cord through hole in bottom of top cabinet. Keep

it tight throughout Steps 1-3. Do not pinch cord or lift

ovenbypullingcord.

1. Liftmicrowave,

tiltitforward,and

hook slots at back

bottom edge onto

four lower tabs of

mounting plate.

2. Rotate front of oven

up against cabinet

bottom

3. Insert a self-aligning screw through top center

cabinethole.Temporarilysecuretheovenbyturning

the screw at least two full turns after the threads

haveengaged.(Itwillbecompletelytightenedlater.)

Be sure to keep power cord tight. Be careful not

to pinch the cord, especially when mounting

ﬂush to bottom of cabinet.

A3. INSTALLATION PROCEDURE

FOR EXHAUST ADAPTOR AND

PROPER DAMPER OPERATION

CHECK

1. Slide exhaust adaptor following the instructions

show in diagram.

2. Make sure tape securing damper is removed and

damperpivotseasolybeforemountingmicrowave.

CAUTION: You will need to make adjustments to

assureproperalignmentwithyourhouseexhaustduct

after the microwave is installed.

Exhaust Adaptor and Damper is

shippedassembledtotheller-upper.

DE68-03587B-EN.indd 13 2009-07-10 �� 4:40:36

Step-by-step installation guide

A5. ADJUST THE EXHAUST

ADAPTOR

Open the top cabinet and adjust the exhaust adaptor to

connect to the house duct.

"ACKOF

-ICROWAVE

"LOWER0LATE

$AMPER

&OR&RONTTO"ACK

OR3IDETO3IDE!DJUSTMENT

3LIDETHE%XHAUST

!DAPTORAS.EEDED

A6. CONNECTING DUCTWORK

(OUSE$UCT

1. Extend the house duct down to connect to the

exhaust adaptor.

2. Seal exhaust duct joints using duct tape.

#ABINET&RONT

&ILLER"LOCK

-ICROWAVE/VEN4OP

3ELF!LIGNING3CREW

%QUIVALENTTO

$EPTHOF

#ABINET2ECESS

#ABINET"OTTOM3HELF

4. Attach the microwave oven to the top cabinet.

5. Insert 2 self-aligning screws through

outer top cabinet holes. Turn two full

turns on each screw.

6. Tighten center

screwcompletely.

7. Tighten the outer two screws to the top of the

microwaveoven.(Whiletighteningscrews,holdthe

microwave oven in place against the wall and the

topcabinet.)

8. Installgreaselter.SeetheOwner’sManualpacked

with the microwave.

DE68-03587B-EN.indd 14 2009-07-10 �� 4:40:37

Step-by-step installation guide

B2. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

aholelargeenoughforthepowercordtotthrough.

• ReadtheinstructionsontheTOPCABINET

TEMPLATE.

• Tapeitunderneaththetopcabinet.

• Drilltheholes,followingtheinstructionsontheTOP

CABINETTEMPLATE.

CAUTION:Wearsafetygoggleswhendrillingholesin

the cabinet bottom.

B. RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

B1. AttachMountingPlatetoWall

B2. PrepareTopCabinet

B3. Adjust Blower

B4. Mount Microwave Oven

B5. Install Charcoal Filter

B1. ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate to a

wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the

holesdesignatedtogointodrywallandreattachthe

toggle wings to ¾” onto each bolt.

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More

Than Wall Thickness

Mounting

Plate

3. Placethemountingplateagainstthewallandinsert

the toggle wings into the holes in the wall to mount

the plate.

NOTE:Beforetighteningtoggleboltsandwoodscrew,

make sure to coincide bottom line of the Mounting

platewithHorizontallineof“RearwallTemplate”and

thentheMountingplateisproperlycenteredunderthe

cabinet.

CAUTION:Becarefultoavoidpinchingngers

between the back of the mounting plate and the wall.

4. Tightenallbolts.Pulltheplateawayfromthewallto

help tighten the bolts.

DE68-03587B-EN.indd 15 2009-07-10 �� 4:40:37

Step-by-step installation guide

B3. ADAPTING MICROWAVE

BLOWER FOR RECIRCULATION

Back of

Microwave

1. Remove and save screw

that holds blower plate to

microwave.

2. Lift up the

blower plate.

NOTE: The exhaust adaptor with damper is not needed

forrecirculatingmodels.Youmaywanttosavethemfor

possible future use.

3. Carefullypullouttheblowerunit.Thewireswill

extendfarenoughtoallowyoutoadjusttheblower

unit.

CAUTION: Do not touch blade of blower forpreventing

crackandbreak.Holdoutercasewhentheblowerpull

out or back into.

4. Roll the blower unit 90° so that fan blade openings

are facing toward the front of the microwave.

BEFORE: Fan Blade

Openings Facing UP

AFTER: Fan Blade

Openings Facing Forward

5. Placetheblowerunitbackintotheopening.

CAUTION: Do not pull or stretch the blower unit wiring.

Make sure the wires are not pinched.

6. Secure blower unit to microwave with the screw.

blower mortor screw

DE68-03587B-EN.indd 16 2009-07-10 �� 4:40:38

Step-by-step installation guide

B4. MOUNT THE MICROWAVE

OVEN

FOREASIERINSTALLATIONANDPERSONAL

SAFETY,WERECOMMENDTHATTWOPEOPLE

INSTALLTHISMICROWAVEOVEN.

IMPORTANT: Do not grip or use handle during

installation.

NOTE:Ifyourcabinetismetal,usethenylongrommet

around the power cord hole to prevent cutting of the

cord.

NOTE:Werecommendusingllerblocksifthecabinet

front hangs below the cabinet bottom shelf.

IMPORTANT: If ﬁller blocks are not used, case

damage may occur from over tightening screws.

NOTE:Whenmountingthemicrowaveoven,thread

power cord through hole in bottom of top cabinet. Keep

it tight throughout Steps 1-3. Do not pinch cord or lift

ovenbypullingcord.

1. Liftmicrowave,

tiltitforward,and

hook slots at back

bottom edge onto

four lower tabs of

mounting plate.

2. Rotate front of oven

up against cabinet

bottom

3. Insert a self-aligning screw through top center

cabinethole.Temporarilysecuretheovenby

turning the screw at least two full turns after

thethreadshaveengaged.(Itwillbecompletely

tightenedlater.)Be sure to keep power cord

tight. Be careful not to pinch the cord,

especially when mounting ﬂush to bottom of

cabinet.

#ABINET&RONT

&ILLER"LOCK

-ICROWAVE/VEN4OP

3ELF!LIGNING3CREW

%QUIVALENTTO

$EPTHOF

#ABINET2ECESS

#ABINET"OTTOM3HELF

4. Attach the microwave oven to the top cabinet.

5. Insert 2 self-aligning screws through

outer top cabinet holes. Turn two full

turns on each screw.

6. Tighten center

screwcompletely.

7. Tighten the outer two screws to the top of the

microwaveoven.(Whiletighteningscrews,holdthe

microwave oven in place against the wall and the

topcabinet.)

8. Installgreaselter.SeetheOwner’sManual

packed with the microwave.

DE68-03587B-EN.indd 17 2009-07-10 �� 4:40:39

Step-by-step installation guide

B5. INSTALLING THE CHARCOAL

FILTER

. Removescrewsontopofgrilleusinga#1Phillips

screwdriver.

. Open the door.

. Remove the grille.

• Afterpushleft,Pullthestraightoff.

Charcoal

filter

. Installthecharocalfilter.Whenproperlyinstalled,

thewiremeshoftheltershouldbevisiblefromthe

front.

. Reinstall the grille and the screws.

. Close the door.

Insert mesh-side up

DE68-03587B-EN.indd 18 2009-07-10 �� 4:40:39

Step-by-step installation guide

C. OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

C1. PrepareRearWall

C2. AttachMountingPlatetoWall

C3. PrepareTopCabinet

C4. Adjust Blower

C5. Mount the Microwave Oven

C1. PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

You need to cut an opening in the rear wall for outside

exhaust.

• ReadtheinstructionsontheREARWALL

TEMPLATE.

• Tapeittotherearwall.

• Cuttheopening,followingtheinstructionsofthe

REARWALLTEMPLATE.

DE68-03587B-EN.indd 19 2009-07-10 �� 4:40:40

Step-by-step installation guide

C2. ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts. At least

one wood screw must be used to attach the plate to a

wall stud.

1. Remove the toggle wings from the bolts.

2. Insert the bolts into the mounting plate through the

holesdesignatedtogointodrywallandreattachthe

toggle wings to ¾” onto each bolt.

To use toggle bolts:

Wall

Toggle Wings

Toggle

Bolt

Bolt End

Spacing for Toggles More

Than Wall Thickness

Mounting

Plate

3. Placethemountingplateagainstthewallandinsert

the toggle wings into the holes in the wall to mount

the plate.

NOTE:Beforetighteningtoggleboltsandwoodscrew,

make sure the tabs on the mounting plate touch the

bottom of the cabinet when pushed ﬂush against the

wallandthattheplateisproperlycenteredunderthe

cabinet.

CAUTION:Becarefultoavoidpinchingngers

between the back of the mounting plate and the wall.

4. Tightenallbolts.Pulltheplateawayfromthewallto

help tighten the bolts.

C3. USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

Youneedtodrillholesforthetopsupportscrews,a

holelargeenoughforthepowercordtotthrough,and

a cutout large enough for the exhaust adaptor.

• ReadtheinstructionsontheTOPCABINET

TEMPLATE.

• Tapeitunderneaththetopcabinet.

• Drilltheholes,followingtheinstructionsontheTOP

CABINETTEMPLATE.

CAUTION:Wearsafetygoggleswhendrillingholesin

the cabinet bottom.

C4. ADAPTING MICROWAVE

BLOWER FOR OUTSIDE BACK

EXHAUST

1. Remove and save screws that hold the blower plate

and the blower motor to the microwave.

Back of

Microwave

Screw

Lift up the

blower plate.

Screw

DE68-03587B-EN.indd 20 2009-07-10 �� 4:40:41

La page charge ...

Samsung ME16K3000AS Le manuel du propriétaire

Marque: Samsung

Modèle: ME16K3000AS

Catégorie: Fours

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Samsung ME16K3000AS Owner's manual

Samsung ME16K3000AS Le manuel du propriétaire

Ce manuel convient également à

Samsung ME16K3000AS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents