Compex WLE1216VX WiFi 5 4×4 MU MIMO Dual Band Module Mode d'emploi

Marque
Compex
Modèle
WLE1216VX WiFi 5 4×4 MU MIMO Dual Band Module
Taper
Mode d'emploi
hardware guide - WLE1216VX
1/3
Copyright © Compex Systems. All rights reserved. COMPEX and the COMPEX logo, are registered trademarks of Compex Systems Pte. Ltd..
While every eort is made to ensure the information is accurate, Compex does not accept liability for any errors or mistakes that may arise.
All specications are subject to change without notice.
Compex Systems Pte Ltd | www.compex.com.sg | (+65) 6288 8220 | [email protected]
hardware guide - WLE1216VX
1/3
hardware guide - WLE3002HX
1/3
Power Requirements
DC Power 3.3V
Power Consumption 6.6W (Max)
MiniPCIe Slot Pin Assignment
Component Map
Top side Bottom side
1 PCIE0_WAKE_N 2 VDD_3V3
3 NC 4 GND
5 NC 6 NC
7 PCIE0_CLKREQ_N 8 NC
9 GND 10 NC
11 PCIE0_REFCLK_N 12 NC
13 PCIE0_REFCLK_P 14 NC
15 GND 16 NC
Mechanical key E
17 NC 18 GND
19 NC 20 NC
21 GND 22 PCIE0_PERST
23 PCIE0_RX0_N 24 VDD_3V3
25 PCIE0_RX0_P 26 GND
27 GND 28 NC
29 GND 30 NC
31 PCIE0_TX0_N 32 NC
33 PCIE0_TX0_P 34 GND
35 GND 36 NC
37 NC 38 NC
39 VDD_3V3 40 GND
41 VDD_3V3 42 NC
43 GND 44 NC
45 NC 46 NC
47 NC 48 NC
49 NC 50 GND
51 NC 52 VDD_3V3
MiniPCIe edge
connector
CH2
CH0
U.FL connectors
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This module has been tested and found to comply with part 15 requirements for Modular Approval.
FCC Caution:Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Antenna Placement Within the Host Platform
The module is tested for standalone mobile RF exposure use condition.
(1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
(2) The transmitter module may not be co-located with any other transmitter or antenna.
In the event that these conditions cannot be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be
used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC authorization.
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The following antennas have been certified for use with this module.
Only antennas of the same type with equal or lower gain may also be used with this module.
Other types of antennas and/or higher gain antennas may require the additional authorization for operation.
Antenna Specification list below:
End Product Labeling
When the module is installed in the host device, the FCC ID label must be visible through a window on the final
device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be
placed on the outside of the final device that contains the following text: "Contains FCC ID: TK4WLE3002HX". The
FCC ID can be used only when all FCC compliance requirements are met.
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous
transmission with other transmitter(s) class II permissive change re-evaluation or new certification.
Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15
Subpart B rule requirement applicable to the final host. The final host will still need to be reassessed for
compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
Important Note
In the event that these conditions can not be met (for example certain laptop configurations or co-
location with another transmitter), then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
Antenna Type and Gain
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install
or remove this RF module in the user's manual of the end product which integrates this module.
The host integrator must follow the integration instructions provided in this document and
ensure that the composite-system end product complies with the requirements by a technical
assessment or evaluation to the rules and to KDB Publication 996369 .
The host integrator installing this module into their product must ensure that the final composite product complies
with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation
and should refer to guidance in KDB 996369.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final
product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B
before it can be placed on the US market. This includes reassessing the transmitter module for compliance with
the Radio and EMF essential requirements of the FCC rules.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)This device may not cause interference,and
(2)This device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de
licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage adioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
RF Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between
the radiator and your body.
Déclaration d'exposition aux radiations:
Cet appareil est conforme aux limites d'exposition aux rayonnements définies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale de 20 centimètres
entre le radiateur et votre corps.
Caution:
(i)
the device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interferenceto co-channel mobile satellite systems.
(ii)
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands
5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band
5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
Attention:
(i)
les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés uniquement pour une utilisation
à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux;
(ii)pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis pour les dispositifs
utilisant les bandes de 5250 à 5350MHz et de 5470 à 5725MHz doit être conforme à la limite de la p.i.r.e;
(iii)
pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis (pour les dispositifs
utilisant la bande de 5725 à 5850MHz) doit être conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
IMPORTANT NOTE
In the event that these conditions cannot be met (for example certain laptop configurations or co-location
with another transmitter), then the Canada authorization is no longer considered valid and the IC cannot be
used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'
ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est
plus considéré comme valide et IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'
intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
Required end product labeling:
This transmitter module is authorized only for use in device where the antenna may be installed and operated
with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area
with the following: "Contains IC:7849A-WLE3002HX".
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l'antenne peut être
installée et utilisée à plus de 20 cm entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans
un endroit visible avec l'inscription suivante: "Contient des IC: 7849A-WLE3002HX ".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user's manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
The following text, or an equivalent notice, that shall be displayed in a conspicuous location, either in the user
manual or on the device, or both:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two
conditions:
1)This device may not cause interference.
2)This device must accept any interference, including interference that may cause undesired operation of
the device.
The following antennas have been certified for use with this module; antennas of the same type with equal or
lower gain may also be used with this module. The antenna must be installed such that 20 cm can be
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'
installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements
comme indiqué dans ce manuel.
l'énoncé qui suit, ou l'équivalent, à un endroit bien en vue dans le manuel d'utilisation ou sur l'appareil, ou
encore aux deux endroits :
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
1.L'appareil ne doit pas produire de brouillage;
2.L'appareil doit accepter toute interférence, y compris toute interférence pouvant entraîner un
fonctionnement indésirable du dispositif.
Antenna
maintained between the antenna and users.
This radio transmitter has been approved by Innovation, Science and Economic Development Canada to
operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly
prohibited for use with this device.
Antenna Specification list below:
Les antennes suivantes ont été certifiées pour une utilisation avec ce module; des antennes du même type à
gain égal ou inférieur peuvent également être utilisées avec ce module. L'antenne doit être installée de telle
Cet émetteur radio a été approuvé par Innovation, Sciences et Développement économique Canada
pour fonctionner avec les types d'antenne énumérés ci-dessous, avec le gain maximal autorisé indiqué.
Les types d'antenne non inclus dans cette liste qui ont un gain supérieur au gain maximum indiqué pour
tout type répertorié sont strictement interdits pour l'utilisation avec cet appareil.
sorte que 20 cm puissent être maintenus entre l'antenne et les utilisateurs.
ANTENNE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Compex WLE1216VX WiFi 5 4×4 MU MIMO Dual Band Module Mode d'emploi

Marque
Compex
Modèle
WLE1216VX WiFi 5 4×4 MU MIMO Dual Band Module
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents