Bosch HBL5751UCC/02 Guide d'installation

Built-In Oven

Installation Manual

Table of Contents

Safety Definitions ............... 1

Preparation .................... 3

Before You Begin ..................... 3

Tools and Parts Needed ................ 3

Parts Included ........................ 3

General Information .................... 3

Dimensions and Cabinet

Requirements .................. 4

Removing Packaging ............ 4

Preparing Oven ....................... 4

Installation ..................... 5

Determine the Installation Type ........... 5

Pre-Assembly of Combination Ovens Prior to

Installation ........................... 5

Combination Oven Installation ............ 5

Electrical Installation ................... 8

Installing the Oven Unit into the Wall

Cabinet ............................. 9

For Best Installation .................... 9

Correct Inside Oven Lift Point ............ 9

Installing the Oven .................... 11

Bottom Hinge Doors Only - Remove Prior to

Install .............................. 11

Installing the Oven into the

Cabinet (all ovens) .................... 12

Ovens with Bottom Hinge Doors Only ..... 13

Ovens with Side Hinge Doors Only ....... 13

Before Calling Service ................. 16

Cabinet Dimension Requirements. 18

Dimensions for 27" Single Oven Units .. 18

Single Oven 27" Traditional Installation,

Cabinet and Undercounter .............. 18

Single Oven 27" Flush Mount Installation .. 18

Dimensions for 27" Double Oven Units.. 18

Double Oven 27" Traditional Installation ... 18

Double Oven 27" Flush Mount Installation .. 19

Dimensions for 30" Single Oven Units .. 19

Single Oven 30" Traditional Installation,

Cabinet and Undercounter .............. 19

Single Oven 30" Flush Mount Installations 19

Dimensions for 30" Double Oven Units.. 20

Double Oven 30" Traditional Installation ... 20

Double Oven 30" Flush Mount Installion ... 20

Dimensions for 30" Combination Oven

and Microwave or Steam Oven Units .... 21

Combination Oven and Microwave or Steam

Oven 30" Traditional Installation ......... 21

This Bosch Appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-944-2904

www.bosch-home.com/us

We look forward to hearing from you!

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Safety Definitions

WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

• UL 858, Household Electric Ranges

• UL 923, Microwave Cooking Appliances

• UL 507, The Standard for the Safety of Electric Fans

• CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

NOTICE: Ths indicates that damage to the appliance or

property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

Electric Safety

Before you plug in an electrical cord, be sure all controls

are in the OFF position.

WARNING:

If the information in this manual is not followed exactly, fire

or shock may result causing property damage or personal

injury.

WARNING:

Do not repair or replace any part of the appliance unless

specifically recommended in the manuals. Improper

installation, service or maintenance can cause injury or

property damage. Refer to this manual for guidance. All

servicing should be done by a qualified technician.

Appliance Handling Safety

Do not lift appliance by door handle. Remove the door for

easier handling and installation. See instructions in Use

and Care Manual.

Unit is heavy and requires at least two people or proper

equipment to move.

Hidden surfaces may have sharp edges. Use caution when

reaching behind or under appliance.

Unpacking the Oven

Unpack the oven, remove all tape and packaging material

and examine the oven for any damage such as dents,

broken door latches or cracks in the door. Notify dealer

immediately if oven is damaged. Do not install if oven is

damaged.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Installer - show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Important - Save these instructions for the local electrical

inspector's use.

Before installing, turn power OFF at the service panel. Lock

service panel to prevent power from being turned ON

accidentally.

Refer to data plate for more information. See "Data Plate"

under "Service" for data plate location.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

Related Equipment Safety

Remove all tape and packaging before using the appliance.

Destroy the packaging after unpacking the appliance.

Never allow children to play with packaging material.

Never modify or alter the construction of the appliance. For

example, do not remove leveling legs, panels, wire covers

or anti-tip brackets/screws.

9000989321 Rev A English 1

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Transport

To avoid damage to the oven vent, use the transport

method shown in the picture below.

Support the bottom of the oven from side to side when

moving it into the installation location. Leave the unit

attached to the shipping pallet until it is in front of the

cabinet opening, ready to lift into place.

English 2 9000989321 Rev A

Preparation

Before You Begin

Tools and Parts Needed

• Phillips head screwdriver

• Star-head screwdriver (T20)

• Measuring tape

• Drill with bit (1/8")

• Gloves

Parts Included

• Phillips head screws (6)

General Information

Power Requirements

The outlet must be properly grounded in accordance with

all applicable codes.

For Best Installation

The oven can be difficult for two people to handle during

installation. It is recommended to have three or more

people available to assist with lifting the unit into place.

Removal of the bottom hinge oven door during installation

(to provide the necessary handholds and to significantly

reduce the unit weight) can be cumbersome unless the

detailed door removal instructions are followed carefully.

Note: Do not attempt to remove the side hinge door (some

models).

Please take time to read and follow the instructions

provided for an improved installation experience.

Use this checklist to verify that you have completed each

step of the installation process. This can help you avoid

common mistakes.

__ 1. Before installing the oven, be sure to verify the

cabinet dimensions are correct for your unit and

the required electrical connections are present.

, Refer to the installation manual for content

regarding Safety, Cabinet Dimensions, Removing

Packaging, Electrical Installation, Testing the

Installation and Customer Service.

__ 3. Remove bottom hinged oven door(s) (not side

swing doors) to reduce the unit weight and to

provide access to handholds for lifting.

__ 4. Move the oven unit into place in front of the cabinet

opening, leaving the bottom packaging on the unit

to avoid damaging flooring.

__ 5 If installing a combination unit (oven and

microwave or oven and steam oven) complete the

assembly before installing the unit.

__ 6. Remove the torx head (T-20 size) screws holding

the unit to the base of the carton (using Star-head

screwdriver).

,

Team lift the unit directly into the cabinet cutout

taking care not to pinch fingers or scratch hands or

arms. Make sure the electrical conduit reaches to

the connection point properly.

__ 8. Slide the unit all the way into place, making sure to

route the electrical conduit correctly.

__ 9. Fasten the oven unit to the cabinetry opening with

the screws supplied (using Philips screwdriver).

__ 10. Reinstall the oven door(s) removed in step 3

above.

__ 11. Consult the complete installation instructions and

follow the remainder of the procedures listed,

including performing an operation test.

__ 12. All product literature and accessories (may be

wrapped or boxed) with the oven.

__ 13. INSTALLER - Leave the literature pack and the

accessories with the customer.

9000989321 Rev A English 3

Dimensions and Cabinet Requirements

Cabinet requirements vary depending on the model to be

installed. Please consult the "Cabinet Dimension

Requirements" section at the back of this installation

manual for the details pertaining to your particular model.

All models require:

1/4" (6.4 mm) space between the side of the oven and

an adjacent wall or cabinet door when installed at the

end of a cabinet run.

Installation of 2x4's extending front to back flush with

the bottom and side of the opening to provide oven

support. This supporting base must be well secured to

the floor/cabinet and must be level.

The electrical conduit box must be located above the

unit to facilitate connecting and servicing the unit.

The cabinet base must be flat and capable of

supporting the weight of your oven when in use (varies

by model up to 429 Ibs. (195 kg)). See the appropriate

weight for your model in the "Cabinet Dimensions

Requirements" section at the back of this installation

manual.

Removing Packaging

• Cut straps on the outside of the box.

• Remove the cardboard box by lifting it up and off the

unit.

• Remove all top and side cardboard and Styrofoam

braces.

• Place the oven (leaving it on the shipping base) in front

of the cabinet where it is to be installed.

Remove all accessories, racks, packing materials and

literature from the oven cavity (for double ovens,

remove such items, if present, from both cavities).

Unscrew unit from packaging brackets as shown below

in "Packaging Bracket Removal."

Note: The screws near the base mounting bracket are

all torx head (T-20 size). Only the one screw that goes

through the slotted hole in the mounting bracket on the

left and right sides of the unit needs to be removed in

order to lift the unit from the mounting base (the screw

circled and shown as "A" in the following illustration.)

NOTICE

Remove one screw only from each bracket. This

will release your oven from the shipping base. Do

not remove any additional screws from the oven.

Packaging Bracket Removal (left and right

sides)

Note:

Different models use different packaging materials. Actual

brackets may look differently. The bracket remains in the

packaging base. The unit should stay on the packaging

base until ready to be lifted into cabinet cutout.

Preparing Oven

Place oven in front of the cabinet where it is to be installed

so that it is in line with the cabinet cutout.

Check to be sure all packing materials have been removed

from the unit. Also remove the accessories, oven racks,

literature pack and any shipping materials from inside the

oven cavity (remove from both cavities for a double oven or

combination oven).

English 4 9000989321 Rev A

Installation

Determine the Installation Type

This installation manual provides instructions for the

installation of single ovens, double ovens, and combination

ovens (a single oven combined with microwave or steam

oven).

Stand-alone single and double oven units require no

pre-assernbly. Unless you are installing a combination

oven, skip over the combination oven pre-assembly

instructions and go directly to "Electrical Installation"

which applies to all ovens.

Pre-Assembly of Combination Ovens

Prior to Installation

Combination ovens (with microwave or steam oven)

require the units to be assembled together prior to installing

the combination unit into the wall cabinet.

Note: The single oven can be installed with a Steam Oven

or with a Microwave Oven. The installation procedure

differs between these. The parts contained in the square

tube parts box are common to both installations.Parts

Provided

Combination Oven Installation

Installation with the Microwave Oven

Note: Do not place the oven into the wall cabinet until after

mounting the microwave on it using the universal connector

brackets.

1. The combo service slide assemblies are attached to

the oven spaced to accept the microwave.

2. Install both universal connector brackets using six of

the screws provided. Tighten screws securely, but do

not overtighten.

Note: The universal connector brackets are interchange-

able for the left and right sides of the oven. Be sure the

taller vertical edge of the bracket is positioned to the out-

side of the oven.

Universal connector

bracket (2)

(in parts box on top of

oven)

Screws (16)

(in red bag, inside parts

box on top of oven)

Oven Mounting Screws

8 screws are included to

secure the oven trim to the

cabinet. The screws are

located in a small plastic

bag affixed to the literature

pack bag.

Combo service slide

assembly (2)*

* This part is

preassembled on the

oven to accomodate

attachment of a

microwave.

3. Install the decorative trim.

Position the decorative trim

piece so the flanges with

the holes in them face

away from the oven door.

Align the outer flanges with

the outside of the universal

brackets. Fasten with 1

screw each into the end

hole of the universal

bracket. Tighten screws

securely, but do not

overtighten.

9000989321 Rev A English 5

ii:il]_iO!_l'liii::]i_ii!ii%:ili!_:!iiiiiiiOi;i_OV,@I;I_!i::::_l@di!i_!!il;,_!!ii)@i!?liii::]iii!J

,

Place the microwave oven unit on top of the universal

connector brackets and fasten in place using three

screws per side. Tighten the screws securely, but do

not overtighten.

Note: The existing screws in the microwave base help

with alignment. When lowering the microwave into

place on the universal connector bracket, allow these

screw heads to slide into the slots as shown in the

illustration below. The screw nearest the front of the

microwave slides into the base of the slope at the front

of the bracket.

,

The screw in position A (nearest the inside edge, near

control panel) must be moved to allow the universal

bracket to be postioned there. Remove the inside

screw (A) from the left support bracket and reinsert it

into the third hole (B) from the inside edge of the

support bracket. Repeat for the right support bracket.

A

5. Continue with the unit installation in the following

sections on electrical connection and installing the

oven unit into the wall cabinet.

Installation with the Steam Oven

Note: Do not place the oven into the wall cabinet until after

mounting the steam oven on it using the universal connec-

tor brackets.

,

Remove the six screws holding the combo service slide

assemblies to the support bracket. Use a magnetic

screwdriver bit to reach the screws through the large

holes in the tops of the slides.

,

Reattach the slide assemblies using the holes near the

inside edge of the support bracket. Align the slide

assembly parallel to the edge of the bracket and insert

the first screw in hole (C). Insert all three screws for

each slide assembly. Tighten the screws securely, but

do not overtighten.

Note: When the correct holes are used, the front of the

slide assembly will extend just past the edge of the horizon-

tal support bar. The slide assembly will be about 118" (3

mm) from the inside edge of the support bracket.

4. Install the two universal connector brackets to the slide

assemblies using the screws provided. Tighten screws

securely, but do not overtighten.

English 6 9000989321 Rev A

Note: The universal connector brackets are interchange-

able for the left and right sides of the oven. Be sure the

taller vertical edge of the bracket is positioned to the out-

side of the oven.

Q

5. Install the decorative trim.

Position the decorative trim

piece so the flanges with

the holes in them face

away from the oven door.

Align the inner flanges with

the inside of the universal

brackets. Fasten with one

screw each into the end

hole of the universal

bracket. Tighten screws

securely, but do not

overtighten.

,

Place the steam oven unit on top of the universal

connector brackets and fasten in place using two

screws per side. Tighten the screws securely, but do

not overtighten.

Note: The existing screws in the steam oven base help

with alignment. When lowering the steam oven into

place on the universal connector bracket, allow these

screw heads to slide into the slots as shown in the

illustration below. The screw nearest the front of the

steam oven slides into the base of the slope at the front

of the bracket.

7. Continue with the unit installation in the following

sections on electrical connection and installing the

oven unit into the wall cabinet.

Connecting the Microwave Oven or Steam Oven

Electrical Conduit to the Single Oven

Note: If installing the oven with a microwave or steam oven

mounted as a combination unit, the microwave oven or

steam oven power cable must be properly attached to the

oven-mounted junction box. This must be done prior to

supplying electric power to the oven unit.

,_ WARNING

,

2.

3.

Disconnect the oven from the electric power supply

before connecting the microwave oven or steam

oven wiring. Failure to do so could result in electrical

shock and injury or death.

Check to be sure there is no electric power supplied to

the oven.

Remove the oven mounted junction box cover (located

on the rear top of the oven).

Remove the cap from the conduit access hole in the

side of the oven mounted junction box.

4. Guide the four wires from the conduit cable coming

from the microwave or steam oven through the hole in

the oven mounted junction box.

5. Snap the conduit connector into the hole by pressing it

in until it clicks into place.

6. Follow the wiring diagram label and match and connect

each wire by color to the wires attached to the wiring

block inside the oven mounted junction box. Push the

bare end of the wire until it is snug in the wiring block

then tighten down the retaining screw on each wire.

Tighten securely, but do not over tighten.

7. Replace the oven mounted junction box cover and

tighten the two screws holding it in place. Tighten the

screws securely, but do not over tighten.

9000989321 Rev A English 7

8. RefertotheElectricalConnectionsectionforfurther

informationtocompletetheelectricalconnectionofthe

combinationunittothemainpowersupply.

Electrical Installation

All model ovens on the front cover of this installation

instruction manual are dual rated, designed to be

connected to either 208 or 240V AC, 60 Hz, 4 wire, single-

phase power supply.

Model Circuit Required

208V, 60 Hz 240V, 60 Hz

HBN54, HBN84,

HBL53, HBL54, 30 AMP

HBL84, HBLP4

HBL55 30 AMP / 40 AMP

[

HBN56, HBL56,

HBL57, HBN86,

HBL86, HBL87,

HBLP6, HBLP7,

HSLP7

40 AMP

Four-wire Connection

Ungrounded Neutral

power supply

junction box

red wires

green or bare

wire

green wire

UL listed

connector

black wires

white wires

cable from

oven

• Connect the red oven wire to the red electrical supply

wire (hot wire).

• Connect the black oven wire to the black electrical

supply wire (hot wire).

• Connect the white neutral oven wire to the white

neutral (not bare or green ground) electrical supply

wire.

Connect the green ground oven wire to the bare or

green ground electrical supply wire.

Three-wire Connection

The electrical supply should be a 4-wire single-phase AC.

Install a suitable conduit box (not furnished). An

appropriately-sized, UL-listed conduit connector must be

used to correctly attach the conduit to the junction box.

Important: Local Codes may vary; installation, electrical

connections and grounding must comply with all applicable

local codes.

If local codes permit grounding through the electrical

supply neutral, connect both the white neutral wire and the

green ground wire from the oven to the white neutral

electrical supply wire.

Important: If you have purchased a combination oven unit

(one that includes a microwave or steam oven over the

single oven), see the preceding section "Connecting the

Microwave Oven or Steam Oven Electrical Conduit to the

Single Oven" showing electrical connection of the

combination unit components.

WARNING

Grounded Neutral

power supply

junction box .

red wires _2_,

white, bare, or

green wire

white wire

green wire

black wires

UL listed

connector

cable from

oven

• Connect red wire from oven to red wire in junction box.

• Connect black wire from oven to black wire in junction

box.

• Connect both green ground wire and white wire from

oven to white, green or bare neutral wire in junction

box.

The conduit cable, where connected at the oven, swivels.

Rotate conduit cable upward (or downward) and direct

through hole prepared in cabinet to attach to J-Box.

Complete the connection of the microwave or steam

oven conduit to the single oven before proceeding

with the unit electrical connection to the main power

supply.

To maintain serviceability, the flex conduit must not be

shortened and should be routed to permit temporary

removal of the oven.

Electrical Connection to Main Power Supply

The four-wire connection is preferred, but where local

codes permit, the three wire connection is also acceptable.

English 8 9000989321 Rev A

Installing the Oven Unit into

the Wall Cabinet

NOTICES

Before installing the oven, be sure to verify the

cabinet dimensions and electrical

connections.Check that the cabinet opening is level

and plumb for correct installation.

Combination units (ovens with a microwave or

steam oven) have additional installation instructions.

Please see the preceeding section "Pre-Assembly

of Combination Ovens Prior to Installation".

For Best Installation

The double and combination ovens can be difficult for two

people to handle during installation. It is recommended to

have three or more people available to assist with lifting the

unit into place. It is also recommended to remove the oven

door (bottom hinge models only) to help reduce the unit

weight and provide easier access to the handholds located

inside the oven.

Caution

: It is recommended to wear gloves and long sleeves to

protect hands and forearms from abrasion and potential

scratches during the lifting process. It is also recommended

to take off watches and jewelry and to wear work shoes

during installation for foot protection.

Correct Inside Oven Lift Point

Notice: DO NOT attempt to lift the unit by holding the oven

upper element.

There is a ridge across the top front of the oven cavity. Lift

by grasping this ridge with one hand while placing the other

hand on the back of the unit (for helpers lifting from the

sides of the unit). If a third helper is lifting from the front,

both hands should lift by holding this ridge area.

9000989321 Rev A English 9

Lifting Recommendations Vary Dependent Upon Oven Door Type

Bottom Hinge Door

Lift Locations (with door(s) removed)

Lift points (1) on the front of the unit are for lifting from the

sides of the unit. Lift point (3) on the front of the unit is for a

third person to help lift the unit.

Lift point (2) on the back of the unit shows the location of

the opposite hand for the helpers lifting from the sides of

the unit. Adjust the location as needed to facilitate the lift.

Wear gloves, a long sleeved shirt, and avoid sharp edges

to reduce the risk of cuts or abrasions to the arms or hands.

Single Oven Double/Combo Oven

q

O

Side Hinge Door

Lift Locations (with lower door opened to 90°-110 °)

Lift points (1) on the front of the unit are for lifting from the

sides of the unit. Lift point (3) on the front of the unit is for a

third person to help lift the unit.

Lift point (2) on the back of the unit shows the location of

the opposite hand for the helpers lifting from the sides of

the unit. Adjust the location as needed to facilitate the lift.

Wear gloves, a long sleeved shirt, and avoid sharp edges

to reduce the risk of cuts or abrasions to the arms or hands.

Single Oven - Side Swing Double Oven Side Swing

q

English 10 9000989321 Rev A

Installing the Oven

WARNING

• Make sure oven is cool and power to the oven

has been turned off before removing the door.

Failure to do so could result in burns.

• The oven door is heavy and fragile. Use both

hands to remove the oven door. The door front

is glass. Handle carefully to avoid breaking.

• Grasp only the sides of the oven door. Do not

grasp the handle as it may swing in your hand

and cause damage or injury.

• Failure to grasp the oven door firmly and

properly could result in personal injury or

product damage.

• To avoid injury from hinge bracket snapping

closed, be sure that both levers are securely in

place before removing the door. Also, do not

force door open or closed - the hinge could be

damaged and injury could result.

• Do not lay removed door on sharp or pointed

objects as this could break the glass. Lay on a

flat, smooth surface, positioned so that the

door cannot fall over.

Bottom Hinge Doors Only - Remove

Prior to Install

Important: Do not attempt to remove the side hinge

door (side hinge doors are found only on select models).

,

Holding the door firmly

on both sides and

using both hands,

close the door gently

until it stops against

the latch levers, about

30° from the closed

position.

,

Carefully lift the door

up and out of the

hinge slots. Hold

firmly; the door is

heavy.

, Place the door in a

convenient and stable

location until you are

ready to reinstall it.

Lay the door on a

towel or section of

protective foam

padding to avoid

damage to the door or

the floor.

Placing the Oven Into the Cabinet

Opening - All Ovens

Ovens with bottom hinge doors permit the oven door(s) to

be removed prior to lifting the unit into place. Each door

weighs approximately 40 pounds (18.1 kg). Removing and

replacing the door are routinely simple procedures.

Removing the door lightens the unit significantly and

provides easier access to the recommended handhold

inside the oven cavity. See instructions below.

, Be sure to read all

warnings and cautions

in the installation

manual regarding the

door removal before

attempting to remove

the door.

2. Open the door

completely.

3. Flip latch levers on

hinges toward you.

CAUTION

To avoid damage to the door do not lift, pull or push

the unit during installation by using the oven door

handle as a gripping point.

It is recommended to wear gloves and long sleeves

to protect hands and forearms from abrasion and

potential scratches during the lifting process. It is

also recommended to take off watches and jewelry

and to wear work shoes during installation for foot

protectio

When lifting the unit into place avoid grasping the upper

element to avoid damaging it. See the illustration following

for the correct lifting point for a bottom hinge double oven

with the lower door removed. This illustration shows a

detailed view of the oven cavity. Note the location of the

ridge inside the top of the cavity. This is the area to grip

from the front when lifting the oven.

For your particular oven type, see the preceeding section

"Lifting Recommendations Vary Dependent Upon Oven

Door Type" for lift points.

9000989321 Rev A English 11

Installing the Oven into the Cabinet (all

ovens)

1. The unit and its bottom packaging (wood and

styrofoam base) should be positioned close to and in

front of the cabinet opening prior to beginning to lift the

unit into place.

2. Lift or slide unit into the cabinet cutout without allowing

the unit base to contact the flooring.

3. Check that the conduit cable does not fall behind the

unit during installation. It may help to run the conduit

into the area it will be connected to (such as an

overhead or adjacent cabinet) and tape the end down

so it doesn't fall out while the unit is being slid into

place.

4. Guide the unit straight back into the cabinet cutout.

Note: Be careful not to crimp the flexible conduit

between the oven and the cabinet back wall. If

necessary, guide the flexible conduit into the wall or

cabinet access hole so it doesn't prevent the unit from

being pushed all the way into the cabinet opening. The

oven should be straight and level, not crooked.

5. Push the unit straight in until the oven trim is flush with

the front of the cabinet trim.

6. Install supplied screws through tap holes in trim.

(2 screws for single ovens, 4 screws for double/combo

ovens).

English 12 9000989321 Rev A

Ovens with Bottom Hinge Doors Only Ovens with Side Hinge Doors Only

Re-Install the oven doors:

1. Hold the door firmly in

both hands.

, Hold the door at a 30°

angle from the closed

position and insert

hinges into the slots.

You may need to rock

the door forward and

backward slightly to

seat the hinge feet.

,

The door may need to

be removed and re-

inserted until the

hinges sit correctly in

the slots.

4. Open door all the way

to expose hinges,

latch levers, and slots.

5. Push latch levers

forward and down until

seated on the bracket.

,

Close and open door

slowly to be sure it is

correctly and securely

in place. Door must be

straight, not crooked.

Side Hinge Door Aligment

Note: Only align the side hinge oven doors after the unit is

fully installed into the cabinet.

Fig. A

Fig. B

,

Check to see if the

side hinge oven doors

are properly aligned.

The door should pull

itself closed smoothly

when the striker

engages the roller as

the door is closed.

Too high (Fig. A - door

needs to move down

on latch side) you will

feel interference

between the striker

and the catch receiver.

Too low (Fig. B - door

needs to move up on

latch side) you will feel

a bump when the

striker comes into

contact with the re-

alignment roller.

Hint: The gap between

the top of the closed

oven door and the

control panel (or upper

door for lower cavities

in double ovens)

should be fairly

uniform from side to

side.

9000989321 Rev A English 13

Side Hinge Door Alignment Procedure

Open the door to

approximately 135°.

Using a Torx T-20 star-

head screwdriver,

loosen the 3 screws

(A) on the lower hinge

by 1 to 2 full turns.

Note: All adjustment is

made with the lower

hinge only. The upper

hinge is fixed in place

and cannot be

adjusted.

__ 3.

Using a #2 philips

head screwdriver, turn

the cam (B) right or left

to adjust the hinge

position in the desired

direction.

Note: lmm of hinge

movement (left or

right) will move the

door up or down

approximately 1.5mm

at the door catch.

4. Re-tighten the screws

before closing the

door to test. Be careful

not to overtighten.

5. Check for proper door

alignment. Repeat

adjustment procedure

as necessary.

English 14 9000989321 Rev A

Primaryobservation

Thedoordoesnotpull

itselfclosedandfeels

difficulttoopenaswell.

Thedoordoesnothold

itselfclosed.

Thedoordoesnotclose

ontothestriker

smoothly.

Onceclosed,thedoor

openswithoutincident.

Thedoordoesnotclose

ontothestriker

smoothly.

Onceclosed,thedoor

mayalsoappearto

stickwhilepullingthe

dooropen

SideHingeDoorOpening/ClosingTroubleshootingGuide

Additionalobservations Cause: Solution

Thesideedgeoftheinner

door(onthehandlesideof

thedoor)appearstomake

contactwiththeunit'sside

trim.

Verylittleforceisrequired

topullopenthedoor.

Whenclosingthedooronto

thestriker,thedoorlifts

itselfupwards.

Youwillfeelaslightbump

astheroller(internaltothe

door)hitsthetipofthe

strikerandliftsthedoor.

Ifthedoorneedstolift

substantially,thedoorwill

nolongerpullitselfclosed,

andassistanceisrequired

topushitclosedfully.

Whiletryingtoopenthe

doorfromaclosedposition,

youfeelaninterferencethat

catchesthedoorandmay

preventitfromopening.

Youfeelasimilar

interferencewhenclosing.

Theinstallationis

causingtheside

trimtobepushed

toofarinwards.

Thedoorcatch

mechanism

internaltothe

doorhas

inadvertently

trippedwhilethe

doorwasopen.

Thedoor

alignmentistoo

lowtoengage

properlywiththe

striker.

SeefigureBinthe

sidehingedoor

alignment

instructions.

Thedoor

alignmentistoo

hightoengage

properlywiththe

striker.

SeefigureAinthe

sidehingedoor

alignment

instructions.

Checktheinstallationoftheunitinthe

cabinetry.Trytomovetheunitinthecabinet

towardsthesideofthehingesasmuchas

possibletoallowtheinterferingsidetrimto

openup.

Mayalsotrytoadjustthelocationoftheside

trimscrewstoholdthetrimawayfromthe

door.

Checkagainthecabinetopeningtoensure

thatitisnottoonarrow.Widenthecutoutas

necessary.

Toresetthemechanism,closethedoor

completelyandwhileclosed,pushinfirmlyon

thedoorhandleuntilthemechanismresets.

Afirmpushmayberequired.Opentotest.

Refertothesidehingedooralignment

proceduretoraisethehandlesideofthedoor

untilthedoorclosessmoothly.

Itshouldopensmoothlyandpullitselfclosed

smoothlywithouthearingorfeelingan

interference.

Toopenastickingdoor,applypressure

downwardonthehandlewhilepulling.

Refertothesidehingedooralignment

proceduretolowerthehandlesideofthedoor

untilthedoorclosessmoothly.

Itshouldopensmoothlyandpullitselfclosed

smoothlywithouthearingorfeelingan

interference.

9000989321RevA English15

Testing Operation Data Plate

1. Turn on power at the breaker.

2. Test the oven mode.

Select the BAKE mode. See the Use and Care Manual

for detailed operation instructions.

3. Verify that the oven light comes on and the oven begins

to preheat.

4. Test the door lock.

Set the SELF CLEAN mode. Confirm that the door

locks when the lock icon appears in the display.

5. If installing a double oven, test the second oven as

well.

6. If any of the tests do not result as explained above,

contact Bosch service for assistance. Otherwise, the

installation is complete at this time.

Before Calling Service

Seethe Use and Care Manual for troubleshooting

information. Refer to the Statement of Limited Warranty in

the Use and Care Manual.

To reach a service representative, see the contact

information at the front of the Use and Care Manual.

Please be prepared with the information printed on your

product data plate when calling.

The data plate shows the model and serial number. Refer

to the data plate on the appliance when requesting service.

The data plate location varies based on the oven model

and door hinge type.

Double Ovens, Bottom Hinge

Note: The rating plates (A) are at the left hand side of

the door trim of the lower oven cavity.

Single Ovens, Bottom Hinge

Note: The rating plates (A) are at the left hand side of

the door trim.

English 16 9000989321 Rev A

Single Ovens, Side Hinge

Note: The rating plates (A) are opposite the door hinge.

For left hinge doors, the rating plates will be on the door

trim on the right hand side of the door. For right hinge

doors, the rating plates will be on the door trim on the

left hand side of the door.

Double Ovens, Side Hinge

Note: The rating plates are opposite the door hinge in

the lower oven cavity.

9000989321 Rev A English 17

Cabinet Dimension Requirements

It is good practice, when an oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall, or cabinet

door, to allow at least 1/4" (6 mm) space between the side

of the oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Junction boxes can be located anywhere within reach of

the oven's power cable.

Dimensions for 27" Single

Oven Units

The cabinet opening must be plumb and the base must be

flat and level and capable of supporting a weight of at least

193 Ibs (87 kg).

Single Oven 27" Traditional Installation,

Cabinet and Undercounter

min.

m

a×. 38

(121

measurements in inches (ram)

Single Oven 27" Flush Mount

Installation

Flush installation (wall mount and undercounter) requires

two side cleats to be attached inside the cabinet or counter

frame, recessed from the front.

Fi;ush Ins_ai_ Te_ View Sde View

{218}

<__

24_W '__

(022)

(25)

(740)

flush

height

meas#rem_s [r_ineh_s (ram)

Dimensions for 27" Double

Oven Units

The cabinet opening must be plumb and the base must be

flat and level and capable of supporting a weight of at least

361 Ibs (164 kg).

Double Oven 27" Traditional

Installation

50"

_ (1270)

493/4"-511/2"

(1264-1308)

521/16" 49518. min.

(1323) (1260) (121

English 18 9000989321 Rev A

La page charge ...

Bosch HBL5751UCC/02 Guide d'installation

Ce manuel convient également à

Bosch HBL5751UCC/02 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents