Panasonic PVGS9 Mode d'emploi

Before attempting to connect, operate or adjust this product, please

read these instructions thoroughly.

LSQT0803 A

PV-GS9

PV-GS13

PV-GS15

Digital Video Camcorder

Operating Instructions

Models No.

For assistance, please call : 1-800-561-5505 or visit us at www.panasonic.ca

(PV-GS15 Shown)

[For PV-GS13/PV-GS15] [For PV-GS13/PV-GS15]

2

WARNING :

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOISTURE.

Date of Purchase

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

You have purchased one of the most

sophisticated and reliable products on the

market today. Used properly, we’re sure it will

bring you and your family years of enjoyment.

Please take time to ﬁ ll in the information on the

right.

The serial number is on the tag located on the

underside of your Camcorder. Be sure to retain

this manual as your convenient Camcorder

information source.

This symbol alerts the user that important

literature concerning the operation and

maintenance of this unit has been included.

Therefore, it should be read carefully in order to

avoid any problems.

The above markings are located on the appliance bottom cover.

Your

Camcorder is designed to record and play back in Standard Play (SP) mode and Long (LP)

mode.

It is recommended that only cassette tapes that have been tested and inspected for use in VCR machines

with the mark be used.

Thank you for choosing Panasonic!

This symbol warns the user that uninsulated

voltage within the unit may have sufﬁ cient

magnitude to cause electric shock. Therefore, it

is dangerous to make any kind of contact with

any inside part of this unit.

Things You Should Know

Safety Precautions

3

WARNING

AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO NOT

ALLOW CHILDREN TO HANDLE THE SD CARD.

CAUTION:

TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING

INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO

WIDE SLOT, FULLY INSERT.

CAUTION:

DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

• Since this product gets hot during use, operate it in well ventilated place; do not install this equipment in

a conﬁ ned space such as a bookcase or similar unit.

This class B digital apparatus complies with CANADIAN ICES-003.

A lithium ion/polymer battery that is recyclable powers the product

you have purchased. Please call 1-800-8-BATTERY for information

on how to recycle this battery.

AT TEN TION:

4

11. Grounding or Polarization — This video unit may be

equipped with either a polarized 2-wire AC (Alternating

Current) line plug (a plug having one blade wider than

the other) or 3-wire grounding type plug, a plug having

a third (grounding) pin.

The 2-wire polarized plug will ﬁ t into the power outlet

only one way. This is a safety feature. If you are unable

to insert the plug fully into the outlet, try reversing the

plug. If the plug still fails to ﬁ t, contact your electrician

to replace your obsolete outlet. Do not defeat the

safety purpose of the polarized plug.

The 3-wire grounding type plug will ﬁ t into a grounding

type power outlet. This is a safety feature. If you are

unable to insert the plug into the outlet, contact your

electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the grounding type plug.

12. Power-Cord Protection — Power-supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords of plugs, convenience

receptacles, and the point where they exit from the

unit.

13. Outdoor Antenna Grounding — If an outside antenna

or cable system is connected to the video unit, be sure

the antenna or cable system is grounded so as to

provide some protection against voltage surges and

built-up static charges. Part 1 of the Canadian

Electrical Code, in USA Section 810 of the National

Electrical Code, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of antenna

discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

14. Lightning — For added protection of this video unit

receiver during a lightning storm, or when it is left

unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the

antenna or cable system. This will prevent damage to

the video unit due to lightning and power-line surges.

1. Read Instructions — All the safety and operating

instructions should be read before the unit is operated.

2. Retain Instructions — The safety and operating

instructions should be retained for future reference.

3. Heed Warnings — All warnings on the unit and in the

operating instructions should be adhered to.

4. Follow Instructions — All operating and maintenance

instructions should be followed.

5. Cleaning — Unplug this video unit from the wall outlet

before cleaning. Do not use liquid or aerosol cleaners.

Use a dry cloth for cleaning.

6. Attachments — Do not use attachments not

recommended by the video product manufacturer as

they may be hazardous.

7. Water and Moisture — Do not use this video unit near

water — for example near a bath tub, wash bowl,

kitchen sink, or laundry tub, in a wet basement, or near

a swimming pool, and the like.

8. Accessories — Do not place this video unit on an

unstable cart, stand, tripod, bracket, or table. The

video unit may fall, causing serious injury to a child or

adult, and serious damage to the unit. Use only with a

cart, stand, tripod, bracket, or table recommended by

the manufacturer, or sold with the video unit. Any

mounting of the unit should follow the manufacturer’s

instructions and should use a

mounting accessory

recommended by the

manufacturer. An appliance and

cart combination should be moved

with care. Quick stops, excessive

force, and uneven surfaces may

cause the appliance and cart

combination to overturn.

9. Ventilation — Slots and openings in the cabinet are

provided for ventilation and to ensure reliable operation

of the video unit and to protect it from overheating.

These openings must not be blocked or covered.

Never place the video unit on a bed, sofa, rug, or other

similar surface, or near or over a radiator or heat

register. This video unit should not be placed in a

built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

10. Power Sources — This video unit should be operated

only from the type of power source indicated on the

marking label. If you are not sure of the type of power

supply to your home, consult your appliance dealer or

local power company. For video units intended to be

operated from battery power, or other sources, refer to

the operating instructions.

Important Safeguards

5

15. Power Lines — An outside antenna system should not

be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can fall

into such power lines or circuits. When installing an

outside antenna system, extreme care should be taken

to keep from touching such power lines or circuits as

contact with them might be fatal.

16. Overloading — Do not overload wall outlets and

extension cords as this can result in a risk of ﬁ re or

electric shock.

17. Objects and Liquids — Never push objects of any kind

into this video unit through openings as they may touch

dangerous voltage points or short out parts that could

result in a ﬁ re or electric shock. Never spill liquid of any

kind onto the video unit.

18. Servicing — Do not attempt to service this video unit

yourself as opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all

servicing to qualiﬁ ed service personnel.

19. Damage Requiring Service — Unplug this video unit

from the wall outlet and refer servicing to qualiﬁ ed

service personnel under the following conditions:

a. When the power-supply cord or plug is damaged.

b. If any liquid has been spilled into, or objects have

fallen onto, the video unit.

c. If the video unit has been exposed to rain or water.

d. If the video unit does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions, as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualiﬁ ed technician to

restore the video unit to its normal operation.

e. If the video unit has been dropped or the cabinet

has been damaged.

f. When the video unit exhibits a distinct change in

performance — this indicates a need for service.

20. Replacement Parts — When replacement parts are

required, be sure the service technician has used

replacement parts speciﬁ ed by the manufacturer or

have the same characteristics as the original part.

Unauthorized substitutions may result in ﬁ re, electric

shock or other hazards.

21. Safety Check— Upon completion of any service or

repairs to this video unit, ask the service technician to

perform safety checks to determine that the video unit

is in safe operating order.

USE & LOCATION

• TO AVOID SHOCK HAZARD ... Your Camcorder and power supply should not be exposed to rain or moisture. Do not

connect the power supply or operate your Camcorder if it gets wet. Your Camcorder has been designed for outdoor

use, however, it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or direct splashing

from a pool or even a cup of coffee. This action could permanently damage the internal parts of your Camcorder. Do not

attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your Camcorder from the power

supply before cleaning.

Precautions

WARNING

• DO NOT AIM YOUR CAMCORDER AT THE SUN OR OTHER BRIGHT OBJECTS

• DO NOT LEAVE THE CAMCORDER WITH THE EVF AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE

DAMAGE TO THE INTERNAL PARTS OF THE EVF

• DO NOT EXPOSE YOUR CAMCORDER TO EXTENDED HIGH TEMPERATURE ... Such as, direct sunlight, inside a

closed car, next to a heater, etc... This action could permanently damage the internal parts of your Camcorder.

• AVOID SUDDEN CHANGES IN TEMPERATURE ... If the unit is suddenly moved from a cold place to a warm place,

moisture may form on the tape and inside the unit.

• DO NOT LEAVE YOUR CAMCORDER OR THE POWER SUPPLY TURNED ON WHEN NOT IN USE.

• STORAGE OF YOUR CAMCORDER ... Store and handle your Camcorder in a manner that will not subject it to

unnecessary movement (avoid shaking and striking). Your Camcorder contains a sensitive pick-up device which could

be damaged by improper handling or storage.

CARE

• TO CLEAN YOUR CAMCORDER ... Do not use strong or abrasive detergents when cleaning your Camcorder body.

• TO PROTECT THE LENS ... Do not touch the surface of the lens with your hand. Use a commercial Camcorder lens

solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.

• TO PROTECT THE FINISH OF YOUR CAMCORDER ... Before handling your Camcorder, make sure your hands and

face are free from any chemical products, such as suntan lotion, as it may damage the ﬁ nish.

CAUTION

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited viewing.

This product incorporates copyright protection technology that is protected by method claims of certain U.S.

patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.

Use of this copyright protection technology must be authorized by Macrovision Corporation, and is

intended for home and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

6

You (“Licensee”) are granted a license for the Software deﬁ ned in this End User Software Agreement

(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If Licensee does

not agree to the terms and conditions of this Agreement, promptly return the Software to Matsushita

Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from which you made the purchase.

Article 1 License

Licensee is granted the right to use the software, including the information recorded or described on the

CD-ROM, instruction manuals, and any other media provided to Licensee (collectively “Software”), but all

applicable rights to patents, copyrights, trademarks and trade secrets in the Software are not transferred to

Licensee.

Article 2 Use by a Third Party

Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to use,

copy or modify the Software, except as expressly provided for in this Agreement.

Article 3 Restrictions on Copying the Software

Licensee may make a single copy of the Software in whole or in part solely for back-up purpose.

Article 4 Computer

Licensee may only use the Software on a single computer at a single location.

Article 5 Reverse Engineering, Decompiling or Disassembly

Licensee may not reverse engineer, decompile, or disassemble the Software, except to the extent either of

them is permitted under law or regulation of the country where Licensee resides. Matsushita, or its

distributors or dealers will not be responsible for any defects in the Software or damage to Licensee

caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.

Article 6 Limitation of Liability

The Software is provided “AS-IS” without warranty of any kind, either expressed or implied, including, but

not limited to, warranties of non-infringement, merchantability and/or ﬁ tness for a particular purpose.

Further, Matsushita does not warrant that the operation of the Software will be uninterrupted or error free.

Matsushita or any of its distributors or dealers will not be liable for any damage suffered by Licensee

arising from or in connection with Licensee’s use of the Software.

Article 7 Export Control

Licensee agrees not to export or re-export to any country the Software in any form without the appropriate

export licenses under regulations of the country where Licensee resides, if necessary.

Article 8 Termination of License

The right granted to Licensee hereunder will be automatically terminated if Licensee violates any of the

terms and conditions of this Agreement. Upon such automatic termination, Licensee must destroy the

Software and related documentation together with all the copies thereof at Licensee’s own expense.

Before opening the CD-ROM package (PV-GS13 (LSFT0577)/PV-GS15 (LSFT0575): Supplied, PV-GS9:

Optional Software), please read the following.

End User License Agreement (for USB Driver, WebCam Driver

(PV-GS13/PV-GS15: Supplied, PV-GS9: Optional Software) and DV

STUDIO (PV-GS13: Supplied, PV-GS9/PV-GS15: Optional

Software))

7

This operating instruction book is designed for use with models PV-GS9, PV-GS13 and PV-GS15. The

PV-GS15 is the model used for illustrative purposes. Features may vary, so please read carefully.

Differences between models

Model

Number

PV-GS9 PV-GS13 PV-GS15

Battery Pack

(Supplied)

CGR-D08R

(800 mAh)

CGR-D08R

(800 mAh)

CGR-D14

(1 350 mAh)

Memory

Card

Supplied (RP-SD008MMK0) Supplied (RP-SD008MMK0)

CD-ROM Optional Software Supplied (LSFT0577) Supplied (LSFT0575)

USB Cable Optional Supplied (K1HA05CD0005) Supplied (K1HA05CD0005)

Lens

f2.1-42 mm, F1.8-3.1

(35 mm equivalent:

39.5-790 mm),

20x zoom lens

f2.1-46.2 mm, F1.8-3.4

(35 mm equivalent:

39.5-869 mm),

22x zoom lens

f2.1-50.4 mm, F1.8-3.6

(35 mm equivalent:

39.5-948 mm),

24x zoom lens

Photoshot

(Tape)

Feature

Yes No No

Mode Dial

(Tape Recording Mode)

(Tape Playback Mode)

(Tape Recording Mode)

(Tape Playback Mode)

(Card Recording Mode)

(Picture Playback Mode)

(Tape Recording Mode)

(Tape Playback Mode)

(Card Recording Mode)

(Picture Playback Mode)

Card

Feature

No Yes Yes

Viewﬁ nder Electronic Viewﬁ nder Electronic Viewﬁ nder

Liquid Crystal Colour Electronic

Viewﬁ nder

LED Video

Light

No Yes Yes

S-Video

Output Jack

No No Yes

Microphone

Jack

No No Yes

8

Contents

Before Use

Things You Should Know ....................................2

Safety Precautions ..............................................2

Important Safeguards..........................................4

Precautions .........................................................5

End User License Agreement..............................6

Differences between models ...............................7

Quick Guide.......................................................10

Standard Accessories........................................12

Controls and Components.................................12

The Remote Control ..........................................15

Power Supply ....................................................16

Charging Time and Available Recording Time...16

The Grip Belt .....................................................17

Re-attaching the Lens Cap................................17

Attaching the Shoulder Strap ............................17

Inserting a Cassette ..........................................17

Using a Memory Card

(For PV-GS13/PV-GS15).................................18

Turning on the Camcorder.................................18

Easy to Use Mode Dial......................................18

Using the Viewﬁ nder/LCD Monitor ....................19

Using the Menu Screen.....................................19

List of Menus .....................................................20

Setting Date and Time .......................................23

Internal Lithium Battery Recharge.....................23

LP Mode ............................................................23

Audio Recording Mode......................................23

Recording Mode

About Recording................................................24

Recording on a Tape .........................................24

Recording a Still Picture on a Tape

(PV-GS9 Only).................................................25

Recording a Still Picture on a Card (Photoshot)

(For PV-GS13/PV-GS15).................................25

Recording Yourself ............................................26

Recording with the Built-in LED Video Light

(For PV-GS13/PV-GS15).................................26

Quick Start.........................................................26

Self-timer Recording..........................................27

Zoom In/Out Functions......................................27

Digital Zoom Function .......................................27

Image Stabilizer Function..................................28

Fade In/Out Functions.......................................28

Backlight Compensation Function.....................29

MagicPix Function .............................................29

Soft-Skin Mode..................................................29

Wind Noise Reduction Function ........................29

Cinema Function ...............................................29

Recording in Special Situations.........................30

Recording in Natural Colours ............................30

Adjusting White Balance Manually ....................31

Manual Shutter Speed Adjustment ....................32

Manual Iris Adjustment ......................................32

Manual Focus Adjustment .................................32

Digital Effect Functions......................................33

9

Playback Mode

Playing Back a Tape ..........................................35

Finding a Scene You Want to Play Back ...........35

Slow Motion Playback (Remote Control Only) ..36

Still Playback/Still Advance Playback ................36

Index Search Functions

(Remote Control Only) ....................................37

Playback Zoom Function

(Remote Control Only) ....................................37

Playback Digital Effect Functions ......................38

Playing Back a Memory Card

(For PV-GS13/PV-GS15).................................38

Slide Show

(For PV-GS13/PV-GS15).................................39

Creating a Title

(For PV-GS13/PV-GS15).................................40

Adding a Title

(For PV-GS13/PV-GS15).................................40

Writing Printing Data on a Card

(For PV-GS13/PV-GS15).................................41

Protecting the Files on a Card

(For PV-GS13/PV-GS15).................................41

Deleting the Files Recorded on a Card

(For PV-GS13/PV-GS15).................................42

Formatting a Card

(For PV-GS13/PV-GS15).................................42

Playing Back on Your TV ...................................43

Editing Mode

Recording from a Tape onto a Card

(For PV-GS13/PV-GS15).................................44

Recording Pictures from a Card onto a Tape

(For PV-GS13/PV-GS15).................................44

Audio Dubbing (Remote Control Only)..............44

Copying on an S-VHS (or a VHS) Cassette ......45

Using the DV Cable for Recording ....................45

PC Connection With DV Interface Cable...........46

With a PC

Using the Software with a Personal Computer..47

Using USB Driver ..............................................47

To disconnect USB cable safely ........................49

Using as a Web Camera ...................................50

Using the DV STUDIO 3.1E-SE

(PV-GS13: Supplied;

PV-GS9/PV-GS15: Optional Software)............54

Using the ArcSoft Software

(PV-GS15: Supplied) .......................................55

If you no longer need software or driver

(Uninstall) ........................................................57

Notes .................................................................57

Others

Indications .........................................................59

Initializing the Modes.........................................60

Warning/Alarm Indications.................................60

Notes and Hints.................................................61

Cautions for Use................................................65

Before Requesting Service

(Problems and Solutions) ................................69

Using the RESET button ...................................70

Explanation of Terms .........................................71

Speciﬁ cations ....................................................72

Camcorder Accessory System ..........................73

Warranty ............................................................74

Index..................................................................75

10

Before Use

Quick Guide

• Before use, fully charge the Battery.

• Since the Battery will not be charged when the DC

Cable is connected to the AC Adaptor, disconnect

it from the AC Adaptor.

• The [POWER] Lamp and [CHARGE] Lamp light

up, and charging starts.

• When the [CHARGE] Lamp goes off, charging is

completed.

1 Attach the Battery to the AC Adaptor and

charge it.

2 Attach the charged Battery to the Camcorder.

1 Slide the [OPEN/EJECT] Lever

1

toward the

front and pull down to fully open the Cassette

Compartment Cover.

• To protect the tape, if the cover is not fully opened,

the cassette cannot be ejected.

2 Insert a Cassette.

3 Close the Cassette Holder by pressing the

[PUSH] mark

2

.

4 Close the Cassette Compartment Cover by

pressing the mark

3

.

2

1

Inserting a Cassette

Inserting a Card

(For PV-GS13/PV-GS15)

2 Slide the [OPEN] Lever

3

to open the Card

Slot Cover

4

.

3 While holding the Memory Card with its cut

corner facing right

5

insert it into the Card

Slot

6

.

4 Close the Card Slot Cover

4

securely.

5

3

4

6

Recording on a Tape

1 Set the [OFF/ON] Switch

1

to [ON].

• The [POWER] Lamp

2

lights up.

2 Set the Mode Dial to Tape Recording Mode.

3 Press the Recording Start/Stop Button.

• Recording starts.

(PV-GS13/

PV-GS15)

(PV-GS9)

1

2

4 Press the Recording Start/Stop Button again

to pause the recording.

3

1 Place your Thumb on the [OPEN▼] Knob

1

and pull the LCD Monitor

2

out in the

direction of the arrow.

2

1

11

Before Use

Recording a Still Picture on Tape

(PV-GS9 Only)

2 Press the [PHOTO SHOT] Button in the

Recording Pause Mode.

1 Set the Mode Dial to Card Recording Mode.

2 Press the [PHOTO SHOT] Button.

Recording a Still Picture on Card

(Photoshot)

(For PV-GS13/PV-GS15)

1 Set the [OFF/ON] Switch

1

to [ON].

• The [POWER] Lamp

2

lights up.

2 Set the Mode Dial to Tape Playback Mode.

3 Press the [

] Button to rewind the tape.

4 Press the [►] Button to start playback.

5 Press the [

] Button to stop playback.

(PV-GS13/

PV-GS15)

(PV-GS9)

Playing Back a Tape

1

2

1 Set the Mode Dial to Picture Playback Mode.

► : Starting the Slide Show

: Playing back the next picture

: Playing back the previous picture

: Stop the Slide Show

: Pause the Slide Show

2 Start Playback.

Playing Back a Card

(For PV-GS13/PV-GS15)

1 Set the Mode Dial to Tape Recording Mode.

12

Before Use

Standard Accessories

Illustrated are accessories supplied with the

Camcorder.

1) AC Adaptor, DC Cable and AC Cable

(p. 16)

1)

2) 3)

4) 5) 6)

7)

PV-DAC11-K

LSSQ0411

LSJA0280 LSFC0018

RP-SD008MMK0

(For PV-GS13/

PV-GS15)

K1HA05CD0005

(For PV-GS13/

PV-GS15)

LSFT0577

(PV-GS13 Only)

LSFT0575

(PV-GS15 Only)

2) Battery Pack (p. 16)

3) Remote Control and Button-Type Battery

(p. 15)

4) AV Cable (pp. 43, 45)

5) Shoulder Strap (p. 17)

6) SD Memory Card (For PV-GS13/PV-GS15)

(p. 18)

7) USB Connection Kit (USB Cable and

CD-ROM) (PV-GS13 (LSFT0577)/PV-GS15

(LSFT0575)) (pp. 47-49, 51, 54)

CAUTION:

This unit will operate on 110/120/220/240 V AC.

An AC plug adaptor may be required for

voltages other than 120 V AC. Please contact

either a local or foreign electrical parts distributor

for assistance in selecting an alternate AC plug.

We recommend using the accessory power plug

adaptor (VJSS0070/KZDB4ZE00001) in an area

which has special AC outlets.

Controls and Components

Camcorder

CGR-D14

(PV-GS15 Only)

CGR-D08R

(For PV-GS9/

PV-GS13)

1

2

3 4 5

6

7 8 9

1

LCD Monitor Open Knob [OPEN▼] (p. 19)

2

LCD Monitor (pp. 19, 68)

19

20

21

12

11

10

13 14 15 16 17

18

3

Card Slot Cover Open Lever [◄OPEN]

(For PV-GS13/PV-GS15) (p. 18)

4

Card Slot (For PV-GS13/PV-GS15) (p. 18)

5

Card Slot Cover (For PV-GS13/PV-GS15)

(p. 18)

6

Speaker (p. 35)

7

Recording Check Button [ ] (p. 24)

Recording Button [REC] (p. 46)

8

MagicPix Button [MAGICPIX] (p. 29)

9

Soft Skin Button [SOFT SKIN] (p. 29)

10

Backlight Button [BACK LIGHT] (p. 29)

11

Light Button [LIGHT]

(For PV-GS13/PV-GS15) (p. 26)

12

Card Access Lamp

(For PV-GS13/PV-GS15) (p. 18)

13

Pause Button [ ] (p. 25)

Still Button [STILL] (p. 25)

14

Fast Forward/Cue Button [ ] (p. 35)

15

Play Button [►] (p. 35)

Enter Button [ENTER] (p. 20)

16

Stop Button [ ] (p. 35)

Fade Button [FADE] (pp. 28-29)

17

Rewind/Review Button [ ] (p. 35)

Due to limitations in LCD production technology,

there may be some tiny bright or dark spots on

the LCD Monitor screen.

However, this is not a malfunction and does not

affect the recorded picture.

LSJA0288 K2CB2CB00014

CR2025

13

Before Use

18

Mode Selector Switch

[AUTO/MANUAL/FOCUS] (pp. 24, 30-32)

19

Menu Button [MENU] (p. 19)

20

Multi Button [MULTI] (p. 33)

Picture-in-Picture Button [P-IN-P] (p. 34)

21

Reset Button [RESET] (pp. 60, 70)

25

24

23

22

26

22

Lens Hood (p. 69)

23

Lens

24

Microphone (built-in, stereo) (pp. 27, 29)

25

Built-in LED Light

(For PV-GS13/PV-GS15) (p. 26)

26

Zoom Lever [W/T] (pp. 27-28, 35)

27

28

29 30

32 33

31

33

Microphone Jack [MIC] (PV-GS15 Only)

• When connecting an external microphone

or audio equipment to this jack, the built-in

microphone does not operate.

• A compatible plug-in powered microphone can

be used. Please consult your dealer for more

information.

• The microphone may make noises depending

on the type used. In this case, we recommend

using the battery with the Camcorder to reduce

noises instead of the AC Adaptor.

35

Eyepiece Corrector Knob (p. 19)

36

Photoshot Button [PHOTO SHOT]

(pp. 25-26)

37

Cassette Eject Lever [OPEN/EJECT] (p. 17)

38

DC Input Jack [DC IN] (p. 16)

39

S-Video Output Jack [S-VIDEO OUT]

(PV-GS15 Only) (pp. 43, 45)

40

Mode Dial (p. 18)

41

Power Lamp [POWER] (p. 18)

42

Quick Start Recording Button [QUICK

START] (p. 26)

Quick Start Recording Lamp (p. 26)

43

Recording Start/Stop Button (p. 24)

44

Power Switch [OFF/ON] (pp. 18, 24)

34

Viewﬁ nder (pp. 19, 68)

34 35 36 37

38

39

40

4241

43

44

Due to limitations in LCD production technology,

there may be some tiny bright or dark spots on

the Viewﬁ nder screen.

However, this is not a malfunction and does not

affect the recorded picture.

27

Cassette Holder

28

Cassette Compartment Cover (p. 17)

29

USB Jack [ ] (pp. 48-49, 51, 54)

30

DV Input/Output Terminal (pp. 45-46)

• Connect this to the digital video equipment.

31

White Balance Sensor (p. 31)

Remote Control Sensor (p. 15)

32

Audio-Video Output Jack [AV OUT]

(pp. 43, 45)

Headphone Jack [PHONES]

• Connecting an AV Cable to this jack activates

the Camcorder’s built-in speaker, but

connecting a headphone, etc. deactivates it.

• When connecting the pin plug of the AV Cable

to this jack, plug it in as far as it goes.

• When using headphones, set [INITIAL] >> [AV

JACK] >> [OUT/PHONES].

14

Before Use

Remote Control

Using the wireless Remote Control that is supplied

with the Camcorder, most of the Camcorder

functions can be operated from a distance.

The following buttons function in the same manner as

the corresponding buttons on the Camcorder.

45

Shoulder Strap Holders (p. 17)

46

Grip Belt (p. 17)

47

Battery Holder

48

Battery Eject Switch [BATTERY RELEASE]

(p. 16)

49

Tripod Receptacle

• Used for mounting the Camcorder on an

optional tripod.

65

Photoshot Button [PHOTO SHOT]

(pp. 25-26)

66

Title Button [TITLE] (p. 40)

67

Multi-Picture/Picture-in-Picture Button

[MULTI/P-IN-P] (pp. 33-34)

68

Rewind/Review Button [ ] (p. 35)

69

Pause Button [ ] (pp. 36, 44-45)

70

Stop Button [ ] (pp. 37, 45)

71

Recording Start/Stop Button [START/STOP]

(p. 24)

72

Play Button [►] (pp. 36, 45)

73

Fast Forward/Cue Button [ ] (p. 35)

74

Playback Zoom Button [P.B. ZOOM] (p. 37)

75

Enter Button [ENTER] (p. 20)

50

Date/Time Button [DATE/TIME] (p. 60)

51

Indication Output Button [OSD] (p. 43)

52

Display Button [DISPLAY] (p. 60)

53

Reset Button [RESET] (pp. 60, 70)

54

Recording Button [ REC] (p. 45)

55

Audio Dubbing Button [A.DUB] (p. 44)

56

Cursor buttons for Variable Speed Search

Function [▲, ▼] (p. 36)

Direction Buttons for Playback Zoom

Function [▲, ▼, ◄, ►] (p. 37)

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

57

Slow Motion/Still Advance Buttons [ , ]

( : reverse, : forward) (p. 36)

58

Index Search Buttons [ , ]

( : reverse, : forward) (p. 37)

59

Selection Button [SELECT] (p. 38)

60

Store Button [STORE] (p. 38)

61

Off/On Button [OFF/ON] (p. 38)

62

Zoom/Volume Button [ZOOM/VOL]

(p. 38)

63

Variable Speed Search Button

[VAR.SEARCH] (p. 36)

64

Menu Button [MENU] (p. 19)

65

66

67

68

69

70

71

72

73

74

75

45 46

47 48 49

15

Before Use

The Remote Control

Inserting the Button-type Battery

Before using the Remote Control, insert the supplied

button-type battery.

1 While pressing the Lock Button

1

, pull out

the Battery Holder. Then, remove the

button-type battery.

2 Insert the button-type battery with the (+)

marking facing upward.

3 Insert the Battery Holder into the Remote

Control.

• When the button-type battery is exhausted, replace

it with a new CR2025 battery. (A battery is normally

expected to last about 1 year. However, it depends

on operation frequency.)

• Make sure to match the poles correctly when

inserting the button-type battery.

WARNING

CAUTION

● Replace Battery with Panasonic type

CR2025 only. Use of another battery may

present a risk of ﬁ re or explosion.

● Battery may explode if mistreated.

● As with any small object, this type of Battery

can be swallowed by young children. Do not

allow children to handle this Battery.

● Dispose of used battery promptly.

● Do not recharge, disassemble or dispose of

in ﬁ re.

Using the Remote Control

• Distance from the Camcorder: Within

approximately 15 feet (5 meters)

• Angle: Within approximately 15° in the vertical and

horizontal directions from the central axis

1 Direct the Remote Control at the Remote

Control Sensor

31

of the Camcorder and

press an appropriate button.

[VCR1]:

Press the [ ] Button and [ ] Button

simultaneously.

1

[VCR2]:

Press the [ ] Button and [ ] Button

simultaneously.

2

• When the battery in the Remote Control is replaced,

the mode is automatically reset to [VCR1] Mode.

• The above operating ranges are for indoor use

Outdoors or under strong light, the Camcorder may

not operate properly even within the above ranges.

Selecting Remote Control Modes

When 2 Camcorders are used simultaneously, they

can be operated individually by selecting different

Remote Control Modes.

• If the Remote Control Mode of the Camcorder and

that of the Remote Control do not match, [CHECK

REMOTE MODE (REMOTE)] Indication is displayed.

Setup on the Camcorder:

Set [REMOTE] on the [INITIAL] Sub-Menu to the

desired Remote Control Mode. (p. 21)

Setup on the Remote Control:

15°

12

31

1

16

Before Use

Using the Battery

Before use, fully charge the Battery.

• Since the Battery will not be charged when the DC

Cable is connected to the AC Adaptor, disconnect

it from the AC Adaptor.

• The [POWER] Lamp and [CHARGE] Lamp light

up, and charging starts.

• When the [CHARGE] Lamp goes off, charging is

completed.

• When the battery is completely discharged, the

[CHARGE] Lamp blinks at ﬁ rst, but the battery is

charged normally. When the temperature of the

battery is too high or low, the [CHARGE] Lamp

blinks and the charging time becomes longer than

usual.

• We recommend using a Panasonic Battery.

• We cannot guarantee the quality of this Camcorder

when batteries from other companies are used.

1 Attach the Battery to the AC Adaptor and

charge it.

• For other notes concerning this item, see page 61.

Disconnecting the Power Source

Set the [OFF/ON] Switch

44

to [OFF], and while

sliding the [BATTERY RELEASE] Switch

48

,

remove the Battery downward or DC Cable.

• When attaching or removing Battery, set the [OFF/ON]

Switch to [OFF] and make sure the [POWER] Lamp

is not lit.

Charging Time and Available

Recording Time

CGR-D08R

A

1 h

B

2 h 10 min. (1 h 45 min.)

CGR-D14

A

1 h 30 min.

B

3 h (2 h 25min.)

A

Charging Time

Maximum Continuous Recording Time

B

• “1 h 30 min.” indicates 1 hour and 30 minutes.

• Battery CGR-D08R (PV-GS9/PV-GS13) or

CGR-D14 (PV-GS15) is supplied.

• The times shown in the table are approximate

times. The numbers indicate the recording time

when the Viewﬁ nder is used. The numbers in

parentheses indicate the recording time when the

LCD Monitor is used. In actual use, the available

recording time may be shorter.

• The times shown in the table are for continuous

recording at a temperature of 68 °F (25 °C) and

humidity of 60 %. If the Battery is charged at a

higher or lower temperature, the charging time

may be longer.

• The available recording time becomes shorter

if you use both of Viewﬁ nder and LCD Monitor

simultaneously when rotating the LCD Monitor

forward to record yourself or setting [EVF ON/

AUTO] to [ON].

44

48

2 Attach the charged Battery to the Camcorder.

Power Supply

Using the AC Adaptor

1 Connect the DC Cable to the Camcorder.

2 Connect the DC Cable to the AC Adaptor.

3 Connect the AC Cable to the AC Adaptor and

the AC Jack.

• Before connecting or disconnecting the power

supply, set the [OFF/ON] Switch

44

on the

Camcorder to [OFF] and make sure that

[POWER] Lamp is not lit. (p. 18)

17

Before Use

• When not using the Lens Cap, pull the Lens Cap

Cord in the direction of the arrow.

1

• When you are not recording, be sure to cover the

Lens with the Lens Cap for protection.

2

Re-attaching the Lens Cap

To protect the Lens surface, attach the Lens Cap.

• The Lens Cap and Lens Cap Cord come preattached

to the Grip Belt.

1 Pass one end of the Lens Cap Cord through

the attached eye on the Lens Cap. Then pass

the Lens Cap through the loop made by itself

and pull tight.

Attaching the Shoulder Strap

We recommend that you attach the Shoulder Strap

before going out to avoid dropping the Camcorder.

1 Pull the end of the Shoulder Strap through

the Shoulder Strap Holder on the Camcorder.

2 Fold the end of the Shoulder Strap, run it

through the Shoulder Strap Length Adjuster,

and pull it.

• Pull it out more than 1 inch (2 cm)

1

from the

Shoulder Strap Length Adjuster so that it cannot

slip off.

• Attach the other end of the Shoulder Strap to the

other Shoulder Strap Holder in the same way.

Inserting a Cassette

1 Slide the [OPEN/EJECT] Lever

37

toward the

front and pull down to fully open the Cassette

Compartment Cover.

• To protect the tape, if the cover is not fully opened,

the cassette cannot be ejected.

2 Insert a Cassette.

3 Close the Cassette Holder by pressing the

[PUSH] mark

1

.

4 Close the Cassette Compartment Cover by

pressing the mark

2

.

The Grip Belt

To Use as a Grip Belt

Adjust the length of the Grip Belt to the size of your

hand.

1 Detach the end of the Grip Belt.

2 Adjust the length of the Grip Belt to the size

of your hand.

3 Reattach the Grip Belt.

1

37

2

1

2

• When you remove the Lens Cap, press the knobs

ﬁ rmly.

18

Before Use

Accidental Erasure Prevention

Opening the accidental erasure prevention slider

1

on the cassette (by sliding it to the [SAVE] arrow

direction) prevents recording. To enable recording,

close the accidental erasure prevention slider (by

sliding it to the [REC] arrow direction).

• For other notes concerning this item, see page 61.

While the Camcorder is accessing the Card (reading,

recording, playback or erasing), the Card Access

Lamp lights up.

• While the Card Access Lamp is on, never attempt

to open the Card Slot Cover, to pull out the Card,

to turn off the Camcorder, or to turn the Mode Dial.

Such actions will damage the Card, and recorded

data, and cause the Camcorder to malfunction.

1

Using a Memory Card (For PV-GS13/

PV-GS15)

A Card can be used to record still pictures.

• Use a genuine SD Memory Card or MultiMediaCard

manufactured by Panasonic only.

Before inserting or removing a Card, be sure to

turn off the Camcorder.

• The Camcorder may not function properly or it may

cause the loss of recorded data in a Card.

Inserting a Card

1 Slide the [OPEN] Lever

3

to open the Card

Slot Cover

5

.

2 While holding the Memory Card with its cut

corner facing right

1

, insert it into the Card

Slot

4

.

3 Close the Card Slot Cover

5

securely.

Removing the Card

Open the Card Slot Cover and press the centre of

the Card and then pull it straight out.

• After removing the Card, close the Card Slot Cover.

• The Camcorder may be damaged if the Card is

forced out when the Card is fully inserted.

Card Access Lamp

12

Turning on the Camcorder

Turn on the power ﬁ rst and then select modes.

How to Turn on the Power

1 Set the [OFF/ON] Switch

44

to [ON] while

pressing the button

1

.

• The [POWER] Lamp

41

lights up.

How to Turn off the Power

2 Set the [OFF/ON] Switch

44

to [OFF] while

pressing the button

1

.

Easy to Use Mode Dial

You can choose a desired mode by rotating the Mode

Dial.

1 Rotate the Mode Dial

40

.

3

5

1

4

1

44

41

1

44

40

(PV-GS13/PV-GS15) (PV-GS9)

12

:

Tape Recording Mode

Use this mode when recording pictures on a

tape.

Also, you can record still pictures on the card

simultaneously while recording on a tape (For

PV-GS13/PV-GS15).

:

Tape Playback Mode

Use this mode when playing back the

recorded scene on a tape.

:

Card Recording Mode

(For PV-GS13/PV-GS15)

Use this mode when recording still pictures

on a card.

:

Picture Playback Mode

(For PV-GS13/PV-GS15)

Use this mode when playing back the

recorded still picture on a card.

:

PC Mode

(For PV-GS13/PV-GS15)

Use this mode when you want to connect the

Camcorder to your Personal Computer.

19

Before Use

Using the Viewﬁ nder/ LCD Monitor

Using the Viewﬁ nder

Before using the Viewﬁ nder, adjust the ﬁ eld of view so

that the displays inside the Viewﬁ nder become clear

and easy to read.

1 Pull the Viewﬁ nder.

2 Adjust by turning the Eyepiece Corrector

Knob

35

.

To Use the Viewﬁ nder at the Same Time as the

LCD Monitor

Set [LCD/EVF] >> [EVF ON/AUTO] >> [ON].

• The Viewﬁ nder does not turn off even if the LCD

Monitor is opened.

• When you turn the Camcorder off, this setting is

cancelled.

Using the LCD Monitor

With the LCD Monitor open, you can also record the

picture while watching it.

1 Place your Thumb on the [OPEN▼] Knob

1

and pull the LCD Monitor

2

out in the

direction of the arrow.

• The Viewﬁ nder is now deactivated.

• The LCD Monitor can be opened a maximum

of 120°. If you open the LCD Monitor by 120°, it

becomes convenient to operate menus or to play

back pictures.

2 Adjust the LCD Monitor angle according to

the desired recording angle.

• The LCD Monitor can rotate a maximum of 180°

1

from the vertical position upwards and a

maximum of 90°

2

to the downward direction.

Forcefully rotating the LCD Monitor beyond these

ranges will damage the Camcorder.

Closing the LCD Monitor

Push the LCD Monitor until it is securely locked.

• Make sure the Card Slot Cover is closed.

Adjusting Brightness and Colour Level

When [LCD/EVF SET] on the [LCD/EVF] Sub-Menu

is set to [YES], the following items are displayed.

LCD Brightness [LCD BRIGHTNESS]

Adjusts the brightness of the image on the LCD

screen.

LCD Colour Level [LCD COLOR LEVEL]

Adjusts the colour saturation of the image on the LCD

screen.

Brightness of the Viewﬁ nder

[EVF BRIGHTNESS]

Adjusts the brightness of the image in the Viewﬁ nder.

To Adjust

Press the [ / ] Button and select the item to be

adjusted, and then press the [ / ] Button to

raise or lower the number of vertical bars in the Bar

Indication.

• More vertical bars indicates stronger brightness or

colour saturation.

35

2

1

180°

2

90°

• For other notes concerning this item, see page 68.

Using the Menu Screen

To facilitate the selection of a desired function or

setup, this Camcorder displays various function setups

on Menus.

• When operating the menu with the Viewﬁ nder, set

[LCD/EVF] >> [EVF ON/AUTO] >> [ON] or rotate the

LCD Monitor by 180°.

1 Press the [MENU] Button

19

.

19

14 1513 16 17

20

Before Use

1) [CAMERA]

Camera Setup Sub-Menu

[PROG.AE]

Auto Exposure Mode (p. 30)

[EIS]

Image Stabilizer (p. 28)

[D.ZOOM]

Digital Zoom (p. 27)

[SHTR EFFECT] (PV-GS9 Only)

Shutter effect (p. 25)

[SELF TIMER]

Self-timer Recording (p. 27)

[USB FUNCTION]

USB Functions Mode (pp. 51, 54)

• If you press the [ ] Button, the menu changes

back to the previous screen.

2) [DIGITAL]

Digital Setup Sub-Menu

[EFFECT1]

Digital Effects 1 (p. 33)

[EFFECT2]

Digital Effects 2 (p. 33)

[MULTI MODE]

Multi-Picture Mode (p. 33)

[TITLE IN] (For PV-GS13/PV-GS15)

Adding a Title (p. 40)

3) [CARD] (For PV-GS13/PV-GS15)

Card Setup Sub-Menu

[PICT QUALITY]

Picture Quality (p. 25)

[CREATE TITLE]

Title Creation (p. 40)

4) [RECORDING]

Recording Setup Sub-Menu

[REC SPEED]

Recording Speed Mode (p. 23)

2 Press the [ / ] Button

13

16

to select a

desired Sub-Menu.

• Press the [ / ] Button to display the highlighted

item.

3 Press the [ ] Button

14

to display the

selected Sub-Menu.

4 Press the [

/ ] Button to select the item.

5 Press the [

] Button

14

to display the

selected item.

6 Press the [

/ ] to select the desired mode

and press the [ENTER]

15

Button to

determine the setting.

• While a Menu is displayed, you cannot record or play

back. Menus can be displayed during playback but

not during recording. The above operations can be

done using the [MENU] Button, [▲▼◄►] Buttons

and [ENTER] Button on the Remote Control. (p. 14)

To Return to the Previous Screen

Press the [

] Button

17

.

To Exit the Menu Screen

Press the [MENU] Button again.

About the Menu Mode Setting

The setting selected on the Menu will be retained

even when the Camcorder is turned off. However,

if the Battery or AC Adaptor is disconnected before

turning off the Camcorder, the selected setup may

not be retained.

• Menu operation ﬂ ow is shown in this text by >>.

File Selection in the Picture Playback

Mode (For PV-GS13/PV-GS15)

A File Selection Operation may be necessary during

Menu Operations. In this case, carry out the following

procedure.

2 Press the [ENTER] Button

15

to conﬁ rm the

selection of the ﬁ le.

• After the above File Selection Procedure, carry

out the various Menu Operations. (The above

procedure will not be repeated in the following

instructions.)

List of Menus

The ﬁ gures of the Menus are for explanation purposes

only, and they are different from the actual Menus.

[TAPE RECORDING MENU]

Tape Recording Menu

(PV-GS13/PV-GS15)

(PV-GS9)

• The Menu corresponding to the Mode selected by

using the Mode Dial

40

is displayed.

(PV-GS13/

PV-GS15)

(PV-GS9)

40

1 Press the [ / / / ] Button and select

a ﬁ le.

• The selected ﬁ le is marked by a frame.

La page charge ...

Panasonic PVGS9 Mode d'emploi

Ce manuel convient également à

Panasonic PVGS9 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents