Powercast TX91503 Manuel utilisateur

TX91503
Marque
Powercast
Modèle
TX91503
Taper
Manuel utilisateur
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Powercast products and technology are covered by one or more patents with other patents pending. All patent and trademark information
can be found at http://www.powercastco.com/IP/.
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 1
www.powercastco.com
PRODUCT DESCRIPTION
The Powercast TX91503 PowerSpot® RF
Wireless Power transmitter is specially
designed to provide both power and data to
end devices containing Powercast’s power
harvesting technology. The PowerSpot
transmitter contains a receiver that can
hear when a Powercast-enabled harvesting
device is in range, allowing it to stop power
transmission when no harvesting devices
are around. The transmitter can also be
controlled by the PowerSpot app that can
control periods of use. The PowerSpot
transmitter is housed in a durable plastic
case with several mounting options.
Operational power is provided to the DC
power connector, and there is a status LED
to provide feedback on the transmitter’s
functional state. This device has a factory
set, fixed power output of 3W EIRP.
FEATURES
• FCC and IC approved
• Flexible wall mounting options
• Transmits power and data
• Wide temperature range
PRODUCT CONTENTS
The following items are included:
Qty
Description
1
915 MHz PowerSpot transmitter
1
Power supply
1
Quick Start instruction card
POWERING APPLICATIONS
• Wireless battery charging
-Headphones
-Headsets
-Game Controllers
-Keyboards and Mice
-Fitness Trackers
-Smart Watches
-Wearables
-Smart Cards
ORDERING OPTIONS
United States Part Number
TX91503
Canada Part Number
TX91503-CA
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 2
www.powercastco.com
SET-UP AND OPERATION
1. Mount the PowerSpot Transmitter at the back of a desk, counter or other area where
you store your devices when not in use to create a PowerSpot recharging zone.
Keyholes are also available on the rear of the transmitter case for wall mounted
applications.
2. Plug the DC connector of the power supply into the connector on the side of the
transmitter. Plug the power supply into a standard 120V outlet.
3. The PowerSpot transmitter will remain off until one of the following occurs:
a. An authorized device enters the PowerSpot recharging zone1.
b. The button on the unit is pressed to recharge a device with a completely
discharged battery. The unit will activate and transmit power for 30 minutes
from a button press and then will turn off if an authorized device is not present.
4. When the PowerSpot transmitter is active and transmitting radio frequency (RF) energy,
data is automatically included in the transmission and can be received and used to
authorize the receiving device.
The status LED indicates the following operating conditions:
LED
Status
Description
Off
Off
5VDC is not applied
Solid Green
Active
Transmitting normally
Solid Red
Idle
PowerSpot is powered but not actively transmitting
Red with short
Green Blinks
Active /
Idle
An authorized device is requesting charge but is not in range of the
PowerSpot
Red and Green
Rapid Blinking
Startup or
Fault
PowerSpot has just been powered on, or if already powered on is in a
fault condition such as overheating
Red with long
Green Blinks
Idle due to
snooze
PowerSpot is powered but not actively transmitting due to the
snooze set by the PowerSpot app
1The PowerSpot app can override these conditions and keep the transmitter in an OFF state using the “Snooze” feature.
SNOOZE SETTING AND FIRMWARE UPDATES
Snooze setting for the PowerSpot transmitter:
1. Setting a Snooze time allows the user to set up to four time periods where the
transmitter will remain OFF, even if a device within range requests a charge
2. Using the PowerSpot app, navigate to the Snooze tab
3. Enter the transmitter ID found on the back label of your transmitter
4. Select the “+” button to add events
5. Choose a start and end time for your event(s)
6. After adding desired events, hit “Set Snooze”
7. The app will report that the Snooze has been set successfully or not
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 3
www.powercastco.com
Note: The PowerSpot transmitter will not transmit the RF energy that is used for power
and data as described above while the Snooze is being set.
Note: When setting the Snooze, the transmitter’s time is automatically synced with the
time of the mobile phone.
Note: If power is disconnected from the PowerSpot transmitter, any previously set
Snooze will be deleted.
Time re-syncing for the PowerSpot transmitter:
1. To re-sync the PowerSpot transmitter’s time with the mobile phone, navigate to the
“Snooze” tab in the PowerSpot app
2. Enter the transmitter’s ID and hit “Sync Time”
3. The app will report that the time has been set successfully or not
If a firmware upgrade is available for the PowerSpot transmitter:
1. Unplug the power to the PowerSpot transmitter
2. Press and hold the top button down
3. With the button still pressed, plug the transmitter back in. Once powered on, the LED
will be solid green and you can let go of the button
4. Within 2 minutes, navigate to the “Scan Devices” tab of the PowerSpot app.
“PowerSpot” with a download icon should be available. Tap the download icon and then
“Upgrade” to begin the firmware update.
5. Once the upgrade is complete, the app will report “Done”.
Note: If the PowerSpot transmitter is not connected to the app within 2 minutes, it will
automatically return to normal operation.
Note: The transmitter will not transmit the RF energy that is used for power and data as
described above during a firmware upgrade.
To determine the current firmware version of your transmitter:
1. Press and hold the button on the top of the PowerSpot transmitter for at least 5
seconds
2. Continue holding the button and utilize the “PowerSpot” app on the “Scan Devices” tab
to determine the firmware version
Note: The PowerSpot transmitter will stop communicating the firmware version and
return to normal operation when the button is released.
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 4
www.powercastco.com
SPECIFICATIONS
Item
Frequency
Data
Power output
Beam pattern
Approvals
Data Communications
Operating Temperature
Environment
Mounting
Power
Color
Dimensions
Firmware Upgrade
Communication
MECHANICAL (REAR VIEW)
*Dimensions in inches
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 5
www.powercastco.com
SUPPORT
Technical support for Powercast products can be initiated through the following methods:
Website contact form: http://www.powercastco.com/contact/
Telephone: +1 412-455-5800
COMPLIANCE STATEMENTS
Changes or modifications not expressly approved by Powercast could void the user’s authority
to operate the equipment. Use and maintain device only as specified in this manual.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 6
www.powercastco.com
WARNING!
FCC Radiation Exposure Statement:
This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled
environment under the following conditions:
1. This equipment should be installed and operated such that a minimum separation distance of
20cm is maintained between the radiator (antenna) & user’s/nearby person’s body at all times.
2. This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
IC Radiation Exposure Statement:
This equipment complies with IC’s RF radiation exposure limits set forth for an uncontrolled
environment under the following conditions:
1. This equipment should be installed and operated such that a minimum separation distance of
30cm is maintained between the radiator (antenna) & user’s/nearby person’s body at all times.
2. This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet équipement est conforme aux limites d'exposition aux rayonnements RF d'IC établies pour
un environnement non contrôlé dans les conditions suivantes:
1. Cet équipement doit être installé et utilisé de manière à ce qu'une distance de séparation
minimale de 30 cm soit maintenue à tout moment entre le radiateur (antenne) et le corps de
l'utilisateur / de la personne proche.
2. Cet émetteur ne doit pas être situé à proximité ou fonctionner en conjonction avec toute
autre antenne ou émetteur.
User Manual
TX91503 – 915 MHz PowerSpot Transmitter
Rev 12.0 – 2022/10 User’s Manual - TX91503 Transmitter Page 7
www.powercastco.com
IMPORTANT NOTICE
Information furnished by Powercast Corporation (Powercast) is believed to be accurate and
reliable. No license, express or implied, to any intellectual property rights is granted by this
document. No responsibility is assumed by Powercast for its use, nor for any infringements of
patents or other rights of third parties that may result from its use. Powercast assumes no
liability for misuse of this product. Specifications are subject to change without notice.
No license is granted by implication or otherwise under any patent or patent rights of
Powercast. Trademarks and registered trademarks are the property of their respective owners.
Powercast’s standard Terms and Conditions and Limited Product Warranty are available at:
https://www.powercastco.com/terms-conditions/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Powercast TX91503 Manuel utilisateur

TX91503
Marque
Powercast
Modèle
TX91503
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents