DeWalt DWS716 12 Inch (305 mm) Double Bevel Compound Miter Saw Manuel utilisateur

Marque: DeWalt

Modèle: DWS716 12 Inch (305 mm) Double Bevel Compound Miter Saw

Catégorie: Scies à onglet

Taper: Manuel utilisateur

Ce manuel convient également à

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

Final Page Size: 8.5 x 11in

DWS716, DWS716XPS

12" (305 mm) Double Bevel Compound Miter Saw

Scie à onglets combinée à biseau double 305 mm (12po)

Sierra de Inglete Compuesta de Doble Bisel de 305 mm (12")

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 14

Español (traducido de las instrucciones originales) 28

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.

Fig. A

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or any

DeWALT tool, call us toll free at:

1-800-4-DeWALT (1-800-433-9258).

1 Trigger switch

2 Operating handle

3 Mounting holes

4 Lower guard

5 Miter lock lever

6 Miter detent trigger

7 Miter scale

8 Miter scale screws

9 Hand indentations

10 Sliding fence

11 Bevel lock knob

12 Dust port

13 Carrying handle

14 Fence lock knob

15 Clamp mounting hole

16 6 mm hex wrench

17 Head lock pin

18 Base fence

19 45° bevel stop adjustment screw

20 45° bevel stop override levers

21 Vertical material clamp

22 Miter detent override

23 CUTLINE LED On/Off switch

(DWS716XPS only)

567

DWS716XPS

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all instructions listed below may result in

electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-

operated (cordless) powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark areas inviteaccidents.

b ) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust

orfumes.

c ) Keep children and bystanders away while operating a power tool. Distractions can

cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

orgrounded.

c ) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electricshock.

e ) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personalinjury.

b ) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invitesaccidents.

d ) Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personalinjury.

e ) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in

movingparts.

g ) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

relatedhazards.

h ) Do not let familiarity gained from frequent use of tools allow you to become

complacent and ignore tool safety principles. A careless action can cause severe injury

within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power tool for your application. The

correct power tool will do the job better and safer at the rate for which it wasdesigned.

b ) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are

caused by poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardoussituations.

h ) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpectedsituations.

5) Service

a ) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool ismaintained.

Safety Instructions for Miter Saws

a ) Miter saws are intended to cut wood or wood-like products, they cannot be used

with abrasive cut-off wheels for cutting ferrous material such as bars, rods, studs,

etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive

cutting will burn the lower guard, the kerf insert and other plasticparts.

b ) Use clamps to support the workpiece whenever possible. If supporting the

workpiece by hand, you must always keep your hand at least 100 mm from either

side of the saw blade. Do not use this saw to cut pieces that are too small to be

securely clamped or held by hand. If your hand is placed too close to the saw blade, there

is an increased risk of injury from bladecontact.

c ) The workpiece must be stationary and clamped or held against both the fence and

the table. Do not feed the workpiece into the blade or cut “freehand” in any way.

Unrestrained or moving workpieces could be thrown at high speeds, causinginjury.

d ) Never cross your hand over the intended line of cutting either in front or behind the

saw blade. Supporting the workpiece “cross handed” i.e. holding the workpiece to the right

of the saw blade with your left hand or vice versa is verydangerous.

e ) Do not reach behind the fence with either hand closer than 100 mm from either side

of the saw blade, to remove wood scraps, or for any other reason while the blade

is spinning. The proximity of the spinning saw blade to your hand may not be obvious and

you may be seriouslyinjured.

f ) Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp

it with the outside bowed face toward the fence. Always make certain that there

is no gap between the workpiece, fence and table along the line of the cut. Bent or

warped workpieces can twist or shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or foreign objects in theworkpiece.

g ) Do not use the saw until the table is clear of all tools, wood scraps, etc., except

for the workpiece. Small debris or loose pieces of wood or other objects that contact the

revolving blade can be thrown with highspeed.

h ) Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately

clamped or braced and may bind on the blade or shift duringcutting.

i ) Ensure the miter saw is mounted or placed on a level, firm work surface before use.

A level and firm work surface reduces the risk of the miter saw becomingunstable.

j ) Plan your work. Every time you change the bevel or miter angle setting, make sure

the fence will not interfere with the blade or the guarding system. Without turning

the tool “ON” and with no workpiece on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or danger of cutting thefence.

k ) Provide adequate support such as table extensions, saw horses, etc. for a workpiece

that is wider or longer than the table top. Workpieces longer or wider than the miter

saw table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the

lower guard or be thrown by the spinningblade.

l ) Do not use another person as a substitute for a table extension or as additional

support. Unstable support for the workpiece can cause the blade to bind or the workpiece to

shift during the cutting operation pulling you and the helper into the spinningblade.

m ) The cut-off piece must not be jammed or pressed by any means against the

spinning saw blade. If confined, i.e. using length stops, the cut-off piece could get wedged

against the blade and thrownviolently.

n ) Always use a clamp or a fixture designed to properly support round material such

as rods or tubing. Rods have a tendency to roll while being cut, causing the blade to “bite”

and pull the work with your hand into theblade.

o ) Let the blade reach full speed before contacting the workpiece. This will reduce the risk

of the workpiece beingthrown.

p ) If the workpiece or blade becomes jammed, turn the miter saw off. Wait for all

moving parts to stop and disconnect the plug from the power source and/or remove

the battery pack. Then work to free the jammed material. Continued sawing with a

jammed workpiece could cause loss of control or damage to the mitersaw.

q ) After finishing the cut, release the switch, hold the saw head down and wait for

the blade to stop before removing the cut-off piece. Reaching with your hand near the

coasting blade isdangerous.

r ) Hold the handle firmly when making an incomplete cut or when releasing the

switch before the saw head is completely in the down position. The braking action of

the saw may cause the saw head to be suddenly pulled downward, causing a risk ofinjury.

ENGLISH

Additional Safety Rules for Miter Saws

WARNING: Do not allow familiarity (gained from frequent use of your saw) to replace

safety rules. Always remember that a careless fraction of a second is sufficient to inflict

severeinjury.

WARNING: Never modify the power tool or any part of it. Damage or personal injury

couldresult.

• DO NOT OPERATE THIS MACHINE until it is completely assembled and installed according to

the instructions. A machine incorrectly assembled can cause seriousinjury.

• OBTAIN ADVICE from your supervisor, instructor, or another qualified person if you are not

thoroughly familiar with the operation of this machine. Knowledge issafety.

• FOLLOW ALL WIRING CODES and recommended electrical connections to prevent shock

or electrocution. Protect electric supply line with at least a 15 ampere time-delay fuse or a

circuitbreaker.

• MAKE CERTAIN the blade rotates in the correct direction. The teeth on the blade should point in

the direction of rotation as marked on thesaw.

• TIGHTEN ALL CLAMP HANDLES, knobs and levers prior to operation. Loose clamps can cause

parts or the workpiece to be thrown at highspeeds.

• BE SURE all blade and blade clamps are clean, recessed sides of blade clamps are against blade

and arbor screw is tightened securely. Loose or improper blade clamping may result in damage

to the saw and possible personalinjury.

• DO NOT OPERATE ON ANYTHING OTHER THAN THE DESIGNATED VOLTAGE for the saw.

Overheating, damage to the tool and personal injury mayoccur.

• DO NOT WEDGE ANYTHING AGAINST THE FAN to hold the motor shaft. Damage to tool and

possible personal injury mayoccur.

• NEVER CUT FERROUS METALS or masonry. Either of these can cause the carbide tips to fly off

the blade at high speeds causing seriousinjury.

• NEVER PLACE HANDS CLOSER THAN 4" (100 mm) FROM THEBLADE.

• NEVER HAVE ANY PART OF YOUR BODY IN LINE WITH THE PATH OF THE SAW BLADE.

Personal injury willoccur.

• NEVER APPLY BLADE LUBRICANT TO A RUNNING BLADE. Applying lubricant could cause

your hand to move into the blade resulting in seriousinjury.

• DO NOT place either hand in the blade area when the saw is connected to the power source.

Inadvertent blade activation may result in seriousinjury.

• NEVER REACH AROUND OR BEHIND THE SAW BLADE. A blade can cause seriousinjury.

• DO NOT REACH UNDERNEATH THE SAW unless it is unplugged and turned off. Contact with

saw blade may cause personalinjury.

• SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Vibration can possibly cause

the machine to slide, walk, or tip over, causing seriousinjury.

• USE ONLY CROSSCUT SAW BLADES recommended for miter saws. For best results, do not

use carbide tipped blades with hook angles in excess of 7 degrees. Do not use blades with deep

gullets. These can deflect and contact the guard, and can cause damage to the machine and/or

seriousinjury.

• USE ONLY BLADES OF THE CORRECT SIZE AND TYPE specified for this tool to prevent

damage to the machine and/or seriousinjury.

• INSPECT BLADE FOR CRACKS or other damage prior to operation. A cracked or damaged

blade can come apart and pieces can be thrown at high speeds, causing serious injury. Replace

cracked or damaged bladesimmediately.

• CLEAN THE BLADE AND BLADE CLAMPS prior to operation. Cleaning the blade and blade

clamps allows you to check for any damage to the blade or blade clamps. A cracked or damaged

blade or blade clamp can come apart and pieces can be thrown at high speeds, causing

seriousinjury.

• DO NOT USE WARPED BLADES. Check to see if the blade runs true and is free from vibration. A

vibrating blade can cause damage to the machine and/or seriousinjury.

• DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic

guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.

• KEEP GUARD IN PLACE and in workingorder.

• ALWAYS USE THE KERF PLATE AND REPLACE THIS PLATE WHEN DAMAGED. Small chip

accumulation under the saw may interfere with the saw blade or may cause instability of

workpiece whencutting.

• USE ONLY BLADE CLAMPS SPECIFIED FOR THIS TOOL to prevent damage to the machine

and/or seriousinjury.

• CLEAN THE MOTOR AIR SLOTS of chips and sawdust. Clogged motor air slots can cause the

machine to overheat, damaging the machine and possibly causing a short which could cause

seriousinjury.

• NEVER LOCK THE SWITCH IN THE “ON” POSITION. Severe personal injury mayresult.

• NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is

unintentionallycontacted.

• ADDITIONAL INFORMATION regarding the safe and proper operation of power tools (i.e., a

safety video) is available from the Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH

44115-2851 (www.powertoolinstitute.com). Information is also available from the National

Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American

National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the

U.S. Department of Labor OSHA 1910.213Regulations.

WARNING: Cutting plastics, sap coated wood, and other materials may cause melted

material to accumulate on the blade tips and the body of the saw blade, increasing the risk

of blade overheating and binding whilecutting.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.

Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED

SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treatedlumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmfulchemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious

and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory

protection appropriate for the dust exposure. Direct particles away from face andbody.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this

product may contribute to hearingloss.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long

hair can be caught in movingparts.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is,

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

The label on your tool may include the following symbols. The symbols and their definitions are

asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction (grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per minute

sfpm ................... surface feet per minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or direct current

...................... Class II Construction (double insulated)

no .......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory protection

..................... wear eye protection

..................... wear hearing protection

..................... read all documentation

ENGLISH

For your convenience and safety, the following warning labels are on your mitersaw.

ON GUARD:

DANGER–KEEP AWAY FROM BLADE.

ON UPPER GUARD:

PROPERLY SECURE BRACKET WITH BOTH SCREWS BEFOREUSE.

ON TABLE: (2 PLACES)

WARNING: KEEP HANDS AND BODY OUT OF THE PATH OF THE

SAW BLADE. CONTACT WITH BLADE WILL RESULT IN SERIOUS

INJURY. DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.

CHECK GUARDING SYSTEM TO MAKE SURE IT IS FUNCTIONING

CORRECTLY. DO NOT PERFORM ANY OPERATION FREEHAND.

NEVER REACH IN BACK OF SAW BLADE TURN OFF TOOL

AND WAIT FOR SAW BLADE TO STOP BEFORE MOVING WORKPIECE OR CHANGING

SETTINGS OR MOVING HANDS. NEVER CROSS ARMS IN FRONT OF BLADE. ALWAYS

TIGHTEN ADJUSTMENT KNOBS BEFORE EACH USE. DISCONNECT POWER BEFORE

CHANGING BLADE ORSERVICING.

ON TABLE: (2 PLACES)

Electrical Connection

Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that your

saw will operate on alternating current only. A voltage decrease of 10 percent or more will cause

a loss of power and overheating. All DeWALT tools are factory tested. If this tool does not operate,

check the powersupply.

Specifications

Capacity of cut

50° miter left and right

48º bevel left and right

0° miter

Max. Height 3.6" (91.5 mm) Resulting Width 7.2" (183 mm)

Max. Width 7.9" (200.7 mm) Resulting Height 2.9" (73.7mm)

45° miter

Max. Height 3.6" (91.5 mm) Resulting Width 4.9" (125 mm)

Max. Width 5.5" (140 mm) Resulting Height 2.9" (73.7 mm)

45° bevel - Left

Max. Height 2.3" (58.4 mm) Resulting Width 7.4" (188 mm)

Max. Width 1.6" (40.6 mm) Resulting Height 7.1" (180.3 mm)

45º bevel - Right

Max. Width 7.9" (200.7 mm) Resulting Height 1.1" (28 mm)

Max. Height 1.6" (40.6 mm) Resulting Width 7.1" (180.3 mm)

Your saw is capable of cutting baseboard moldings 0.75" (19mm) thick by 6.5" (165mm) tall

on a 45° right or leftmiter.

Drive

120 Volt motor

15 Amp motor

3800 RPM

Cut helical gears with roller and ball bearings

Carbide tooth blade

Automatic electric brake

Unpacking Your Saw

Check the contents of your miter saw carton to make sure that you have received all parts. In

addition to this instruction manual, the carton should contain:

1 DWS716 miter saw with carbide tipped blade

1 6 mm hex wrench

1 Dust bag

1 Vertical material clamp

1 Instruction manual

COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part of it. Damage or personal injury

couldresult.

Refer to Figure A at the beginning of this manual for a complete list ofcomponents.

Intended Use

This heavy duty miter saw is designed for professional wood cuttingapplications.

DO NOT use under wet conditions or in presence of flammable liquids orgases.

This miter saw is a professional power tool. DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use thistool.

Familiarization (Fig. A, B)

Your miter saw is fully assembled in the carton.Open the box and lift the saw out by the

convenient carrying handle 13 , as shown in FigureB.

Place the saw on a smooth, flat surface such as a workbench or strongtable.

Examine Figure A to become familiar with the saw and its various parts. The section on

adjustments will refer to these terms and you must know what and where the partsare.

CAUTION: Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle

when pulling the handle down. The lower guard will move up as the handle is pulled down

which could cause pinching.The handle is placed close to the guard for specialcuts.

Press down lightly on the operating handle 2 and pull head lock pin 17 . Gently release the

downward pressure and hold the arm allowing it to rise to its full height. Use the lock down

pin when carrying the saw from one place to another. To lock the arm, rotate head lock knob

a quarter turn and press down on the arm until the arm locks in place. Always use the carrying

handle 13 to transport the saw or the hand indentations 9 shown in FigureA.

Fig. B

Bench Mounting (Fig. A)

Mounting holes 3 are provided in all four feet to facilitate bench mounting, as shown in FigureA.

There are round countersunk holes for use with screws and square holes for use with the miter

saw stand "carraige bolt" or M8 (5/16") or smaller bolts. Use either hole, it is not necessary to use

both.) Always mount your saw firmly to prevent movement. To enhance the tool’s portability, it

can be mounted to a piece of 1/2" (12.7 mm) or thicker plywood which can then be clamped to

your work support or moved to other job sites andreclamped.

NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting

screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work

support. When clamping the saw to any work surface, clamp only on the clamping bosses where

the mounting screw holes are located. Clamping at any other point will surely interfere with the

proper operation of thesaw.

CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not warped

or otherwise uneven. If the saw rocks on the surface place a thin piece of material under one

saw foot until the saw sits firmly on the mountingsurface.

Transporting the Saw (Fig. A)

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make anyadjustments.

WARNING: To reduce the risk of serious personal injury, ALWAYS lock the miter lock lever 5,

bevel lock knob 11 , head lock pin 17 , and fence lock knob 14 before transportingsaw.

WARNING: The miter lock knob should be used only when carrying or storing the saw.

NEVER use the lock knob for any cuttingoperation.

In order to conveniently carry the miter saw from place to place, a carrying handle 13 has been

included on the top of the saw arm and hand indentations 9 in the base, as shown in FigureA.

To transport the saw, lower the arm of the saw and press in the head lock pin 17 to secure the

arm. It will snap into the lock position.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect

it from power source before making any adjustments or removing/installing

attachments or accessories. An accidental start-up can causeinjury.

NOTE: Your miter saw is fully and accurately adjusted at the factory at the time of manufacture.

If readjustment due to shipping and handling or any other reason is required, follow the steps

below to adjust yoursaw.

Once made, these adjustments should remain accurate. Take a little time now to follow these

directions carefully to maintain the accuracy of which your saw iscapable.

Changing or Installing a New Saw Blade (Fig. A, C–E)

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make anyadjustments.

ENGLISH

CAUTION:

• Never depress the spindle lock button while the blade is under power orcoasting.

• Do not cut ferrous metal (containing iron or steel) or masonry or fiber cement product

with this mitersaw.

Removing the Blade

1. Unplug thesaw.

2. Raise the arm to the upper position and raise the lower guard 4 as far aspossible.

3. Loosen, but do not remove guard bracket screw 39 until the bracket can be raised far

enough to access the blade screw 34 . Lower guard will remain raised due to the position of

the guard bracketscrew.

4. Depress the spindle lock button 24 while carefully rotating the saw blade by hand until the

lockengages.

5. Keeping the button depressed, use the other hand and the 6mm hex wrench 16 provided

to loosen the blade screw. (Turn clockwise, left-hand threads.)

Fig. C

Fig. D

6. Remove the blade screw 34, outer blade clamp 25, and blade 26. The inner blade

clamp27, and if used, the 1" (25.4 mm) blade adapter, may be left on thespindle.

NOTE: For blades with a blade hole of 5/8" (15.88 mm), the 1" (25.4 mm) blade adapter 40

is notused.

Fig. E

25 26

Installing a Blade

1. Unplug thesaw.

2. With the arm raised, the lower guard held open and the guard bracket, place the blade on

the spindle, onto the blade adapter [if using a blade with a 1" (25.4 mm) diameter blade hole]

and against the inner blade clamp with the teeth at the bottom of the blade pointing toward

the back of thesaw.

3. Assemble the outer blade clamp onto thespindle.

4. Install the blade screw 34 and, engaging the spindle lock, tighten the screw firmly with the

6mm hex wrench provided. (Turn counterclockwise, left-hand threads.)

NOTE: When using blades with a 5/8" (15.88 mm) diameter blade hole, the blade adapter will

not be used and should be stored in a safe place for futureuse.

5. Return the guard bracket to its original position and firmly tighten the guard bracket

screw39 to hold bracket inplace.

WARNING:

• The guard bracket must be returned to its original position and the screw

tightened before activating thesaw.

• Failure to do so may allow the guard to contact the spinning saw blade resulting

in damage to the saw and severe personalinjury.

Miter Scale Adjustment (Fig. A, F)

Place a square against the saw’s fence and blade. (Do not touch the tips of the blade teeth with

the square. To do so will cause an inaccurate measurement.) Unlock miter lock lever 5 and swing

the miter arm until the miter detent locks it at the 0˚ miter position. Do not lock miter lock lever.

If the saw blade is not exactly perpendicular to the base fence 18 , loosen the three miter scale

screws 8 that hold the miter scale 7 to the base and move the scale/miter arm assembly left or

right until the blade is perpendicular to the fence, as measured with the square. Retighten the

three screws. Pay no attention to the reading of the miter pointer at thispoint.

Fig. F

Miter Pointer Adjustment (Fig. F, G)

Unlock miter lock lever 5 and squeeze the miter detent trigger 6 to move the miter arm to

the zero position. Unlock the miter lock lever to allow the miter detent to snap into place as

you rotate the miter arm toward zero. Observe the pointer 28 and miter scale 7 through the

viewing opening shown in FigureG. If the pointer does not indicate exactly zero, loosen the

pointer screw, adjust the pointer to 0˚ andretighten.

Fig. G

Bevel Square to Table (Fig. A, H)

To align the blade square to the rotary table, lock the arm in the down position. Place a square

against the blade taking care to not have the square on top of a tooth. Loosen the bevel lock

lever 5 and ensure the arm is firmly against the 0° bevel stop. Move the 0° bevel stop adjusting

screw 32 as necessary so that the blade is at 0° bevel to the table. Ensure the bevel override

levers are pushed inward to obtain an accurateadjustment.

ENGLISH

Fig. H

Bevel Pointer (Fig. I)

If the bevel pointer 29 does not indicate zero, loosen the screw 30 that holds it in place and

move the pointer as necessary. Do not remove the steel plate in front of the bevel pointer. This

plate prevents wood resin from accumulating on the bevel scale duringuse.

Fig. I

Adjusting the Bevel Stop to 45° Left or Right (Fig. J)

NOTE: Adjust the 45° bevel angles only after performing the 0° bevel angle and pointer

adjustment. Ensure the 45° bevel override levers 20 are pushed inward to obtain an

accurateadjustment.

To adjust the right 45° bevel angle, loosen the bevel lock knob 11 and pull the bevel stop

override knob 31 to override the 0° bevel stop. When the saw is fully to the right, if the pointer

does not indicate exactly 45°, turn the right bevel stop screw 19 until the pointer indicates 45°.

To adjust the left 45° bevel stop, first loosen the bevel lock knob 11 and tilt the head to the

left. If the pointer does not indicate exactly 45°, turn the left bevel stop screw until the pointer

reads45°.

Fig. J

Adjusting the Bevel Stop to 22.5° (or 33.9° and 30°) (Fig. A, J)

NOTE: Adjust the bevel angles only after performing the 0° bevel angle and bevel

pointeradjustment.

• To set the left 22.5° bevel angle, flip out the left 22.5° bevel pawl 41 . Loosen the bevel lock

knob 11 and tilt the head fully to the left. If the bevel pointer does not indicate exactly 22.5°,

turn the crown adjustment screw 43 contacting the pawl with a 7/16” (10 mm) wrench until

the bevel pointer reads 22.5°.

• To adjust the right 22.5° bevel angle, flip out the right 22.5° bevel pawl. Loosen the bevel

lock knob and pull the 0° bevel stop to override the 0° bevel stop. When the saw is fully to

the right, if the bevel pointer does not indicate exactly 22.5°, turn the crown adjustment

screw contacting the pawl with a 7/16” (10 mm) wrench until the bevel pointer indicates

exactly22.5°.

• To set the 33.9° bevel angle, flip out the stop pawls 41 42 . Loosen the bevel lock knob11

and tilt the head to the left. If the pointer does not indicate exactly 33.9°, turn the screw

contacting the pawl until the pointer reads 33.9°.

• To adjust the right 33.9° bevel angle, flip out the stop pawl. Loosen the bevel lock knob 11

and pull the bevel stop override button 31 to override the 0° bevel stop. When the saw is

fully to the right, if the pointer does not indicate exactly 33.9°, turn the screw contacting the

pawl until the pointer indicates 33.9°.

Fence Adjustment (Fig. K)

In order that the saw can bevel to a full 48° left, the fences can be adjusted to provide clearance.

To adjust a fence, loosen the fence lock knob 14, and slide the fence outward. Make a dry run

with the saw turned off and check for clearance. Adjust the fence to be as close to the blade as

practical to provide max imum workpiece support, without interfering with arm up and down

movement. Tighten knob securely. When the bevel operations are complete, don’t forget to

relocate thefence.

NOTE: The guide groove of the fences can become clogged with sawdust. If the guide groove

becomes clogged, use a stick, low pressure air or a vacuum toclear.

Fig. K

Automatic Electric Brake

Your saw is equipped with an automatic electric blade brake which stops the saw blade within

5seconds of trigger release. This is notadjustable.

On occasion, there may be a delay after trigger release to brake engagement. On rare occasions,

the brake may not engage at all and the blade will coast to astop.

If a delay or “skipping” occurs, turn the saw on and off 4 or 5 times. If the condition persists, have

the tool serviced by an authorized DeWALT servicecenter.

Always be sure the blade has stopped before removing it from the kerf plate. The brake is not a

substitute for guards. Ensure your own safety by giving the saw your completeattention.

Guard Actuation and Visibility (Fig. L)

CAUTION: Pinch Hazard. To reduce the risk of injury, keep thumb underneath the handle

when pulling the handle down. The lower guard will move up as the handle is pulled down

which could causepinching.

The blade guard on your saw has been designed to automatically raise when the arm is brought

down and to lower over the blade when the arm israised.

The guard can be raised by hand when installing or removing saw blades or for inspection of the

saw. NEVER RAISE THE BLADE GUARD MANUALLY UN LESS THE SAW IS TURNEDOFF.

NOTE: Certain special cuts of large material will require that you manually raise the guard. Refer

to Cutting Large Material under SpecialCuts.

The front section of the guard is louvered for visibility while cutting. Although the louvers

dramatically reduce flying debris, they are openings in the guard and safety glasses should be

worn at alltimes.

Fig. L

ENGLISH

Miter Lock Adjustment (Fig. M)

The miter lock rod should be adjusted if the table of the saw can be moved when the miter

lock handle is locked down. To adjust, put the miter lock handle in the up position. Using a

slotted screwdriver, adjust the lock rod in 1/8 clockwise turn increments to increase the lock

force. To ensure the miter lock is functioning properly, re-lock miter lock handle to a non-detent

miterangle.

Fig. M

Controls

Your compound miter saw has several main controls, which will be discussed briefly here. For

more information on these controls, see the respective sections later in themanual.

Miter Control (Fig. A)

The miter lock lever 5 and miter detent latch 6 allow you to miter your saw 50° left and right.

To miter the saw, unlock miter lock lever 5 by rotating the knob counter clockwise, squeeze the

miter detent latch 6 and set the miter angle desired on the miter scale. Lock miter lock knob by

rotating clockwise until tight. Override the miter detent by rotatingthe miter detent override 22.

Use of CUTLINE LED Worklight System (Fig. A)

DWS716XPS ONLY

NOTE: The miter saw must be connected to a power source.

The CUTLINE LED Worklight System is equipped with an ON/OFF switch 23 . The CUTLINE LED

Worklight System is independent of the miter saw’s trigger switch.

The light does not need to be on in order to operate the saw.

To cut through an existing pencil line on a piece of wood, turn on the CUTLINE system, then

pull down on the operating handle to bring the saw blade close to the wood. The shadow of

the blade will appear on the wood. This shadow line represents the material that the blade will

remove when performing a cut. To correctly locate your cut to the pencil line, align the pencil

line with the edge of the blade’s shadow. Keep in mind that you may have to adjust the miter or

bevel angles in order to match the pencil line exactly.

Bevel Lock (Fig. J)

The bevel lock knob 11 allows you to bevel the saw 48° left or right. To loosen the handle and

adjust the bevel setting, turn the handle counter clock wise, the saw head bevels easily to the

left or to the right once the bevel stop override knob 31 is pulled. To tighten, turn the handle

clockwise. Bevel degree markings are on the bottom front of the sawarm.

0° Bevel Override (Fig. J)

The bevel stop override knob 31 allows you to bevel the saw to the right past the 0°mark.

The saw will automatically stop at 0° when brought up from the left. To move past 0° to the right,

pull the bevel stop knob. The stop knob can be locked out by pulling the knob out and rotating

it 180°.

45° Bevel Stop Overrides (Fig. J)

The 45° bevel override levers 20 are held secure with their attachment screw to prevent

inadvertent movement. Use the bit on the blade wrench to loosen the attachment screw. This

allows the slides, to be pulled outward and the saw head to pivot past the 45° mark. Be sure to

retighten the attachment screw whenfinished.

Crown Bevel Pawls (Fig. J)

When cutting crown molding laying flat, your saw is equipped to accurately and rapidly set

a crown stop, left or right (refer to Instructions for Cutting Crown Molding Laying Flat and

Using the Compound Features). The crown bevel pawl 42 can be rotated to contact the crown

adjustment screw. The saw is factory set to be used for typical crown in North America (52/38),

but can be reversed to cut non-typical (45/45) crown. To reverse the crown bevel pawl, remove

the retaining screw, the 22.5° bevel pawl and the 33.9° crown bevel pawl. Flip the crown bevel

pawl so the 30° text is facing up. Reattach the screw to secure the 22.5° bevel pawl and the crown

bevel pawl. The accuracy setting will not beaffected.

22.5° Bevel Pawls (Fig. J)

Your saw is equipped to rapidly and accurately set a 22.5° bevel, left or right. The 22.5° bevel

pawl 41 can be rotated to contact the crown adjustmentscrew.

Head Lock Down Pin (Fig. A)

WARNING: The lock down pin should be used ONLY when carrying or storing the

saw. NEVER use the lock down pin for any cuttingoperation.

To lock the saw head in the down position, push the head down, push the head lock pin 17 in

and release the saw head. This will hold the saw head safely down for moving the saw from place

to place. To release, press the saw head down and pull the pinout.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect

it from power source before making any adjustments or removing/installing

attachments or accessories. An accidental start-up can causeinjury.

WARNING: Always use eye protection. All users and bystanders must wear eye protection

that conforms to ANSI Z87.1 (CAN/CSA Z94.3).

Plug the saw into any household 60 Hz power source. Refer to the nameplate for voltage. Be sure

the cord will not interfere with yourwork.

Body and Hand Position (Fig. N1–N4)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position

asshown.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of

a suddenreaction.

Proper positioning of your body and hands when operating the miter saw will make cutting

easier, more accurate and safer. Never place hands near cutting area. Place hands no closer than

4" (100mm) from the blade. Hold the workpiece tightly to the table and the fence when cutting.

Keep hands in position until the trigger has been released and the blade has completely stopped.

ALWAYS MAKE DRY RUNS (UNPOWERED) BEFORE FINISH CUTS SO THAT YOU CAN CHECK THE

PATH OF THE BLADE. DO NOT CROSS ARMS, AS SHOWN IN FIGUREN3.

Keep both feet firmly on the floor and maintain proper balance. As you move the miter arm

left and right, follow it and stand slightly to the side of the saw blade. Sight through the guard

louvers when following a pencilline.

Fig. N1

Fig. N3

Fig. N2

Fig. N4

Trigger Switch (Fig. O)

To turn the saw on, push the lock-off lever 35 to the left, then depress the trigger switch 1. The

saw will run while the switch is depressed. Allow the blade to spin up to full operating speed

before making the cut. To turn the saw off, release the switch. Allow the blade to stop before

raising the saw head. There is no provision for locking the switch on. A hole 36 is provided in the

trigger for insertion of a padlock to lock the switchoff.

Always be sure the blade has stopped before removing it from thekerf.

Fig. O

ENGLISH

Dust Extraction (Fig. P)

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect

it from power source before making any adjustments or removing/installing

attachments or accessories. An accidental start-up can causeinjury.

Your saw has a built-in dust port 12 that allows either the supplied dust bag 37 or a shop

vacuum system to beconnected.

NOTE: This saw has a dust port equipped with an AirLockTM fitting, which is a universal system

that connects tools to dust extraction shrouds to minimize cleanup on thejobsite.

To Attach the Dust Bag

1. Fit the dust bag 37 to the dust port 12 as shown in FigureP.

Fig. P

To Empty the Dust Bag

1. Remove dust bag 37 from the saw and gently shake or tap the dust bag toempty.

2. Reattach the dust bag back onto the dust port 12.

You may notice that all the dust will not come free from the bag. This will not affect cutting

performance but will reduce the saw's dust collection efficiency. To restore your saw's dust

collection efficiency, depress the spring inside the dust bag when you are emptying it and tap it

on the side of the trash can or dustreceptacle.

CAUTION: Never operate this saw unless the dust bag or DeWALT dust extractor is in

place. Wood dust may create a breathinghazard.

Cutting with Your Saw

NOTE: Although this saw will cut wood and many non-ferrous materials, we will limit our

discussion to the cutting of wood only. The same guidelines apply to the other materials. DO

NOT CUT FERROUS (IRON AND STEEL) MATERIALS OR MASONRY WITH THIS SAW. Do not

use any abrasiveblades.

Crosscuts

Cutting of multiple pieces is not recommended but can be done safely by ensuring that each

piece is held firmly against the table and fence. A crosscut is made by cutting wood across the

grain at any angle. A straight crosscut is made with the miter arm at the zero degree position. Set

the miter arm at zero, hold the wood on the table and firmly against the fence. Turn on the saw

by squeezing thetrigger.

CAUTION: Always use a work clamp to maintain control and reduce the risk of workpiece

damage and personalinjury.

When the saw comes up to speed (about 1 second) lower the arm smoothly and slowly to cut

through the wood. Let the blade come to a full stop before raisingarm.

Miter crosscuts are made with the miter arm at some angle other than zero. This angle is often

45° for making corners, but can be set anywhere from zero to 50° left or right. After selecting the

desired miter angle, be sure to secure the miter lock lever. Make the cut as describedabove.

To cut through an existing pencil line on a piece of wood, match the angle as close as possible.

Cut the wood a little too long and measure from the pencil line to the cut edge to determine

which direction to adjust the miter angle and recut. This will take some practice, but it is a

commonly usedtechnique.

Bevel Cuts (Fig. A)

A bevel cut is a crosscut made with the saw blade at a bevel to the wood. In order to set the

bevel, loosen the bevel lock knob 11 and move the saw to the left as desired. (It is necessary to

move the fence to allow clearance). Once the desired bevel angle has been set, tighten the bevel

clamp knobfirmly.

Bevel angles can be set up to 48° left and can be cut with the miter arm set between zero and 50°

right or left. At some extreme angles, the left side fence might have to be removed. To remove

the left fence, unscrew the fence lock knob 14 several turns and slide the fenceout.

Quality of cut

The smoothness of any cut depends on a number of variables. Things like material being cut,

blade type, blade sharpness and rate of cut all contribute to the quality of thecut.

When smoothest cuts are desired for molding and other precision work, a sharp (60 tooth

carbide) blade and a slower, even cutting rate will produce the desiredresults.

Ensure that material does not creep while cutting, clamp it securely in place. Always let the blade

come to a full stop before raisingarm.

If small fibers of wood still split out at the rear of the workpiece, stick a piece of masking tape on

the wood where the cut will be made. Saw through the tape and carefully remove tape

whenfinished.

For varied cutting applications, refer to the list of recommended saw blades for your saw and

select the one that best fits your needs. Refer to Saw Blades underOptional Accessories.

Clamping the Workpiece (Fig. A)

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make anyadjustments.

WARNING: A workpiece that is clamped, balanced and secure before a cut may become

unbalanced after a cut is completed. An unbalanced load may tip the saw or anything the

saw is attached to, such as a table or workbench. When making a cut that may become

unbalanced, properly support the workpiece and ensure the saw is firmly bolted to a stable

surface. Personal injury mayoccur.

WARNING: The clamp foot must remain clamped above the base of the saw whenever the

clamp is used. Always clamp the workpiece to the base of the saw–not to any other part of

the work area. Ensure the clamp foot is not clamped on the edge of the base of thesaw.

CAUTION: Always use a work clamp to maintain control and reduce the risk of workpiece

damage and personalinjury.

If you cannot secure the workpiece on the table and against the fence by hand, (irregular shape,

etc.) or your hand would be less than 4" (100mm) from the blade, a clamp or other fixture must

beused.

For best results use the vertical material clamp 21 provided with your saw. Additional DW7090

clamps can be purchased at your local retailer or DeWALT servicecenter.

Other aids such as spring clamps, bar clamps or C-clamps may be appropriate for certain sizes

and shapes of material. Use care in selecting and placing these clamps. Take time to make a dry

run before making the cut. The left fence will slide from side to side to aid in clamping

To Install Clamp (Fig. A)

1. Insert the vertical material clamp 21 into one of the four clamp mounting holes 15 on

thebase.

2. Lifting up on the arm of the clamp can rapidly adjust the height, then use the fine adjust

knob to firmly clamp theworkpiece.

NOTE: Place the clamp on the opposite side of the base when beveling. ALWAYS MAKE DRY

RUNS (UNPOWERED) BEFORE FINISH CUTS TO CHECK THE PATH OF THE BLADE. ENSURE THE

CLAMP DOES NOT INTERFERE WITH THE ACTION OF THE SAW ORGUARDS.

WARNING: A workpiece that is clamped, balanced and secure before a cut may become

unbalanced after a cut is completed. An unbalanced load may tip the saw or anything the

saw is attached to, such as a table or workbench. When making a cut that may become

unbalanced, properly support the workpiece and ensure the saw is firmly bolted to a

stablesurface.

WARNING: The clamp foot must remain clamped above the base of the saw whenever the

clamp is used. Always clamp the workpiece to the base of the saw–not to any other part of

the work area. Ensure the clamp foot is not clamped on the edge of the base of thesaw.

Support for Long Pieces

WARNING: To reduce the risk of serious personal injury, turn off the tool and

disconnect it from the power source before attempting to move it, change

accessories or make anyadjustments.

ALWAYS SUPPORT LONGPIECES.

Never use another person as a substitute for a table extension; as additional support for a

workpiece that is longer or wider than the basic miter saw table or to help feed, support or pull

theworkpiece.

For best results, use the DWX723, DWX724, DWX725B or DWX726 miter saw stand to extend the

table width of your saw. These are available from your dealer at extracost.

Support long workpieces using any convenient means such as sawhorses or similar devices to

keep the ends fromdropping.

Cutting Picture Frames, Shadow Boxes and Other Four-Sided

Projects (Fig. Q)

To best understand how to make the items listed here, we suggest that you try a few simple

projects using scrap wood until you develop a “FEEL” for yoursaw.

Your saw is the perfect tool for mitering corners like the one shown in FigureQ. Sketch A in

FigureQ shows a joint made by using the bevel adjustment to bevel the edges of the two boards

at 45° each to produce a 90° miter corner. For this joint the miter arm was locked in the zero

position and the bevel adjustment was locked at 45°. The wood was positioned with the broad

flat side against the table and the narrow edge against the fence. The cut could also be made by

mitering right and left with the broad surface against thefence.

Cutting Trim Molding and Other Frames (Fig. Q)

Sketch B in FigureQ shows a joint made by setting the miter arm at 45° to miter the two boards

to form a 90° corner. To make this type of joint, set the bevel adjustment to zero and the miter

arm to 45°. Once again, position the wood with the broad flat side on the table and the narrow

edge against thefence.

The two sketches in FigureQ are for four sided objectsonly.

ENGLISH

As the number of sides changes, so do the miter and bevel angles. The chart below gives the

proper angles for a variety of shapes. The chart assumes that all sides are of equal length. For a

shape that is not shown in the chart, use the following formula. 180° divided by the number of

sides equals the miter or bevelangle.

EXAMPLES

No. Sides Angle Miter or Bevel

445°

536°

630°

725.7°

822.5°

920°

10 18°

Fig. Q

A B

Cutting Compound Miters (Fig. R, S)

A compound miter is a cut made using a miter angle and a bevel angle at the same time. This is

the type of cut used to make frames or boxes with slanting sides like the one shown in FigureR.

NOTE: If the cutting angle varies from cut to cut, check that the bevel clamp knob and the miter

lock knob are securely tightened. These knobs must be tightened after making any changes in

bevel ormiter.

The chart (Table 1) will assist you in selecting the proper bevel and miter settings for common

compound miter cuts. To use the chart, select the desired angle “A” (FigureS, Angle A+Exteriors

Angles = 90°) of your project and locate that angle on the appropriate arc in the chart. From that

point follow the chart straight down to find the correct bevel angle and straight across to find the

correct miterangle.

Set your saw to the prescribed angles and make a few trial cuts. Practice fitting the cut pieces

together until you develop a feel for this procedure and feel comfortable withit.

EXAMPLE: To make a 4 sided box with 65° exterior angles(FigureS), 25°(Angle A) = 90° – 65°(Exteriors

Angles), use the upper right arc. Find 25° on the arc scale. Follow the horizontal intersecting line to

either side to get miter angle setting on saw (23°). Likewise, follow the vertical intersecting line to

the top or bottom to get the bevel angle setting on the saw (40°). Always try cuts on a few scrap

pieces of wood to verify settings onsaw.

Fig. R Fig. S

Exteriors

Angles

Angle A

Vernier Scale (Fig. T1, T2)

Your saw is equipped with a vernier scale for added precision. The vernier scale allows you to

accurately set miter angles to the nearest 1/4°. To use the vernier scale follow the steps listed

below.

(As an example, let’s assume that the angle you want to miter is 24-1/4° right).

1. Turn off miter saw.

2. Set the miter angle to the nearest whole degree desired by aligning the center mark in the

vernier scale, shown in Figure T1, with the whole degree number etched in the miter scale.

Examine Figure T1 closely; the setting shown is 24° right miter.

Center mark on vernier scale aligns

with desired whole angle on miter

scale (24° right miter)

Fig. T1

3. To set the additional 1/4°, squeeze the miter arm lock and carefully move the arm to the

RIGHT until the 1/4° vernier mark aligns with the CLOSEST degree mark on the miter scale. In

our example, the closest degree mark on the miter scale happens to be 25°. Figure T2 shows

a setting of 24-1/4° right miter.

For settings that require partial degrees (1/4, 1/2, 3/4°) align the desired vernier mark with

the CLOSEST degree mark on the miter scale, as described below (The plastic vernier plate is

inscribed with marks for 1/4, 1/2, 3/4 and 1°. Only the 1/2° and the 1° are numerically labeled.)

Fig. T2

Miter Angle

1/4° vernier mark aligns with closest

whole degree mark on miter scale

(24-1/4° right miter)

When Mitering to the Right

To increase the miter angle when mitering to the right, move the arm to align the appropriate

vernier mark with the closest mark on the miter scale to the right. To decrease the miter angle

when mitering to the right, move the arm to align the appropriate vernier mark with the closest

mark on the miter scale to theleft.

When Mitering to the Left

To increase the miter angle when mitering to the left, move the arm to align the appropriate

vernier mark with the closest mark on the miter scale to the left. To decrease the miter angle

when mitering to the left, move the arm to align the appropriate vernier mark with the closest

mark on the miter scale to theright.

Cutting Base Molding (Fig. U)

ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANYCUTS.

Straight 90° Cuts

Position the wood against the fence and hold it in place as shown in FigureU. Turn on the saw,

allow the blade to reach full speed and lower the arm smoothly through thecut.

ENGLISH

Fig. U

Cutting Base Molding up to 6.5" (165 mm) Vertically Against the

Fence (Fig. V)

Position molding as shown in FigureV.

All cuts made with the back of the molding against the fence and bottom of the molding against

thebase.

Inside corner Outside corner

Left side 1. Miter left 45°

2. Save left side of cut

1. Miter right 45°

2. Save right side of cut

Right side 1. Miter right 45°

2. Save right side of cut

1. Miter left 45°

2. Save right side of cut

Material up to 6.5"(165mm) can be cut as describedabove.

Cutting Crown Molding

Your miter saw is better suited to the task of cutting crown molding than any tool made. In order

to fit properly, crown molding must be compound mitered with extremeaccuracy.

The two flat surfaces on a given piece of crown molding are at angles that, when added together,

equal exactly 90°. Most, but not all, crown molding has a top rear angle (the section that fits flat

against the ceiling) of 52° and a bottom rear angle (the part that fits flat against the wall) of38°.

Your miter saw has special pre-set miter latch points at 31.6° left and right for cutting crown

molding at the proper angle and bevel stop pawls at 33.9° left and right. There is also a mark on

the bevel scale at 33.9°.

The Bevel Symbol/Miter Symbol chart gives the proper settings for cutting crown molding. (The

numbers for the miter and bevel settings are very precise and are not easy to accurately set on

your saw.) Since most rooms do not have angles of precisely 90°, you will have to fine tune your

settingsanyway.

PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!

Instructions for Cutting Crown Molding Laying Flat and Using

the Compound Features (Fig. A, V)

1. Molding laying with broad back surface down flat on saw table 38.

Fig. V

2. For standard U.S. crown molding with a 52°/38° spring angle, match the following semi-circle

symbols on your saws bevel and miter scales per the chartbelow.

BEVEL SYMBOL MITER SYMBOL

TYPE OF CUT MITER ANGLE BEVEL ANGLE

Left side, Inside corner 31.6° right 33.9° left

Right side, Inside corner 31.6° right 33.9° right

Left side, Outside corner 31.6° left 33.9° right

Right side, Outside corner 31.6° right 33.9° left

For non-standard crown molding with a 45° spring angle, match the following triangle

symbols on your saws bevel and miter scales per the chartbelow.

BEVEL SYMBOL MITER SYMBOL

TYPE OF CUT MITER ANGLE BEVEL ANGLE

Left side, Inside corner 35.3° right 30° left

Right side, Inside corner 35.3° right 30° right

Left side, Outside corner 35.3° left 30° right

Right side, Outside corner 35.3° right 30° left

When setting bevel and miter angles for all compound miters, remember that:

The angles presented for crown moldings are very precise and difficult to set exactly. Since they

can easily shift slightly and very few rooms have exactly square corners, all settings should be tested

on scrapmolding.

PRETESTING WITH SCRAP MATERIAL IS EXTREMELY IMPORTANT!

Alternative Method for Cutting Crown Molding (Fig. W)

Place the molding on the table at an angle between the sliding fence 10 and the saw

table38 , as shown in FigureW. Use of the crown molding fence accessory (DW7084) is highly

recommended because of its degree of accuracy and convenience. The crown molding fence

accessory is available for purchase from your localdealer.

The advantage to cutting crown molding using this method is that no bevel cut is required.

Minute changes in the miter angle can be made without affecting the bevel angle. This way,

when corners other than 90° are encountered, the saw can be quickly and easily adjusted for

them. Use the crown molding fence accessory to maintain the angle at which the molding will

be on thewall.

Fig. W

Instructions for Cutting Crown Molding Angled Between the

Fence and Base of the Saw for All Cuts

1. Angle the molding so the bottom of the molding (part which goes against the wall when

installed) is against the fence and the top of the molding is resting on the base of the saw, as

shown in FigureW.

2. The angled “flats” on the back of the molding must rest squarely on the fence and base of

thesaw.

Inside corner Outside corner

Left side 1. Miter right 45°

2. Save right side of cut

1. Miter left 45°

2. Save right side of cut

Right side 1. Miter left 45°

2. Save left side of cut

1. Miter right 45°

2. Save left side of cut

Special Cuts

NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST

THEFENCE.

Aluminum Cutting (Fig. A, X, Y)

ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM. These

are available at your local DeWALT retailer or DeWALT service center. Certain workpieces, due to

their size, shape or surface finish, may require the use of a clamp or fixture to prevent movement

during the cut. Position the material so that you will be cutting the thinnest cross section, as

shown in FigureX. FigureY illustrates the wrong way to cut these extrusions. Use a stick wax

cutting lubricant when cutting aluminum. Apply the stick wax directly to the saw blade 26

before cutting. Never apply stick wax to a movingblade.

The wax, available at most hardware stores and industrial mill supply houses, provides proper

lubrication and keeps chips from adhering to theblade.

Be sure to properly secureworkpiece.

ENGLISH

Fig. X

RIGHT

Fig. Y

WRONG

10 26

Refer to Saw Blades under Accessories for correct sawblade.

Bowed Material (Fig. Z, AA)

When cutting bowed material always position it as shown in FigureZ and never like that shown

in Figure AA. Positioning the material incorrectly will cause it to pinch the blade near the

completion of thecut.

Fig. Z

Fig. AA

Cutting Plastic Pipe or Other Round Material

Plastic pipe can be easily cut with your saw. It should be cut just like wood and CLAMPED OR

HELD FIRMLY TO THE FENCE TO KEEP IT FROM ROLLING. This is extremely important when

making anglecuts.

Cutting Large Material (Fig. L)

Occasionally you will encounter a piece of wood a little too large to fit beneath the lower guard.

To clear the guard over the wood, with the motor off and your right hand on the operating

handle, place your right thumb outside of the upper portion of the guard and roll the guard

up just enough to clear the wood, as shown in Figure L. Release the guard prior to starting the

motor. The guard mechanism will function properly during the cut. Only do this when necessary.

NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN WHEN OPERATING THISSAW.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect

it from power source before making any adjustments or removing/installing

attachments or accessories. An accidental start-up can causeinjury.

WARNING: To reduce the risk of serious personal injury, DO NOT touch the sharp points on

the blade with fingers or hands while performing anymaintenance.

DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic

guard. The polycarbonate material used in the guard is subject to attack by certainchemicals.

1. All bearings are sealed. They are lubricated for life and need no furthermaintenance.

2. Periodically clean all dust and wood chips from around AND UNDER the base and the

rotary table. Even though slots are provided to allow debris to pass through, some dust

willaccumulate.

3. The brushes are designed to give you several years of use. To replace the brushes, return the

tool to the nearest service center for repair. A list of service center locations is packed with

yourtool.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.

To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when

performingthis procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a

cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never

immerse any part of the tool into aliquid.

Accessories

WARNING: Since accessories, other than those offered by DeWALT, have not been tested

with this product, use of such accessories with this tool could be hazardous. To reduce the

risk of injury, only DeWALT recommended accessories should be used with thisproduct.

Recommended accessories for use with your tool are available at extra cost from your local dealer

or authorized service center. If you need assistance in locating any accessory, please contact

DeWALT Industrial Tool Co., 701East Joppa Road, Towson, MD 21286, call 1-800-4-DeWALT

(1-800-433-9258) or visit our website: www.dewalt.com.

Optional Accessories

The following accessories, designed for your saw, may be helpful. Use care in selecting and

usingaccessories.

Clamp: DW7090

Used for firmly clamping workpiece to the saw fence for precisioncutting.

Dust Bag: DW7053

Included with some models

Equipped with a zipper for easy emptying, the dust bag will capture the majority of the

sawdustproduced.

Crown Molding Fence: DW7084

Used for precision cutting of crownmolding.

Miter Saw Stands: DWX723, DWX724, DWX725B, DWX726

Provides stable and accurate work platform for mitersaws.

Saw Blades

ALWAYS USE 12" (305 mm) SAW BLADES WITH 1" (25.4 mm) ARBOR HOLES. SPEED RATING

MUST BE AT LEAST 4800 RPM. Never use a smaller diameter blade. It will not be guarded

properly. Use crosscut blades only! Do not use blades designed for ripping, combination blades

or blades with hook angles in excess of 7˚.

BLADE DESCRIPTIONS

APPLICATION DIAMETER TEETH

Construction Saw Blades (maximum thin kerf with anti-stick rim)

General Purpose 12" (305 mm) 32/40

Fine Crosscuts 12" (305 mm) 60

Woodworking Saw Blades (provide smooth, clean cuts)

Fine crosscuts 12" (305 mm) 80

Non-ferrous metals 12" (305 mm) 96

NOTE: For cutting non-ferrous metals, use only saw blades with TCG teeth designed for this purpose.

ENGLISH

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE! WHAT’S WRONG? WHAT TO DO

Saw will not start Saw not plugged in Plug in saw.

Fuse blown or circuit breaker tripped Replace fuse or reset circuit breaker.

Cord damaged Have cord replaced by authorized service center.

Brushes worn out Have brushes replaced by authorized service center.

Saw makes unsatisfactory cuts Dull blade Replace blade. Refer to Changing or Installing a New Saw Blade.

Blade mounted backwards Turn blade around. Refer to Changing or Installing a New Saw Blade.

Gum or pitch on blade Remove blade and clean with turpentine and coarse steel wool or household oven cleaner.

Incorrect blade for work being done Change the blade type. Refer to Saw Blades under Accessories.

Blade does not come up to speed Extension cord too light or too long Replace with adequate size cord. Refer to Additional Saftey Rules for Miter Saws.

Low house current Contact your electric company.

Machine vibrates excessively Saw not mounted securely to stand or work bench Tighten all mounting hardware. Refer to Bench Mounting.

Stand or bench on uneven floor Reposition on flat level surface. Refer to Familiarization.

Damaged saw blade Replace blade. Refer to Changing or Installing a New Saw Blade.

Does not make accurate miter cuts Miter scale not adjusted correctly Check and adjust. Refer to Miter Scale Adjustment under Assembly and Adjustments.

Blade is not square to fence Check and adjust. Refer to Miter Scale Adjustment under Assembly and Adjustments.

Blade is not perpendicular to table Check and adjust fence. Refer to Bevel Square to Table under Assembly and Adjustments.

Workpiece moving Clamp workpiece securely to fence or glue 120 grit sandpaper to fence with rubber cement.

Material pinches blade Cutting bowed material Refer to Bowed Material under Special Cuts.

Repairs

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (including brush inspection and replacement, when applicable) should be

performed by a DeWALT factory service center or a DeWALT authorized service center. Always

use identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof ofpurchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely

event a safety notification is required under the Federal Consumer SafetyAct.

Three Year Limited Warranty

DeWALT will repair, without charge, any defects due to faulty materials or workmanship for

three years from the date of purchase. This warranty does not cover part failure due to normal

wear or tool abuse. For further detail of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-DeWALT (1-800-433-9258). This warranty does not apply

to accessories or damage caused where repairs have been made or attempted by others. THIS

LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential damages, so these

limitations may not apply to you. This warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty, DeWALT tools are covered byour:

1 YEAR FREE SERVICE

DeWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year afterpurchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DeWALT Power Tool, Laser, or

Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for

a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained in the packaging, call

the local company or see website for warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,

call 1-800-4-DeWALT (1-800-433-9258) for a freereplacement.

ENGLISH

TABLE 1: COMPOUND MITER CUT

(POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)

SET THIS MITER ANGLE ON SAW

SQUARE BOX

6-SIDED BOX

SET THIS BEVEL ANGLE ON SAW

8-SIDED BOX

ANGLE A (SPRING ANGLE OF CROWN)

FRANÇAIS

Français (traduction de la notice d’instructions originale)

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations dangereuses et de risques de dommages corporels oumatériels.

DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des blessuresgraves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la mort ou des blessuresgraves.

ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des blessures légères oumodérées.

(Si utilisé sans aucun terme) Indique un message propre à lasécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de dommagesmatériels.

Fig. A

AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect des

avertissements et des directives pourrait se solder par un

choc électrique, un incendie et/ou une blessuregrave.

AVERTISSEMENT : afin de réduire le risque de blessures, lire

le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil ou de

tout autre outil DeWALT, composez le numéro sans frais :

1-800-4-DeWALT (1-800-433-9258).

1 Gâchette

2 Poignée de manœuvre

3 Trous de montage

4 Protecteur inférieur

5 Levier de verrouillage des onglets

6 Déclencheur du cran des onglets

7 Échelle des onglets

8 Vis de l’échelle des onglets

9 Encoches pour mains

10 Guide coulissant

11 Bouton de verrouillage en biseau

12 Capteur de poussière

13 Poignée de transport

14 Bouton de verrouillage du guide

15 Trous de montage du serre-joint

16 Clé hexagonale 6 mm

17 Tige de verrouillage de la tête

18 Guide de base

19 Vis d’ajustement de la butée en

biseau 45°

20 Leviers de dépassement de la butée

en biseau 45°

21 Serre-joint vertical du matériau

22 Bouton de libération du cran des

onglets

23 DEL CUTLINE est équipé d’un

interrupteur marche/arrêt

(DWS716XPS seulement)

567

DWS716XPS

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX POUR LES OUTILS

ÉLECTRIQUES

AVERTISSEMENT: lisez tous les avertissements de sécurité, toutes les instructions,

les illustrations et les caractéristiques fournis avec cet outil électrique. Ne pas suivre

toutes les instructions comprises aux présentes peut conduire à un choc électrique, un

incendie et/ou des blessuresgraves.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à

alimentation sur secteur (avec fil) ou par piles (sansfil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil

électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier

la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches

non modifiées correspondant à laprise.

b ) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est plus

élevé si votre corps est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau

dans un outil électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de

la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira

les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un

disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les

risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un

outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention

en utilisant un outil électrique peut entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des

chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la

situation le requiert réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la

position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer

un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors

que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à

la position de marche risque de provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé

de réglage attachée à une partie pivotante de l’outil électrique peut provoquer des

blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de

mieux maîtriser l’outil électrique dans les situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de

bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles.

Les vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le raccordement de dispositifs de

dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés et

utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser votre connaissance acquise suite l’utilisation fréquente des outils

vous permettre de baisser la garde et ignorer les principes de sécurité de l’outil. Un

acte irréfléchi peut causer une blessure grave en une fraction deseconde.

4) Utilisation et entretien d’un outil électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a étéconçu.

b ) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit êtreréparé.

c ) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de

ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée des enfants et ne permettre à

aucune personne n’étant pas familière avec un outil électrique ou son mode

d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

e ) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou

coincées, si des pièces sont brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique. En cas de dommage, faire

réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à

effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour

laquelle il a été conçu estdangereuse.

h ) Gardez vos mains et les surfaces de prise sèches, propres et libres de graisse et de

poussière. Les mains et les surfaces de prise glissante ne permettent pas la manutention et

le contrôle sécuritaires de l’outil dans les situationsimprévues.

5) Réparation

a ) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que

des pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire

de l’outilélectrique.

Consignes de sécurité propres aux scies à onglet

a ) Les scies à onglet ont été conçues pour découper le bois ou des produits similaires.

Elles ne peuvent être utilisées avec des meules à tronçonner pour découper des

matériaux ferreux tels barres, tiges, montants, etc. Les poussières abrasives pourront

enrayer les pièces mobiles comme le carter inférieur. Les étincelles provenant de la découpe

abrasive pourront brûler le carter inférieur, la plaque du trait de scie ou toute autre pièce

enplastique.

b ) Utilisez des serre-joints pour soutenir les pièces de travail lorsque possible. Si vous

soutenez la pièce de travail à la main, vous devez toujours garder votre main à au

moins 100 mm de chaque côté de la lame de la scie. Ne pas utiliser cette scie pour

couper des pièces trop petites pour être arrimées ou tenues manuellement de façon

sécuritaire. Si la main s’approche trop près de la lame, les risques de dommages corporels

par contact avec la lameaugmentent.

c ) La pièce à travailler doit être fixe et bien arrimée, ou maintenue, contre le guide

et la table. Ne jamais alimenter la pièce à travailler vers la lame ou couper à main

levée. Une pièce non maintenue ou mobile pourrait être éjectée à grande vitesse et causer

des dommagescorporels.

d ) Ne jamais laisser la main traverser la ligne de coupe, que ce soit devant ou derrière

la lame. Le fait de maintenir la pièce en croisant les bras (la maintenir du côté droit de la scie

avec la main gauche, ou inversement) est extrêmementdangereux.

e ) Ne pas atteindre l’arrière du guide avec une ou l’autre des mains plus près de

100 mm de chaque côté de la lame de la scie, pour retirer les résidus de bois ou

pour toute autre raison pendant que la lame tourne. La proximité de la lame en

mouvement avec la main pourrait ne pas être évidente et poser des risques de dommages

corporelsgraves.

f ) Vérifier la pièce avant la coupe. Si la pièce est gauchie ou voilée, l’arrimer avec la

courbe externe orientée vers le guide. S’assurer systématiquement qu’il n’y a aucun

espace entre la pièce, le guide et la table le long de la ligne de coupe. Les pièces

gauchies ou voilées peuvent se tordre ou bouger et causer un grippage au niveau de

la lame en mouvement pendant la coupe. La pièce devrait être exempte de clous ou de

tout autre objetétranger.

g ) Ne pas utiliser la scie tant que la table ne sera pas débarrassée de tout outil,

débris de bois, etc., autre que la pièce à travailler. Les petits débris, morceaux de bois,

ou autres objets qui entreraient en contact avec la scie en mouvement pourraient être

éjectésviolemment.

h ) Couper une pièce à la fois. Les pièces mises les unes sur les autres ne peuvent être arrimées

de façon adéquate et pourraient rester coincées dans la lame ou bouger pendant lacoupe.

i ) S’assurer que la scie à onglet est montée ou installée sur une surface plane et ferme

avant son utilisation. Une surface plane et ferme réduit les risques d’instabilité de la scie

àonglet.

j ) Planifier le travail. À chaque changement de réglage d’angle de biseau ou d’onglet,

vérifier que le guide n’interfèrera pas avec la lame et le dispositif de protection.

FRANÇAIS

Alors que l’outil n’est pas en ‘”MARCHE” et qu’aucune pièce ne se trouve sur la table, déplacer

la lame tout du long pour simuler une coupe complète pour s’assurer qu’il n’y aura aucune

interférence ou risque de couper leguide.

k ) Offrir un soutien adéquat, tel que rallonges de table, chevalets, etc., pour toute

pièce plus longue ou plus large que la table de l’établi. Les pièces plus longues ou plus

larges que la table de scie à onglet pourraient tomber si elles ne sont pas soigneusement

soutenues. Si c’était le cas, aussi bien pour la pièce ou la découpe, elles pourraient soulever le

carter inférieur ou être rejetées par la lame enmouvement.

l ) Ne pas utiliser un autre individu comme substitut à une rallonge ou à un support

additionnel. Le soutien instable de la pièce pourra gripper la lame ou faire bouger la pièce

pendant la découpe, et attirer l’utilisateur et son aide vers la lame enmouvement.

m ) La découpe ne doit pas être coincée ou appuyée en aucune façon contre la lame en

mouvement. Si elle était coincée (à l’aide de butées longitudinales), la découpe pourrait être

bloquée contre la lame et rejetéeviolemment.

n ) Utiliser systématiquement un serre-joint ou un dispositif de fixation pour soutenir

correctement des matériaux arrondis comme les barreaux ou la tubulure. Les

barreaux ont tendance à rouler pendant la coupe, gripper la lame et attirer la pièce et la

main vers lalame.

o ) Laisser la lame tourner à plein régime avant de la mettre en contact avec la pièce.

Cela réduira les risques que la pièce soitéjectée.

p ) Si la pièce ou la lame se grippait, arrêter la scie à onglet. Attendre l’arrêt complet de

toutes les pièces mobiles, déconnecter l’outil du secteur et/ou retirer le bloc-piles. Et

alors seulement, libérer le matériau coincé. Le fait de continuer à scier alors que la pièce

est grippée pourra causer la perte de contrôle de la scie à onglet et l’endommager.

q ) Une fois la coupe terminée, relâchez l’interrupteur, maintenir la tête de scie

abaissée et attendre l’arrêt complet de la lame avant de retirer la découpe.

Approcher la main d’une lame au ralenti estdangereux.

r ) Maintenir fermement la poignée pour effectuer une coupe partielle ou pour libérer

l’interrupteur alors que la tête de scie n’est pas encore complètement abaissée. Le

freinage de la scie pourrait abaisser soudainement la tête de scie, et poser des risques de

dommagescorporels.

Règles de sécurité additionnelles relatives aux scies à onglet

AVERTISSEMENT : ne pas laisser une bonne connaissance de l’outil (acquise par l’utilisation

fréquente de la scie) prendre préséance sur les règles de sécurité. Toujours se souvenir qu’une

fraction de seconde d’imprudence est suffisante pour infliger de gravesblessures.

AVERTISSEMENT: ne jamais modifier l’outil électrique ou toute pièce de celui-ci. Cela

pourrait entraîner des dommages matériels ou des blessurescorporelles.

• NE PAS UTILISER CETTE MACHINE tant qu’elle n’est pas complètement assemblée et installée,

conformément aux instructions données. Une machine incorrectement assemblée pose des

risques de dommages corporelsgraves.

• DEMANDER CONSEIL à un supérieur, un instructeur, ou à toute autre personne qualifiée, si

l’on n’est pas complètement familier avec l’utilisation de cette machine. Le savoir est source

desécurité.

• SE CONFORMER AUX NORMES DU CODE EN MATIÈRE DE CÂBLAGE et connexions

électriques pour prévenir tout risque de décharges électriques ou d’électrocution. Protéger la ligne

électrique avec un fusible temporisé d’au moins 15 ampères ou undisjoncteur.

• S’ASSURER QUE la lame tourne dans le bon sens. Les dents de la lame devraient pointer dans le

sens de rotation indiqué sur lascie.

• RESSERRER TOUS LES LEVIERS DE VERROUILLAGE, boutons et autres leviers avant toute

utilisation. Les dispositifs de fixation lâches posent des risques d’éjection rapide et violente de la

pièce àtravailler.

• S’ASSURER que l’ensemble lame et serre-lames est propre, que les côtés encastrés des serre-

lames se trouvent contre la lame et que la vis de l’arbre est resserrée soigneusement. Une lame

mal ou incorrectement arrimée pose des risques de dommages matériels etcorporels.

• NE PAS UTILISER LA SCIE SUR TOUTE AUTRE TENSION AUTRE QUE CELLE SPÉCIFIÉE.

Surchauffe, dommages à l’outil et dommages corporels pourraientsurvenir.

• NE RIEN BLOQUER CONTRE LE VENTILATEUR pour maintenir l’arbre de moteur. Des

dommages à l’outil et dommages corporels pourraientsurvenir.

• NE JAMAIS COUPER DES MÉTAUX MÉTAUX ou la maçonnerie. Ce genre de coupes pourrait

faire éclater les pointes au carbure de la lame et les projeter violemment posant des risques de

dommages corporelsgraves.

• NE JAMAIS PLACER LES MAINS PLUS DE 100 mm (4 po) DE LALAME.

• NE JAMAIS LAISSER AUCUNE PARTIE DU CORPS ENTRER DANS LE SILLAGE DE LA LAME

SCIE, car cela pose des risques de dommagescorporels.

• NE JAMAIS APPLIQUER DE LUBRIFIANT À LAMES SUR UNE LAME EN MOUVEMENT. Lors de

l’application du lubrifiant, les mains pourraient rencontrer la lame et provoquer des dommages

corporelsgraves.

• NE PAS approcher les mains de la lame lorsque la scie est branchée sur une source

d’alimentation. L’activation accidentelle de la lame pose des risques de dommages

corporelsgraves.

• NE JAMAIS APPROCHER LES MAINS DE LA LAME, NI AUTOUR NI DERRIÈRE. Une lame peut

causer des dommages corporelsgraves.

• NE PAS PASSER LES MAINS SOUS LA SCIE à moins qu’elle ne soit à l’arrêt et débranchée. Tout

contact avec la lame de scie pose des risques de dommagescorporels.

• ARRIMER SOIGNEUSEMENT LA MACHINE À UN SUPPORT STABLE. Les vibrations

pourraient faire glisser la machine, ou bouger ou basculer, posant des risques de dommages

corporelsgraves.

• UTILISER UNIQUEMENT DES LAMES DE SCIE À COUPE TRANSVERSALE recommandées pour

scies à onglet. Pour optimiser les résultats, ne pas utiliser de lames à pointes de carbure avec un

angle d’attaque supérieur à 7 degrés. Ne pas utiliser des lames à creux de dent profonds. Elles

pourraient changer de course et toucher le carter, et poser des risques de dommages matériels

et/ou corporelsgraves.

• UTILISER UNIQUEMENT DES LAMES DE LA TAILLE ET DU TYPE CORRECTS indiqués pour cet

outil pour prévenir tout dommage matériel et/ou corporelgrave.

• VÉRIFIER QUE LES LAMES NE COMPORTENT AUCUNE FISSURE ni aucun autre dommage

avant chaque utilisation. Une lame fissurée ou endommagée peut se casser et des morceaux

pourraient être éjectés violemment, et causer des dommages corporels graves. Changer

immédiatement toute lame fissurée ouendommagée.

• NETTOYER LA LAME ET LES SERRE-LAMES avant chaque utilisation. Leur nettoyage

permettra de vérifier qu’ils ne comportent aucun dommage. Une lame ou un serre-lame fissuré

ou endommagé peut se casser et des morceaux pourraient être éjectés violemment, et causer des

dommages corporelsgraves.

• NE PAS UTILISER DE LAMES VOILÉES. Vérifier que la lame tourne correctement et sans

vibration. Une lame qui vibre pose des risques de dommages matériels et corporelsgraves.

• NE PAS utiliser de lubrifiant ou de nettoyant (particulièrement en vaporisateur ou en aérosol)

à proximité du carter en plastique. Le matériau en polycarbonate utilisé pour le carter peut être

attaqué par certains produitschimiques.

• MAINTENIR LES DISPOSITIFS DE PROTECTION EN PLACE et en bon état demarche.

• UTILISER SYSTÉMATIQUEMENT LA PLAQUE DE TRAIT ET LA REMPLACER SI ELLE EST

ENDOMMAGÉE. De petits débris s’accumulant sous la scie pourraient interférer avec la lame de

scie et causer l’instabilité de la pièce lors de lacoupe.

• UTILISER UNIQUEMENT LES SERRE-LAMES RECOMMANDÉS POUR CET OUTIL pour

prévenir tout dommage matériel et/ou corporelgrave.

• ÉLIMINER DES ORIFICES D’AÉRATION DU MOTEUR tout débris ou sciure. Des orifices

d’aération bouchés pourraient causer la surchauffe de la machine et l’endommager. Cela

pourrait aussi provoquer un court-circuit qui poserait de risques de dommages corporelsgraves.

• NE JAMAIS VERROUILLER L’INTERRUPTEUR EN POSITION DE MARCHE (ON), car cela pose

des risques de dommages corporelsgraves.

• NE JAMAIS MONTER SUR L’OUTIL. De sérieux dommages corporels pourraient en résulter si

l’outil basculait ou en cas de contact involontaire avec l’organe decoupe.

• DES INFORMATIONS COMPLÉMENTAIRES sur la sécurité et l’utilisation correcte des

outils électriques (ex.: vidéo sécurité) sont à votre disposition auprès du Power Tool Institute

(l’Institut des outils électriques), 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.

powertoolinstitute. com). Des informations sont aussi à votre disposition auprès du National

Safety Council (Conseil National de la Sécurité), 1121 Spring Lake Drive, Itasca, IL 60143-3201. Se

reporter aux standards de l’institut: American National Standards Institute ANSI 01.1, Directives

de sécurité pour les machines à bois et à la réglementation OSHA 1910. 213 du Ministère du

travailaméricain.

AVERTISSEMENT: le fait de découper des plastiques, du bois enduit de sève ou autres

matériaux pouvant causer l’accumulation de matériaux fondus sur les pointes de lame et le

corps de lame, augmente les risques de surchauffe et de grippage lors de lacoupe.

AVERTISSEMENT: porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes

courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussières si

la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE

SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/MSHA.

AVERTISSEMENT: les scies, meules, ponceuses, perceuses ou autres outils de construction

peuvent produire des poussières contenant des produits chimiques reconnus par l’État

californien pour causer cancers, malformations congénitales ou être nocifs au système

reproducteur. Parmi ces produits chimiques, on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment, ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un traitementchimique.

Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces travaux.

Pour réduire toute exposition à ces produits: travailler dans un endroit bien aéré, en utilisant du

matériel de sécurité homologué, tel un masque antipoussières spécialement conçu pour filtrer les

particulesmicroscopiques.

• Limiter toute exposition prolongée avec les poussières provenant du ponçage, sciage,

meulage, perçage ou toute autre activité de construction. Porter des vêtements de

protection et nettoyer à l’eau savonneuse les parties du corps exposées. Le fait de laisser

la poussière pénétrer dans la bouche, les yeux ou la peau peut favoriser l’absorption de produits

chimiquesdangereux.

AVERTISSEMENT: cet outil peut produire et/ou répandre de la poussière susceptible

de causer des dommages sérieux et permanents au système respiratoire. Utiliser

FRANÇAIS

systématiquement un appareil de protection des voies respiratoires homologué par le NIOSH

ou l’OSHA. Diriger les particules dans le sens opposé au visage et aucorps.

AVERTISSEMENT: pendant l’utilisation, porter systématiquement une protection

auditive individuelle adéquate homologuée ANSI S12.6 (S3.19). Sous certaines

conditions et suivant la durée d’utilisation, le bruit émanant de ce produit pourrait contribuer

à une perte de l’acuitéauditive.

• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles.

Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces piècesmobiles.

• Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG,

American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus le calibre

est petit, et plus sa capacité est grande. Un calibre16, par exemple, a une capacité supérieure

à un calibre18. L’usage d’une rallonge de calibre insuffisant causera une chute de tension qui

entraînera perte de puissance et surchauffe. Si plus d’une rallonge est utilisée pour obtenir une

certaine longueur, s’assurer que chaque rallonge présente au moins le calibre de fil minimum.

Le tableau ci-dessous illustre les calibres à utiliser selon la longueur de rallonge et l’intensité

nominale indiquée sur la plaque signalétique. En cas de doute, utiliser le calibre suivant. Plus le

calibre est petit, plus la rallonge peut supporter decourant.

Calibre minimum pour les cordons d'alimentation

Volts Longueur totale du cordon

d'alimentation en mètre (pieds)

120 V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)

240 V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)

Ampères

AWG

Plus que Pas plus

que

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Non recommandé

L’étiquette apposée sur votre outil peut inclure les symboles suivants. Les symboles et leur définition

sont indiqués ci-après:

V ......................... volts

Hz ....................... hertz

min ..................... minutes

or DC ...... courant continu

...................... fabrication classe I (mis à la terre)

…/min .............. par minute

BPM .................... battements par minute

IPM ..................... impacts par minute

RPM .................... révolutions par minute

sfpm ................... pieds linéaires par minute (plpm)

SPM (FPM) ......... fréquence par minute

A ......................... ampères

W ........................ watts

or AC ........... courant alternatif

or AC/DC .... courant alternatif ou continu

...................... fabrication classe II (double isolation)

no ....................... vitesse à vide

n ......................... vitesse nominale

...................... borne de terre

...................... symbole d’avertissement

..................... radiation visible

..................... protection respiratoire

.....................protection oculaire

.....................protection auditive

..................... lire toute la documentation

Pour des raisons de fonctionnalité et de sécurité, les étiquettes d’avertissement suivantes

figurent sur votre scie àonglet.

SUR LE PARE-MAIN :

DANGER – RESTEZ À L’ÉCART DE LALAME.

SUR LE PARE-MAIN SUPÉRIEUR :

FIXEZ BIEN LE SUPPORT DE FIXATION AVEC LES DEUX VIS AVANT

D’UTILISER LE PRODUIT.

SUR LA TABLE : (À 2 ENDROITS)

AVERTISSEMENT: GARDEZ VOS MAINS ET VOTRE CORPS

HORS DE PORTÉE DE LA TRAJECTOIRE DE LA LAME DE LA SCIE.

TOUT CONTACT AVEC LA LAME ENTRAÎNERA UNE BLESSURE

GRAVE. NE PAS UTILISER LA SCIE SANS LES PROTECTEURS EN

PLACE. VÉRIFIEZ LE SYSTÈME DE PROTECTION AFIN D’ASSURER

QU’IL FONCTIONNE CORRECTEMENT. NE FAIRE AUCUN TRAVAIL À MAIN LEVÉE. NE

JAMAIS TOUCHER L’ARRIÈRE DE LA LAME DE LA SCIE ÉTEIGNEZ L’OUTIL ET ATTENDEZ

QUE LA LAME S’ARRÊTE AVANT DE DÉPLACER LA PIÈCE DE TRAVAIL, MODIFIER LES

RÉGLAGES OU DÉPLACER VOS MAINS. NE JAMAIS CROISER LES BRAS À L’AVANT DE LA

LAME. SERREZ TOUJOURS LES BOUTONS DE RÉGLAGE AVANT CHAQUE UTILISATION.

DÉBRANCHEZ L’ALIMENTATION AVANT DE CHANGER LA LAME OU L’ENTRETIEN.

SUR LA TABLE : (À 2 ENDROITS)

Connexion électrique

S’assurer que votre bloc d’alimentation est compatible avec l’inscription de la plaque

signalétique. 120 volts, c.a. signifie que votre scie ne peut uniquement fonctionner qu’en courant

alternatif. Une diminution de tension de 10 pour cent ou plus risquera de provoquer une perte de

puissance et une surchauffe. Tous les outils DeWALT sont testés en usine. Si l’outil ne fonctionne

pas, vérifier l’alimentation.

Caractéristiques

Capacité de coupe

Onglet gauche ou droit à 50°

Biseau gauche ou droit à 48°

Onglet à 0°

Hauteur maximale 91,5 mm (3,6 po) Largeur résultante 183 mm (7,2 po)

Largeur maximale 200,7 mm (7,9 po) Hauteur résultante 73,7mm (2,9 po)

Onglet à 45°

Hauteur maximale 91,5 mm (3,6 po) Largeur résultante 125 mm (4,9 po)

Largeur maximale 140 mm (5,5 po) Hauteur résultante 73,7 mm (2,9 po)

Biseau à 45° - Gauche

Hauteur maximale 58,4 mm (2,3 po) Largeur résultante 188 mm (7,4 po)

Largeur maximale 40,6 mm (1,6 po) Hauteur résultante 180,3 mm (7,1 po)

Biseau à 45° - Droit

Largeur maximale 200,7 mm (7,9 po) Hauteur résultante 28 mm (1,1 po)

Hauteur maximale 40,6 mm (1,6 po) Largeur résultante 180,3 mm (7,1 po)

La scie est capable de découper des moulures de plinthes de 19 mm (0,75 po) d’épaisseur par

165,1 mm (6,5 po) de hauteur sur un onglet droit ou gauche à 45°.

Entraînement

Moteur 120 V

Moteur 15 ampères

3800 tr/min

Engrenages hélicoïdaux taillés courroie trapézoïdale multiple roulements à rouleau

Lame en carbure

Frein électrique automatique

Désemballage de la scie

Vérifier le contenu de la boîte pliante de la scie à onglets pour s’assurer que toutes les pièces ont

été livrées. En plus de ce mode d’emploi, la boîte pliante devrait contenir :

1 Scie à onglets DWS716 avec lame à pointe au carbure

1 Clé hexagonale 6 mm

1 Sac de poussière

1 Serre-joint vertical du matériau

1 Guide d’utilisation

DESCRIPTION (FIG. A)

AVERTISSEMENT: ne jamais modifier l’outil électrique ni aucun de ses composants, car il y

a risques de dommages corporels oumatériels.

Reportez-vous en FigureA au début de ce manuel pour obtenir la liste complète

descomposants.

Usage Prévu

Cette scie à onglets robuste est conçue pour les applications de coupe du boisprofessionnelles.

NE PAS les utiliser en milieu ambiant humide ou en présence de liquides ou de

gazinflammables.

Cette scie à onglets est un outil électrique professionnel. NE PAS le laisser à la portée des enfants.

Une supervision est nécessaire auprès de tout utilisateur nonexpérimenté.

Familiarisation (Fig. A, B)

La scie à onglets est entièrement assemblée dans la boîte pliante. Ouvrir la boîte et sortir la scie

en la prenant par la poignée de transport 13 , tel qu’il est illustré à la FigureB.

Installez la scie sur une surface plane et lisse comme un établi, une table robuste ou un établi de

scie à ongletDeWALT.

Examiner la FigureA pour se familiariser avec la scie et ses diverses pièces. La section concernant

les réglages renverra à ces termes et il faut savoir quelles sont les différentes pièces et où elles

setrouvent.

ATTENTION : risque de pincement. Pour réduire le risque de blessures, garder le pouce sous

la poignée lors de son abaissement. Lors de l’abaissement de la poignée, le dispositif de

protection inférieur se déplacera vers le haut et pourrait pincer l’utilisateur. La poignée est

placée près du carter pour des coupesparticulières.

Enfoncer doucement la poignée de fonctionnement 2 , puis tirer sur la broche de verrouillage17.

Relâcher doucement la pression descendante, puis tenir le bras en le laissant remonter à sa pleine

hauteur. Utiliser l’épingle de verrouillage pour transporter la scie d’un endroit à l’autre. Pour

verrouiller le bras, tournez le bouton de verrouillage de tête de 1/4de tour et appuyez sur le bras

FRANÇAIS

jusqu’à ce qui se verrouille en place. Utilisez toujours la poignée de transport 13 pour transporter

la scie ou les encoches pour mains 9 comme illustré dans la FigureA.

Fig. B

Montage sur établi (Fig. A)

Les trous de montage 3 sont présents tous les quatre pieds pour faciliter l’installation sur

l’établi, comme illustré dans la Figure A. Ce sont des trous fraisés arrondis avec des vis et des

trous carrés pour l’utilisation avec les «boulons de carrosserie» ou M8 (5/16 po) ou des boulons

du support de la scie à onglets ou des boulons plus petits. Utiliser l’un des trous, il n’est pas

nécessaire d’utiliser les deux.) Toujours fixer fermement la scie à une surface stable pour éviter

tout mouvement. Pour améliorer la portabilité de l’outil, il peut être monté sur une pièce de

contreplaqué de 12,7mm (1/2 po) ou d’une épaisseur supérieure, qui peut à son tour être fixée à

votre support de pièce ou déplacée vers un autre site de travail et fixée ànouveau.

REMARQUE : Si la scie doit être fixée à une pièce de contreplaqué, s’assurer que les vis de

montage ne dépassent pas de la partie inférieure du bois. Le contreplaqué doit reposer à plat sur

le support de la pièce. Lors de la fixation de la scie à toute surface de travail, ne la fixer que sur les

brides de fixation où se situent les trous des vis de montage. L’utilisation des brides de fixation à

tout autre endroit nuirait à coup sûr au fonctionnement adéquat de lascie.

ATTENTION : pour éviter tout grippage et manque de précision, s’assurer que la surface de

montage n’est pas tordue et ne présente pas d’autre défaut. Si la scie bascule sur la surface,

placer une pièce de matériau de faible épaisseur sous l’un des pieds de la scie, jusqu’à ce que

cette dernière soit fermement assise sur la surface demontage.

Transport de la scie (Fig. A)

AVERTISSEMENT : pour réduire tout risque de dommages corporels, éteindre l’outil

et le débrancher avant de le déplacer, de changer les accessoires ou de réaliser

desréglages.

AVERTISSEMENT: afin de réduire le risque de blessure corporelle grave, verrouillez

TOUJOURS le bouton de verrouillage des onglets 5 , le bouton de verrouillage en biseau11,

le bouton de verrouillage de la tête 17 et le bouton de verrouillage du guide 14 avant de

transporter lascie.

AVERTISSEMENT: le bouton de verrouillage des onglets doit être utilisé seulement lors du

transport ou de l’entreposage de la scie. Ne JAMAIS utiliser le bouton de verrouillage pour

toutecoupe.

Afin de bien transporter la scie à onglets d’un endroit à l’autre, une poignée de transport 13 a

été incluse sur le dessus de bras de la scie les encoches pour mains 9 à la base, comme illustré

dans la FigureA. Pour transporter la scie, abaissez le bras de la scie et appuyez sur la tige de

verrouillage de la tête 17 pour sécuriser le bras. Il cliquera en position de verrouillage.

ASSEMBLAGE ET AJUSTEMENTS

AVERTISSEMENT: pour réduire le risque de blessures graves, éteindre l’outil et

retirer le débrancher avant d’effectuer tout réglage et d’enlever ou d’installer tout

accessoire. Un démarrage accidentel peut provoquer desblessures.

Changement ou pose d’une nouvelle lame de scie (Fig. A, C–E)

AVERTISSEMENT : pour réduire tout risque de dommages corporels, éteindre l’outil

et le débrancher avant de le déplacer, de changer les accessoires ou de réaliser

desréglages.

ATTENTION :

• ne jamais enfoncer le bouton de verrouillage de la broche lorsque la lame est sous

tension ou qu’elle continue de tourner après l’arrêt de lascie.

• ne pas couper du métal ferreux (contenant du fer ou de l’acier), de la maçonnerie ou du

fibrociment avec cette scie àonglets.

Dépose de la lame

1. Débrancher lascie.

2. Soulever le bras jusqu’à la position supérieure, puis lever le pare-main 4 aussi haut

quepossible.

3. Desserrer la vis du support du pare-main 39 sans l’enlever de manière à ce que le support

puisse être levé suffisamment haut pour accéder à la vis de la lame 34 . Le pare-main

inférieur demeurera levé en raison de la position de la vis du support de pare-main.

4. Enfoncer le bouton de verrouillage de la broche 24 tout en tournant la lame de scie

manuellement de manière à engager le dispositif deverrouillage.

5. Maintenir le bouton enfoncé et utiliser l’autre main et la clé hexagonale 6 mm 16 pour

desserrer la vis de la lame. (Tourner dans le sens horaire, filets inversés.)

Fig. C

Fig. D

6. Enlever la vis 34 l’attache de lame extérieure 25 et la lame 26. L’attache de lame

interne27, et le cas échéant, l’adaptateur de lame de 25,4mm (1po), peuvent être laissés

sur labroche.

REMARQUE : L’adaptateur de lame 40 de 25,4 mm (1 po) n’est pas utilisé pour les lames

dotées d’un trou de lame de 15,88 mm (5/8po).

Fig. E

25 26

Pose d’une lame

1. Débrancher lascie.

2. Avec le bras relevé, le dispositif de protection inférieur ouvert sur son support, placer la lame

sur la broche, sur l’adaptateur de lame (si une lame à trou de 25,4 mm [1 po] est utilisée),

et contre l’attache de lame de fixation intérieure, les dents se trouvant au bas de la lame et

pointant vers l’arrière de lascie.

3. Assembler l’attache de lame extérieure sur labroche.

4. Poser la vis de la lame et, tout en engageant le bouton de verrouillage de la broche, serrer

fermement la vis 34 avec la clé hexagonale 6 mm. (Tourner dans le sens antihoraire,

filetsinversés.)

REMARQUE : l’adaptateur de lame n’est pas utilisé pour les lames à trou de 15,88 mm

(5/8po) et doit être rangé dans un endroit sûr pour un usageultérieur.

5. Remettre le support de pare-main à sa position d’origine, puis serrer fermement la vis 39 du

support de pare-main afin de maintenir en place lesupport.

AVERTISSEMENT :

• le support du pare-main doit être remis à sa position d’origine et la vis doit être

serrée avant d’activer lascie.

• négliger de le faire risque de faire entrer en contact le pare-main avec la lame

de scie tournante et ainsi causer des dommages à la scie et des blessures

corporellesgraves.

Réglage de l’échelle d’onglets (Fig. A, F)

Placer une équerre contre le guide de la scie et contre la lame. (Ne pas toucher aux extrémités

des dents de scie avec l’équerre. Cela nuira à la précision des mesures.) Déverrouillez le bouton

de verrouillage des onglets 5 et tournez le bras jusqu’à ce que le cran des onglets le verrouille

à la position des onglets 0˚. Ne pas verrouiller le bouton de verrouillage des onglets. Si la

lame de la scie n’est pas exactement perpendiculaire au guide de base 18 , dévissez les trois

vis de l’échelle des onglets 8 qui maintiennent l’échelle des onglets 7 à la base et déplacez

La page charge ...

DeWalt DWS716 12 Inch (305 mm) Double Bevel Compound Miter Saw Manuel utilisateur

Marque: DeWalt

Modèle: DWS716 12 Inch (305 mm) Double Bevel Compound Miter Saw

Catégorie: Scies à onglet

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

DeWalt DWS716 12 Inch (305 mm) Double Bevel Compound Miter Saw Manuel utilisateur

Ce manuel convient également à

DeWalt DWS716 12 Inch (305 mm) Double Bevel Compound Miter Saw Manuel utilisateur

dans d''autres langues

Documents connexes