Modern Forms FH-W1802 Vox 38 Mode d'emploi

Installation Instructions

Vox Flush

works with the

Google Assistant

FH-W1802Vox Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FH-W1802 Vox Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: [email protected]

General Inquiries

Fan Support

FH-W1802Vox Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FH-W1802 Vox Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FH-W1802Vox Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FH-W1802 Vox Instructions 7

Contents

Tools Required

1. Mounting Options 10

2. Hanging the Fan 12

3. Making the Electrical Connections 14

4. Installing the Optional Wall Control 16

5. Finishing the Installation 18

6. Attaching the Fan Blades 18

7. Installing the Adapter Plate 18

8. Installing the LED Luminaire Module 20

9. Controlling the Fan 22

10. Reset 24

11. Breeze Mode 24

12. Application 24

13. Accessories 26

14. Troubleshooting 27-28

FH-W1802Vox Instructions8

6. LED Module

F6IN-120V-R1-30

7. Glass Shade

RPL-F1802-GLA

8. Control Receiver

w/Hardware (**)

F-R3-1802-0**

9. Remote w/Wall Cradle

F-RCBT-WT

• Wood screw (1), screws (2)

• 5/32” lock washers (2),

Ø10xØ4mm flat washers (2)

• 5.4mm lock washers (2),

Ø14xØ6mm flat washer (1)

• Screws with rubber washers (16)

1. Blade Set of 5 (**)

RPL-F1802-**-BD-**

2. Mounting Plate

RPL-F1802-HGR

3. Trim Ring Decorative

RPL-F1802-TRIM-**

4. Motor Assembly

5. Adapter Plate

Package Contents

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

Hardware Bag

RPL-VOXFLUSH-PARTS

** denotes ﬁnish code of fan/blade sweep of fan

FH-W1802 Vox Instructions 9

9

1

2

5

7

6

8

3

4

IMPORTANT: Please make note

of the MAC ID on the

receiver and keep it in a

safe place.

MAC ID

Hanging Weight: 15 lbs

FH-W1802Vox Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Figures 1-1C are examples of diﬀerent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

FH-W1802 Vox Instructions 11

1

1A

1B

2

1

2

3

1. Support Brace

2. Outlet box

3. Joist

FH-W1802Vox Instructions12

2. Hanging the Fan

1. Disconnect power at the breaker to the fan location.

A licensed electrician must install the fan.

2. Remove 1 of 2 screws from the bottom of mounting bracket

and save for use in section 9. Loosen the other screw (Fig. 2).

3. Pass the 120-volt supply wires through the center hole

in the ceiling mounting bracket as shown in (Fig. 2A).

4. Secure the mounting bracket to the ceiling outlet box with the

screws and washers provided with your outlet box (Fig. 2A).

5. Hang fan on hook and secure the safety cable to the building

structure using spring washer, flat washer, and wood screw

provided (Fig. 2B)

NOTE: Safety cable is required for all installations in Canada. Safety

cable is required for ceiling fan and light combinations over 35 lbs. in

both flush and downrod models in the United States.

REMEMBER to turn oﬀ power at the breaker.

Follow the steps below to hang your fan properly:

FH-W1802 Vox Instructions 13

2

2A 2B

1

2

3

2

1

3

4

1. Screw

2. Motor Assemby

3. Trim Ring

1. 120V Wires

2. cUL Listed

Electrical Box

3. Mounting Plate

4. Mounting Screws

(supplied with

outlet box)

1. Wood Screw

2. Safety Cable

3. Trim Ring

4. Motor Housing

1

2

3

4

FH-W1802Vox Instructions14

3. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the motor assembly with the flat side of the

receiver facing the ceiling (Fig. 3).

Motor to Receiver & Receiver to house supply wires (Fig. 3A).

1. Connect the motor assembly ground wire, mounting bracket

ground wire and receiver ground wire to the ground wire in

outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

FH-W1802 Vox Instructions 15

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Assembly Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

3

3A

1. Motor Assembly

2. Receiver

1

2

FH-W1802Vox Instructions16

4. Installing the Optional Wall Control

NOTE: A Bluetooth wall controlaccessory can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall control

to the copper wire from the wall outlet box that feeds back to the

circuit breaker – important for proper fan function.

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall

outlet box that feeds back to the circuit breaker.

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan.

4. Connect the white wire from the wall control to the white (neutral)

wire from the wall outlet box.

5. Carefully tuck the wire connections inside the outlet box. Secure

the wall control with the two (2) wall control screws provided.

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided.

7. Fasten the wall plate to the wall mounting plate.

4

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)

Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

to Fan

From Breaker

* Home Wiring may vary

FH-W1802 Vox Instructions 17

4A

Multi-location wiring

1 2 3

54

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wallplate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 22.

Line/Hot

Red

Green (Green or Bare)

Wallcontroller 1 Wallcontroller 2 Wallcontroller 3

If Applicable

FAN

Neutral/White

Wall Control 1 Wall Control 2 Wall Control 3

FH-W1802Vox Instructions18

5. Finishing the Installation

1. Secure all wire connections with supplied wire ties to assist in

fan installation.

2. Tuck connections neatly into ceiling outlet box.

3. Remove the motor assembly from the hook on the mounting

bracket. Position the motor up to the hanger plate and attach

using two screws through the two key slots in the top of the motor

housing (Fig.5).

NOTE: Make sure the receiver sits flat and does not interfere with

the hook.

4. Align the remaining two circular holes on motor housing with the two

holes on the mounting bracket. Secure by tightening the two screws

previously removed. Push the trim ring up to conceal the screws.

1. Insert the blade through the slot in the housing. Align the holes

in the blade with the fan motor assembly holes and secure with

blade attachment screw with lock washers (Fig. 6).

2. Repeat this procedure with the remaining blades (Fig. 6).

1. Remove one of the three mounting plate screws from the

mounting ring and loosen the other two screws (do not remove).

2. Place the key holes in the mounting plate over the two screws

previously loosened from the mounting ring. Turn the mounting

plate until the adapter plate locks in place at the narrow section

of the key holes (Fig. 7).

3. Tighten the two mounting ring screws previously loosened and

the one previously removed to secure adapter plate (Fig. 7).

6. Attaching the Fan Blades

7. Installing the Adapter Plate

FH-W1802 Vox Instructions 19

5

6

7

1. Screw

2. Mounting Bracket

3. Trim Ring

4. Motor

1. Slot

2. Blade

3. Screw with Lock

Washers

1. Mounting Ring

2. Adapter Plate

1

2

3

2

4

1

3

2

1

FH-W1802Vox Instructions20

8. Installing the LED Luminaire Module

WARNING: Before starting installation, disconnect the power

by turning oﬀ the circuit breaker or removing the fuse at fuse box.

1. Remove 3 screws from the outer perimeter of the adapter plate

and keep for future use.

2. Raise and hold the LED luminaire module close to the adapter

plate and proceed to secure the wire connections. Connect the

white wire connectors from the luminaire module to the white

wire of the fan. Connect the blue wire from the fan to the blue

wire from the LED module.

3. Tuck connections neatly into mounting plate. Place the luminaire

module against the adapter plate and secure with the 3 screws

previously removed.

4. Raise glass shade up against the luminaire module, and secure

it to fan by turning acrylic shade clockwise until snug. Do not

overtighten.

La page charge ...

Modern Forms FH-W1802 Vox 38 Mode d'emploi

Ce manuel convient également à

Modern Forms FH-W1802 Vox 38 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents