REOLINK B800W Mode d'emploi

Marque: REOLINK

Modèle: B800W

Taper: Mode d'emploi

Ci-dessous, vous trouverez de brèves informations pour Caméra de surveillance B800W. Ce guide fournit des instructions pour la configuration initiale de la caméra de surveillance, y compris la connexion à l'enregistreur vidéo en réseau (NVR) via Ethernet ou WiFi. Il explique aussi comment utiliser l'application Reolink sur smartphone ou PC pour accéder à la camera. Le guide fournit également des conseils de montage, des informations de dépannage et quelques spécifications du produit.

August 2023

QSG1_A_EN

Quick Start Guide

@ReolinkTech https://reolink.com

58.03.001.0351

Apply to：

B800W

English English1 2

What's in the Box ··················································· 2

Camera Introduction ···············································3

Connection Diagram ···············································4

Access the NVR via Smartphone or PC ······························6

Mount Tips for the Camera ·········································7

Troubleshooting ···················································· 8

Specication ·······················································9

Notication of Compliance ·········································9

What's in the Box

Contents

Waterproof Lid

Bullet Camera

Mounting Hole

Template

1m Ethernet

Cable

Camera Power

Adapter

Surveillance

Sticker

Quick Start

Guide

Pack of

Screws

Power Extension

Cable

English English3 4

Connection Diagram

1.Connect the included power adapter to the NVR and a power outlet.

2.Connect the NVR to your router with an Ethernet cable (if you hope

to use it remotely).

Next, connect the mouse to the USB port of the NVR.

3.Connect the NVR to the monitor with a VGA or HDMI cable.

NOTE: There is no VGA cable and monitor included in the package.

HDMI

VGA

NVR

Router

Camera Introduction

11 12

Antenna

Mount

Metal Aluminum Case

Spotlight

IRLEDs

High Denition Lens

Network Port

Daylight Sensor

Reset Button

Built-in Mic

Power Port

Speaker

* Press for about 10

seconds to restore the

device to factory

settings.

English English5 6

4.Follow the steps on the monitor to complete the initial setup.

NOTE: In the second step, UID is disabled by default. You’re

recommended to enable it for remote access on smartphones or

computers. Or you can set it later in “Settings > System >Info”.

5.Power on your WiFi Cameras and connect them to the LAN ports

(for IPC) on the NVR via Ethernet cables.

6.Click Sync WiFi Info to connect the cameras to the NVR’s WiFi.

7.After the sychronization succeeded, remove the Ethernet cables

and wait for a few seconds for them to be reconnected wirelessly.

installedatthedesiredlocation.

NOTE: There is no NVR included in the package.

8.Afterthewirelessconnectionissuccessful,thecameracanbe

Sync Wi-Fi info

NVR

Router

• On Smartphone

Scan to download the Reolink App.

• On PC

Download path: Go to https://reolink.com > Support > App & Client.

1. Connect the NVR to a router using the included Ethernet cable.

2.Download and launch the Reolink App or Client and follow the

instructions to access the NVR.

Access the NVR via Smartphone or PC

English English7 8

Mount Tips for the Camera

• Do not face the camera towards any light sources.

• Do not point the camera towards a glass window. Or, it may result in

poor image quality because of the window glare by infrared LEDs,

ambient lights or status lights.

• Do not place the camera in a shaded area and point it towards a

well-lit area. Or, it may result in poor image quality. To ensure best image

quality, the lighting condition for both the camera and the capture object

shall be the same.

• To ensure better image quality, it’s recommended to clean the lens with

a soft cloth from time to time.

• Make sure the power ports are not directly exposed to water or

moisture and not blocked by dirt or other elements.

• With IP waterproof ratings, the camera can work properly under

conditions like rain and snow. However, it doesn't mean the camera can

work underwater.

• Do not install the camera at places where rain and snow can hit the lens

directly.

• The camera may work in extreme cold conditions as low as -10°C.

Because when it is powered on, the camera will produce heat. You may

power on the camera indoors for a few minutes before installing it

outdoors.

Installation Tips

NOTE: Please install the cameras within the NVR’s signal range.

Troubleshooting

Solutions:

• Cover the camera’s IR LEDs to see if they light up.

• lf you have a 12V power adapter, power up the camera with the power

adapter.

Cause 1：Camera is not Powering on

Solution:

the correct password for the camera. lf you forget your password, please

reset your camera to reset the password to default (blank).

Solution:

GotoSettings> Channelpage, clickthechannelyouwant, andthense-

lectyour cameraforthatchannel.If all channels are already in use,

please delete the oine camera from the NVR. Then the channel this

camera was taken is free now.

Camera Not Displaying lmages on the Monitor

Cause 2：Incorrect Account Name or Password

Cause 3：Camera is not Assigned to a Channel

English English9 10

Solutions:

• Connect the camera to the NVR with an Ethernet cable. Go to Network

> Wi-Fi > Settings on the monitor to sync the NVR’s WiFi.

• Install the camera within the NVR’s signal range.

• Install antennas on the camera and the NVR.

If these won‘t work, please contact Reolink

Support https://support.reolink.com

Cause 4：No WiFi After Removing the Ethernet Cable

Specication

Operating Temperature:

-10°C to 55°C (14°F to 131°F)

Operating Humidity: 10%-90%

B800W Size: Φ67 x 187mm

Weight: 485.7g, for B800W

For more Specications, visit https://reolink.com/.

Camera

Notication of Compliance

FCC Compliance Statements

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

English English11 12

Caution: Changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

This equipment complies with FCC radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and

operated with minimum distance 20cm between the radiator and your

body.

This device contains licence-exempt transmitter(s)/receiver(s) that

comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two

conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that

may cause undesired operation of the device.

L’ émetteur/récepteur exempt de licence contenu dans le présent

appareil est conforme aux CNR d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence.

L’ exploitation est autorisée aux deux conditions suivantes :

(1) L’ appareil ne doit pas produire de brouillage;

(2) L’ appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d’en compromettre le fonctionnement.

FCC Radiation Exposure statement

ISED Compliance Statements

ISED Radiation Exposure statement

WiFi Operating Frequency

This equipment complies with IC RSS-102 radiation exposure limits set

forth for an uncontrolled environment. This equipment should be installed

and operated with minimum distance 20 cm between the radiator and

your body.

Cet équipement est conforme aux limites d’exposition aux radiations IC

CNR-102 établies pour un environnement non contrôlé. Cet équipement

doit être installé et utilisé avec une distance minimale de 20 cm entre

le radiateur et votre corps. Cet émetteur ne doit pas être colocalisé ou

fonctionner en conjonction avec une autre antenne ou un autre émetteur.

Operation of 5150-5250 MHz is restricted to indoor use only.

Le fonctionnement de 5150-5250 MHz est limité à une utilisation en

intérieur uniquement.

OPERATING FREQUENCY :

2.4 GHzEIRP< 20dBm 5 GHzEIRP< 20dBm 5.8GHz EIRP< 14dBm

Reolink declares that this device is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU and

Directive 2014/30/EU.

Simplied EU Declaration of Conformity

The functions of Wireless Access Systems including Radio Local

Area Networks(WAS/RLANs) within the band 5150-5350 MHz for

this device are restricted to indoor use only within all European

English13

UKCA Declaration of Conformity

Reolink declares that this product is in compliance with Electromagnetic

Compatibility Regulations 2016 and Electrical Equipment Safety

Regulations 2016.

Union countries (BE/BG/CZ/DK/DE/EE/IE/EL/ES/FR/HR/ IT/CY/LV/LT/

LU/HU/MT/NL/AT/PL/PT/RO/SI/SK/FI/SE/TR/N O/CH/IS/LI/UK(NI)

This marking indicates that this product should not be disposed with other

household wastes.throughout the EU. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, recycle

it responsibly to promote the sustainable reuse of material resources. To

return your used device, please use the return and collection systems or

contact the retailer where the product was purchased. They can take this

product for environmentally safe recycling.

Correct Disposal of This Product

This product comes with a 2-year limited warranty that is valid only if

purchased from Reolink Ocial Store or a Reolink authorized reseller.

Learn more: https://reolink.com/warranty-and-return/.

Limited Warranty

Use of the product is subject to your agreement to the Terms of Service

and Privacy Policy at reolink.com. Keep out of reach of children.

Terms and Privacy

REOLINK B800W Mode d'emploi

Marque: REOLINK

Modèle: B800W

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: REOLINK B800W User guide

REOLINK B800W Mode d'emploi

REOLINK B800W Mode d'emploi

dans d''autres langues

Documents connexes