Mist AP33 Guide d'installation

Marque: Mist

Modèle: AP33

Taper: Guide d'installation

AP33 or AP32 Hardware Installation Guide

AP33 and AP32 Hardware Installation Guide

Overview

The Mist AP33 and AP32 contains three IEEE 802.11ax radios that deliver up

to 4x4 MIMO with four spatial streams when operating in multi-user (MU) or

single-user (SU) mode.

AP33 or AP32 Hardware Installation Guide

I/O ports

Reset Reset to the factory default settings

USB USB2.0 support interface

Eth1 10/100/1000BASE-T RJ45 interface

Eth0+PoE 100/1000/2500BASE-T RJ45 interface that supports

802.3at PoE PD

AP33 or AP32 Hardware Installation Guide

AP33/32 Mounting

In a wall mount installation, please use screws that have a 1/4in. (6.3mm) diameter head with a

length at least 2 in. (50.8mm).

AP33 or AP32 Hardware Installation Guide

The bracket attaches to a rod that is 5/8”-11.

The bracket attaches to a rod that is M16-2.

AP33 or AP32 Hardware Installation Guide

Technical Specifications:

Feature Description

Power options 802.3at/802.3af PoE

Dimensions 202mm x 202mm x 44mm (7.95in x 7.95in x 1.73in)

Weight

AP33: 0.98 kg (2.16 lbs)

AP32: 0.83 kg (1.83 lbs)

AP32E: 0.81 kg (1.78 lbs)

Operating

temperature

AP33: -5° to 40° C

AP32: -5° to 40° C

AP32E: -5° to 40° C

Operating humidity 10% to 90% maximum relative humidity, non-condensing

Operating altitude 3,048m (10,000 ft)

I/O

1 – 100/1000/2500BASE-T auto-sensing RJ-45 with PoE

1 – 10/100/1000BASE-T auto-sensing RJ-45

1 – USB2.0

5GHz - 4x4:4SS 802.11ax MU-MIMO & SU-MIMO

2.4GHz – 2x2:2SS 802.11ax MU-MIMO & SU-MIMO

2.4GHz / 5GHz scanning radio

AP33 - 2.4GHz BLE with Dynamic Antenna Array

AP32/AP32E - 2.4GHz BLE with Omni Antenna

Maximum PHY rate

Total maximum PHY rate – 2974 Mbps

5GHz – 2400 Mbps

2.4GHz – 574Mbps

Indicators Multi-color status LED

Compliance standards

CAN/CSA-C22.2 No. 62368-1-14

UL 2043

FCC Part 15.247, 15.407, 15.107, and 15.109

RSS-247

ICES-003 (Canada)

Suitable for use in environmental air space in accordance with Section 300-22(C) of the

National Electrical Code, and Sections 2-128, 12-010(3), and 12-100 of the Canadian

Electrical Code, Part 1, CSA C22.1.

Warning: The AP must be mounted only horizontally if you mount it into a plenum space.

AP33 or AP32 Hardware Installation Guide

Warranty Information

The AP33 or AP32 family of Access Points comes with a limited lifetime warranty.

Ordering Information:

Access Points

AP33-US 802.11ax WiFi and BLE Array AP - Internal Antenna for

the US Regulatory domain

AP33-WW 802.11ax WiFi and BLE Array AP – Internal Antenna for

the WW Regulatory domain

AP32-US 802.11ax WiFi and BLE AP – Internal Antenna for the US

Regulatory domain

AP32-WW 802.11ax WiFi and BLE AP – Internal Antenna for the

WW Regulatory domain

AP32E-US

802.11ax WiFi and BLE AP

–

ternal Antenna

for the

US Regulatory domain

AP32E-WW

802.11ax WiFi and BLE AP

–

ternal Antenna

for the

WW Regulatory domain

Mounting brackets

APBR

Universal AP Bracket for T

Rail and Drywall mounting

for Indoor Access Points

APBR-T58

5/8-inch threaded rod bracket

APBR-M16

16mm threaded

rod

bracket

APBR-ADP-CR9

Adapter for channel rail and recessed 9/16” t

rail

APBR-ADP-RT15

Adapter for recessed

15/16"

rail

APBR-ADP-WS15

Adapter for recessed

rail

APBR-ADP-T12

Adapter for

1/2

inch thread

rod

AP33 or AP32 Hardware Installation Guide

Regulatory Compliance Information:

This product and all interconnected equipment must be installed indoors within the same

building, including the associated LAN connections as defined by the 802.3at Standard.

Professional installation instructions

● Installation personnel – This product is designed for a specific application and needs

to be installed by qualified personnel who have RF and related rule knowledge. The

general user shall not attempt to install or change the settings.

● Installation location – The product shall be installed at a location where the radiating

antenna can be kept 44cm(FCC) or 48cm(IC) from nearby personnel in normal

operating conditions to meet the regulatory RF exposure requirement.

● External antenna – Use only an antenna which has been approved by Juniper. The

non-approved antenna(s) may produce unwanted spurious emissions or excessive RF

transmitting power which could violate the FCC limits.

● Installation procedure – Please refer to top section of this installation guide for

detailed instructions.

● Warning – Please carefully select the installation position and make sure that the

final output power does not exceed the limit set in the relevant rules. The violation

of the rule could lead to a federal penalty.

Instructions d'installation professionnelles

 Personnel d'installation - Ce produit est conçu pour une application spécifique et doit

être installé par du personnel qualifié ayant des connaissances en RF et en règles

associées. L'utilisateur général ne doit pas tenter d'installer ou de modifier les

paramètres.

 Emplacement d'installation - Le produit doit être installé à un endroit où l'antenne

rayonnante peut être maintenue à 44 cm (FCC) ou 48 cm (IC) du personnel à

proximité dans des conditions de fonctionnement normales pour répondre aux

exigences réglementaires d'exposition aux RF.

 Antenne externe - Utilisez uniquement une antenne approuvée par Juniper. Les

antennes non approuvées peuvent produire des émissions parasites indésirables ou

une puissance de transmission RF excessive qui pourraient enfreindre les limites de

la FCC.

 Procédure d'installation - Veuillez vous référer à la section supérieure de ce guide

d'installation pour des instructions détaillées.

 Avertissement - Veuillez sélectionner soigneusement la position d'installation et

assurez-vous que la puissance de sortie finale ne dépasse pas la limite définie dans

les règles pertinentes. La violation de la règle pourrait entraîner une sanction

fédérale.

If you need further assistance with purchasing the power source, please contact Juniper

Networks, Inc.

AP33 or AP32 Hardware Installation Guide

FCC Requirement for Operation in the United States of

America:

FCC Guideline for Human Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 44

cm between the radiator & your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

● Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

● This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

AP33 or AP32 Hardware Installation Guide

Industry Canada

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux appareils

radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1)

le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit

accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un

fonctionnement indésirable.

This radio transmitter (IC: 22068-AP33 / Model: AP32E, AP32, AP33) has been approved

by ISED to operate with the antenna type listed below with maximum permissible gain

indicated. Antenna types not included in this list, having a gain greater than the maximum

gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio (IC: 22068-AP33 / Model: AP32E, AP32, AP33) a été approuvé

par ISED pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain

admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est

supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de

l'émetteur.

Approved antenna(s) list:

Antenna No. Brand Model Antenna Net

Gain (dBi)

Frequency

range (GHz) Antenna Type Connector

Type

Ext WiFi Dual

Ant

Acceltex

ATS

245

6RPSP-36 4

2.4 – 2.484

5.15 – 5.85 Omnidirectional RPSMA Plug

Ext WiFi Dual

Ant

Acceltex

ATS

245

810

4RPSP-36

10 2.4 – 2.484

5.15 – 5.85 Directional RPSMA Plug

Int WiFi Dual

Ant

2.4 – 2.484

5.15 – 5.85 Omnidirectional N/A

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 48

cm between the radiator & your body.

Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites

d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec un minimum de 48 cm de distance entre la

source de rayonnement et votre corps.

AP33 or AP32 Hardware Installation Guide

IC Caution

(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce

the potential for harmful interference to co-channel mobile satellite systems;

(ii) The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and

5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be

such that the equipment still complies with the e.i.r.p. limits specified for point-to-point

and non-point-to-point operation as appropriate; and

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these

radars could cause interference and/or damage to LE-LAN devices.

Avertissement

Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions

précises sur les restrictions susmentionnées, notamment :

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement

pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5

350 MHz et de 5470 à 5725 MHz doit être conforme à la limite de la p.i.r.e;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5

850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à

point et l’exploitation non point à point, selon le cas;

(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de

haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour

les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du

brouillage et/ou des dommages aux dispositifs LAN-EL.

Mist AP33 Guide d'installation

Marque: Mist

Modèle: AP33

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Mist AP33 Installation guide

Mist AP33 Guide d'installation

Mist AP33 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents