Astria Fireplaces Allume ST Mode d'emploi

Marque: Astria Fireplaces

Modèle: Allume ST

Catégorie: Poêles

Taper: Mode d'emploi

Ce manuel convient également à

Allume

Installation and Operation Instructions

Direct-Vent Linear Gas Fireplace

Models

ALLUME60TEN

P/N 900909-00 Rev B 10/2019

Report No. F11 -026

PFS

USC

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inﬂammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualiﬁé

ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or

mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated

on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements

locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque

signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 900909-01.

P900909-00

NOTE: DIAGRAMS AND ILLUSTRATIONS THROUGHOUT THE MANUAL ARE NOT TO SCALE.

Astria.us.com 900909-00_B2

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is pro-

vided with this appliance and must be installed for the protection of children and

other at-risk individuals.

DANGER

PELIGRO

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de

contact accidentel avec la vitre chaude et doit être installé pour la protection Des

enfants et Des personnes à risques.

Vea el volante adjunto para la representación de color adecuado

See attached color ﬂyer for proper color representation

Voir ci-joint tract pour une bonne représentation de la couleur

SAFETY AND YOUR FIREPLACE

Se provee con este aparato una barrera de protección (malla), diseñada para reducir

el riesgo de quemaduras por contacto accidental con el vidrio caliente que debe estar

instalada para protección de infantes y otros individuos en riesgo.

Astria.us.com900909-00_B 3

 Aﬁn d’éviter les brûlures

graves ou les blessures,

ne pas retirer l’écran de

protection de la foyer qui

empêche tout contact

direct avec la vitre.

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous

les membres de votre famille soient

conscients du danger de brûlure

encouru :

• Les surfaces de votre foyer deviennent

EXTRÊMEMENT CHAUDES !

• La vitre située à l'avant du foyer atteint

des températures EXTRÊMEMENT

ÉLEVÉES et peut causer de graves

blessures en cas de contact.

• Tenez les enfants à l'écart du foyer

lorsqu'il fonctionne. Surveillez

attentivement les enfants dans les

pièces où un foyer est utilisé aﬁn

d'éviter qu'ils ne soient en contact avec

la vitre.

• Tenez tous les vêtements, les meubles,

l'essence et tout autre liquide

inﬂammable à l'écart du foyer.

• Même après fermeture du gaz, les

surfaces du foyer restent extrêmement

chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité

d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous

les utilisateurs les dangers liés aux

températures élevées

(Pages 41)



Lisez L’information de sûreté

importante (Page 4)

Para evitar quemaduras y lesiones

graves, no quite el protector de malla

o guardia de seguridad que evita el

contacto directo con el vidrio.

 Siga las instrucciones de seguridad

a continuación y asegúrese de que

todos en su hogar sepan acerca de este

peligro de quemadura:

• ¡Las superﬁcies de la chimenea se

ponen MUY CALIENTES!

• El vidrio delante de la

chimenea alcanza temperaturas

EXTREMADAMENTE ALTAS y puede

causar quemaduras graves si se toca.

• Mantenga a los niños alejados de

la chimenea en funcionamiento.

Supervise en forma cercana a los niños

en cualquier cuarto donde haya una

chimenea funcionando para impedir el

contacto con el vidrio.

• Mantenga la ropa, mobiliario, gasolina

y otros líquidos inﬂamables alejados

de la chimenea.

• Aún después de haber apagado el

gas, las superﬁcies de la chimenea

permanecen extremadamente

calientes.

 Asegúrese de colocar las Etiquetas de

advertencia de seguridad de operación

en el lugar donde enciende la chimenea,

para que todos recuerden los peligros

asociados con las altas temperaturas

(Página 41)



Lea Información importante de

seguridad (Página 4).

Seguridad y su

chimenea

La sécurité et

votre foyer

[FRENCH][ENGLISH] [SPANISH]

Safety and Your

Fireplace

 To prevent severe burns

and injuries, do Not

remove the barrier on the

appliance which prevents

direct contact with the

glass.

 Follow the safety instructions below

and be sure everyone in your household

understands this burn hazard:

• The surfaces on your ﬁreplace get

EXTREMELY HOT!

• The glass on the front of the

ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe

burns if touched.

• Keep children away from an operating

ﬁreplace. Closely supervise children

in any room where a ﬁreplace is

operating to prevent contact with glass.

• Keep clothing, furniture, gasoline, and

other ﬂammable liquids away from the

ﬁreplace.

• Even after the gas is turned off,

ﬁreplace surfaces remain extremely

hot.

 Be sure to attach the enclosed Safety-

in-Operation Warnings where you

turn on your ﬁreplace, to help remind

everyone of the dangers associated with

high temperatures

(Pages 41)

 Read Important Safety Information

(Page 4)

All parts of your

IHP ﬁreplace get

EXTREMELY HOT!

Toutes les parties de votre

foyer IHP deviennent

EXTRÊMEMENT CHAUDES !

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

Astria.us.com 900909-00_B4

Important Safety Information

1. WARNING: Do not operate appliance

with the glass front removed, cracked,

or broken.

2. Do not use this appliance if any part

has been under water. Immediately

call a qualiﬁed service technician to in-

spect the appliance and to replace any

part of the control system and any gas

control which has been under water.

3. Due to high temperatures, the appli-

ance should be located out of trafﬁc

and away from furniture and draperies.

4. Children and adults should be alerted

to the hazards of high surface tem-

perature and should stay away to avoid

burns or clothing ignition.

5. Clothing or other ﬂammable material

should not be placed on or near the

appliance.

6. Young children should be carefully

supervised when they are in the same

room as the appliance. Toddlers,

young children, and others may be sus-

ceptible to accidental contact burns.

A physical barrier is recommended

if there are at-risk individuals in the

house. To restrict access to a ﬁreplace

or stove, install an adjustable safety

gate to keep toddlers, young children,

and other at-risk individuals out of the

room and away from hot surfaces.

7. Any safety screen, guard or barrier

removed for servicing an appliance

must be replaced prior to operating

the appliance.

8. Installation and repair should be done

by a qualiﬁed service person. The ap-

pliance should be inspected before use

and at least annually by a professional

service person. More frequent clean-

ing may be required due to excessive

lint from carpeting, bedding material,

et cetera. It is imperative that control

compartments, burners, and circulat-

ing air passageways of the appliance

be kept clean. See maintenance in-

structions on Page 48.

L’information de sûreté

importante

1. AVERTISSEMENT. Ne pas utiliser l’appareil

si le panneau frontal en verre n’est pas en

place, est craqué ou brisé.

2. Ne pas se servir de cet appareil s’il a été

plongé dans l’eau, même partiellement.

Faire inspecter l'appareil par un technicien

qualiﬁé et remplacer toute partie du systéme

de contrôle et toute commande qui ont été

plongées dans l'eau.

3. En raison des températures élevées,

l’appareil devrait être installé dans un en-

droit où il y a peu de circulation et loin du

mobilier et des tentures.

4. Les enfants et les adultes devraient être

informés des dangers que posent les tem-

pératures de surface élevées et se tenir à

distance aﬁn d’éviter des brûlures ou que

leurs vêtements ne s’enﬂamment.

5. On ne devrait pas placer de vêtements

ni d’autres matières inflammables sur

l’appareil ni à proximité.

6. Les jeunes enfants devraient être surveillés

étroitement lorsqu’ils se trouvent dans la

même pièce que l’appareil. Les tout petits,

les jeunes enfants ou les adultes peuvent

subir des brûlures s’ils viennent en contact

avec la surface chaude. Il est recommandé

d’installer une barrière physique si des

personnes à risques habitent la maison.

Pour empêcher l’accès à un foyer ou à un

poêle, installez une barrière de sécurité

; cette mesure empêchera les tout petits,

les jeunes enfants et toute autre personne

à risque d’avoir accès à la pièce et aux

surfaces chaudes.

7. Tout écran ou protecteur retiré pour per-

mettre l’entretien de l’appareil doit être

remis en place avant de mettre l’appareil

en marche.

8. L’installation et la réparation devrait être

conﬁées à un technicien qualiﬁé. L’appareil

devrait faire l’objet d’une inspection par un

technicien professionnel avant d’être utilisé

et au moins une fois l’an par la suite. Des

nettoyages plus fréquents peuvent être

nécessaires si les tapis, la literie, et cetera

produisent une quantité importante de pous-

sière. Il est essentiel que les compartiments

abritant les commandes, les brûleurs et les

conduits de circulation d’air de l’appareil

soient tenus propres. Voyez les instructions

d’entretien à la page 48.

Información importante de

seguridad

1. ADVERTENCIA: No opere el artefacto con el

frente de vidrio quitado, agrietado o roto.

2. No use este artefacto si alguna de sus partes

ha estado bajo agua. Llame de inmediato

a un técnico de servicio caliﬁcado para

que inspeccione el artefacto y reemplace

cualquier parte del sistema de control y

cualquier control de gas que haya estado

bajo agua.

3. Debido a las altas temperaturas, el artefacto

debe situarse fuera de las áreas de tráﬁco y

lejos del mobiliario y cortinas.

4. Se debe alertar a los niños y adultos sobre

los peligros de las altas temperaturas en la

superﬁcie y que se mantengan alejados para

evitar quemaduras o ignición de la ropa.

5. No debe colocarse ropa u otros materiales

inﬂamables sobre y cerca del artefacto.

6. Se debe supervisar de cerca a los niños

cuando estén en el mismo cuarto que el

artefacto. Los niños pequeños, los jóvenes

y otras personas pueden ser susceptibles

a quemaduras por contacto accidental. Se

recomienda instalar una barrera física si hay

personas en riesgo en la casa. Para restringir

el acceso a una chimenea o estufa, instale

una puerta de seguridad ajustable para

mantener a los niños pequeños, jóvenes y

otras personas en riesgo fuera del cuarto y

lejos de las superﬁcies calientes.

7. Cualquier malla o resguardo de seguridad

quitado para dar servicio a un artefacto, debe

reinstalarse antes de operar el artefacto.

8. Una persona de servicio competente debe

realizar la instalación y reparación. Una

persona de servicio profesional debe

inspeccionar el artefacto antes de usar al

menos una vez por año. Se puede requerir

limpieza más frecuente debido a la pelusa

excesiva del alfombrado, del material de

cobijas, etc. Es imprescindible mantener

limpios los compartimientos de control, los

quemadores y los pasajes de circulación del

aire del artefacto. Ver las instrucciones de

mantenimiento en la página 48.

IMPORTANT SAFETY INFORMATION

Astria.us.com900909-00_B 5

Safety and Your Fireplace .............................................................. 2

Important Safety Information ........................................................ 4

Installation Checklist ..................................................................... 6

Safety ............................................................................................ 7

Local Codes .................................................................................. 9

Product Features ........................................................................... 9

Packaging ..................................................................................... 9

Product Identiﬁcation .................................................................. 10

Requirements for the Commonwealth of Massachusetts ........... 10

Cold Climate Insulation ............................................................... 10

High Altitude Requirements ........................................................ 11

Manufacturing Requirements ...................................................... 11

Typical Locations ........................................................................ 11

Installing TV above Fireplace ....................................................... 12

Pre-installation ............................................................................ 13

Termination Location and Clearances.......................................... 18

Venting Installation ..................................................................... 19

Thank you for your purchase. We appreciate your business!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information.

Following these safety, care, and operation instructions will help ensure many years of dependable and enjoyable service from your ﬁreplace.

Please read and understand these instructions before installing or operating.

TABLE OF CONTENTS

Fireplace Installation ....................................................................28

Finishing Fireplace .......................................................................35

Attaching Safety Operation Warnings ..........................................38

Operation .....................................................................................39

Cleaning and Maintenance ...........................................................48

Maintenance Schedule .................................................................50

Wiring Diagram ............................................................................51

Gas Conversion Kits .....................................................................52

Speciﬁcations ...............................................................................53

Troubleshooting ...........................................................................54

Technical Service .........................................................................55

Replacement Parts .......................................................................55

Service Hints ................................................................................ 55

Parts ............................................................................................56

Optional Accessories ....................................................................60

Warranty ......................................................................................63

Astria.us.com 900909-00_B6

Installation Checklist

ATTENTION INSTALLER:

Follow this checklist

This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained within this

installation manual.

Customer:

Install address:

Model:

Date Installed:

Location of Fireplace:

Installer:

Dealer Phone:

Serial Number:

YES NO IF NO, REASON

Appliance Install

Framing complies with install manual.

Standoffs, cement boards and support ﬂange have been installed and secured properly

Proper clearances have been maintained.

HeatFlo Kit Installation

All Clearances to pipes and ﬁreplace is maintained as per manual

Veriﬁed that the TV manufacturer’s recommendations are met (TV ambient operating

temperature, clearance to heat sources etc.)

Venting

Venting conﬁguration complies with vent diagrams.

Venting installed, fastened, and secured in place maintaining proper clearance.

Firestops installed.

Exterior wall/roof ﬂashing installed and sealed in compliance with local building code.

Terminations installed and sealed in compliance with local building code.

Direct vent termination is highest point in vent assembly.

Wiring/Electrical

Unswitched power provided to the appliance Junction box.

Gas

Proper appliance for fuel type.

Was a conversion performed?

Leak check performed & inlet pressure veriﬁed.

Finishing

Supplied non-combustible board is installed (do not substitute with another material)

Clearances meet installation manual requirements

Mantels and/or projections comply with install manual

Appliance Setup

Media, door, and screen installed according to install manual

Manual given to home owner.

Started appliance and veriﬁed no gas leaks exist.

Reviewed the safety instruction and lighting instructions with homeowner/builder

representative

Additional Comments:

Astria.us.com900909-00_B 7

WARNING

Do not slam or strike glass doors. Damage can

result in a hazardous condition.

CAUTION

Hot while in operation. Do not touch. Severe Burns may

result. Keep children, clothing furniture, gasoline and

other liquids having ﬂammable vapors away.

Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children and others may be

susceptible to accidental burns.A physical barrier

is recommended if there are at-risk individuals in

the house. To restrict access to a ﬁreplace or stove,

install an adjustable safety gate to keep toddlers,

young children and other at-risk individuals out of

the room and away from hot surfaces.

ATTENTION

L’appareil est chaud lorsqu’il fonctionne. Ne pas

toucher l’appareil. Risque de brûlures graves.

Surveiller les enfants. Garder les vêtements, les

meubles, l’essence ou autres liquides produisant

des vapeur inﬂammables loin de l’appareil.

SAFETY

WARNING

Improper installation, adjustment, alteration,

service or maintenance can cause injury or property

damage. Refer to this manual. For assistance or

additional information consult a qualiﬁed installer,

service agency or the gas supplier.

AVERTISSEMENT

Une installation, un réglage,une modiﬁcation,

une réparation ou un entretien mal effectué peut

causer des dommages matériels ou des blessures.

Voir la notice de l’utilisateur qui accompagne

l’appareil. Pour de l’aide ou des renseignements

supplémentaires, consultez un installateur, un

technicien agréé ou le fournisseur de gaz.

IMPORTANT

Read this owner’s manual carefully and completely

before trying to assemble, operate or service this

ﬁreplace. Improper use of this ﬁreplace can cause

serious injury or death from burns, ﬁre, explosion,

electrical shock and carbon monoxide poisoning.

WARNING

This product can expose you to chemicals including

Carbon Black, which is known to the State of Califor-

nia to cause cancer, and Carbon Monoxide, which is

known to the State of California to cause birth defects

or other reproductive harm. For more information go

to www.P65Warnings.ca.gov

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certiﬁed kit is used.

State of Massachusetts: The installation must be

made by a licensed plumber or gas ﬁtter in the

Commonwealth of Massachusetts.

AVERTISSEMENT

Ce produit peut vous exposer à des produits chimiques,

y compris du carbone noir qui est reconnu par l'État

de Californie comme un produit cancérigène, et du

monoxyde de carbone, qui est reconnu par l'État de

Californie comme pouvant causer des déformations

fœtales ou perturber la fonction reproductive. Pour plus

d’information, aller sur www.P65Warnings.ca.gov

WARNING

Never connect this appliance to private (non-

utility) gas wells. This gas is commonly known as

wellhead gas and does not have odorants and may

have impurities, and variations in BTU content. The

use of well-head gas will void the manufacturer’s

warranty to this appliance.

Astria.us.com 900909-00_B8

SAFETY Continued

WARNING

Any change to this ﬁreplace or its controls can be

dangerous. Do not modify this ﬁreplace under any

circumstances. Any parts removed for servicing

must be replaced prior to operating ﬁreplace.

WARNING

Do not use a blower insert, heat exchanger insert

or other accessory not approved for use with this

ﬁreplace.

WARNING

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases unless a

certiﬁed kit is used.

WARNING

Do not allow fans to blow directly into the ﬁreplace.

Avoid any drafts that alter burner ﬂame patterns.

Due to high temperatures, the appliance should be

located out of trafﬁc and away from furniture and

draperies.

Do not place clothing or other ﬂammable material

on or near the appliance. Never place any objects

on the appliance.

Do not use this ﬁreplace to cook food or burn paper

or other ﬂammable material.

DANGER

Carbon monoxide poisoning may lead to death!.

Carbon Monoxide Poisoning: Early signs of carbon monoxide poison-

ing resemble the ﬂu, with headaches, dizziness or nausea. If you have

these signs, the ﬁreplace may not be working properly. Get fresh air

at once! Have ﬁreplace serviced. Some people are more affected by

carbon monoxide than others. These include pregnant women, people

with heart or lung disease or anemia, those under the inﬂuence of

alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and propane/LP gas are odor-

less. An odor-making agent is added to the gas. The odor helps you

detect a gas leak. However, the odor added to the gas can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this

manual for reference. It is your guide to safe and proper operation

of this ﬁreplace.

Carefully supervise young children when they are

in the room with ﬁreplace.

Keep the area around your ﬁreplace clear of com-

bustible materials, gasoline and other ﬂammable

vapor or liquids. Do not run ﬁreplace where these

are used or stored.

This ﬁreplace reaches high temperatures. Keep chil-

dren and adults away from hot surface to avoid burns

or clothing ignition. Fireplace will remain hot for a time

after shutdown. Allow surface to cool before touching.

1. For propane/LP ﬁreplace, do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP supply tank(s) outdoors.

To prevent performance problems, do not use propane/LP fuel

tank of less than 100 lb. capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in your

building

• leave the building immediately

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier's instructions

• if you cannot reach your gas supplier, call the ﬁre department.

3. Never install the ﬁreplace

• in a recreational vehicle

• in windy or drafty areas where curtains or other combustible

(ﬂammable) objects can make contact with the ﬁreplace front

• in high trafﬁc areas

4. Turn ﬁreplace off and let cool before servicing, installing or

repairing. Only a qualiﬁed service person should install, service

or repair this ﬁreplace. Have ﬁreplace inspected annually by a

qualiﬁed service person.

These vented gas ﬁreplace heaters are sealed combustion, air-

circulating gas ﬁreplaces designed for residential, manufactured

home, and commercial applications. Direct-vent appliances

operate with the combustion chamber isolated from the indoor

environment. All air for combustion is brought in from the outside,

and exhaust gases are vented through the same direct-vent, coaxial

(intake/exhaust) vent system. These ﬁreplaces must be installed

with Metal-Fab Sure-Seal Direct Vent Pipe components and

terminations.

This ﬁreplace must be installed by a qualiﬁed (certiﬁed or licensed)

service person. It brings in fresh air for combustion through the outer

pipe and combustion gases are exhausted through the inner pipe. If

the glass door assembly and venting pipe are not properly seated,

connected and sealed, carbon monoxide leakage (spillage) can occur.

Astria.us.com900909-00_B 9

SAFETY Continued

LOCAL CODES

Install and use ﬁreplace with care. Follow all local codes. In the ab-

sence to local codes, use the current National Fuel Gas Code ANSI

Z223.1/NFPA 54* (USA) or the current CAN/CGA B149.1 Installation

Code (Canada).

*Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th ﬂoor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

Codes and Standards

Listing: These ﬁreplaces comply with National Safety Standards and

are tested and listed by PFS TECO (Report No. F11-026) to ANSI

Z21.88 (in Canada, CSA-2.33), and CAN/CGA-2.17-M91 (CSA P4.1)

in both USA and Canada, as vented gas ﬁreplace heaters.

These appliances comply with CSA P.4.1-2015 “Testing Method

for Measuring Annual Fireplace Efﬁciency. P4 (EnerGuide) is a

measurement of the Canadian Ofﬁce of Energy Efﬁciency.

These ﬁreplaces are listed for installation in bedrooms, aftermarket

mobile homes, and manufactured homes.

The installation must conform to local codes or, in the absence of

local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA

54—latest edition, or the Natural Gas and Propane Installation

Code, CSA B149.1.

The ﬁreplace, when installed, must be electrically grounded and

wired in accordance with local codes or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA 70—latest

edition, or the Canadian Electrical Code, CSA C22.1—latest edition.

PRODUCT FEATURES

These are a few facts that can help you understand and enjoy your

direct vent ﬁreplace:

• The venting system may be routed to the outside of your home in

several ways. It may vent through the roof (vertical) or it may vent

to an outside/exterior wall (horizontal). The vent pipe installation is

very important to allow for proper operation. You must follow the

venting instructions very carefully for either vertical or horizontal

applications.

• This ﬁreplace may be installed in any room of your house provided

all local codes and these installation instructions are followed.

• Each time you turn on your ﬁreplace, you may notice some amount

of condensation on the inside of the ﬁreplace glass. This is normal

and will disappear after 10-20 minutes of operation.

• Your direct vent ﬁreplace system (ﬁreplace and venting) is a bal-

anced and sealed combustion system. It requires approximately

10-20 minutes of operating time before the ﬂame pattern stabilizes.

PACKAGING

The assembled Direct Vent Gas Fireplace is packaged with:

• Literature Kit (Installation and Operation Instructions (this

manual), Hot Glass Safety Flyer, and Safety-In-Operation Warn-

ing Labels.

• Three (3), 5 lb. bags, Reﬂective Black Glass Media

• One (1), Hand Held Remote Control

• Four (4), AA Batteries

• Three (3), AAA Batteries

• One (1), Latch Opener

• One (1), Fireboard Top

• One (1), Fireboard Bottom

• Two (2), Fireboard Sides

• Forty eight (48) Self Drill Bugle Drywall Screws

5. You must keep control compartments, burners and circulating

air passages clean. More frequent cleaning may be needed due

to excessive lint and dust from carpeting, bedding material, etc.

Turn off the gas valve and pilot light before cleaning ﬁreplace.

6. Have ﬁreplace and venting system inspected annually by a quali-

ﬁed service person. If needed, have venting system cleaned or

repaired. See Cleaning and Maintenance, page 48.

7. Do not use any solid fuels (wood, coal, paper, cardboard, etc.)

in this ﬁreplace. Use only the gas type indicated on ﬁreplace

nameplate.

8. This appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes,

with the National Electrical Code, ANSI/NFPA 70 or Canadian

Electrical Code, CSA C22.1.

9. Do not use ﬁreplace if any part has been exposed to or under

water. Immediately call a qualiﬁed service person to arrange for

replacement of the unit.

10. Do not operate ﬁreplace with glass door removed, cracked or

broken.

11. Provide adequate clearances around air openings.

Astria.us.com 900909-00_B10

PRODUCT IDENTIFICATION

Figure 1 - Direct Vent ALLUME60TEN Fireplace

REQUIREMENTS FOR THE COMMONWEALTH OF

MASSACHUSETTS

These appliances are approved for installation in the U.S. state of

Massachusetts if the following additional requirements are met:

• Install this ﬁreplace in accordance with Massachusetts Rules

and Regulations 248 C.M.R. 4.00 through 8.00.

• Installation and repair must be done by a plumber or gas ﬁtter

licensed in the Commonwealth of Massachusetts.

• The ﬂexible gas line connector used shall not exceed 36” (914

mm) in length.

• The individual manual shutoff must be a T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, horizontal terminations

installed less than seven (7) ft above the ﬁnished grade must

comply with the following additional requirements:

• A hard wired carbon monoxide detector with an alarm and

battery back-up must be installed on the ﬂoor level where the

gas ﬁreplace is installed. The carbon monoxide detector must

comply with NFPA 720, be ANSI/UL 2034 listed and be ISA

certiﬁed.

• A metal or plastic identiﬁcation plate must be permanently

mounted to the exterior of the building at a minimum height

of eight (8) ft above grade and be directly in line with the

horizontal termination. The sign must read, in print size no

less than one-half (1/2) inch in size, GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks around your ﬁreplace

with noncombustible material and wherever cold air could enter

the room. It is especially important to insulate outside chase cavity

between studs and under ﬂoor on which ﬁreplace rests, if ﬂoor

is above ground level. Gas line holes and other openings should

be caulked or stuffed with unfaced ﬁberglass insulation. Caulk the

ﬁrestop only where the pipe penetrates an outside wall, attic, or

other unconditioned space.

Note: Caulking used must have a minimum of 300°F continuous

exposure rating.

NOTE: Do not use loose, or blown-in insulation in the cavity

surrounding the ﬁreplace.

If the ﬁreplace is being installed on a cement slab in cold climates, a

sheet of plywood or other raised platform can be placed underneath

to prevent conduction of cold transferring to the ﬁreplace and into

the room. It also helps to sheetrock inside surfaces and tape for

maximum air tightness and caulk ﬁrestops.

Glass Door

Gas Connection

Access Door

Cover

Barrier

Fireboard

Nailing Flange Nailing Flange

Top Spacers

Flue

Connector

Nailing Flange

Fireplace Top

Spacers

Note: Electrical connection is located on

the left side. Both, gas line connection

and electrical connection may be

interchangeable.

Astria.us.com900909-00_B 11

MANUFACTURED HOME REQUIREMENTS

This appliance may be installed in an aftermarket, permanently

located, manufactured home (USA only) or mobile home, where

not prohibited by local codes.

Cet appareil peut être installé dans une maison préfabriquée

(mobile) déjà installée à demeure si les règlements locaux le

permettent.

This appliance is only for use with the type of gas indicated on the

rating plate. This appliance is not convertible for use with other

gases, unless a certiﬁed kit is used.

Cet appareil doit être utilisé uniquement avec le type de gaz indiqué

sur la plaque signalétique. Cet appareil ne peut être converti à

d’autres gaz, sauf si une trousse de conversion est utilisée.

CAUTION

Ensure that the cross members are not cut or

weakened during installation. The structural

integrity of the manufactured home ﬂoor, wall, and

ceiling / roof must be maintained.

CAUTION

This appliance must be grounded to the chassis of

the manufactured home in accordance with local

codes or in the absence of local codes, with the

National Electrical Code ANSI / NFPA 70—latest

edition or the Canadian Electrical Code CSA C22.1—

latest edition.

TYPICAL LOCATIONS

In selecting the location, the aesthetic and functional use of the

ﬁreplace are primary concerns. However, vent system routing to

the exterior and access to the fuel supply are also important. The

ﬁreplace may be located on or near conventional construction

materials. See Location and Space requirements page 13 for

more information.

Due to high temperatures, the appliance should be located out of

trafﬁc and away from furniture and draperies.

En raison des températures élevées, l’appareil devrait être

installé dans un endroit où il y a peu de circulation et loin du

mobilier et des tentures.

The location should also be free of electrical, plumbing or other

heating/air conditioning ducting.

Be aware that this is a heat producing ﬁreplace. Objects placed

above the unit are exposed to elevated temperatures. Do not

insulate the space between the ﬁreplace and the area above it.

HORIZONTAL VENT

(Rear Vent Application with a chase) HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT (Rear Vent Application without a chase)

HORIZONTAL VENT

Horizontal Vent

(Top Vent)

Vertical Vent

(Top Vent)

HORIZONTAL VENT

(Rear Vent Application with a chase) HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

(Rear Vent Application)

VERTICAL VENT (Rear Vent Application without a chase)

HORIZONTAL VENT

Top Vent

Top Vent Top Vent

Top Vent

Recessed

Installation

Figure 2 - Typical Locations and Venting

HIGH ALTITUDE REQUIREMENTS

Oriﬁce Sizes—Sea Level to High Altitude

These ﬁreplaces are tested and approved for installation at

elevations of 0–4500 ft (0–1372 m) above sea level using the

standard burner oriﬁce sizes (see speciﬁcations table, page 53).

For elevations above 4500 ft, contact your gas supplier or qualiﬁed

service technician.

Deration

At elevations above 4500 ft, the amount of BTU fuel value delivered

must be reduced by either:

• Using gas that has been derated by the gas company.

• Changing the burner oriﬁce to a smaller size as regulated

by the local authorities having jurisdiction and by the (USA)

National Fuel Gas Code NFPA 54/ANSI Z223.1—latest edition

or, in Canada, the CAN/CGA-B149.1 codes—latest edition.

IN CANADA—CAN/CGA-2.17-M91 (HIGH ALTITUDE):

The conversion shall be carried out by a manufacturer’s authorized

representative, in accordance with the requirements of the

manufacturer, provincial or territorial authorities having jurisdiction

and in accordance with the requirements of the can/cga-b149.1 Or

can/cga-b149.2 Installation codes.

Astria.us.com 900909-00_B12

IMPORTANT NOTICE

AN HTFLO-LIN60 (HEATFLO) KIT IS REQUIRED IF INSTALLING

A TV ABOVE THE FIREPLACE.

IMPORTANT NOTICE

Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may negatively

affect the longevity of the television and may negate the warranty. If you do place a television above the ﬁreplace, please be aware

of the large amount of heat generated by the ﬁreplace and consider placing the television above the ﬁreplace at 12” minimum on

a ﬂush wall and at 18" for a recessed installation, to reduce the amount of heat that reaches the television. The homeowner must

understand that IHP does not take responsibility for any negative impact to televisions placed near this ﬁreplace.

INSTALLING TELEVISION (TV) ABOVE FIREPLACE

The following section details two options for installing a television (TV) above Fireplace

TVs should not be used in situations where the actual TV

temperature exceeds the manufacturer’s technical speciﬁcation.

Contact the TV manufacturer directly if you cannot locate this

information or have questions regarding this information.

NOTE: Clearances to TV are provided only for guidance, please

follow TV manufacturer's recommendation for installation.

• Clearances from ﬁreplace and walls including recessed applications

and clearances from the top of the ﬁreplace, the wall behind the

TV and the clearance between the top of the TV and the ceiling.

• Maximum ambient room temperature for combined operation of

the TV and Fireplace

• To assure acceptable temperatures, the TV manufacturer’s

recommendation for temperatures must be checked after

installation of the TV and with the Fireplace operating on high

after 1 hour. The temperature must be below the manufacturer’s

recommendation or the TV must be moved to provide greater

clearances.

See Tables 1 and 2 for TVs Installed above the ﬁreplace:

WIRING NOTE: If running wiring into the enclosure, use thermal

insulating wrap around the wiring. Secure the wiring to protect

from contact with hot surfaces.

WARNING

Ensure clearances to combustibles are maintained

when building a mantel or shelves above the fireplace.

Elevated temperatures on the wall or in the air above

the fireplace can cause melting, discoloration or

damage to decorations, a television (TV) or other

electronic components.

Table 1 - Dimensions for Television (TV) Installed Above

Fireplace (Flush Wall)

(A) TV Above ﬁreplace Opening 12” (305 mm)

(B) TV Below Heat Vent Opening 3” (77 mm)

Television (TV)

Fireplace

Ceiling

Wall

Floor

HeatFlo

Opening

Min. 88-1/2”

(2.250 m)

Max. 20 ft.

(6.096 m)

Table 2 - Dimensions for Television (TV) Installed Above

Fireplace on a Recessed Wall Pocket

(A) TV Above Fireplace Opening 18” (458 mm)

(B) Recess Depth (Maximum) 3-1/2” (89 mm)

Television (TV)

Fireplace

Television (TV)

5-1/2" (410 mm)

HeatFlo Register

Opening

3" Min.

(77 mm)

3" Min.

(77 mm)

3" Min.(77 mm)

Wall

Floor

Ceiling

Min. 88-1/2”

(2.250 m)

Max. 20 ft.

(6.096 m)

Astria.us.com900909-00_B 13

PRE-INSTALLATION

LOCATION AND SPACE REQUIREMENTS

Determine the safest and most efﬁcient location for your direct vent

ﬁreplace. Make sure that rafters and wall studs are not in the way

of the venting system. Choose a location where the heat output is

not affected by drafts, air conditioning ducts, windows or doors. Be

aware of all restrictions and precautions before deciding the exact

location for your ﬁreplace and termination cap.

When deciding the location of your ﬁreplace, follow these rules:

• Do not connect this ﬁreplace venting to a chimney ﬂue serving a

separate solid-fuel burning ﬁreplace or appliance.

• Due to high temperatures, do not locate this ﬁreplace in high trafﬁc

areas, windy or drafty areas or near furniture or draperies.

• Proper clearances must be maintained.

• If your ﬁreplace is to be installed directly on carpeting, vinyl tile or any

combustible material other than wood, it must be installed on a metal

or wood panel extending the full width and depth of the ﬁreplace (see

table 9, page 18).

• If standoff spacers are attached to your ﬁreplace, these spacers

can be placed directly against wall or framing material. See framing

details, pages 14 thru 16.

• When locating termination cap, it is important to observe the

minimum clearances shown in table 10, page 19.

• Do not recess termination cap into a wall or siding.

• You may paint the termination cap with 450º F (232º C) heat-

resistant paint to coordinate with the exterior ﬁnish.

• There must not be any obstruction such as bushes, garden sheds,

fences, decks or utility buildings within 24" from the front of the

termination cap and the front of outside air vent.

• Do not locate termination cap and outside air vent where excessive

snow or ice build up may occur. Be sure to clear vent termination

area after snow falls to prevent accidental blockage of venting

system. When using snow blowers, do not direct snow towards

vent termination area.

CLEARANCES

Minimum clearances to combustibles for the ﬁreplace are as follows:

NOTICE

This ﬁreplace is intended for use as supplemental heat.

Use this ﬁreplace along with your primary heating sys-

tem. Do not install this ﬁreplace as your primary heat

source. If you have a central heating system, you may

run system’s circulating blower while using ﬁreplace.

This will help circulate the heat throughout the house

Table 3 - Minimum Clearances

Back 1” (26 mm) to wrapper

Sides 1” (26 mm) to wrapper

0” (0 mm) to Spacers

Top Spacers 0” (0 mm)

Floor 0” (0 mm)

From Bottom of Unit to Ceiling 96” (2439 mm)

Vent 3” (77 mm)—Top

1” (26 mm)—Sides and Bottom

Front Clearance — clearance immedi-

ately in front of viewing area(s) 36” (914 mm)

(See venting instructions for speciﬁc venting clearances.)

Do not pack with insulation or other materials around the ﬁreplace.

IMPORTANT! TOP STANDOFF SUB-ASSEMBLY MUST BE IN-

STALLED PRIOR TO APPLIANCE INSTALLATION!

1. Identify top standoff sub-assembly packaged on top of appli-

ance during shipping.

2. Using screws provided, attach assembly to forward portion of

appliance top as shown in Figure 3a.

3. Bend nailing ﬂange top spacers as shown in Figure 3a and attach

to ﬁreboard nailing ﬂange with screws provided.

NOTE: If appliance is being upgraded to a see-thru application install

second top standoff sub-assembly to the rear portion of appliance

top as shown in the see-thru kit instructions.

Fireboard Nailing

Flange Top Spacer

Wrapper

Side

Nailing

Flange

Floor

Wrapper

Back

Fireplace

Top

Spacer Venting

Figure 3 - Clearances to combustibles

Figure 3a - Standoff Installation

Glass Door

Gas

Connection

Access

Door

Cover

Fireboard

Nailing Flange Nailing Flange

Top Spacer

Flue

Connector

Nailing

Flange

Fireplace

Top

Spacer

Note: Electrical connection is located on

the left side. Both, gas line connection and

electrical connection may be interchangeable.

Astria.us.com 900909-00_B14

Secure

Nailing

ﬂanges to

Jack Stud

PRE-INSTALLATION Continued

FRAMING AND FINISHING

IMPORTANT! BEFORE YOU BEGIN FRAMING, DETERMINE

WHETHER YOU WILL BE INSTALLING THE FIREPLACE AS A

ONE SIDED APPLICATION OR SEE-THRU APPLICATION. IF

INSTALLING A TV ABOVE THE FIREPLACE, AN HTFLO-LIN60

KIT IS REQUIRED. FOLLOW INSTRUCTIONS INCLUDED

WITH THE KIT AND FRAMING DETAILS IN THIS MANUAL.

ALLUME60TEN ﬁreplace comes as a one sided factory installed. If

you will be using the ﬁreplace for a one sided regular application,

you can install it as is. If you will be upgrading the ﬁreplace to a see-

thru application a conversion kit cat. no. F3779 is required. Follow

instructions included with the kit.

FRAMING, ONE SIDED/SEE-THRU INSTALLATION

Fireplace Framing Standard Installation (Flush Wall)

Fireplace Framing Flush Wall & HeatFlo Kit (For TV Installation)

Fireplace Framing Recessed Wall & HeatFlo Kit (For TV Installation)

Floor Protection

1. Frame the ﬁreplace as illustrated in Tables 4 to 7, pages 14 to

16. All framing details must allow for a minimum clearances to

combustible framing members as shown in Table 3, page 13.

2. Mount the ﬁreplace on the ﬂoor or on a fully supported base

extending the full width and depth of the unit. If installed

on combustible materials, such as carpeting, vinyl tile, or

combustible material other than wood ﬂooring, the appliance

shall be installed on a metal or wood panel extending the full

width and depth of the ﬁreplace.

3. Headers may be in direct contact with the nailing ﬂange top

spacers, maintaining the 20-1/4” clearance to the ﬁreplace top,

but must not be supported by them or notched to ﬁt around them.

All construction above the ﬁreplace must be self-supporting. DO

NOT use the ﬁreplace for structural support. Note: On a recessed

wall pocket installation, discard ﬁreboard nailing ﬂange and

nailing ﬂange top spacers (see Figure 6,page 15). Header may

be in direct contact with the ﬁreplace top spacers maintaining

the 10-1/4” clearance to the ﬁreplace top.

4. Table 4 and Figure 4, shows a typical framing of this ﬁreplace.

Table 5 and Figure 5, page 15 shows framing for HeatFlo kit

installation. Table 6, page 16 shows a recessed framing for

HeatFlo kit installation. All minimum clearances must be met.

Vent pipe needs to maintain 1" clearance. Wood studs may be

notched. Fireboard is provided for facing around the ﬁreplace.

5. If you are using a separate combustible mantel piece, refer to

table 19, page 35 for proper installation height. You can install

noncombustible mantel.

NOTE: Fireplace is designed for 1/2” thickness of non-combus-

tible ﬁreboard on the face of the unit (Included with one sided

application). If installing a two sided application, the non-com-

bustible ﬁreboard will be included with the see-thru conversion

kit, see accessories page 61).

Figure 4 - Framing Flush wall (Standard Installation)

Secure

Fireboard Nailing

Flange(Front and

Inside of Jack Stud

Fireplace Framing Standard Installation (Flush Wall)

Table 4 - Framing Dimensions Standard Installation - Inches

(millimeters)

60”Models A B C D E F

One Sided Framing 75-1/2

(1918) 19-1/2

(496) 54-3/4

(1391) 16

(407) 12

(305) 96

(2439)

See Thru Framing 75-1/2

(1918) 18-1/2

(469) 54-3/4

(1391) 16

(407) 12

(305) 96

(2439)

• SEETHRUKT-LIN60 (Required for See-Thru Installation)

• Two Jack Studs Located on the Front for One Sided Application

• Two Jack Studs Located Back and Front for See-Thru Application.

F. Minimum height from appliance base to ceiling

Astria.us.com900909-00_B 15

PRE-INSTALLATION Continued

Note: Remove Fireboard Nailing Flange and ﬁreboard nailing ﬂange

top spacers for recessed installation (Figure 6).

Secure

Nailing

ﬂanges to

Jack Stud

Secure

Fireboard Nailing

Flange(Front and

Inside Framing

Figure 5 - Framing Flush wall with Heatﬂo

Fireplace Framing Recessed Wall Pocket & HeatFlo Kit (For TV

Installation)

Fireplace Framing Flush Wall & HeatFlo Kit (For TV Installation)

For one sided regular application, ﬁnish installing rear panel by

securing with ten (10) self tapping screws included with the ﬁreplace

(Figure 7).

Table 5 - Framing Dimensions with Heatﬂo Installation - Inches

(millimeters)

60” Models A B C D E F *G H J

One Sided Framing 75-1/2

(1918) 19-1/2

(496) 54-3/4

(1391) 16

(407) 12

(305) 96

(2439) 6

(153) 64-1/4

(1632) 7-1/2

(191)

See Thru Framing 75-1/2

(1918) 18-1/2

(469) 54-3/4

(1391) 16

(407) 12

(305) 96

(2439) 6

(153) 64-1/4

(1632) 7-1/2

(191)

• HTFLO-LIN60 (Required for TV Installation)

• SEETHRUKT-LIN60 (Required for See-Thru Installation)

• Two Jack Studs Located on the Front for One Sided Application

• Two Jack Studs Located Back and Front for See-Thru Application.

F. Minimum height from appliance base to ceiling

*G. Minimum Distance from Heat Register Vent Opening to Ceiling

Remove Fireboard Nailing

Flange Top Spacers for

Recessed Installation

Figure 6 - Removing Fireboard Nailing Flanges and Fireboard Nailing

Flange Top Spacers for Recessed Wall Pocket Installation

Figure 7 - Finishing Installation of Rear Panel

Fireboard

Nailing Flange

Fireplace

Top

Spacer

Astria.us.com 900909-00_B16

PRE-INSTALLATION Continued

Table 7 - Fireplace Framing Speciﬁcations—Corner Installation

with Horizontal termination

Model A B C D E F

60” 73-3/8”

(1864

mm)

113-1/4”

(2877

mm)

80”

(2032

mm)

56-5/8”

(1439

mm)

33-1/2”

(851

mm)

1”

(26 mm)

7 (178)

NOTE: Back wall of chase/enclosure (including ﬁnishing materials) shown.

Table 6 - Fireplace Framing Dimensions for Recessed Wall Pocket TV Installation One Sided & See-Thru Application - Inches

(millimeters

60” Models A B C D E F *G H J K L

One Sided Framing 75-1/2

(1918) 19-1/2

(496) 44-3/4

(1137) 16

(407) 12

(305) 96

(2439) 6

(153) 64-1/4

(1632) 7-1/2

(191) 36-1/2

(928) 3-1/2 (89)

See Thru Framing 75-1/2

(1918) 18-1/2

(470) 44-3/4

(1137) 16

(407) 12

(305) 96

(2439) 6

(153) 64-1/4

(1632) 7-1/2

(191) 36-1/2

(928) 3-1/2 (89)

• HTFLO-LIN60 (Required for TV Installation)

• SEETHRUKT-LIN60 (Required for See-Thru Installation)

• Two Jack Studs Located on the Front for One Sided Application

• Two Jack Studs Located Back and Front for See-Thru Application.

F. Minimum height from appliance base to ceiling

*G. Minimum Distance from Heat Register Vent Opening to Ceiling

Secure

Nailing

ﬂanges to

Jack Stud

Fireplace

Top

Spacers

Astria.us.com900909-00_B 17

PRE-INSTALLATION Continued

Table 8 - Fireplace Dimensions

Models A B C D E F G H J K L M N

60” Models 36-5/8

(931) 14

(356) 8-5/8

(219) 9-3/8

(239) 20-7/8

(531) 9-3/4

(248) 61-1/4

(1556) 73-1/4

(1861) 78-1/4

(1988) 34-3/8

(874) 37-3/4

(959) 44-5/8

(1134) 54-5/8

(1388)

Models P Q R S T U V W

60” Models 3-1/2

(89) 43-1/2

(1105) 3/4

(19) 18-1/2

(470) 19-1/4

(489) 5/8

(16) 57-1/8

(1451) 15-1/2

(394)

BBBB CC

TOP VIEW

FRONT VIEW RIGHT SIDE VIEW

Requires Metal-Fab Sure-Seal

5” (127) I.D. 8” (203) O.D.

Direct-Vent Pipe

Gas Line

Connection

Electrical Connection is

Located on the Left Side.

Both, Gas Line Connection and

Electrical Connection May Be

Interchangeable.

Astria.us.com 900909-00_B18

TERMINATION LOCATION AND CLEARANCES

Table 9 - Horizontal vent termination clearances for buildings with combustible and noncombustible exteriors

Fixed

Closed Openable Fixed

Closed

TERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

Openable

See Table 13

Inside Corner

Outside Corner Recessed Location

Balcony with No Side

Wall

Balcony with Perpendicular Side Wall

NPO

U.S. Installation ** Canadian Installation *

AClearance above grade, veranda, porch, desk, or balcony 12” (300 mm) ** 12” (300 mm) *

BClearance to window or door that may be opened 6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

9” (230 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW), and < 50,000 Btu/h (15

kW),

12” (300 mm)

for ﬁreplaces > 50,000 Btu/h (15 kW) **

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

12” (300 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW)

CClearance to permanently closed window 9” (229 mm)

recommended to prevent window condensation 12” (305 mm)

recommended to prevent window

condensation

DVertical clearance to ventilated sofﬁt located above the

termination within a horizontal distance of 18” (458 mm) 18” (458 mm) 18” (458 mm)

EClearance to unventilated sofﬁt 12” (305 mm)

30” (760 mm) to vinyl sofﬁt 12” (305 mm)

30” (760 mm) to vinyl sofﬁt

FClearance to outside corner 5” (127 mm)

minimum 5” (127 mm)

minimum

GClearance to inside corner 2” (51 mm) minimum 2” (51 mm) minimum

HClearance to each inside of center line extended above

meter / regulator assembly 36” (910 mm)

within a height of 15 ft above the meter / regulator assembly ** 36” (910 mm)

within a height of 15 ft above the meter /

regulator assembly *

IClearance to service regulator vent outlet 36” (910 mm)** 36” (910 mm)*

JClearance to nonmechanical air supply inlet to building or

the combustion air inlet to any other ﬁreplace 6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

9” (230 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW) and < 50,000 Btu/h (15 kW),

12” (300 mm)

for ﬁreplaces > 50,000 Btu/h (15 kW)**

6” (150 mm)

for ﬁreplaces < 10,000 Btu/h (3 kW),

12” (300 mm)

for ﬁreplaces > 10,000 Btu/h (3 kW)

KClearance to a mechanical air supply inlet 36” (910 mm) above if within 10 ft (3 m) horizontally ** 72” (1830 mm) *

LClearance above paved sidewalk or paved driveway located

on public property 84” (2130 mm) ‡ 84” (2130 mm) ‡

MClearance under veranda, porch, deck or balcony 12” (300 mm) *‡ 12” (300 mm) *‡

NDepth of alcove (maximum) 72” (1830 mm) ** 72” (1830 mm) *

OClearance to termination (alcove) 6” (15.2 mm) ** 6” (15.2 mm)*

PWidth of alcove (minimum) 36” (910 mm) ** 36” (910 mm) *

QClearance to combustible above (alcove) 18” (457 mm) ** 18” (457 mm) *

‡

*‡

In accordance with the current CAN/CGA-B149.1 National Gas And Propane Installation Code

In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

Only permitted if veranda, porch, deck, or balcony is fully-open on a minimum two sides beneath the ﬂoor

Astria.us.com900909-00_B 19

VENTING INSTALLATION

These ﬁreplaces are tested and approved for use with Metal-Fab

Sure-Seal Direct Vent Pipe components and terminations.

The venting system must terminate on the outside of the structure

and can not be attached to a chimney or ﬂue system serving a sepa-

rate solid fuel or gas burning appliance. A direct vent appliance must

have its own venting system. DO NOT common vent this appliance.

These models are approved to be vented either horizontally through

an outside wall or vertically through a roof or chase enclosure using

the following guidelines:

• When venting system terminates horizontally on an outside wall,

you may install a standoff if the termination cap is to be installed

directly on a combustible ﬁnish such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may cause excessive tem-

peratures which could cause a ﬁre.

• Vent pipe air space clearances to combustibles are 1" on all sides

except on the horizontal sections, which requires 3" clearance

from the top of the pipe. Where the termination cap penetrates a

combustible wall, 1" air space clearance is required.

• Have ﬁreplace and selected vent components on hand to help

determine the exact measurements when elbowing or offsetting.

Always use wall ﬁrestops when penetrating walls and ﬁrestops

when penetrating ceilings or attic spaces.

INSTALLATION PRECAUTIONS

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or when on roof tops

• Be aware of electrical wiring locations in walls and ceilings

WARNING

Read all instructions completely and thoroughly

before attempting installation. Failure to do so

could result in serious injury, property damage or

loss of life.

WARNING

This gas ﬁreplace and vent assembly must be vented

directly to the outside. The venting system must

NEVER be attached to a chimney serving a separate

solid fuel burning appliance. Each direct vent gas

appliance must use a separate vent system. Do not

use common vent systems.

NOTICE

Read these instructions completely before

attempting installation.

NOTICE

Failure to follow these instructions will void the

warranty

NOTICE

Do not seal termination cap to vent pipe. Cap must

be removable for vent inspection and maintenance.

The following actions will void the warranty on your venting

system:

• Installation of any damaged venting component

• Unauthorized modiﬁcation of the venting system (Do not cut or alter

vent components)

• Installation of any component part not manufactured or approved

by INNOVATIVE HEARTH PRODUCTS

• Installation other than as instructed by these instructions

VENT INSTALLATION PLANNING

There are two basic types of direct vent installation:

• Horizontal Termination

• Vertical Termination

Horizontal Termination Installation

IMPORTANT: Horizontal square terminations require only inner por-

tion of wall ﬁrestop. Horizontal installations using round termination

require exterior portion of wall ﬁrestop.

1. Set ﬁreplace in its desired location and determine the route your

horizontal venting will take. Do not secure ﬁreplace until all vent-

ing has been installed. Some installations require sliding ﬁreplace

in and out of position to make ﬁnal venting connections. Figures

11 and 12 on page 21 show different conﬁgurations for venting

with horizontal termination that will help you decide which ap-

plication best suits your installation. Check to see if wall studs

or roof rafters are in the path of your desired venting route. If

they are, you may want to adjust location of ﬁreplace.

2. Direct vent pipe sections and components are designed with

special twist-lock connections.

Twist-Lock Procedure: Female ends of pipes have locking lugs

(indentations). These lugs will slide straight into matching slots

on male ends of adjacent pipes. Push pipe sections together and

twist one section clockwise approximately one-quarter turn until

sections are fully locked (see Figure 8, page 20).

Note: Horizontal runs of vent must be supported every three feet.

Use wall straps for this purpose.

3. Assemble desired combination of pipe and elbows to ﬁreplace ﬂue

collar. If there are long portions of venting run, pre-assembled

pipe sections may be installed as subassemblies for convenience.

WARNING

Vent pipe air space clearances to combustibles are

1" on all sides except on the horizontal sections,

which require 3" clearances from the top of the pipe.

Where the termination cap penetrates a combustible

wall, 1" air space clearance is required.

Astria.us.com 900909-00_B20

(Framing

Detail)

11"

11" Inside Framing

11"

Vent Opening

Combustible Wall

Vent Opening

Noncombustible Wall

4. Carefully determine location where vent pipe assembly will pen-

etrate outside wall. Center of hole should line up with center line

of horizontal vent pipe. Mark wall for an 11" x 11" square hole. Cut

and frame square hole in exterior wall where vent will be termi-

nated. If wall being penetrated is constructed of noncombustible

material, such as masonry block or concrete, a 8 1/2" hole with

zero clearance is acceptable (see Figure 9).

Figure 8 - Vent Pipe Connections

Female Locking

Lugs

Male

Slots

Figure 9 - Vent Opening Requirements

VENTING INSTALLATION Continued

Figure 10 - Installing Horizontal Vent Cap

(Noncombustible Exterior)

Wood

Screw

Vent Cap

Apply Mastic

to All Four

Sides

5. Noncombustible Exterior Wall: Position horizontal vent cap in

center of the 8 1/2" round hole and attach to exterior wall with

four wood screws provided. Before attaching vent cap to exterior

wall, run a bead of non-hardening mastic (pliable sealant) around

outside edges to make a seal between it and outside wall.

Note: Four wood screws provided should be replaced with ap-

propriate fasteners for stucco, brick, concrete or other types of

sidings (see Figure 10).

Combustible Exterior Wall: For vinyl siding, stucco or wood

exteriors, a siding standoff may be installed between vent cap

and exterior wall. Siding standoff prevents excessive heat from

damaging siding materials. Siding material must be cut to accom-

modate standoff. Bolt vent cap to standoff. Apply non-hardening

mastic around outside edge of standoff. Position standoff/cap

assembly in the center of 11" square hole and attach to exterior

wall with provided wood screws (see Figure 11, page 21). Siding

standoff must sit ﬂush against exterior fascia material.

6. Connecting Vent Cap with Horizontal Vent Pipe: Slide wall

ﬁrestop over vent pipe before connecting horizontal run to vent

cap (see Figure 12, page 21).

Carefully move ﬁreplace, with vent assembly attached, toward

wall and insert vent pipe into horizontal termination. Pipe overlap

should be a minimum of 1 1/4" (see Figure 13, page 21).

Slide wall ﬁrestop against interior wall surface and attach with

screws provided. See Figure 13, page 21 for horizontal termina-

tion details.

Place ﬁreplace into position and shim with noncombustible ma-

terial if needed. Nail or screw side ﬂanges to framing to secure

unit in place. IMPORTANT: Make sure ﬁreplace is level before

securing. If ﬁreplace is not level it will not work properly.

WARNING

Do not recess vent termination into any wall. This

will cause a ﬁre hazard.

Center

of Hole

La page charge ...

Astria Fireplaces Allume ST Mode d'emploi

Marque: Astria Fireplaces

Modèle: Allume ST

Catégorie: Poêles

Taper: Mode d'emploi

Ce manuel convient également à

Allume

Télécharger le PDF

rapport

dans d''autres langues

English: Astria Fireplaces Allume ST Operating instructions

Astria Fireplaces Allume ST Mode d'emploi

Ce manuel convient également à

Astria Fireplaces Allume ST Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents