Sony CDX-L600X Manuel utilisateur

Marque: Sony

Modèle: CDX-L600X

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Operating Instructions

Mode d’emploi

CDX-L600X

3-237-612-11 (1)

FM/AM

Compact Disc

Player

For installation and connections, see the supplied installation/connections

manual.

En ce qui concerne l’installation et les connexions, consulter le manuel

d’installation/raccordement fourni.

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record these numbers in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this

product.

Model No. CDX-L600X Serial No.

Welcome !

Thank you for purchasing this Sony Compact

Disc Player. You can enjoy its various features

even more with:

•CD TEXT information (displayed when a CD

TEXT disc* is played).

•Supplied controller accessories

Card remote commander RM-X114

•Optional controller accessories

Rotary commander RM-X4S

* A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name,

and track names. This information is recorded on

the disc.

Warning

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instructions,

may cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the user

is encouraged to try to correct the interference

by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the

equipment and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/

TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

CAUTION

The use of optical instruments with this

product will increase eye hazard.

Table of Contents

Location of controls .................................................. 4

Precautions ................................................................ 6

Notes on discs ........................................................... 6

Getting Started

Resetting the unit ................................................. 7

Detaching the front panel ................................... 8

Setting the clock ................................................... 9

CD Player

Playing a disc ........................................................ 9

Display items ...................................................... 10

Playing tracks repeatedly

— Repeat Play ............................................... 10

Playing tracks in random order

— Shuffle Play ............................................... 10

Radio

Storing stations automatically

— Best Tuning Memory (BTM) ................... 11

Receiving the stored stations ............................ 11

Storing only the desired stations ..................... 12

Storing station names

— Station Memo ........................................... 12

Locating a station by name

— List-up ....................................................... 13

Other Functions

Using the rotary commander ........................... 14

Adjusting the sound characteristics ................ 15

Quickly attenuating the sound ........................ 15

Changing the sound and display settings

— Menu .......................................................... 16

Selecting the sound position

— “My Best sound Position (MBP)” .......... 17

Setting the equalizer .......................................... 17

Additional Information

Maintenance........................................................ 18

Removing the unit ............................................. 19

Specifications ...................................................... 20

Troubleshooting.................................................. 21

Error displays/Messages .................................. 22

Location of controls

MBP (My Best sound Position) button

2 Z (eject) button (located on the front side

of the unit, behind the front panel) 9

3 MENU button 9, 11, 12, 13, 16, 18

4 Volume control dial

5 LIST button 13

6 Receptor for the card remote

commander

7 Display window

8 OPEN button 8, 9

9 EQ7 button 17

0 RESET button (located on the front side of

the unit, behind the front panel) 7

qa OFF (Stop/Power off) button* 8, 9

qs SOUND button 15, 17

qd SOURCE (Power on/Radio/CD) button

8, 9, 11, 12, 17

CDX-L600X

Refer to the pages listed for details.

: During Playback : During radio reception : During menu mode

qf ENTER button

9, 11, 12, 13, 16, 18

qg MODE button 11, 12

qh DSPL (display mode change) button

10, 13

qj Number buttons

(1) REP 10

(2) SHUF 10

11, 12

* Warning when installing in a car

without an ACC (accessory) position

on the ignition key switch

Be sure to press (OFF) on the unit for 2

seconds to turn off the clock display after

turning off the engine.

Otherwise, the clock display does not turn

off and this causes battery drain.

RADIO

CD RADIO

RADIO

(SEEK)

(–): to select

leftwards/

Card remote commander

RM-X114

The corresponding buttons of the card

remote commander control the same

functions as those on this unit.

1 DSPL button

2 MENU button

3 SOURCE button

4 SEEK (</,) buttons

5 SOUND button

6 OFF button

7 VOL (+/–) buttons

8 MODE button

9 LIST button

0 PRESET (M/m) buttons

qa ENTER button

qs ATT button

Note

If the unit is turned off by pressing (OFF) for 2

seconds, it cannot be operated with the card

remote commander unless (SOURCE) on the unit is

pressed, or a disc is inserted to activate the unit

first.

Tip

Refer to “Replacing the lithium battery” for details

on how to replace the batteries (page 19).

(SEEK)

(+):to select

rightwards

(PRESET)

(+): to select upwards

(PRESET)

(–): to select downwards

qk PRESET buttons (+/–)

11, 13

9, 11, 12, 13, 16, 18

ql SEEK buttons (–/+) 15

11, 12

9, 12, 16, 18

RADIO

DISC

–

ATTOFF

DSPL MODE

SOURCE

DISC

VOL

–

PRESET

SEEK

–

PRESET –

ENTER

LIST

In menu mode, the currently selectable

button (s) of these four are indicated with a

“M” in the display.

Precautions

•If your car was parked in direct sunlight,

allow the unit to cool off before operating it.

•Power antennas will extend automatically

while the unit is operating.

If you have any questions or problems

concerning your unit that are not covered in

this manual, please consult your nearest Sony

dealer.

Moisture condensation

On a rainy day or in a very damp area,

moisture condensation may occur inside the

lenses and display of the unit. Should this

occur, the unit will not operate properly. In

such a case, remove the disc and wait for about

an hour until the moisture has evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft

drinks onto the unit or discs.

Notes on discs

•To keep the disc clean, do not touch the

surface. Handle the disc by its edge.

•Keep your discs in their cases or disc

magazines when not in use. Do not subject

the discs to heat/high temperature. Avoid

leaving them in parked cars or on

dashboards/rear trays.

•Do not attach labels, or use discs with sticky

ink/residue. Such discs may stop spinning

when used, causing a malfunction, or may

ruin the disc.

•Discs with special shapes (heart-shaped

discs, octagonal discs, etc.) cannot be played

on this unit. Attempting to do so may

damage the unit. Do not use such discs.

• You cannot play 8 cm (3 in.) CDs.

•Before playing, clean the discs with a

commercially available cleaning cloth. Wipe

each disc from the center out. Do not use

solvents such as benzine, thinner,

commercially available cleaners, or antistatic

spray intended for analog discs.

Getting Started

Resetting the unit

Before operating the unit for the first time or

after replacing the car battery, you must reset

the unit.

Remove the front panel and press the RESET

button with a pointed object, such as a ball-

point pen.

Note

Pressing the RESET button will erase the clock

setting and some stored contents.

RESET button

Notes on CD-R/CD-RW discs

•You can play CD-Rs (recordable CDs)/CD-

RWs (rewritable CDs) designed for audio use

on this unit.

Look for these marks to distinguish CD-Rs/

CD-RWs for audio use.

These marks denote that a disc is not for

audio use.

•Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the

condition of the disc) may not play on this

unit.

•You cannot play a CD-R/CD-RW that is not

finalized*.

* A process necessary for a recorded CD-R/CD-RW

disc to be played on the audio CD player.

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

Caution alarm

If you turn the ignition switch to the OFF

position without removing the front panel, the

caution alarm will beep for a few seconds.

If you connect an optional amplifier and do not

use the built-in amplifier, the beep sound will

be deactivated.

1 Press (OFF)*.

CD playback or radio reception stops (the

key illumination and display remain on).

* If your car has no ACC position on the

ignition switch, be sure to turn the unit off by

pressing (OFF) for 2 seconds to avoid car

battery drain.

2 Press (OPEN), then slide the front panel

to the right, and gently pull out the left

end of the front panel.

Notes

• If you detach the panel while the unit is still

turned on, the power will turn off automatically

to prevent the speakers from being damaged.

• Do not drop or put excessive pressure on the

front panel and its display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in

parked cars or on dashboards/rear trays.

Tip

When carrying the front panel with you, use the

supplied front panel case.

Attaching the front panel

Place hole A of the front panel onto the

spindle B on the unit, then lightly push the

left side in.

Press (SOURCE) (or insert a CD) to operate the

unit.

Note

Do not put anything on the inner surface of the

front panel.

Setting the clock

The clock uses a 12-hour digital indication.

Example: To set the clock to 10:08

1 Press (MENU), then press either side of

(PRESET) repeatedly until “CLOCK”

appears.

1 Press (ENTER).

The hour indication flashes.

2 Press either side of (PRESET) to set

the hour.

3 Press the (+) side of (SEEK).

The minute indication flashes.

4 Press either side of (PRESET) to set

the minute.

2 Press (ENTER).

The clock starts. After the clock setting is

completed, the display returns to normal

play mode.

Tip

When D.INFO mode is set to ON, the time is always

displayed (page 16).

CD Player

Playing a disc

1 Press (OPEN) and insert the disc

(labeled side up).

2 Close the front panel.

Playback starts automatically.

If a disc is already inserted, press (SOURCE)

repeatedly until “CD” appears to start

playback.

To Press

Stop playback (OFF)

Eject the disc (OPEN) then Z

Skip tracks (SEEK) (./>)

– Automatic [once for each track]

Music Sensor

Fast-forward/ (SEEK) (m/M)

reverse [hold to desired point]

– Manual Search

Note

When the last track on the disc is over, playback

restarts from the first track of the disc.

Display items

When the disc/track changes, any prerecorded

title of the new disc/track is automatically

displayed (if the Auto Scroll function is set to

“ON,” names exceeding 8 characters will be

scrolled (page 16)).

Displayable items

• Music source

• Clock

• Function

Displayable items

• Disc name*

/artist name*

• Track title*

• Elapsed playing time

To Press

Switch display (DSPL)

item

“NO NAME” indicates there is no prerecorded

name to display.

Only for CD TEXT discs with the artist name.

Notes

• Some characters cannot be displayed.

• For some CD TEXT discs with very many

characters, information may not scroll.

• This unit cannot display the artist name for each

track of a CD TEXT disc.

Playing tracks repeatedly

— Repeat Play

The current track will repeat itself when it

reaches the end.

During playback, press (1) (REP)

repeatedly until “REP-1” appears in the

display.

Repeat Play starts.

To return to normal play mode, select

“REP-OFF.”

Playing tracks in random

order — Shuffle Play

You can select to play the tracks on the current

disc in random order.

During playback, press (2) (SHUF)

repeatedly until “SHUF-1” appears in the

display.

Shuffle Play starts.

To return to normal play mode, select

“SHUF-OFF.”

Radio

The unit can store up to 6 stations per band

(FM1, FM2, FM3, AM1, and AM2).

Caution

When tuning in stations while driving, use

Best Tuning Memory to prevent accidents.

Storing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals within the selected band, and stores

them in the order of their frequency.

1 Press (SOURCE) repeatedly to select the

radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (MENU), then press either side of

(PRESET) repeatedly until “BTM”

appears.

4 Press (ENTER).

A beep sounds when the setting is stored.

Notes

• If only a few stations can be received due to

weak signals, some number buttons will retain

their former settings.

• When a number is indicated in the display, the

unit starts storing stations from the one currently

displayed.

Receiving the stored

stations

1 Press (SOURCE) repeatedly to select the

radio.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6)) on

which the desired station is stored.

Tip

Press either side of (PRESET) to receive the

stations in the order they are stored in the memory

(Preset Search function).

If preset tuning does not work

Press either side of (SEEK) to search for

the station (automatic tuning).

Scanning stops when the unit receives a

station. Repeat until the desired station is

received.

Tips

• If automatic tuning stops too frequently, turn on

the Local Seek to limit seek to stations with

stronger signals (see “Changing the sound and

display settings,” page 16).

• If you know the frequency of the station you

want to listen to, press and hold either side of

(SEEK) to locate the approximate frequency,

then press (SEEK) repeatedly to fine adjust to

the desired frequency (manual tuning).

If FM stereo reception is poor

Select monaural reception mode.

(see “Changing the sound and display

settings,” page 16).

The sound improves, but becomes

monaural (“ST” disappears).

Note

If interference occurs, this unit will automatically

narrow the reception frequency to eliminate noise

(IF AUTO function). In such cases, some FM stereo

broadcasts may become monaural while in the

stereo reception mode.

Tip

To always hear FM stereo broadcasts in stereo, you

can change the IF AUTO setting and widen the

frequency signal reception (see “Changing the

sound and display settings,” page 16). Note that

some interference may occur in this setting.

Storing only the desired

stations

You can manually preset the desired stations

on any chosen number button.

1 Press (SOURCE) repeatedly to select the

radio.

2 Press (MODE) repeatedly to select the

band.

3 Press either side of (SEEK) to tune in the

station that you want to store.

4 Press the desired number button ((1) to

(6)) for 2 seconds until “MEM” appears.

The number button indication appears in

the display.

Note

If you try to store another station on the same

number button, the previously stored station will

be erased.

Storing station names

— Station Memo

You can assign a name to each radio station

and store it in memory. The name of the

station currently tuned in appears in the

display. You can assign a name using up to 8

characters for a station.

Storing the station names

1 Tune in a station whose name you want

to store.

2 Press (MENU), then press either side of

(PRESET) repeatedly until “NAMEEDIT”

appears.

3 Press (ENTER).

4 Enter the characters.

1 Press the (+)*

side of (PRESET)

repeatedly to select the desired

character.

A t B t C … t 0 t 1 t 2 …

t + t – t

… t _*

t A

For reverse order, press the (–) side of

(PRESET).

(blank space)

2 Press the (+) side of (SEEK) after

locating the desired character.

If you press the (–) side of (SEEK), you

can move back to the left.

3 Repeat steps 1 and 2 to enter the

entire name.

5 Press (ENTER).

Tips

• Simply overwrite or enter “_” to correct or erase

a name.

• There is another way to start storing station

names: Press (LIST) for 2 seconds instead of

performing steps 2 and 3. You can also complete

the operation by pressing (LIST) for 2 seconds

instead of step 5.

Displaying the station name

Switch the display item to frequency or station

name*.

To Press

Switch display (DSPL) during radio

item reception

* If the station name is not stored, “NO NAME”

appears in the display for one second.

Erasing the station name

1 During radio reception, press (MENU),

then press either side of (PRESET)

repeatedly until “NAME DEL” appears.

2 Press (ENTER).

3 Press either side of (PRESET) repeatedly

to select the station whose name you

want to erase.

4 Press (ENTER) for 2 seconds.

The name is erased.

Repeat steps 3 to 4 if you want to erase

other names.

5 Press (MENU) twice.

The unit returns to normal radio reception

mode.

Note

If you have already erased all of the station names,

“NO DATA” appears in step 4.

Locating a station by

name — List-up

1 During radio reception, press (LIST).

The name assigned to the station currently

tuned appears in the display.

2 Press either side of (PRESET) repeatedly

until you find the desired station.

If no name is assigned to the selected

station, the frequency appears in the

display.

3 Press (ENTER) to tune in the desired

station.

By rotating the control

Rotate and release to:

– Skip tracks.

– Tune in stations automatically.

Rotate, hold, and release to:

– Fast-forward/reverse a track.

– find a station manually.

By pushing in and rotating the

control

Push in and rotate the control to:

– Receive preset stations.

Rotate the VOL control

to adjust the volume.

Other Functions

You can also control the unit with a rotary

commander (optional).

Using the rotary

commander

First, attach the appropriate label depending

on how you want to mount the rotary

commander.

The rotary commander works by pressing

buttons and/or rotating controls.

SOUND

DSPL

MODE

SOUND

DSPL

ODE

By pressing buttons

OFF

Press To

(SOURCE) Change source (radio/CD)

(MODE) Change radio band

(ATT) Attenuate sound

(OFF)* Stop playback or radio

reception

(SOUND) Adjust the sound menu

(DSPL) Change the display item

* If your car has no ACC (accessory) position on the

ignition key switch, be sure to press (OFF) for 2

seconds to turn off the clock indication after

turning off the ignition.

(OFF)

(MODE)

(ATT)

(DSPL)

(SOURCE)

(SOUND)

SEEK/AMS

control

PRESET

control

Changing the operative direction

The operative direction of controls is factory-

set as shown below.

If you need to mount the rotary commander on

the right hand side of the steering column, you

can reverse the operative direction.

Press (SOUND) for 2 seconds while

pushing the VOL control.

To increase

To decrease

Adjusting the sound

characteristics

You can adjust the bass, treble, balance, and

fader.

The bass and treble levels can be stored

independently for each source.

1 Select the item you want to adjust by

pressing (SOUND) repeatedly.

Each time you press (SOUND), the item

changes as follows:

BAS (bass) t TRE (treble) t

BAL (left-right) t FAD (front-rear)

2 Adjust the selected item by pressing

either side of (SEEK).

When adjusting with the rotary

commander, press (SOUND) and rotate the

VOL control.

Note

Adjust within 3 seconds after selecting the item.

Quickly attenuating the

sound

(With the rotary commander or the card

remote commander)

Press (ATT) on the rotary commander or

card remote commander.

After “ATT-ON” momentarily appears, the

“ATT” appears in the display.

To restore the previous volume level, press

(ATT) again.

Changing the sound and

display settings — Menu

The following items can be set:

SET (Set Up)

•CLOCK (page 9)

•BEEP — to turn the beeps on or off.

•RM (Rotary Commander) — to change the

operative direction of the controls of the

rotary commander.

— Select “NORM” to use the rotary

commander as the factory-set position.

— Select “REV” when you mount the rotary

commander on the right side of the

steering column.

DSPL (Display)

•D.INFO (Dual Information) — to display the

clock and the play mode at the same time

(ON).

•M.DSPL (Motion Display) — to select the

Motion Display mode from “1,” “2,” and

“OFF.”

— Select “1” to show decoration lines in the

display and activate Demo display.

— Select “2” to show decoration lines in the

display and deactivate Demo display.

— Select “OFF” to deactivate the Motion

Display.

•A.SCRL (Auto Scroll)

— Select “ON” to scroll all automatically

displayed names exceeding 8 characters.

— When Auto scroll is set to off and the

disc/track name is changed, the disc/

track name does not scroll.

SND (Sound)

•LOUD (Loudness) — to enjoy bass and treble

even at low volumes. The bass and treble will

be reinforced.

P/M (Play Mode)

•LOCAL-ON/OFF (Local seek mode)

(page 11)

— Select “ON” to only tune into stations

with stronger signals.

•MONO-ON/OFF (Monaural mode) (page 11)

— Select “ON” to hear FM stereo broadcast

in monaural. Select “OFF” to return to

normal mode.

•IF AUTO/WIDE (page 11)

1 Press (MENU).

To set A.SCRL, press (MENU) during CD

Playback.

2 Press either side of (PRESET) repeatedly

until the desired item appears.

3 Press the (+) side of (SEEK) to select the

desired setting (Example: ON or OFF).

4 Press (ENTER).

After the mode setting is completed, the

display returns to normal play mode.

Note

The displayed item will differ depending on the

source.

Tip

You can easily switch among categories (“SET,”

“DSPL,” “SND,” “P/M,” and “EDIT”) by pressing

either side of (PRESET) for 2 seconds.

Selecting the sound

position

— “My Best sound Position (MBP)”

When you drive without passengers, you can

enjoy the most comfortable sound

environment with “My Best sound Position.”

“My Best sound Position” has two presets,

which adjust the sound level of balance and

fader. You can select one very easily with the

MBP button.

Press (MBP) repeatedly for the desired

listening position.

The mode of “My Best sound Position” is

shown in the display in order of the table.

After one second, the display goes back to

the normal playback mode.

If you want to adjust the sound level of

balance and fader more precisely, you can

do it using the (SOUND) button. (See

“Adjusting the sound characteristics” on

page 15.)

Notes

• When the BAL (balance) or FAD (fader) in

“Adjusting the sound characteristics” (page 15) is

adjusted, the MBP setting returns to OFF.

• When MBP is set to OFF, the BAL and FAD setting

is activated.

Display

window

MBP-A

MBP-B

MBP-OFF

Right

– 4dB

Left

– 4dB

Front

Rear

– 4dB

Balance Level Fader Level

Setting the equalizer

You can select an equalizer curve for seven

music types (VOCAL, CLUB, JAZZ, NEW

AGE, ROCK, CUSTOM, and XPLOD).

You can store and adjust the equalizer settings

for frequency and level.

Selecting the equalizer curve

1 Press (SOURCE) to select a source (radio

or CD).

2 Press (EQ7) repeatedly until the desired

equalizer curve appears.

Each time you press (EQ7), the item

changes.

To cancel the equalizing effect, select

“OFF.”

After 3 seconds, the display returns to the

normal playback mode.

continue to next page t

Adjusting the equalizer curve

1 Press (MENU).

2 Press either side of (PRESET) repeatedly

until “EQ7 TUNE” appears, then press

(ENTER).

3 Press either side of (SEEK) to select the

desired equalizer curve, then press

(ENTER).

Each time you press (SEEK), the item

changes.

4 Select the desired frequency and level.

1 Press either side of (SEEK) to select

the desired frequency.

Each time you press (SEEK), the

frequency changes.

62 Hz y 157 Hz y 396 Hz

y 1.0 kHz y 2.5 kHz y 6.3 kHz

y 16.0 kHz

2 Press either side of (PRESET) to

adjust the desired volume level.

The volume level is adjustable by 1 dB

steps from –10 dB to +10 dB.

To restore the factory-set equalizer

curve, press (ENTER) for two seconds.

5 Press (MENU) twice.

When the effect setting is complete, the

normal playback mode appears.

Additional

Information

Maintenance

Fuse replacement

When replacing the fuse, be sure to use one

matching the amperage rating stated on the

original fuse. If the fuse blows, check the

power connection and replace the fuse. If the

fuse blows again after replacement, there may

be an internal malfunction. In such a case,

consult your nearest Sony dealer.

Warning

Never use a fuse with an amperage rating

exceeding the one supplied with the unit as

this could damage the unit.

Cleaning the connectors

The unit may not function properly if the

connectors between the unit and the front

panel are not clean. In order to prevent this,

detach the front panel (page 8) and clean the

connectors with a cotton swab dipped in

alcohol. Do not apply too much force.

Otherwise, the connectors may be damaged.

Main unit

Back of the front panel

Fuse (10 A)

Removing the unit

1 Remove the front cover

1 Detach the front panel (page 8).

2 Press the clip inside the front cover

with a thin screwdriver.

3 Repeat step 2 for the other side.

2 Remove the unit

1 Use a thin screwdriver to push in the

clip on the left side of the unit, then

pull out the left side of the unit until

the catch clears the mounting.

2 Repeat step 1 for the right side.

3 Slide the unit out of its mounting.

Notes

• For safety, turn off the ignition before cleaning

the connectors, and remove the key from the

ignition switch.

• Never touch the connectors directly with your

fingers or with any metal device.

Replacing the lithium battery

Under normal conditions, batteries will last

approximately 1 year. (The service life may be

shorter, depending on the conditions of use.)

When the battery becomes weak, the range of

the card remote commander becomes shorter.

Replace the battery with a new CR2025 lithium

battery.

+ side up

Notes on lithium battery

•Keep the lithium battery out of the reach of

children. Should the battery be swallowed,

immediately consult a doctor.

•Wipe the battery with a dry cloth to assure a

good contact.

•Be sure to observe the correct polarity when

installing the battery.

•Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of

in fire.

4 mm

(

/16 in.)

Specifications

CD player section

Signal-to-noise ratio 90 dB

Frequency response 10 – 20,000 Hz

Wow and flutter Below measurable limit

Laser Diode Properties

Material GaAlAs

Wavelength 780 nm

Emission Duration Continuous

Laser output power Less than 44.6 µW*

* This output is the value measured at a distance

of 200 mm from the objective lens surface on the

Optical Pick-up Block.

Tuner section

Tuning range 87.5 – 107.9 MHz

Antenna terminal External antenna connector

Intermediate frequency 10.7 MHz/450 kHz

Usable sensitivity 8 dBf

Selectivity 75 dB at 400 kHz

Signal-to-noise ratio 66 dB (stereo),

72 dB (mono)

Harmonic distortion at 1 kHz

0.6 % (stereo),

0.3 % (mono)

Separation 35 dB at 1 kHz

Frequency response 30 – 15,000 Hz

Tuning range 530 – 1,710 kHz

Antenna terminal External antenna connector

Intermediate frequency 10.7 MHz/450 kHz

Sensitivity 30 µV

Power amplifier section

Outputs Speaker outputs

(sure seal connectors)

Speaker impedance 4 – 8 ohms

Maximum power output 52 W × 4 (at 4 ohms)

General

Outputs Audio outputs

Power antenna relay

control lead

Power amplifier control

lead

Input Telephone ATT control

lead

Tone controls Bass ±10 dB at 62 Hz

Treble ±10 dB at 16 kHz

Loudness +8 dB at 100 Hz

+2 dB at 10 kHz

Power requirements 12 V DC car battery

(negative ground)

Dimensions Approx. 178 × 50 × 176 mm

/8 × 2 × 7 in.)

(w/h/d)

Mounting dimensions Approx. 182 × 53 × 161 mm

/4 × 2

/8 × 6

/8 in.)

(w/h/d)

Mass Approx. 1.2 kg

(2 lb 10 oz.)

Supplied accessories Parts for installation and

connections (1 set)

Front panel case (1)

Card remote commander

RM-X114

Optional accessories Rotary commander

RM-X4S

Note

This unit cannot be connected to a digital

preamplifier or an equalizer.

Design and specifications are subject to change

without notice.

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION

23.2 watts per channel minimum continuous average power into

4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more

than 5% total harmonic distortion.

La page charge ...

Sony CDX-L600X Manuel utilisateur

Marque: Sony

Modèle: CDX-L600X

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sony CDX-L600X User manual

Sony CDX-L600X Manuel utilisateur

Sony CDX-L600X Manuel utilisateur

dans d''autres langues

Documents connexes