NAPOLEON BIP500RBNSS3 Mode d'emploi

Marque: NAPOLEON

Modèle: BIP500RBNSS3

Catégorie: Barbecues

Taper: Mode d'emploi

PG.27

www.napoleongrills.com

N415-0522 OCT 05.18

DANGER

IF YOU SMELL GAS:

• Shut o gas to the appliance.

• Exnguish any open ame.

• Open lid.

• If odor connues, keep away from the

appliance and immediately call your gas

supplier or re department.

APPLY SERIAL NUMBER LABEL FROM CARTON

Serial No.

XXXXXX000000

MODEL NO.

BIP500RB

This gas grill must be used only outdoors in a well-venlated space and must not be used inside a building,

garage, screened-in porch, gazebo or any other enclosed area.

WARNING! CABINET FRAME, CABINET AND COUNTER TOP MUST BE MADE FROM NON-COMBUSTIBLE MATERIAL.

Noce to Installer: Leave these instrucons with the grill owner for future reference.

Adults and especially children should be alerted to the hazards of high surface temperatures.

Young children should be supervised near the gas grill.

WARNING

Do not try to light this appliance without

reading the “LIGHTING” instrucons secon

of this manual.

Do not store or use gasoline or other

ammable liquids or vapors in the vicinity of

this or any other appliance. An L.P. cylinder

not connected for use must not be stored in

the vicinity of this or any other appliance.

If the informaon in these instrucons is

not followed exactly, a re or explosion may

result, causing property damage, personal

injury or death.

DO NOT DISCARD

Wolf Steel Ltd.

214 Bayview Drive,

Barrie, Ontario, CANADA L4N 4Y8

[email protected]

www.napoleongrills.com

N415-0522 OCT 05.18

*Conditions and Limitations

This Limited Warranty creates a warranty period as speciﬁed in the

aforementioned table, for any product purchased through an authorized NAPOLEON

dealer, and entitles the original purchaser to the speciﬁed coverage in respect of

any component replaced within the warranty period, either by NAPOLEON or an

authorized NAPOLEON dealer, to replace a component of such product that has

failed in normal private use as a result of a manufacturing defect. The “50% off”

indicated in the table means the component is made available to the purchaser at

a 50% discount off the regular retail price of the component for the period

indicated. This Limited Warranty does not cover accessories or bonus items.

For greater certainty, “normal private use” of a product means that the product:

has been installed by a licensed, authorized service technician or contractor, in

accordance with the installation instructions included with the product and all

local and national building and ﬁre codes; has been properly maintained; and has

not been used as a communal amenity or in a commercial application.

Similarly, “failure” does not include: over-ﬁring, blow outs caused by

environmental conditions such as strong winds or inadequate ventilation,

scratches, dents, corrosion, deterioration of painted and plated ﬁnishes,

discoloration caused by heat, abrasive or chemical cleaners or UV exposure,

chipping of porcelain enameled parts, or damages caused by misuse, accident,

hail, grease ﬁres, lack of maintenance, hostile environments such as salt or

chlorine, alterations, abuse, neglect or parts installed from other manufacturers.

Should deterioration of parts occur to the degree of non-performance (rusted

through or burnt through) within the duration of the warranted coverage, a

replacement part will be provided. The replacement component is the sole

responsibility of NAPOLEON deﬁned by this Limited Warranty; in no event will

NAPOLEON be responsible for installation, labor or any other costs or expenses

related to the re-installation of a warranted part, for any incidental, consequential,

or indirect damages or for any transportation charges, labor costs or export duties.

This Limited Warranty is provided in addition to any rights afforded to you by local

laws. Accordingly, this Limited Warranty imposes no obligation upon NAPOLEON to

keep parts in stock. Based on the availability of parts, NAPOLEON may at its

discretion discharge all obligations by providing a customer a prorated credit

towards a new product. After the ﬁrst year, with respect to this Limited Warranty

NAPOLEON may, at its discretion, fully discharge all obligations with respect to this

warranty by refunding to the original warranted purchaser the wholesale price of

any warranted but defective part(s).

The bill of sale or copy will be required together with a serial number and a

model number when making any warranty claims from NAPOLEON.

NAPOLEON reserves the right to have its representative inspect any product

or part prior to honoring any warranty claim. You must contact NAPOLEON

Customer Service or an authorized NAPOLEON dealer to obtain the beneﬁt of

the warranty coverage.

napoleongrills.com

Napoleon President’s Limited Lifetime Warranty

NAPOLEON products are designed with superior components and materials, and are assembled by trained craftsmen

who take great pride in their work. The burner and valve assembly are leak tested and test-fired at a quality test station.

This grill has been thoroughly inspected by a qualified technician before packaging and shipping to ensure that you,

the customer, receive the quality product you expect from NAPOLEON.

NAPOLEON warrants that components in your new NAPOLEON product will be free from defects in material and

workmanship from the date of purchase, for the following period:

Aluminum castings / stainless steel base ................................. Lifetime

Stainless steel lid ...................................................................... Lifetime

Porcelain enamel lid ................................................................. Lifetime

Stainless steel cooking grids ....................................................Lifetime

Stainless steel tube burners .....................................................10 years full coverage, plus 50% off for life

Porcelain-enameled cast iron cooking grids ............................. 10 years full coverage, plus 50% off for life

Stainless steel sear plates ........................................................ 5 years full coverage, plus 50% off for life

Stainless steel infrared rotisserie burner .................................. 5 years full coverage, plus 50% off for life

Ceramic infrared burners (excluding screen) ............................ 5 years full coverage, plus 50% off for life

All other parts ........................................................................... 2 years

www.napoleongrills.com

N415-0522 OCT 05.18

WARNING! Failure to follow these instrucons could result in property damage, personal injury

or death. Read and follow all warnings and instrucons in this manual prior to operang grill.

Safe Operang Pracces

• This gas grill must be assembled exactly according to the instrucons in the manual. If the grill was

store assembled, you must review the assembly instrucons to conrm correct assembly and perform

the required leak tests before operang the grill.

• Read the enre instrucon manual before operang the gas grill.

• This gas grill must be used only outdoors in a well-venlated space and must not be used inside a

building, garage, screened-in porch, gazebo or any other enclosed area.

• This gas grill must not be installed in or on recreaonal vehicles and/or boats.

• Do not locate unit in windy sengs. High winds adversely aect the cooking performance of the gas

grill.

• Under no circumstances should this gas grill be modied.

• Do not operate unit under overhead combusble construcon.

• Maintain proper clearance to combusbles, 20” (508mm) to rear of unit, 24” (610mm) to sides.

Addional clearance of 24” (610mm) is recommended near vinyl siding or panes of glass.

• Gas must be turned o at the gas supply valve when the gas grill is not in use.

• If the enclosure is to house a propane cylinder, the tank poron of the enclosure must be

venlated according to local codes, and must not have communicaon with the cavity used to

enclose the gas grill. A propane tank can not be stored below the gas grill.

• Do not aempt to use a cylinder that is not equipped with a QCC1 type connecon.

• When the propane cylinder is connected to the appliance, the gas grill and cylinder must be stored

outdoors in a well-venlated space.

• When the gas grill is to be stored indoors, the connecon between the propane cylinder and the gas

grill must be disconnected and the cylinder removed and stored outdoors in a well venlated space

out of reach of children. Disconnected cylinders must not be stored in a building, garage or any other

enclosed area. Natural gas units must be disconnected from the supply when being stored indoors.

• Inspect the fuel supply hose before each use. If there is evidence of excessive abrasion or wear or the

hose is cut, it must be replaced prior to using the gas grill with a replacement hose assembly specied

by the grill manufacturer.

• Leak test the unit before inial use, annually, and whenever any gas components are replaced.

• Follow lighng instrucons carefully when operang grill.

• Burner controls must be o when turning supply cylinder valve on.

• The lid is to be closed during the gas grill preheang period on all models except the BISZ300NFT/PFT

and the built-in side burner BISB245.

• The BISZ300NFT/PFT and the built-in side burner BISB245 are supplied with a at cover for storage

and protecon from the elements. Never place this cover on the grill while hot or operang. Allow

grill to cool completely before covering.

• Adults and especially children should be alerted to the hazards of high surface temperatures. Young

children should be supervised near the gas grill.

• Do not leave grill unaended when operang.

• Do not light burners with lid closed.

• Do not operate rear burner with main burners operang.

• Do not move grill when hot or operang.

• Keep any electrical supply cord and fuel supply hose away from any heated surfaces.

• Ensure sear plates are posioned properly according to sear plate installaon instrucons. The holes

must be towards the front of the gas grill (if applicable).

• Clean grease tray and sear plates regularly to avoid build-up, which could lead to grease res.

• Remove warming rack before lighng rear burner. The extreme heat will damage the warming rack.

• Inspect infrared burner venturi tube for spider webs and other obstrucons periodically. Clean the

tubes completely if you nd any such obstrucons.

• Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with heated unit. A large

temperature dierenal can cause chipping in the porcelain.

• Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with ceramic burners. A large

temperature dierenal can cause cracking in the ceramic le.

• Do not use a pressure washer to clean any part of the unit.

www.napoleongrills.com

N415-0522 OCT 05.18

General Informaon

his Gas Barbecue is cered under Canadian and American Naonal Standards, CSA 1.6-2015 and ANSI

Z21.58-2015 respecvely for Outdoor Gas Grills and should be installed to conform according to local

codes. In absence of local codes, install to the current CAN B149.1 Natural Gas and Propane Installaon

Code in Canada or to the Naonal Fuel Gas Code, ANSI Z223.1 in the United States.

If a rosserie motor is used, it must be electrically grounded in accordance with local codes or, in

absence of local codes, with the current CSA C22.1 Canadian Electrical Code in Canada or the Naonal

Electrical Code, ANSI/NFPA 70 in the United States.

WARNING: This product can expose you to chemicals including lead and lead compounds, which are

known to the State of California to cause cancer, and chemicals including di-n-butyl phthalate, which are

known to the State of California to cause birth defects or other reproducve harm. For more informaon

go to www.P65Warnings.ca.gov.

Propane Cylinder Specicaons

WARNING!

If these instrucons are not followed exactly, a re causing death or serious injury may

occur.

WARNING! Do not store a spare propane cylinder on the shelf beneath the barbecue.

If the gas grill is being supplied with propane from a portable cylinder, a regulator specied by the manu-

facturer must be used. The regulator must supply a pressure of 11 inches water column (0.39 PSI) to the

gas grill and have a QCC1 type ng. Cylinders to be used with this unit must be supplied with a QCC1

cylinder valve. A QCC1 cylinder has a posive seang connecon, which will not allow gas ow unl a

posive seal has been achieved. It is also equipped with an excess ow device. In order to aain full ow

to the grill, the valves must be in the o posion when the cylinder valve is turned on.

A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a

cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance

with the specicaons for LP-gas cylinders of the Naonal Standard of Canada, CAN/CSA-b339, Cylinders,

Spheres and Tubes for Transportaon of Dangerous Goods; and Commission, as applicable or the Speci-

caons for LP-Gas Cylinders of the U.S. Department of Transportaon (D.O.T.). Cart models have been

designed for use with a 20 lb (9.1 kg) size propane cylinder only (not supplied).

The propane cylinder must be provided with a cylinder connecon device compable with the connecon

for outdoor cooking appliances. The propane cylinder must be provided with a shut-o valve terminat-

ing in a propane cylinder valve type QCC1, and a safety relief device having direct communicaon with

the vapor space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and

the cylinder shall include a collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD

(overll protecon device). Do not store a spare LP-gas cylinder under or near this appliance. Never ll

the cylinder beyond 80 percent full. If the preceding informaon is not followed exactly, a re causing

death or serious injury may occur.

Gas Hook-Up Instrucons

WARNING! This grill is designed for non-combusble enclosures only, and must be installed and

serviced by a qualied installer to local codes.

WARNING! Cabinet frame, cabinet, and counter top must be made from non-combusble

material.

WARNING! As indicated on the rang plate, this gas grill is designed to operate with gas supply

pressures of 11” WC for Propane and 7” WC for Natural Gas. For installaons where the gas supply

pressure exceeds these requirements, a regulator must be installed upstream of the grill’s components.

If the gas supply pressure is lower than these requirements, the unit will be under-red and will not

reach the maximum temperatures. Ensure that the supply line size complies with local and/or naonal

installaon codes.

BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and

piping should be located as shown in the built-in instrucons. A exible metal connector is included to

simplify the installaon of the unit. Connect this exible metal connector to the are ng on the end of

the manifold. Connect the other end of the connector to the gas piping. Ensure that the connector does

not pass through a wall, oor, ceiling or paron, and is protected from damage. Do not use a hose to

connect the unit except to connect the cylinder regulator to the piping system. It must be connected with

www.napoleongrills.com

N415-0522 OCT 05.18

rigid pipe, copper tube or an approved exible metal connector which complies with Z21.24/ CSA 6.10 or

ANSI Z21.75/CSA 6.27.

The installaon must comply with CAN B149.1 Natural Gas and Propane installaon code in Canada, or

to the Naonal Fuel Gas code, ANSI Z223.1 in the United States. The gas supply pipe must be suciently

sized to supply the BTU/h specied on the rang plate, based on the length of the piping run. If installing

a side burner, a separate line must be branched o to the side burner unit and enter the side burner

opening at the specied locaon. If the enclosure is to house a propane cylinder, the tank poron of the

enclosure must be venlated according to local codes, and must not have communicaon with the cavity

used to enclose the gas grill. A propane cylinder can not be stored below the gas grill.

BUILT IN CYLINDER ENCLOSURES: Built in cylinder enclosures which completely enclose the cylinder must

have both of the following:

1. At least one unobstructed venlaon opening on the exposed exterior side of the enclosure located

within 5 in (127mm) of the top of the enclosure. The opening must have a total free area of more than 20

(130 cm

) for a 20 lb (9.1 kg) cylinder and 30 in

(195 cm

) for a 30 lb (13.6 kg) cylinder.

2. At least one venlaon opening on the exposed, exterior side of the enclosure located 1 in (25.4 mm) or

less from the oor level. The opening must have a total free area of more than 10 in

(65 cm

) for a 20 lb

(9.1 kg) cylinder and 15 in

(100 cm

) for a 30 lb (13.6 kg) cylinder. The upper edge must be no more than

5 in (127 mm) above the oor level.

Every opening must be large enough to permit the entrance of a 1/8 in (3.2 mm) rod.

WARNING!

• The cylinder valve(s) must be readily accessible for hand operaon. A door on the enclosure to gain

access to the cylinder valves is acceptable, provided it is non-locking and can be opened without the

use of tools.

• The enclosure for the LP-gas cylinder must isolate the cylinder from the burner compartment to

provide shielding from radiaon, a ame barrier, and protecon from foreign material, such as hot

drippings. The enclosure cannot be located directly below the grill.

• There must be a minimum clearance of 2 in (51 mm) between the oor of the LP-gas cylinder

enclosure and the ground.

• The enclosure must be designed so that the LP-gas cylinder can be connected, disconnected and

the connecons inspected and tested outside the cylinder enclosure. Any connecons that can

be disturbed when installing the cylinder in the enclosure must be accessible for tesng inside the

enclosure.

CYLINDER SIZE OPENING A AREA OPENING B AREA

20 lb (9.1kg)

20in

(130cm

) 10in

(65cm

)

30 lb (13.6kg)

30in

(195cm

) 15in

(100cm

)

5” (127mm)

MAXIMUM

1” (25.4mm)

MAXIMUM

OPENING

2” (51mm)

MINIMUM

PARTITION TO ISOLATE

CYLINDER FROM GRILL

NON LOCKING DOOR

34” (864mm)

RECOMMENDED

5” (127mm)

MAXIMUM

www.napoleongrills.com

N415-0522 OCT 05.18

Leak Tesng Instrucons

WARNING! A leak test must be performed annually and each me a cylinder is hooked up or if a

part of the gas system is replaced.

WARNING! Never use an open ame to check for gas leaks. Be certain no sparks or open ames

are in the area while you check for leaks. Sparks or open ames will result in a re or explosion,

damage to property, serious bodily injury, or death.

Leak tesng: This must be done before inial use, annually, and whenever any gas components are

replaced or serviced. Do not smoke while performing this test, and remove all sources of ignion. See Leak

Tesng Diagram for areas to check. Turn all burner controls to the o posion. Turn gas supply valve on.

Brush a half-and-half soluon of liquid soap and water onto all joints and connecons of the regulator,

hose, manifolds and valves.

Bubbles will indicate a gas leak. Either ghten the loose joint or have the part replaced with one

recommended by the Napoleon Customer Soluons department and have the grill inspected by a cered

gas installer.

If the leak cannot be stopped, immediately shut o the gas supply, disconnect it, and have the grill

inspected by a cered gas installer or dealer. Do not use the grill unl the leak has been corrected.

BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and

piping should be located as shown in the built-in instrucons. A exible metal connector is included to

simplify the installaon of the unit. Connect this connector to the are ng on the end of the manifold.

Connect the other end of the connector to the gas piping. Ensure that the connector does not pass

through a wall, oor, ceiling or paron, and is protected from damage. Do not use a hose to connect the

unit. It must be connected with rigid pipe, copper tube or an approved exible metal connector which

complies with Z21.4 /CSA 6.10 or ANSI Z21.75/CSA 6.27.

The installaon must comply with CAN B149.1 Natural Gas and Propane Installaon Code in Canada, or

to the Naonal Fuel Gas Code, ANSI Z223.1 in the United States. The gas supply pipe must be suciently

sized to supply the BTU/h specied on the rang plate, based on the length of the piping run. If installing

a side burner, a separate line must be branched o to the side burner unit and enter the side burner

opening at the specied locaon.

WARNING! Built in units are supplied with a drip pan which holds only a minimal amount of

grease. To prevent grease res, the pan must be cleaned aer each use.

WARNING! Access must be provided to the inside of the enclosure to make gas connecons.

DANGER! Read all instrucons carefully before operang the grill. Failure to follow these

instrucons exactly could result in a re causing serious injury or death. The enre installaon must be

leak tested before operang the grill.

STOP

www.napoleongrills.com

N415-0522 OCT 05.18

Lighng Instrucons

O Posion

WARNING! Open lid.

WARNING! Ensure all burner controls are in the o posion. Slowly turn on the gas

supply valve.

Main Burner

Lighng

Rear Burner Lighng

(if equipped)

Side Burner Lighng

(oponal)

1. Open grill lid. 1. Open grill lid. 1. Open burner cover.

2. Push and turn any main burner knob

slowly to the high posion. If the pilot

lights, connue to push down on the

control knob unl the burner lights and

then release.

2. Remove warming rack. 2. Turn side burner control to high

posion.

3. If the pilot does not ignite, then

immediately turn the control knob

back to the ‘o posion and repeat

step 2 several mes.

3. Turn rear burner control to

high posion.

3. Press and hold

igniter buon unl burner lights, or

light by match.

4. If the pilot and burner will not ignite

within 5 seconds, turn the control knob

to the ‘o’ posion and wait 5 minutes

for any excess gas to dissipate. Either

repeat steps 2 and 3 or light with a

match.

4. Press and hold

igniter buon unl burner lights,

or light by match.

4. If ignion is not

immediate, turn burner control o.

Wait 5 minutes. Repeat.

5. If lighng the unit with a match, clip

the match into the supplied lighng

rod. Hold the lit match down through

the grill and sear plate while turning

the corresponding burner valve to

high.

5. If ignion is not immediate,

turn burner control o. Wait 5

minutes. Repeat.

WARNING! The propane cylinder is equipped with an excess ow device. Unless all burners are

turned o prior to turning the cylinder on, only small ames and low heat will be achievable.

WARNING! Do not use rear burner while operang main burner.

Le

Burner

Right

Burner

Le Centre

Burner

Right Centre

Burner

Rear

Burner

Igniter

Lights

www.napoleongrills.com

N415-0522 OCT 05.18

Cooking Instrucons

Inial Lighng: When lit for the rst me, the gas grill emits a slight odor. This is a normal temporary

condion caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and

does not occur again. Simply run the main burners on high for approximately one-half hour.

Do not locate this gas grill in windy sengs. High winds adversely aect the cooking performance of the

gas grill. In extreme circumstances when consistent high winds come from directly behind the unit, heat

can vent underneath the control panel. This may cause the control panel to become extremely hot to

touch and the knobs to deform.

Napoleon oers an oponal wind deector illustrated below. Install this wind deector to help prevent

the possibility of improper heat build up.

NOTE! Napoleon is not responsible for: over ring, blow outs caused by environmental condions

such as strong winds, or inadequate venlaon.

www.napoleongrills.com

N415-0522 OCT 05.18

Main Burner Use: When searing foods, we recommend preheang the grill by operang all main burners

in the high posion with the lid closed for approximately 10 minutes. Food cooked for short periods of

me (sh, vegetables) can be grilled with the lid open. Cooking with the lid closed will ensure higher, more

even temperatures that can reduce cooking me and cook meat more evenly. Food that has a cooking

me longer than 30 minutes, such as roasts, can be cooked indirectly (with the burner lit opposite to the

food placement). When cooking very lean meats, such as chicken breasts or lean pork, the grids can be

oiled before pre-heang to reduce scking. Cooking meat with a high degree of fat content can create

are-ups. Either trim the fat or reduce temperatures to inhibit this. Should a are-up occur, move food

away from the ames and reduce the heat. Leave the lid open. See Your All Season Grill cookbook by

Napoleon for more detailed instrucons.

Rear Burner Use (If Equipped): Remove the warming rack prior to use, the extreme heat will damage the

warming rack. Cooking grids should also be removed if they interfere with the rosserie. The rear burner

is designed to be used in conjuncon with the rosserie kit available from your dealer. See the rosserie

kit assembly instrucons.

To use the counterbalance - remove the rosserie motor from the gas grill. Place the spit with meat being

cooked across the hangers inside the grill. The meat will naturally hang with the heavy side down. Tighten

the counterbalance arm and weight so the arm is facing up. Slide the counterweight in or out to balance

the load and ghten in place. Re-install the motor and begin cooking. Place a metal dish underneath the

meat to collect drippings for basng and naturally delicious gravy. Basng liquid may be added as required.

To seal in juices, rst operate rear burner on high unl brown, then reduce the heat to thoroughly cook

foods. Keep the lid closed for best results. Your roasts and fowl will brown perfectly on the outside and

stay moist and tender on the inside. For example, a 3 pound chicken on the rosserie will be done in

approximately 1½ hours on medium to high. Search Grill Master Recipes at www.napoleongrills.com/

recipes for “rosserie”.

ATTENTION! Barbecue sauce and salt can be corrosive and will cause rapid deterioraon of

the gas grill components unless cleaned regularly. When nished cooking disassemble rosserie

components, wash thoroughly with warm soapy water and store indoors.

Direct Cooking: Place food to be cooked on the grill directly over the heat. This method is generally used

for searing or for foods that do not require prolonged cooking mes such as hamburgers, steaks, chicken

pieces, or vegetables. The food is rst seared to trap-in the juices and avor, and then the temperature is

lowered to nish cooking the food to your preference.

Indirect Cooking: With one or more burners operang, place food to be cooked on the grill over a burner

that is not operang. The heat circulates around the food, cooking slowly and evenly. Cooking with this

method is much the same as cooking in your oven and is generally used for larger cuts of meats such

as roasts, chickens or turkeys, but can also be used for cooking foods that are prone to are-ups or for

smoking foods. Lower temperatures and slower cooking mes result in tender foods.

www.napoleongrills.com

N415-0522 OCT 05.18

WARNING! Always wear protecve gloves and safety glasses when servicing your grill.

WARNING! To avoid the possibility of burns, maintenance should be done only when the grill is

cool. Avoid unprotected contact with hot surfaces. Ensure all burners are turned o. Clean grill in an

area where cleaning soluons will not harm decks, lawns, or paos. Do not use oven cleaner to clean

any part of this gas grill. Do not use a self-cleaning oven cleaner to clean cooking grids or any other

parts of the gas grill. Barbecue sauce and salt can be corrosive and will cause rapid deterioraon of the

gas grill components unless cleaned regularly.

Cleaning Instrucons

Note: Stainless steel tends to oxidize or stain in the presence of chlorides and suldes, parcularly in

coastal areas and other harsh environments, such as the warm, highly humid atmosphere around pools

and hot tubs. These stains could be perceived as rust, but can be easily removed or prevented. To provide

stain prevenon and removal, wash all stainless steel and chrome surfaces every 3-4 weeks or as oen as

required with fresh water and/or stainless steel cleaner.

Grids And Warming Rack: The grids and warming rack are best cleaned with a brass wire brush during

the pre-heang period. Steel wool can be used for stubborn stains. It is normal that stainless grids (if

equipped) will discolor permanently from regular usage due to the high temperature of the cooking

surface.

Control Panel:

The control panel text is printed directly on the stainless steel and with proper maintenance

will remain dark and legible. To clean the panel, use only warm soapy water. Never apply abrasive cleaners on

any stainless surfaces, especially the printed portion of the control panel or the printing will gradually rub off.

Cleaning Inside The Gas Grill: Remove the cooking grids. Use a brass wire brush to clean loose debris from

the casng sides and underneath the lid. Scrape the sear plates with a puy knife or scraper, and use a

wire brush to remove the ash. Remove the sear plates and brush debris from the burners with the brass

wire brush. Sweep all debris from inside the gas grill into the drip pan.

WARNING! Built in units are supplied with a drip pan which holds only a minimal amount of

grease. To prevent grease res, the pan must be cleaned aer each use.

Drip Pan: Accumulated grease is a re hazard. Clean the drip pan aer each use to avoid grease buildup.

Grease and excess drippings pass through to the drip pan, located beneath the gas grill. To clean the drip

pan, slide the drip pan free of the grill. Never line the drip pan with aluminum foil, sand or any other

material as this could prevent the grease from owing properly. The pan should be scraped out with a

puy knife or scraper.

Cleaning The Outer Grill Surface: Do not use abrasive cleaners or steel wool on any painted, porcelain or

stain

less steel parts of your Napoleon Grill. Doing so will scratch the nish. Exterior grill surfaces should be

cleaned with warm soapy water while the metal is sll warm to the touch. To clean stainless surfaces, use

a stainless steel or a non-abrasive cleaner. Always wipe in the direcon of the grain. Over me, stainless

steel parts discolor when heated, usually to a golden or brown hue. This discoloraon is normal and does

not aect the performance of the grill. Porcelain enamel components must be handled with addional

care. The baked-on enamel nish is glass-like, and will chip if struck. Touch-up enamel is available from

your Napoleon Grill dealer.

www.napoleongrills.com

N415-0522 OCT 05.18

WARNING! Always wear protecve gloves and safety glasses when cleaning your grill.

WARNING! Turn o the gas at the source and disconnect the unit before servicing. To avoid the

possibility of burns, maintenance should be done only when the grill is cool. A leak test must be

performed annually and whenever any component of the gas train is replaced or gas smell is present.

Maintenance Instrucons

We recommend this gas grill be thoroughly inspected and serviced annually by a qualied service person.

At all mes keep the gas grill area free from combusble materials, gasoline and other ammable vapors

and liquids. Do not obstruct the ow of venlaon and combuson air. Keep the cylinder enclosure

venlaon openings (located on the cart sides and at the front and back of the boom shelf) free and

clear from debris.

Light Blue

Yellow Tipping

Dark Blue

Burner

Burner Port

Approximately

1/2” (13mm)

Combuson Air Adjustment: (This must be done by a qualied gas installer.) The air shuer is factory set

and should not need adjusng under normal condions. Under extreme eld condions, adjustments

might be required. When the air shuer is adjusted correctly the ames will be dark blue, pped with

light blue and occasionally yellow.

• With too lile air ow to the burner, the ames are lazy yellow and can produce soot.

• With too much air ow, the ames li erracally and can cause dicules when lighng.

Adjusng the air shuer:

1. Remove cooking grids and sear plates and leave lid open. You may have to open the door or remove

the top drawer (if equipped) to access the air-shuer screw located at the mouth of the burner. The back

cover must be removed for rear tube burner air shuer adjustment.

Loosen air-shuer lock screw and open or close air shuer as required. The normal opening sengs are:

Main Tube Burner Propane 1/2″ (13mm) Rear Tube Burner Propane Full Open

Natural 3/8″ (10mm) Natural 1/8″ (3mm)

*Infra-Red burners have no air adjustment.

3. Light the burners and set to high. Visually inspect burner ames. When the shuers are set correctly,

turn burners o, ghten locking screws, and replace removed parts. Ensure that the insect screens are

installed.

www.napoleongrills.com

N415-0522 OCT 05.18

Burner: The burner is made from heavy wall 304 stainless steel, but extreme heat and a corrosive

environment can cause surface corrosion to occur. This can be removed with a brass wire brush.

CAUTION! Beware of Spiders.

Spiders and insects are aracted to the smell of propane and natural gas. The burner is equipped with an

insect screen on the air shuer, which reduces the likelihood of insects building nests inside the burner

but does not enrely eliminate the problem. A nest or web can cause the burner to burn with a so yellow

or orange ame or cause a re (ashback) at the air shuer underneath the control panel. To clean the

inside of the burner, it must be removed from the gas grill: Remove the screw (s) that aaches the burner

to the back wall. Slide the burner back and up wards to remove. Cleaning: Use a exible venturi tube brush

to clean the inside of the burner. Shake any loose debris from the burner through the gas inlet. Check the

burner ports and valve orices for blockages. Burner ports can close over me due to cooking debris and

corrosion, use an opened paperclip or the supplied port maintenance bit to clean them. Drill out blocked

ports using this drill bit in a small cordless drill. The ports are easier to clean if the burner is removed from

the grill, but it can also be done with the burner installed. Do not ex the drill bit when drilling the ports,

as this will cause the drill bit to break. This drill is for burner ports only, not for the brass orices (jets)

which regulate the ow into the burner. Take care not to enlarge the holes. Ensure the insect screen is

clean, ght, and free of any lint or other debris.

Reinstallaon: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when

installing. Replace sear plate mount and / or ghten screws to complete reinstallaon.

WARNING! Regulator Hose (when applicable): Check for abrasions’, melng, cuts, and cracks in the

hose. If any of these condions exist, do not use the gas grill. Have the part replaced by your Napoleon

Gas Grill dealer or qualied gas installer.

WARNING! When reinstalling the burner aer cleaning it is very

important that the valve/orice enters the burner tube before lighng

your gas grill. If the valve is not inside the burner tube a re or explosion

could occur.

Aluminum Casngs: Clean casngs periodically with warm soapy water. Aluminum will not rust, but high

temperatures and weathering can cause oxidaon to occur on aluminum surfaces. This appears as white

spots on the casngs. To renish these areas, clean rst and sand lightly with ne sandpaper. Wipe the

surface to remove any residue and paint with high temperature barbecue paint. Protect surrounding

areas from over-spray. Follow the manufacture’s direcons for curing.

www.napoleongrills.com

N415-0522 OCT 05.18

Troubleshoong

Problem Possible Causes Soluon

Low heat / Low ame

when valve turned to

high.

For propane - improper lighng

procedure.

For natural gas - undersized supply

line.

For both gases - improper preheang.

Ensure lighng procedure is followed carefully.

All gas grill valves must be in the o posion

when the tank valve is turned on. Turn tank

on slowly to allow pressure to equalize. See

lighng instrucons.

Pipe must be sized according to installaon

code.

Preheat grill with both main burners on high

for 10 to 15 minutes.

Excessive are-ups/

uneven heat.

Sear plates installed incorrectly.

Improper preheang.

Excessive grease and ash build on sear

plates and in drip pan.

Ensure sear plates are installed with the holes

towards the front and the slots on the boom.

See assembly instrucons.

Preheat grill with both main burners on high

for 10 to 15 minutes.

Clean sear plates and drip pan regularly. Do

not line pan with aluminum foil. Refer to

cleaning instrucons.

Burners burn with yellow

ame, accompanied by

the smell of gas.

Possible spider web or other debris, or

improper air shuer adjustment.

Thoroughly clean burner by removing. See

general maintenance instrucons. Open air

shuer slightly according to combuson air

adjustment instrucons. (This must be done

by a qualied gas installer.)

Flames li away from

burner, accompanied

by the smell of gas, and

possibly dicules in

lighng.

Improper air shuer adjustment. Close air shuer slightly according to

combuson air adjustment instrucons. (This

must be done by a qualied gas installer.)

Rear and Side burners

will not light with the

igniter, but will light with

a match.

Dead baery / or installed incorrectly.

Loose electrode wire or switch

terminal wires.

Liing ames on burner.

Replace with premium heavy duty baery.

Check that electrode wire is rmly pushed

onto the terminal on the back of the igniter.

Check that the lead wires from the module

to the ignion switch (if equipped) are rmly

pushed onto their respecve terminals.

Close air shuer slightly - see previous

problem.

Main burner will not light

with the igniter, but will

light with a match.

Jet-re outlet is dirty or clogged. Clean jet-re outlet with a so bristle brush.

Humming regulator. Normal occurrence on hot days. This is not a defect. It is caused by internal

vibraons in the regulator and does not aect

the performance or safety of the gas grill.

Humming regulators will not be replaced.

Burners will not cross

light each other.

Dirty or corroded cross light brackets. Clean or replace as required.

“Paint” appears to be

peeling inside lid or

hood.

Grease build-up on inside surfaces. This is not a defect. The nish on the lid and

hood is porcelain, and will not peel. The

peeling is caused by hardened grease, which

dries into paint-like shards, that ake o.

Regular cleaning will prevent this. See cleaning

instrucons.

www.napoleongrills.com

N415-0522 OCT 05.18

Problem Possible Causes Soluon

Burner output on “high”

seng is too low.

(Rumbling noise and

uering blue ame at

burner surface.)

Lack of gas.

Supply hose is pinched.

Dirty or clogged orice.

Spider webs or other maer in venturi

tube.

Propane regulator in “low ow” state.

Check gas level in propane cylinder.

Reposion supply hose as necessary.

Clean burner orice.

Clean out venturi tube.

Ensure lighng procedure is followed carefully.

All gas grill valves must be in the o posion

when the tank valve is turned on. Turn tank

on slowly to allow pressure to equalize. See

lighng instrucons.

Infrared burner (if

equipped) ashes back

(during operaon the

burner abruptly makes

a loud “whoosh” sound,

followed by a connuous

blow-torch type sound

and grows dim.)

Ceramic les overloaded with grease

drippings and build-up. Ports are

clogged.

Burner overheated due to inadequate

venlaon (too much grill surface

covered by griddle or pan.)

Cracked ceramic le.

Leaking gasket surrounding the

ceramic le, or a weld failure in the

burner housing.

Turn burner o and allow to cool for at least

two minutes. Relight burner and burn on high

for at least ve minutes or unl the ceramic

les are evenly glowing red.

Ensure that no more than 75% of the grill

surface is covered by objects or accessories.

Turn burner o and allow to cool for at least

two minutes, then relight.

Allow burner to cool and inspect very closely

for cracks. If any cracks are found, contact

your authorized Napoleon dealer to order a

replacement burner assembly.

Contact your authorized Napoleon dealer for

instrucons on ordering a replacement burner

assembly.

www.napoleongrills.com

N415-0522 OCT 05.18

KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY.

Ordering Replacement Parts

Warranty Informaon

MODEL:

DATE OF PURCHASE:

SERIAL NUMBER:

(Record informaon here for easy reference)

For replacement parts and warranty claims, contact the Napoleon dealer where the product was purchased.

Before contacng the dealer, check the Napoleon Grills Website for more extensive cleaning, maintenance,

troubleshoong and parts replacement instrucons at www.napoleongrills.com.

To process a claim, the following informaon is required:

1. Model and serial number of the unit.

2. Part number and descripon.

3. A concise descripon of the problem (‘broken’ is not sucient).

4. Proof of purchase (photocopy of the invoice).

In some cases, Napoleon could request to have the parts returned to the factory for inspecon before

providing replacement parts.

Before contacng Napoleon dealer, please note that the following items are not covered by the warranty:

• Costs for transportaon, brokerage or export dues.

• Labour costs for removal and reinstallaon.

• Costs for service calls to diagnose problems.

• Discolouraon of stainless steel parts.

• Part failure due to lack of cleaning and maintenance, or use of improper cleaners (oven

cleaner or other harsh chemicals).

www.napoleongrills.com

N415-0522 OCT 05.18

Geng Started

1. Remove all cart panels, hardware, and grill head from the carton. Raise lid and remove any

components packed inside. Use the parts list to ensure all necessary parts are included.

2. Do not destroy packaging unl the grill has been fully assembled and operates to your sasfacon.

3. Assemble the grill where it is to be used, lay down cardboard or a towel to protect parts from being

lost or damaged while assembling.

4. Most stainless steel parts are supplied with a protective plastic coating that must be removed

prior to using the grill. The protective coating has been removed from some of the parts

during the manufacturing process and may have left behind a residue that can be perceived as

scratches or blemishes. To remove the residue, vigorously wipe the stainless steel in the same

direction as the grain.

5. Follow all instrucons in the order that they are laid out in this manual.

6. Two people are required to set the grill head into the enclosure.

If you have any quesons about assembly or grill operaon or if there are damaged or missing parts

please call our Customer Soluons Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern

Standard Time).

CAUTION! During unpacking and assembly we recommended you wear work gloves and safety

glasses for your protecon. Although we make every eort to make the assembly process as problem

free and safe as possible, it is characterisc of fabricated steel parts that the edges and corners might

be sharp and could cause cuts if handled incorrectly.

TOOLS REQUIRED FOR ASSEMBLY (tools not included)

WARNING! Construcon materials and masonry dust may cause surface damage to units and

accessories. The best opon is to install components aer all construcon has been completed and

the jobsite has been thoroughly cleaned. If the components must be installed prior to the construcon

being completed, then exposed surfaces need to be covered to prevent corrosion. All surfaces must

be cleaned when construcon is completed. Do not use muriac acid to clean masonry materials

from any surfaces. The lime contained in some construcon materials is extremely corrosive. During

its curing period, (1 - 2 months) it is recommended that a stainless steel polish or wax (car wax is

acceptable) be applied to prevent direct contact of the lime materials.

3/8” (10 mm)

www.napoleongrills.com

N415-0522 OCT 05.18

BUILT-IN UNIT OPENING DIMENSIONS

MODEL OPENING DIMENSIONS NOTES

W D H

BIP500RB 30 3/4”

781mm

20 5/8”

524mm

8 7/8”

225mm

SIDE BURNER 12 3/4”

324mm

16 1/2”

419mm

4 1/2”

114mm

OPENING OF AT LEAST 5 SQ IN MUST BE PROVIDED FOR COMBUS

TION

AIR FOR SIDE BURNER.

MINIMUM 10 SQ IN OF

VENTILATION REQUIRED

ON EACH END OF CABINET

5” (127mm)

GAS INLET OPENING

OUTDOOR GFI ELECTRICAL OUTLET

REC

OMMENDED - LOCATE ON SAME SIDE

OF GRILL AS ROTISSERIE BRACKET.

1¾”

(44mm)

1¾”

(44mm)

BUILT-IN SIDEBURNER

GAS INLET OPENING

NON-COMBUSTIBLE MATERIAL

Note: Accessory frames

overlap opening by 1 ¾”

on all 4 sides.

WARNING! CABINET FRAME, CABINET AND COUNTER TOP

MUST BE MADE FROM NON-COMBUSTIBLE MATERIAL.

WARNING! A propane tank can not be stored

below the gas grill.

WARNING! This grill is designed for Non-combusble enclosures only, and must be installed and

serviced by a qualied installer to local codes.

WARNING! Use only non-combusble materials (cered to ASTM E-136) such as steel studs,

cement board, ceramic le, marble, paint etc. When adding nishing materials to the appliance.

Do not use wood or drywall.

34” (864mm)

RECOMMENDED

4” (102mm)

OPENING FOR WIRES

1” (25.4mm)

www.napoleongrills.com

N415-0522 OCT 05.18

BUILT-IN ACCESSORY OPENING DIMENSIONS

OPENING DIMENSIONS

PART # DESCRIPTION PICTURE W H D

N370-0361 PF STYLE STAINLESS STEEL DOOR 17” (432mm) 23 ¼” (591mm)

N370-0359 PF STYLE STAINLESS STEEL SINGLE

DRAWER

17 ¼” (438mm) 6 ¾” (171mm) 23” (584mm)

N370-0360 PF STYLE STAINLESS STEEL TRIPLE

DRAWER

17 ¼” (438mm) 22 ¾” (578mm) 23” (584mm)

N370-0502-1

N370-0503-1

DOUBLE DOOR SMALL

DOUBLE DOOR LARGE

* FRAMES PROTRUDE FROM FACE

OF CABINET BY ¾”

28 ¼” (718mm)

38 ¼” (959mm)

20 ¼” (514mm)

N370-0504

N370-0505

SIDE BURNER PROPANE

SIDE BURNER NATURAL

12 ¾” (324mm) 4 ½ ” ( 1 1 4 m m )

minimum

16 ½” (419mm)

www.napoleongrills.com

N415-0522 OCT 05.18

BI ACCESSORY DRAWER INSTRUCTIONS

BI ACCESSORY DOOR INSTRUCTIONS

1. Unpack the drawer frame assembly.

2. Remove the drawers from the enclosure by fully extending them and then liing up to remove them from the slides.

3. Shim the opening to ensure that the enclosure ts snuggly into the opening. Ensure that the side shims are located

at the same height as the enclosure mounng holes. The boom of the opening may need to be shimmed as well to

ensure that the front of the enclosure is plumb.

4. Once the enclosure is level and square, fasten into place. (Fasteners not included).

5. Re-install the drawers by pping the back of the drawer down into the slide. Once the wheels are inserted into the

slide, lower the front of the drawer unl it is level, then push in. Note: if the enclosure is installed with shims that are

too thick, the wheel will not engage into the slide. The shim thickness will need to be reduced.

6. Remove the protecve coang from all remaining surfaces.

1. Unpack the door and frame.

a. For the curved stainless steel doors, remove the door(s) from the frame by liing the door while holding on to the

pivot rod. This will allow the pivot rod to come out of the hole on the boom of the frame. Once the pivot is removed

from the boom hole, the enre door can be dropped and removed from the frame.

b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on the

hinge furthest away from the door. This will allow the hinge to separate.

c. For double door kits N370-0502-1/N370-0503-1, refer to the instucons included with the door kit.

2. Center the frame in the opening. Mark the locaon of the pivot holes, top and boom. Remember on the PT600

double doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods. Once all pivot holes

are marked, remove the frame and using a 3/8” drill bit, drill out the clearance holes for the pivot rod. These clearance

holes should be at least 1/2” deep. Aer the holes are complete, you may once again center the frame in the opening.

Starng with the hinged side, shim between the frame and side wall of the opening. Ensure the shims are close to the

hinge on the PF style doors. When the frame side wall is plumb, fasten it to the cabinet with screws (not provided).

Aach the other side of the frame in the same fashion, ensuring the frame is square.

3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and boom of the

frame. The curved stainless steel double door frame must be fastened in the center both at the top and boom.

4. Once the frame has been secured and checked for squareness, the door can be re-installed.

5. Remove the protecve coang from all remaining surfaces.

www.napoleongrills.com

N415-0522 OCT 05.18

BIP500RB BUILT-IN INSTRUCTIONS

This grill is designed for masonry, NON-COMBUSTIBLE enclosures only, and must be installed and serviced by a

qualied installer to local codes.

1. Aach the side mounng brackets to each side of the grill using (4) 1/4 - 20 x 7/8” screws (N570-0087). Pre-installed

at factory.

2. Lay the rear trim piece across the back of the opening. To keep it in place, a dab of silicone may be applied to each

wing of the rear trim.

3. Lower the unit in place, the wings on the rear trim should be under the side mounng brackets. Connect the ex

supply line to the ng at the end of the manifold.

4. The enre installaon must be leak tested before operang the unit.

N570-0087 (1/4” -20 X 7/8”)

(Pre-installed at factory.)

APPLY A DAB OF SILICONE

TO EACH FLANGE TO

SECURE IN PLACE.

La page est en cours de chargement...

NAPOLEON BIP500RBNSS3 Mode d'emploi

Marque: NAPOLEON

Modèle: BIP500RBNSS3

Catégorie: Barbecues

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON BIP500RBNSS3 User guide

NAPOLEON BIP500RBNSS3 Mode d'emploi

NAPOLEON BIP500RBNSS3 Mode d'emploi

dans d''autres langues

Documents connexes