Sharp KC-850E Le manuel du propriétaire

OSAKA, JAPAN

SHARP CORPORATION

R

* Plasmacluster is a

trademark of Sharp

Corporation.

KC-840E

KC-850E

KC-860E

ČISTIČKA VZDUCHU

s funkcí zvlhčování

NÁVOD K OBSLUZE

ČISTIČKA VZDUCHU

s funkciou zvlhčovania

NÁVOD NA POUŽITIE

LÉGTISZTÍTÓ

párásító funkcióval

HASZNÁLATI ÚTMUTATÓ

ОЧИСНИК ПОВІТРЯ

з Функцією Зволожування

ПОСІБНИК З ЕКСПЛУАТАЦІЇ

Free standing type

Freistehendes Modell

Type mobile

Vrijstaand type

Modello strutturalmente indipendente

Tipo vertical sin soporte

Тип установки: отдельностоящий

Volně stojící

Voľne stojaca

Különálló típus

Вільностоячий тип

AIR PURIFIER

with Humidifying Function

OPERATION MANUAL

LUFTREINIGER

mit Befeuchtungsfunktion

BEDIENUNGSANLEITUNG

Puriﬁ cateur d’air avec fonction

d’humidiﬁ cation

MANUEL D’UTILISATION

LUCHTREINIGER

met luchtbevochtiger

GEBRUIKSAANWIJZING

PURIFICATORE D’ARIA

con funzione di umidiﬁ cazione

MANUALE D’USO

PURIFICADOR DE AIRE

con Función de humidiﬁ cación

MANUAL DE USO

DUTITASPA

RUS

Воздухоочиститель с

функцией увлажнения

РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ

FRE

SLK

UKR

JPN

Printed in China

TINS-A384KKRZ 09J-

CN 1

HUN CZE

GER ENG

KC-840E

KC-850E

KC-860E

NOTE

HEPA Filter

Washable Deodorizing Filter

Pre-Filter

The air puriﬁ er draws in room air from the air intake, passes the air through a Pre-Fil-

ter, a Washable Deodorizing Filter and a HEPA Filter inside of the unit, then discharg-

es the air through the air outlet. The HEPA Filter can remove 99.97% of dust particles

as small as 0.3 microns that pass through the ﬁ lter and also helps absorb odours. The

Washable Deodorizing Filter gradually absorbs odours as they pass through the ﬁ lter.

Some odours absorbed by the ﬁ lters may break down over time, resulting in additional

odour. Depending on the usage environment, especially when the product is used in

extreme environments (significantly more severe than normal household use), this

odour may become strong in a shorter period than expected. If the odour persists, the

ﬁ lters should be replaced.

• The air puriﬁ er is designed to remove air-suspended dust and odour, but not harmful gases (for

example, carbon monoxide contained in cigarette smoke). If the source of the odour still exists, the

air puriﬁ er may not completely remove the odour.

(Common illustration has used “KC-850E”.)

Please read before operating your new Air Puriﬁ er

E-1

ENG

ENGLISH

Thank you for purchasing this SHARP Air

Purifier. Please read this manual carefully

before using the air puriﬁ er.

After reading, keep the manual in a conven-

ient location for future reference.

FEATURES

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

...

E-2

• WARNING ..................................................

E-2

• CAUTIONS CONCERNING OPERATION .

E-3

• INSTALLATION GUIDELINES ....................

E-3

• FILTER GUIDELINES ................................

E-3

PART NAMES

.............................................

E-4

• ILLUSTRATIVE DIAGRAM .........................

E-4

• BACK ..........................................................

E-4

• FRONT MONITOR .....................................

E-5

PREPARATION FOR USE ............................

E-6

• FILTER INSTALLATION .............................

E-6

• REFILLING WATER TANK .........................

E-7

OPERATION

...............................................

E-8

• MAIN UNIT DISPLAY .................................

E-8

• CLEAN AIR & HUMIDIFY MODE ...............

E-8

• CLEAN AIR MODE .....................................

E-9

• CLEAN ION SHOWER MODE ...................

E-9

• FAN SPEED BUTTON ................................

E-9

• Plasmacluster ON/OFF BUTTON .............

E-10

• LIGHTS CONTROL BUTTON ..................

E-10

• WATER SUPPLY INDICATOR LIGHT ......

E-10

• ADJUSTMENT OF SENSOR

DETECTION SENSITIVITY ......................

E-10

CARE AND MAINTENANCE

.................

E-11

• FILTER INDICATOR LIGHT .....................

E-11

• BACK PANEL AND SENSORS ................

E-11

• UNIT ........................................................

E-11

• WATER TANK ...........................................

E-12

• WASHABLE DEODORIZING

FILTER CARE ..........................................

E-12

• HUMIDIFYING TRAY ...............................

E-13

• HUMIDIFYING FILTER .............................

E-14

•

FILTER REPLACEMENT GUIDELINES

......

E-15

TROUBLESHOOTING

............................

E-16

SPECIFICATIONS

....................................

E-18

INFORMATION ON PROPER DISPOSAL

..

E-19

Unique Combination of Air Treatment

Technologies

Triple Filtration System + Plasmacluster

+ Humidiﬁ cation

TRAPS DUST*

Washable pre-filter traps dust and other

large airborne particles.

DECREASES ODOURS

Washable deodorizing ﬁ lter absorbs many

common household odours.

REDUCES POLLEN & MOLD*

HEPA filter traps 99.97% of particles as

small as 0.3 microns.

FRESHENS

Plasmacluster treats the air similar to the

way nature cleans the environment by

emitting a balance of positive and negative

ions.

HUMIDIFIES

Runs up to 10 hours per ﬁ lling.**

*When air is drawn through the filter sys-

tem.

**Room size:

up to 48 m

2

(KC-860E)

up to 38 m

2

(KC-850E)

up to 26 m

2

(KC-840E)

Sensor Technology continuously monitors

air quality, and automatically adjusting op-

eration based on detected air purity and

humidity.

E-2

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed, including the

following:

WARNING

– To reduce the risk of electrical shock, ﬁ re or injury to persons:

• Read all instructions before using the unit.

• Use only a 220~240 volt outlet.

• Do not use the unit if the power cord or plug is damaged or the connection to the wall outlet

is loosened.

• Periodically remove dust from the plug.

• Do not insert ﬁ ngers or foreign objects into the air intake or air outlet.

• When removing the power plug, always hold the plug and never pull on the cord.

Electrical shock and/or ﬁ re from a short circuit may result.

• Do not remove the plug when your hands are wet.

• Do not use this unit near gas appliances or ﬁ replaces.

• When reﬁ lling the Water Tank, cleaning the unit, or when the unit is not in use, be sure to unplug

the unit. Electrical shock and/or ﬁ re from a short circuit may result

• If the power cord is damaged, it must be replaced by the manufacturer, its service agent, a

Sharp authorized Service Centre or similarly qualiﬁ ed person in order to avoid a hazard.

• Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense,

sparks from lit cigarettes, chemical fumes in the air, or in locations where the unit may get wet,

such as a bathroom.

• Be cautious when cleaning the unit. Strong corrosive cleansers may damage the exterior.

• Only a Sharp Authorized Service Centre should service this air puriﬁ er. Contact the nearest Service

Centre for any problems, adjustments, or repairs.

• When carrying the unit, remove the Water Tank and Humidifying Tray ﬁ rst and hold the unit by han-

dles on both sides.

• Do not drink the water in the Humidifying Tray or Water Tank.

• Change the water in the Water Tank daily with fresh tap water and regularly clean the Water Tank

and Humidifying Tray. (See E-12 and E-13). When unit is not in use, dispose of the water in the

Water Tank and Humidifying Tray. Leaving water in the Water Tank and/or Humidifying Tray may

result in mold, bacteria, and bad odours.

In rare cases, this bacteria may cause harmful physical effects.

• This appliance is not intended for use by persons (including children) with reduced physical, sen-

sory or mental capabilities, or lack of experience and knowledge, unless they have been given su-

pervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure they do not play with the appliance.

NOTE

– Radio or TV Interference

If this air puriﬁ er should cause interference to radio or television reception, try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation distance between the unit and radio/TV receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced radio/TV technician for help.

E-3

ENG

CAUTIONS CONCERNING OPERATION

• Do not block the intake and/or air outlet.

• Do not use the unit near or on hot objects, such as stoves or heaters, or where it may come into

contact with steam.

• Always operate the unit in an upright position.

• Hold the unit by using the handles on both sides when moving.

Do not move when the unit is in operation.

• Do not operate the unit without the ﬁ lters, Water Tank, and Humidifying Tray properly in-

stalled.

• Do not wash and reuse the HEPA ﬁ lter.

Not only does it not improve ﬁ lter performance, it may cause electric shock or malfunction.

• Clean the exterior with a soft cloth only.

Do not use volatile ﬂ uids and/or detergents.

The unit surface may be damaged or cracked.

In addition, the sensors may malfunction as a result.

• Frequency of maintenance required (descaling) will depend on the hardness or the impuri-

ties of the water that you use; the harder the water the more often descaling will be neces-

sary.

• Keep the unit away from water.

INSTALLATION GUIDELINES

• When using the unit, place at least 2m away from equipment utilizing electric waves such

as televisions or radios to avoid electrical interference.

• Avoid a location where the sensor is exposed to direct wind.

The unit may not operate properly.

• Avoid use in locations where furniture, fabrics or other items may come in contact with and

restrict the air intake and/or air outlet.

• Avoid use in locations where the unit is exposed to condensation or drastic temperature

changes. Appropriate conditions are when room temperature is between 5 – 35 ºC.

• Place on a stable surface with sufﬁ cient air circulation.

When placing the unit on a heavily carpeted area, the unit may vibrate slightly.

Place the unit on an even surface to avoid water leakage from the Water Tank and/or Humidifying

Tray.

• Avoid locations where grease or oily smoke is generated.

The unit surface may crack or the sensor may malfunction as a result.

• Place the unit about 30 cm~60 cm(1~2 ft) away from the wall in order to ensure proper air-

ﬂ ow.

The wall directly behind the air outlet may become dirty over time. When using the unit for an ex-

tended period of time in the same location, periodically clean the wall and protect the wall with a

vinyl sheet, etc. to prevent the wall from becoming dirty.

FILTER GUIDELINES

• Follow the instructions in this manual for correct care and maintenance of the ﬁ lters.

E-4

Front Monitor

PART NAMES

ILLUSTRATIVE DIAGRAM – FRONT

Air Outlet

Main Unit

BACK

Handle (2 locations left and right)

Sensors

• Dust Sensor

•

Temperature / Humidity Sensor

•

Odour Sensor(KC860E

•

KC850E)

Tank Handle

Water Tank

(For humidifying)

Humidifying Filter

Tank Cap

Float

Humidifying Tray

Power Cord

Plug

Air Outlet

HEPA Filter (white)

Washable Deodorizing

Filter (black)

Tabs

Back Panel (Pre-Filter)

Air Inlet

Date Label

(Rating Label)

Filter Frame

KC-860E

KC-850E

Main Unit Display

Front Monitor

Main Unit

(Shape of plug depends on country.)

KC-840E

Air Outlet

E-5

ENG

Water Supply Indicator Light (red)

This light will illuminate when the water

tank needs to be reﬁ lled.

Sensor Reading

Sen

so

Senso

r Reading

or

r Reading

or

r

Reading

or

Flashing

Clean

All green

Green

Yellow

Very lmpure

All red

Clean

All green

Green

Yellow

Very lmpure

All red

Flashing

FRONT MONITOR

Indicates condition and humidity of room air.

Plasmacluster Indicator Light (blue)

Blue: Plasmacluster ON

Light off: Plasmacluster OFF

Humidity Indicator Light (green)

Displays the approximate humidity level

in the room. Humidity setting cannot be

adjusted.

KC-850E KC-860E

KC-840E

ODOUR MONITOR

The odour sensor continuously

monitors the air and changes colour

depending on odour intensity.

DUST MONITOR

The dust sensor continuously monitors

the air and changes colour depending on

air purity. KC-860E has 5 levels of dust

detector.

When the dust sensor detects dust,

the ﬂ ashing light moves depending on

dustiness.

Odour in the room

Faint

Strong

Green Yellow

Red

depending on odour

F

G

nding on odo

ur

Odou

r

Fa

in

t

G

ree

n

r

intensity

.

e

room

S

tron

g

w

R

ed

odo

ur

r

in th

e

Y

e

ll

ow

Dust and odor are detected by different

sensors.The colours may not change

simultaneously.

(Ex.) At 60 % humidily

80 % or more

Less than 30 %

DUST MONITOR

The dust sensor continuously

monitors the air and changes colour

depending on air purity.

Sensor Reading

Clean

All green

Green

Yellow

Very lmpure

All red

Clean

All green

Green

Yellow

Very lmpure

All red

C

l

e

All g

C

l

e

gpy

Sen

so

Sen

so

Sen

so

e

a

n

G

reen

Ye

reen

Ye

ree

n

Ye

e

G

reen

Ye

e

a

n

G

e

d

low

A

ll r

e

l

G

l

een

e

re

y

r Reading

or

r Reading

or

o

G

e

G

e

G

m

pur

e

r

Reading

e

n

V

er

y

l

m

or

e

or

r

e

ed

e

low

All re

l

ell

e

d

m

pur

e

m

low

All re

l

ell

l

ell

e

en

e

re

e

re

low

All

re

V

er

y

l

m

l

ell

Flashing

Humidity Indicator Light (green)

Displays the approximate humidity level

in the room. Humidity setting cannot be

adjusted.

High – 65 % or more

Med – 65 % or less of 40 % or more

Low – 40 % or less

Water Supply Indicator Light(red)

This light will illuminate when the water

tank needs to be reﬁ lled.

When the dust sensor detects dust,

the ﬂ ashing light moves depending on

dustiness.

Plasmacluster Indicator Light (blue)

Blue: Plasmacluster ON

Light off: Plasmacluster OFF

Indicates the room condition of odour, dust, and humidity.

E-6

Date Label

Unplug the unit before installing

or adjusting the ﬁ lters.

PREPARATION FOR

USE

1

Remove the Back Panel.

Gently push down on the tabs,

then tilt and remove the back

panel.

Install the ﬁ lters

1

Install the HEPA Filter.

Please make sure that the HEPA Filter is

placed in proper orientation.

To maintain the quality of the ﬁ lters, they are packed in plastic bags and placed in the

unit. Be sure to remove the ﬁ lters from the plastic bags and replace the ﬁ lters in the

unit before initial use.

Remove the ﬁ lters

Back Panel

HEPA Filter

Washable

Deodorizing

Filter

HEPA Filter

FILTER INSTALLATION

1

2

Tabs on the top

Washable Deodorizing Filter

Back Panel

Bottom tabs

Upper tabs

Installing the filter backwards

will affect the performance of

the unit.

Tab

2

Remove the Wash-

able Deodorizing Filter

(black) and HEPA Filter

(white) from the plastic

bags.

2

Insert the Back Panel’s 2 bottom tabs

(left and right) into the small holes in the

unit, and slide the Washable Deodor-

izing Filter between the HEPA Filter and

the Back Panel.

3

Gently push in the up-

per tabs (left and right)

to lock in place.

4

Fill in the usage start

date on the Date Label.

Use the usage start date as

a guide for when the ﬁ lters

should be replaced.

E-7

ENG

REFILLING THE WATER TANK

CAUTION

Tank Handle

Water Tank

Tank Cap

Water Tank

Humidifying

Tray

tighten

• Do not expose the unit to water. Short circuit and/or electrical shock may occur as a result.

• Do not use hot water (40 ºC), chemical agents, aromatic substances, dirty water, or other

damaging substances, deformation and/or malfunction may occur.

• Use only fresh tap water. Use of other water sources may promote the growth of mold, fun-

gus and/or bacteria.

The unit can be used in the Clean Air Mode without

putting water in the Water Tank. When using the Clean

Air & Humidify Mode, or the CLEAN ION SHOWER

Mode, the Water Tank should be ﬁ lled with water.

1

Remove the Water Tank by unlatching the

top.

2

Remove the Water Tank Cap and carefully

ﬁ ll the Water Tank with tap water.

• Change the water in the Water Tank every day with

fresh tap water.

3

After ﬁ lling, securely tighten the Tank Cap.

• Check to see that there is no water leaking.

• Be sure to wipe off any excess water on the outside of

the Water Tank.

• When carrying the Water Tank, hold it with both hands

so that the Water Tank opening is facing up.

4

Replace the Water Tank in the unit.

• The top latch will “click” in place when the Water Tank

is properly installed.

E-8

CLEAN AIR & HUMIDIFY MODE

OPERATION

Use the Clean Air & Humidify Mode to quickly clean the air, reduce odours and to humidify.

About Automatic Humidify Mode

The Temperature/Humidity sensors automatically detect and

adjust humidity according to changes in room temperature.

Depending on the size and humidity of the room, humidity

may not reach 55~65 %. In such cases, it is recommended

that CLEAN AIR & HUMIDIFY/MAX MODE be used.

Power OFF Button

Power ON Button

Light Control

Button

Fan Speed Button/

Indicator Light (green)

CLEAN ION SHOWER MODE Button/

Indicator Light (blue)

Press any of the buttons to se-

lect mode and start the unit.

Clean Air & Humidify MODE Button/

Indicator Light (green)

Clean Air MODE Button/

Indicator Light (green)

MAIN UNIT DISPLAY

Press the Power OFF Button to turn the unit off.

Filter Reset Button/

Indicator Light (red)

Plasmacluster ON/OFF Button/

Indicator Light (green)

1

Fill Water Tank. (See E-7)

2

Press the CLEAN AIR & HUMIDIFY MODE Button.

• If the power cord was not unplugged between uses, the unit

will automatically re-start at the previously selected settings.

3

Press the FAN SPEED Button to select the de-

sired fan speed.

• Indicator lights will show the fan speed

currently selected.

Temperature Humidity

~18 ºC 65 %

18 ºC~24 ºC 60 %

24 ºC~ 55 %

E-9

ENG

Use the Clean Air Mode when additional humidity is not required.

CLEAN AIR MODE

CLEAN ION SHOWER Mode with humidiﬁ cation releases high-density Plasmacluster ions.

By continuously discharging strong airﬂ ow for 15 minitues, the unit effectively removes air-

borne dust, pollen, mold and allergens from the air as they are drawn through the ﬁ lter system.

Water must be in the Water Tank when this mode is selected.

The unit humidiﬁ es when there’s water in the Water Tank, and it operates without humidifying

when there’s no water in it.

Press the Power OFF Button to turn the unit off.

Fan Speed Button

Please note the fan speed cannot be adjusted during the CLEAN ION SHOWER MODE.

AUTO operation

The fan speed is automatically switched (between HIGH and LOW) depend-

ing on the amount of impurities in the air. The sensors detect impurities for

efﬁ cient air purﬁ cation.

POLLEN mode

The unit will operate at High Level for

10 minutes, then will atternate be-

tween MEDIUM and HIGH.

10 minutes: High fan level

20 minutes: Medium fan level

20 minutes: High fan level

MAX operation

The unit will operate at maximum fan speed.

MEDIUM operation

The unit will operate at medium fan speed.

LOW operation

The unit will operate quietly using minimal air intake.

CLEAN ION SHOWER MODE

1

Press the CLEAN AIR MODE Button on the display.

• If the power cord was not unplugged between uses, the unit will

automatically re-start at the previously selected settings.

2

Press the FAN SPEED BUTTON to select the de-

sired fan speed.

• Indicator lights will show the fan

speed currently selected.

1

Press the CLEAN ION SHOWER MODE Button

on the display to select this mode.

When the operation ﬁ nishes, the unit will return to the prior

operation.

operation

*HiGH fan speed is an intermediate speed between MEDIUM and MAX.

E-10

OPERATION

WATER SUPPLY INDICATOR LIGHT

When the Water Tank is empty, the Water Supply Indicator Light will ﬂ ash

to indicate that the Water Tank should be reﬁ lled. Please note the light

will not ﬂ ash even when the Water Tank is empty during the Clean

Air Mode and the Clean ION SHOWER Mode.

Sound indicator setting for water supply.

In addition to the Indicator Light, the unit can be set to signal with an audible beep when the

Water Tank is empty. With the unit OFF, press the Lights Control button for 3 seconds to turn

the audible signal ON.

Cancellation

To cancel the audible signal, with the unit OFF, press the Lights

Control button again more than 3 seconds.

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY

Set to “low” if the DUST MONITOR and ODOUR MONITOR is constantly red to reduce

sensitivity, and set to “high’ if the DUST MONITOR and ODOUR MONITOR is constantly

green to increase sensitivity.

Sensor

Detection

sensitivity

Fan Speed

Indicator

Light

LIGHTS CONTROL Button

Use when the light on the

front panel is too bright.

High

Standard

Low

Plasmacluster ON/OFF Button

Press the Plasmacluster ON/OFF Button to turn Plasmaclus-

ter Ion Mode ON and OFF.

When Plasmacluster is ON, both the Indicator Light and

Plasmacluster Indicator Light turn on.

Refer to the diagram on the right to select the

desired brightness on the front panel.

The lights on the front panel are brighter.

The lights on the front panel are darker.

The lights on the front monitor turn off

CAUTION

The lights on the front monitor are always brighter when starting.

The lights on the front panel are brighter.

The lights on the front panel are darker.

The lights on the front monitor turn off.

1

With the unit OFF, press the Fan Speed Button for 3 seconds.

The Fan Speed Indicator Lights will display the currently set sensor sensitivity level. The

factory setting is Standard, indicated by the MED light.

2

Press the Fan Speed Button to set the desired sensor sensitivity.

Refer to the diagram on the right to select the desired sensor sen-

sitivity level.

3

Press the Power OFF Button.

Note that if the Power OFF Button is not pushed within 8 seconds

of adjusting sensor sensitivity, the setting will be saved automati-

cally. The sensor sensitivity setting will be saved even if the unit is

unplugged.

Flashing

E-11

ENG

CARE AND MAINTENANCE

UNIT

FILTER INDICATOR LIGHT

The Filter Indicator Light will illuminate as a reminder to perform maintenance

of the Back Panel, Sensors, and Humidifying Filter. The Indicator Light will turn

on after approximately 720 hours of use.

After performing maintenance, reset the Filter Indicator. Plug the unit in, turn

power ON, and press the RESET button for 3 seconds. The Filter Indicator

Light will go off. Even if the Filter Indicator Light is already off, the RESET but-

ton should be pressed to reset the maintenance timer.

BACK PANEL and SENSORS

Sensor

Back Panel

Sensor Filter

To maintain optimum performance of this air puriﬁ er, please clean the unit including

the sensor and ﬁ lters periodically.

When cleaning the unit, be sure to ﬁ rst unplug the power cord, and never handle the

plug with wet hands. Electrical shock and/or bodily injury may occur as a result.

Back Panel

Care Cycle

After 720 hours of use

(

30days × 24hours = 720)

Care Cycle

Whenever dust accumulates

on the unit or every 2 months

Gently remove dust from the sensor opening and the

back panel, using a vacuum cleaner attachment or

similar tool.

When the back panel has stubborn dirt

1

In case of oily dirt, soak the back panel in water with

kitchen detergent.

Avoid scrubbing the back panel hard when washing.

2

Rinse the back panel repeatedly with clean water to re-

move the solution residue.

3

Drip dry ﬁ lter to remove excess water.

SENSOR FILTER CARE

Remove the sensor filter and tap it lightly over a sink

or bin to dislodge dust. If it is very dirty, wash it gently

with lukewarm water. Do not use any detergents or

chemicals of any kind to clean the ﬁ lter. Dry the ﬁ lter

completely before replacing in the unit. Do not operate

unit without all ﬁ lters properly installed.

Care Cycle

Whenever dust accumulates on the unit or every 2 months

To prevent dirt or stains on the unit, clean regularly. If stains are allowed to remain, they may

become difﬁ cult to remove.

Wipe with a dry, soft cloth

For stubborn stains or dirt, use a soft cloth dampened with warm water.

Do not use volatile ﬂ uids

Benzene, paint thinner, polishing powder, may damage the surface.

Do not use detergents

Detergent ingredients may damage the unit.

E-12

CARE AND MAINTENANCE

WATER TANK

HAND WASH ONLY!

DO NOT DRY IN CLOTHES

DRYER!

Rinse the inside of the tank by leaving a small amount of luke-

warm water inside, closing the tank cap firmly, and shaking

the tank. Mild household detergents may be used to clean the

inside of the tank, but detergent should be diluted and the tank

should be thoroughly rinsed to remove all detergent residue.

(Note the Water Tank is not dishwasher safe.)

TANK CAP CARE

care cycle... once a month

The small cap back of the tank cap is removable.

When the tank cap and small cap are dirty and slimy,

cleaning is necessary.

Use a cotton swab or a toothbrush.

Tank Cap

Water Tank

WASHABLE DEODORIZING FILTER CARE

Tank Cap

Toothbrush

Care Cycle

Every day when Humidifying

Care Cycle

When an unpleasant odour is noticed

from the air outlet.

When performance of ﬁ lter seems to be

reduced and odours persist.

2

Drip dry ﬁ lter to remove excess water.

1

Rinse dirt from the WASHABLE DEODORIZING

FILTER under lukewarm water.

Remove dust on the washable deodorizing ﬁ lter before washing.

CAUTION

• When washing the ﬁ lter for the ﬁ rst time, the rinse water may

be brown. This does not affect deodorization performance.

• Avoid bending or folding the ﬁ lter when washing.

3

Dry filter completely in a well ventilated area. If

possible, dry outdoors.

Dry ﬁ lter in a sideways position to avoid warping of the ﬁ lter.

The ﬁ lter takes about 6 hours to dry out.

CAUTION

• Avoid drying ﬁ lter outdoors during inclement weather (e.g. rain or cold

temperatures).

Do not allow ﬁ lter to freeze.

• If ﬁ lter is dried indoors, take precautions, such as placing towels, etc

under the ﬁ lter to prevent water damage to the ﬂ oor.

4

Replace the ﬁ lter in unit. (See E-6).

Dry ﬁ lter completely before replacing to prevent odours.

Do not operate unit without all ﬁ lters properly installed.

E-13

ENG

Frequency of maintenance cycle will depend on the hardness

of the water. Avoid spilling water when removing or cleaning

the tray.

1

Remove the Water Tank and Humidifying

Tray.

Unlatch the Water

Tank first, then re-

move the tray. Use

both hands when

pulling out the Hu-

midifying Tray to

avoid spilling water.

3

Rinse the inside of the Humidifying

Tray with lukewarm water to remove

impurities.

• Do not remove the

Styrofoam ﬂ oat.

• Clean difﬁ cult-to-

reach parts with a

cotton-tipped swab

or tooth brush.

CAUTION

Humidifying Filter

Water Tank

Tank Handle

Humidifying

Tray

Float

If the Styrofoam ﬂ oat comes off,

replace by inserting the tabs of

the Float into the holes in the

Humidifying Tray as shown in the

diagram.

When Water Deposits are Difﬁ cult to Remove

• Use only mild kitchen detergents to

clean the Humidifying Tray. Use of

non-designated chemicals or deter-

gents can cause deformation, tar-

nishing, cracking (water leakage).

Insert the ﬂ oat below

this tab.

Insert the tab on

the other side of the

ﬂ oat into the hole.

Insert the tab of the

ﬂ oat into the hole.

1

Fill Humidifying Tray half-

way with lukewarm water,

add a small amount of mild

kitchen detergent, and leave

to soak for about 30 min-

utes.

Dilute detergent according to

instructions on the container.

Clean difﬁ cult-to-reach parts

with a cotton

swab or tooth

brush.

2

Rinse the Humidifying

Tray with lukewarm wa-

ter.

• Rinse until all detergent residue

is removed.

• Inadequate rinsing may

cause the de-

tergent odour

or changes

in the shape/

colour of the

main unit.

4

Replace the Humidifying Filter and re-

place the Humidifying Tray in the unit.

The Humidifying Filter will not

ﬁ t if placed in backwards. Be

sure there is no gap between

the Humidifying tray and the

unit when the Humidifying Tray

is replaced in the unit. The unit

may not operate properly if the

Humidifying Tray is not prop-

erly replaced in the unit.

Do not hold

this part.

2

Remove the Humidifying Filter from the

Humidifying Tray. Drain accumulated wa-

ter by tilting the Humidifying Tray slowly.

Colour: Gray

HUMIDIFYING TRAY

Care Cycle

1 month

E-14

CARE AND MAINTENANCECARE AND MAINTENANCE

Frequency of maintenance cycle will depend on the hardness or the impuri

ties of the water that

you use; the harder the water the more often descaling will be necessary.

Pay attention not to spill water when cleaning the ﬁ lter.

1

Remove the Water Tank and

Humidifying Tray.

2

Remove the Humidifying Filter

from the Humidifying Tray.

Avoid spilling water from the Humidifying

Tray.

3

Preparing the descaling solu-

tion.

Citric acid, available at some drugstores,

or 100 % bottled lemon juice are used for

descaling. Choose either one to use, and

prepare the descaling solution.

Dissolve 3 teaspoons of citric acid and 2

1/2 cups of lukewarm water in a suitable

container, and stir well.

100 % bottled lemon juice can be used

for descaling. Use only 100 % bottled

lemon juice with no pulp (strain juice if

necessary). Combine 1/4 cup lemon juice

and 3 cups of lukewarm water in a con-

tainer large enough to hold the Humidify-

ing Filter and stir well.

4

When using lemon juice,

it is recommended to pre-

soak longer than citric

acid.

5

Rinse the Humidifying Filter re-

peatedly with lukewarm water

to remove all the solution resi-

due.

Inadequate rinsing may cause odour and

affect the performance and/or appear-

ance of the unit.

* Do not scrub the Humidi-

fying Filter, rinse gently

under lukewarm water

only.

6

Attach the Humidifying Filter

to the Humidifying Tray, and

replace the Humidifying Tray in

the unit.

•The Humidifying Filter will not fit if

placed in backwards. Be sure there is

no gap between the Humidifying Tray

and the unit when the Humidifying Tray

is replaced in the unit. The unit may not

operate properly if the Humidifying Tray

is not properly replaced in the unit.

•When not using the

unit for a long peri-

ods of time, dry the

Humidifying Filter

completely before

replacing.

7

Plug in the unit, turn power

ON, and press the Filter Reset

Button on the display for more

than 3 seconds to reset.

You may notice reddish-brown or white

deposits forming on the surface of the

Humidifying Filter. These impurities (cal-

cium, etc.) are due to the impurities con-

tained in tap water; this is not a defect.

Replace the Humidifying Filter when it is

covered completely

in white deposits.

Water Tank

Humidifying

Tray

Humidifying ﬁ lter

Humidifying

Tray

HUMIDIFYING FILTER

Care Cycle

Once a month or when the Filter Indicator Light is on.

P

re-soak the Humidifying Filter

in the solution for 30 minutes

before cleaning.

E-15

ENG

Humidifying ﬁ lter

(Gray)

Filter Frame (Gray)

(white)

Filter Frame (white)

FILTER REPLACEMENT GUIDELINES

Filter life will vary depending on the room environment, usage, and location of the unit. If dust

or odours persist, replace the ﬁ lters.

(Refer to “Please read before operating your new Air Puriﬁ er”)

Guide for ﬁ lter replacement timing

HEPA Filter

Up to 5 years after opening

Filter life can be greatly reduced depending on the room environment. Cigarette smoke, pet dander,

and other airborne particles can reduce ﬁ lter life. Check ﬁ lters regularly and replace as necessary.

Washable Deodorizing Filter

The ﬁ lter can be repeatedly used after washing, or it can be replaced.

Humidifying Filter

Up to 2 years after opening

Filter life can be greatly reduced depending on the room environment. Even if 2 years have not

passed, replace the Humidifying Filter if you notice the following:

• Mineral deposits (white, black, or red masses) which are not removed after cleaning or the Humidi-

fying Filter is still dirty.

• Filter is severely damaged or warped.

Replacement Filters

• HEPA Filter: 1unit

Model FZ-C150HFE (for KC-860E)

FZ-C100HFE (for KC-850E)

FZ-C70HFE (for KC-840E)

• Washable Deodorizing Filter: 1unit

Model FZ-C150DFE (for KC-860E)

FZ-C100DFE (for KC-850E)

FZ-C70DFE (for KC-840E)

• Humidifying Filter: 1unit

Model FZ-C100MFE

Replacing the Filters

1. Replace ﬁ lters according to the instructions provided with the replacement ﬁ lters.

2. Use the date labels as a reminder for when the ﬁ lters should be replaced.

Disposal of Filters

Please dispose of used ﬁ lters according to any local laws and regulations.

HEPA Filter materials:

• Filter: Polypropylene • Frame: Polyester

Washable Deodorizing Filter materials:

• Polyester, Rayon, Activated charcoal

Humidifying Filter materials:

• Rayon, Polyester

E-16

TROUBLESHOOTING

Before calling for service, please review the Troubleshooting chart below, since the problem may not

be a unit malfunction.

SYMPTOM REMEDY (not a malfunction)

Odours and smoke are not

removed.

• Clean or replace the ﬁ lters if they appear to be heavily soiled.

(See E-11,E-12,E-14)

The Front Monitor illuminates

green even when the air is

impure.

• The air could be impure at the time the unit was plugged in.

Unplug the unit, wait one minute, and plug the unit in again.

The Front Monitor illuminates

orange or red even when the

air is clean.

• Sensor operation is affected if the dust sensor openings are

dirty or clogged. Gently clean the dust sensors (See E-11).

A clicking or ticking sound is

heard from the unit.

• Clicking or ticking sounds may be audible when the unit is

generating ions.

The discharged air has an

odour.

• Check to see if the ﬁ lters are heavily soiled.

• Clean or replace the ﬁ lters.

• Plasmacluster Air Puriﬁ ers emit small traces of ozone which

may produce an odour.

The unit does not operate

when cigarette smoke is in the

air.

• Is the unit installed in a location that is difﬁ cult for the sensor

to detect cigarette smoke?

• Are the dust sensor openings blocked or clogged?

(In this case, clean the openings.) (See E-11)

Filter Indicator Light is

illuminated.

• After replacing ﬁ lters, connect the power cord to an outlet and

press the Filter Reset Button. (See E-11)

The Front Monitor are turned

off.

• Check to see if the Lights OFF Mode selected. If so, then

press the Lights Control Button to activate the indicator lights.

(See E-10)

The Water Supply Indicator

Light does not illuminate when

the tank is empty.

• Check Styrofoam ﬂ oat for impurities. Clean the Humidifying-

Tray. Ensure unit is located on a level surface.

Water lever in the tank does

not decrease or decreases

slowly.

• Check to see if the Humidifying Tray and Water Tank are cor-

rectly installed. Check the Humidifying Filter.

• Clean or replace the filter when it is heavily soiled

(See E-14 and E-15).

The Front Monitor lights

change colour frequently.

• The Front Monitor lights automatically change colours as im-

purities are detected by the dust sensor and odour sensor.

E-17

ENG

ERROR DISPLAY

KC-850E•KC-860E

If error occurs again, contact the Sharp Service Centre.

DIGITAL

INDICATION

LAMP INDICATION ERROR DETAILS REMEDY

Flashing of the Clean Air &

Humidify Indicator Light.

Abnormal humidity ﬁ lter Verify if the Humidifying Filter,

Humidifying Tray and Water

Tank are properly installed and

then turn power ON again.

Flashing of the Fan Speed

Indicator Light '

'.

Abnormal fan motor

Turn power OFF to cancel the

error display, wait one minute,

and then turn power ON.

Abnormal temperature-

humidity sensor

Unplug the unit, wait one

minute, and plug the unit in

again.

Flashing of the Clean Ion

Shower Indicator Light.

Problem in circuit board

Flashing of the Clean Air Indi-

cator Light.

Flashing of the Fan Speed In-

dicator Light ' '.

Flashing of the Fan Speed In-

dicator Light ' '.

KC-840E

LAMP INDICATION ERROR DETAILS REMEDY

Flashing of the Clean Air &

Humidify Indicator Light.

Abnormal humidity ﬁ lter Verify if the Humidifying Filter,

Humidifying Tray and Water

Tank are properly installed and

then turn power ON again.

Flashing of the Fan Speed

Indicator Light '

'.

Abnormal fan motor

Turn power OFF to cancel the

error display, wait one minute,

and then turn power ON.

Abnormal temperature-

humidity sensor

Unplug the unit, wait one

minute, and plug the unit in

again.

Flashing of the Clean Ion

Shower Indicator Light.

Problem in circuit board

Flashing of the Clean Air Indi-

cator Light.

Flashing of the Fan Speed In-

dicator Light '

'.

Flashing of the Fan Speed In-

dicator Light '

'.

Flashing of the Humidity Indi-

cator Light ‘High’ or ‘Low’.

E-18

SPECIFICATIONS

Model KC-860E KC-850E KC-840E

Power supply 220 ~ 240 V 50/60 Hz

Fan Speed Adjustment MAX MED LOW MAX MED LOW MAX MED LOW

CLEAN AIR

Fan Speed (m

3

/hour)

396 240 84 306 168 60 210 132 48

Rated Power (W)

56 19 5.5 (4.9) 41 11.6 3.8 (3.3) 26 9.5 3.7 (3.4)

Noise Level (dBA)

51 39 17 47 35 15 45 34 15

CLEAN AIR

& HUMIDIFY

Fan Speed (m

3

/hour)

396 240 120 288 168 84 186 132 54

Rated Power (W)

56 21 8.8 (8.2) 40 13.5 6.8 (6.3) 21 11.5 6.1 (5.8)

Noise Level (dBA)

50 39 25 47 35 22 42 34 20

Humidiﬁ cation (mL/hour)*2

730 500 300 600 400 230 450 330 170

Recommended Room Size (m

2

)*1 ~48 ~38 ~26

Water Tank Capacity (L) 4.3 4.0 3.0

Sensors

Dust/odour/Temperature & Humidity Dust/Temperature & Humidity

Filter type

Dust collection HEPA with Microbial control *3

Deodorization Washable Deodorizing

Cord Lenght (m) 2.0

Dimensions (mm) 398 (W) × 288 (D) × 627 (H) 378 (W) × 265 (D) × 586 (H) 360 (W) × 233 (D) × 550 (H)

Weight (kg) 11.0 9.0 8.0

*1 • The Recommended Room Size is appropriate for operating the unit of maximum fan speed.

• The Recommended Room Size area indicates the space where a certain amount of dust particles can be removed in 30 minutes.

*2 • Humidiﬁ cation Amount changes in accordance with indoor and outdoor temperature and humidity.

Humidiﬁ cation Amount increases as temperatures rise or humidity decreases.

Humidiﬁ cation Amount decreases as temperatures decrease or humidity rises.

• Measurement Condition: 20 ºC, 30 % humidity (JEM1426)

*3 •

The class of the HEPA ﬁ lter by EN1822 is H10.

Standby Power

In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this

product consumes about 0.7 W of standby power.

For energy conservation, unplug the power cord when the unit is not in use.

La page est en cours de chargement...

Sharp KC-850E Le manuel du propriétaire

Ce manuel convient également à

Sharp KC-850E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents