E
PE
DB98-25309A(1)
Split-type Room Air Conditioner
(Cooling and Heating)
USER'S MANUAL
AS18HM Series
AS24HM Series
AS18HM_E_25309A(1).indd 29 2006-02-15 ¿ÀÈÄ 1:41:59
E-2
Safety Precautions
You should take the following safety precautions when using your air conditioner.
Do not repair the air conditioner at your discretion.
It is recommended to contact a service center directly.
Never spill any kind of liquid on the air conditioner.
If this happens, turn off the air conditioner and contact an authorized service
center.
Do not insert anything between the airflow blades to prevent damage of the
inner fan and consequent injury. Keep children away from the air conditioner.
Do not place any obstacles in front of the air conditioner.
Do not spray any kind of liquid into the indoor unit. If this happens,
turn off the air conditioner and contact a service center.
Make sure that the air conditioner is well ventilated at all times:
Do not place a cloth or other materials over it.
Remove the batteries if you don’t use the remote control for a long time.
(If applicable)
Use the remote control within 7 m from the indoor unit. (If applicable)
DURING OPERATION
Never store or load the air conditioner upside down or sideways to
prevent the damage to the compressor.
Young children or infirm persons should be always supervised when they use
the air conditioner.
Max current is measured according to IEC standard for safety.
Current is measured according to ISO standard for energy efficiency.
OTHERS
Before throwing out the air conditioner, remove the batteries from the remote
control.
When you dispose of the air conditioner, consult your dealer. If pipes are
removed incorrectly, refrigerant may blow out and cause air
pollution. When it contacts with your skin, it can cause skin injury.
The package of the air conditioner should be recycled or disposed of properly
for environmental reasons.
DISPOSING OF THE UNIT
Register your product at www.samsung.com/global/register
WARNING
•
If you don’t follow the safety precautions, you may get the risk of an electric
shock, injury or death.
•
The manufacturer or qualified service personnel must
install this air conditioner.
•
Turn off the electric power before repairing, installing
or cleaning.
AS18HM_E_25309A(1).indd 2 2006-02-15 ¿ÀÈÄ 1:40:49
E-3
Contents
PREPARATION
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Name of Each Part. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Control - Buttons and Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Getting Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION
Selecting the Auto Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Selecting the Cool Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selecting the Heat Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting the Dry Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Selecting the Fan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Selecting the Turbo Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selecting the Energy Saving Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting the Auto Cleaning Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Selecting the Sound On/ Off Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Selecting the Anions Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adjusting the Airflow Direction Vertically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Adjusting the Airflow Direction Horizontally. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
RECOMMENDATIONS FOR USE
Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Operating Your Air Conditioner Without the Remote Control . . . . . . . . . 25
Troubleshooting Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning Your Air Conditioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning Anti-Allergy and Deodorizing Filter (Option). . . . . . . . . . . . . . . . . 27
TECHNICAL SPECIFICATIONS
AS18HM_E_25309A(1).indd 3 2006-02-15 ¿ÀÈÄ 1:40:49
E-4
Name of Each Part
The design and shape can be changed according to the model.
Air filter
(under the grille)
Airflow blades
(outlet)
Power(On/Off) button
Auto cleaning indicator
(Green)
Energy saving indicator
(Green)
Anions indicator
(Green)
Set temperature &
room temperature
Operation indicator
(Auto-Cool, Cool, Dry, Fan : Green
Auto-Heat, Heat : Orange)
Turbo function indicator
(Green)
Timer indicator
(Orange)
Fan speed indicator
(Green)
Remote control sensor
Room temperature sensor
In the Auto mode, 2 fan indicators increase and decrease continuously and
turn round.
In the modes except the Auto mode, the fan speed indicator increases and
decreases continuously and turn round each time you press the
button. If you set the Turbo function, the fan speed indicator turns round
with the maximum setting and speed.
If you want to turn on/off the Display during operation,
press the button on the remote control.
The room temperature sensor senses air temperature around the sensor,
and shows the temperature on the display.
Note
Indoor Unit
Air inlet
AS18HM_E_25309A(1).indd 4 2006-02-15 ¿ÀÈÄ 1:40:50
E-5
Name of Each Part
Outdoor Unit
AS18HM Series
Air Inlet(Rear)
Air Outlet
Connection Valve
Air Inlet(Rear)
Air Outlet
Connection Valve
Outdoor Unit
AS24HM Series
AS18HM_E_25309A(1).indd 5 2006-02-15 ¿ÀÈÄ 1:40:52
E-6
Remote Control - Buttons and Display
Remote control
transmission indicator
Swing button
Mode selection button
(AUTO, COOL, DRY, FAN, HEAT)
Fan speed adjustment button
Battery life indicator
Fan speed indicator
Anions indicator
Sleep mode indicator
Off Timer button
On Timer button
Power (On/Off) button
On Timer indicator
Air flow direction
Off Timer indicator
Timer Set/Cancel button
Sleep button
Anions button
Operating mode
( AUTO, COOL, DRY,
FAN, HEAT)
Sound On/Off indicator
Turbo function indicator
Temperature setting
Energy saving indicator
Temperature adjustment
buttons
Sound On/Off button
Auto Cleaning button
Turbo button
Energy saving button
Digital On/Off button
AS18HM_E_25309A(1).indd 6 2006-02-15 ¿ÀÈÄ 1:40:55
E-7
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when:
You purchase the air conditioner
The remote control does not work correctly
Note
Use 2 AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months,
even
if they have not actually been used.
1
Remove the battery cover in the rear of the remote control by pushing it with
your thumb.
2
Insert two batteries, respecting the polarities as indicated by the + and
- symbols.
3
Close the cover by sliding it back in its place.
AS18HM_E_25309A(1).indd 7 2006-02-15 ¿ÀÈÄ 1:40:57
E-8
Getting Started
The User’s Manual provides you with valuable information about your air conditioner.
Please read this manual carefully before using the air conditioner.
It will help you take full advantage of the unit's features.
You have already seen the basic description of the unit on pages from 4 to 6.
Starting with the next page, you will find a series of step-
by-step procedures
for each function available.
The illustrations in the step-by-step procedures use 3 different symbol
s:
PRESS PUSH HOLD DOWN
AS18HM_E_25309A(1).indd 8 2006-02-15 ¿ÀÈÄ 1:40:58
E-9
Selecting the Auto Mode
Control Panel
You can select the Auto mode if you want to cool or heat your room
automatically. You can adjust the temperature in this mode.
1
If necessary, press the (On/ Off ) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button on the remote control until is displayed.
Result: The indoor unit beeps each time you press the button.
The air conditioner runs in the Auto mode.
The Auto mode cools or heats the room depending on
the set temperature.
The air conditioner changes the Cool or Heat mode automatically
depending on the current temperature during operation.
Note
You can change modes at any time.
3
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 16°C and 30°C.
Result:
Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
The fan speed is adjusted automatically.
2 fan speed indicators increase and decrease continuously and
turn round.
AS18HM_E_25309A(1).indd 9 2006-02-15 ¿ÀÈÄ 1:41:00
E-10
Selecting the Cool Mode
Control Panel
You can select the Cool mode if you want to cool your room.
You can adjust the temperature and the fan speed when cooling.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button on the remote control until is displayed.
Result: The indoor unit beeps each time you press the button.
The air conditioner runs in the Cool mode.
Note
You can change modes at any time.
3
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 16°C and 30°C.
Result:
Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
If the room temperature is higher than the selected
temperature, the air conditioner starts cooling.
If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan operates consistently.
4
Press the
button to select the fan speed until the required setting is
displayed.
Automatic (rotated : )
Low
Medium
High
Result: Each time you press the
button, the indoor unit beeps.
The fan speed indicator increases and decreases
continuously and turns round each time you press
the
button.
Note
The fan speed indicator of the indoor unit varies according
to the temperature in the Automatic fan speed.
5
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 10 2006-02-15 ¿ÀÈÄ 1:41:04
E-11
Selecting the Heat Mode
Control Panel
You can select the Heat mode if you want to heat your room.
You can adjust the temperature and the fan speed when heating.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button on the remote control until is displayed.
Result: The indoor unit beeps each time you press the button.
The air conditioner runs in the Heat mode.
Note
You can change modes at any time.
3
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 16°C and 30°C.
Result:
Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
If the room temperature reaches 5°C higher than the set temperature,
the air conditioner stops heating, but the fan operates consistently.
If the room temperature reaches 3°C lower than the set
temperature, the air conditioner starts heating again.
4
Press the
button to select the fan speed until the required setting is
displayed.
Automatic (rotated : )
Low
Medium
High
Result: Each time you press the
button, the indoor unit beeps.
The fan speed indicator increases and decreases
continuously and turns round each time you press
the
button.
For the first 3~5 minutes, the fan may not operate to prevent
cool air from flowing out of the indoor unit.
It helps to warm the air in your room sufficiently.
Note
The fan speed indicator of the indoor unit varies according
to the temperature in the Automatic fan speed.
5
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 11 2006-02-15 ¿ÀÈÄ 1:41:08
E-12
Selecting the Dry Mode
You can select the Dry mode if you want to dehumidify your room.
You can adjust the temperature in this mode.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button on the remote control until is displayed.
Result: The indoor unit beeps each time you press the button.
The air conditioner runs in the Dry mode.
Note
You can change modes at any time.
3
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 18°C and 30°C.
Result:
Each time you press the
button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
The air conditioner starts dehumidifying and the fan speed is
adjusted automatically.
4
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 12 2006-02-15 ¿ÀÈÄ 1:41:11
E-13
Selecting the Fan Mode
Control Panel
You can select the Fan mode if you want to ventilate your room. It helps to refresh the air
in your room. You can adjust the fan speed in this mode.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button on the remote control until is displayed.
Result: The indoor unit beeps each time you press the button.
The air conditioner runs in the Fan mode.
The temperature is set automatically.
Note
You can change modes at any time.
4
Press the
button to select the fan speed until the required setting is
displayed.
Low
Medium
High
Result: Each time you press the
button, the indoor unit beeps.
The fan speed indicator increases and decreases
continuously and turns round each time you press
the
button.
4
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 13 2006-02-15 ¿ÀÈÄ 1:41:14
E-14
Selecting the Turbo Function
Control Panel
You can select the Turbo Function if you want to cool or heat your room in the
fastest way. After the 30-minute operation with the maximum setting,
it returns to the previous setting.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button.
Result: The temperature and fan settings are adjusted automatically.
The fan speed indicator turns round with the maximum
setting and speed.
The air conditioner cools or heats the room as quickly as possible.
After 30 minutes, the air conditioner is reset automatically to the
previous setting.
You can select the Turbo function in the Auto, Cool and Heat mode.
If you select this function in the Dry or Fan mode, the mode
changes to the Auto mode.
3
Press the
button again to stop the Turbo Function before the end of the
30-minute period.
Result: The air conditioner is reset automatically to the previous setting.
4
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 14 2006-02-15 ¿ÀÈÄ 1:41:18
E-15
Selecting the Energy Saving Function
You can select the Energy Saving Function to save energy when
cooling. The temperature range decreases in order to perform this function.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button.
Result: The indoor unit beeps.
The air conditioner runs in the Energy saving function.
The outer airflow blade moves up and down.
To stop the Energy saving function, press the again.
Note
You can select the Energy saving function only in the Cool mode.
3
Press the
button to adjust the temperature until the required
temperature is displayed.
You can set the temperature between 26°C and 30°C.
Note
If you want to adjust temperature under 26°C, cancel the Energy
saving function before adjusting the temperature.
4
Press the button to select the fan speed until the required
setting is displayed.
Note
The fan speed indicator increases and decreases continuously and
turns round each time you press the button.
5
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 15 2006-02-15 ¿ÀÈÄ 1:41:21
E-16
Selecting the Auto Cleaning Function
Remote Control
Control Panel
You can select the Auto Cleaning Function if you want to sterilize the
air conditioner or remove mold. Even when the air conditioner is turned off,
you can set this function.
1
If necessary, press the (On/Off) button.
Result:
The operation indicator on the indoor unit lights up.
The air conditioner starts up in the mode you selected last.
The indoor unit beeps.
2
Press the button.
Result: The indicator on the indoor unit lights up and the
Auto Cleaning function is set.
When you turn the air conditioner off, it operates the
Auto Cleaning function for 30 minutes.
After 30 minutes, the air conditioner turns off.
If you press the button when the air conditioner is turned off,
the air conditioner operates the Auto Cleaning Function for 30
minutes.
When the air conditioner
is turned
Mode Operating
On
Auto, Cool, Dry 30 minutes
Heat, Fan 15 minutes
Off 30 minutes
Note
The Auto Cleaning indicator is displayed only on the indoor unit.
3
Press the button again to stop the Auto cleaning function before the end
of the 30-minute period.
AS18HM_E_25309A(1).indd 16 2006-02-15 ¿ÀÈÄ 1:41:25
E-17
Selecting the Sound On/Off Function
You can turn on or off the sound of the air conditioner with the remote control.
1
Press the button.
Note
Each time you press the button, Sound On/Off function is
selected repeatedly.
On
Off
AS18HM_E_25309A(1).indd 17 2006-02-15 ¿ÀÈÄ 1:41:27
E-18
Selecting the Anions Function
The air conditioner can generate anions with an ionizer in the indoor unit.
Since it is an additional function, you can select it in any mode, even when the
air conditioner is turned off.
1
Press the button.
Result:
The air conditioner generates anions.
The indoor unit beeps.
Note
If you press the button when the air conditioner is off,
the air conditioner turns on automatically and generates anions
in the Fan mode with Low fan speed.
2
Press the button again to stop the Anions function.
Result: The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
4
To control the airflow direction, refer to page 19.
AS18HM_E_25309A(1).indd 18 2006-02-15 ¿ÀÈÄ 1:41:29
E-19
Adjusting the Airflow Direction Vertically
Adjusting the Airflow Direction Horizontally
You can adjust the airflow direction vertically. The outer airflow blade moves up
and down to increase the efficiency of the cooling or heating operation.
1
Press the button
until the required direction is set.
Result:
The outer blade is adjusted vertically.
2
Press the button
again to move the blade up and down automatically
during operation.
4
Press the button again to stop the blade moving up and down.
Note If you turn the air conditioner... Then the blade...
Off is closed completely.
On set to the default position.
You can adjust the airflow direction horizontally manually. The inner blades with
small fins moves the air in the required direction.
1
Adjust the inner blades by moving them to left or right.
AS18HM_E_25309A(1).indd 19 2006-02-15 ¿ÀÈÄ 1:41:31
E-20
Setting the On Timer
To Cancel the On Timer
Press the button to cancel the On Timer.
Note
If you press the button, both the On Timer and the Off Timer are
canceled.
You can set the On Timer to turn on the air conditioner automatically
at the appointed time. You can set the time from 30 minutes to 24 hours.
1
Press the button until the required time is displayed to set the On Timer.
You can set the time between 0.5 hour and 24 hours.
2
Press the button to complete the setting.
Result: The remaining time is displayed.
The timer indicator stops blinking.
The selected mode and the temperature on the display
disappear after 10 seconds.
The air conditioner turns on automatically at the appointed time
and the On Timer setting disappears.
3
Press the button until the desired mode is displayed at the top of the remote
control to select the mode in advance.
Result:
The air conditioner operates in the selected mode when it is turned on.
AS18HM_E_25309A(1).indd 20 2006-02-15 ¿ÀÈÄ 1:41:35
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
