Marvel ML24FAP2LP Le manuel du propriétaire

Marque: Marvel

Modèle: ML24FAP2LP

Catégorie: Réfrigérateurs-congélateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

Freezers

Congélateurs

ML24FA

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

NOTE

CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product Dimensions ...........................................................8

Starting your appliance ..................................................10

Using your Electronic control ............................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................11

Adjusting the temperature .............................................11

Temperature mode ........................................................11

Control lock ....................................................................11

Temperature sensor error codes ...................................12

Alarms ............................................................................12

Door ajar ...................................................................12

Power failure .............................................................13

Temperature alarm ....................................................13

Vacation mode .............................................................13

Overlay door panel installation .........................................14

Shelving congurations .....................................................18

Care and cleaning .............................................................20

Energy saving tips ............................................................20

Obtaining service .............................................................21

Troubleshooting ................................................................22

Warranty ...........................................................................23

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

Death or serious injury could result if...

NOTE

CAUTION

XXXXXXXXXXXX

UNPACKING YOUR APPLIANCE

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

MARVEL

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

Online registra-

tion available at

www.marvelrefrig-

eration.com

CAUTION

WARNING

An optional stacking kit is required to stack products.

Failure to use a stacking kit could result in personal

injury. Contact your dealer or Marvel customer service

at 800-223-3900 to order.

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unob-

structed. Overlay door models with articulated hinges are

intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Model Door Style

Minimum

Height

Maximum

Height

ML24* (S)

⁄4"

(85.7 cm)

⁄4"

(88.3 cm)

ML24* (P)

34"

(86.4 cm)

35"

(88.9 cm)

Table A

NOTE

Figure 6

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Front grille screw

Front grille

Figure 5

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

CAUTION

NOTE

Bottom View of

Freezer

Anti-Tip

Bracket

Leveling Leg

Front of cabinet

⁄2"

(54.6 cm)

Figure 7

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the freezer as shown in Figure 7.

Step by step instructions for locating the

position of the bracket:

1) Decide where you want to place the freezer. Slide it into

place, being careful not to damage the oor, leaving 1" (2.5

cm) of clearance from the rear wall to allow room for the

anti-tip bracket.

2) Raise the rear leveling legs approximately

⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the freezer is in the desired location, then

mark on the oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the oor marking the front corner

of the cabinet, excluding the door. Slide the freezer out of

the way. From the temporary line extend the sidewall line

back 21

⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the oor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete oor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

WARNING

If your freezer is not located under a counter top (free

standing), you must use an anti-tip device installed as

per these instructions. If the freezer is removed from

its location for any reason, make sure that the device

is properly engaged with the anti-tip bracket when

you push the freezer back into the original location. If

the device is not properly engaged, there is a risk of

the freezer tipping over, with the potential for property

damage or personal injury.

INSTALLING THE ANTI TIP DEVICE

FOR FREESTANDING INSTALLATIONS

⁄2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Side of cabinet line

Figure 8

Front of cabinet line

Rear of cabinet line

Rear Leveling leg

Screw

Figure 8a

NOTE

When the oor mounted anti-tip bracket is used the mini-

mum adjusted height of the cabinet is increased by

⁄8" (9 mm).

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

ML24FA(S)

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(65.2 cm)

⁄32"

(117.9 cm)

⁄16"

(65.2 cm)

ML24FA(P)

24"

(61 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

* 24"

(61 cm)

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄8"

(58.1 cm)

⁄2"

(118.1 cm)

⁄8"

(58.7 cm)

DOOR STYLE

(S) Solid Door

(P) Solid Overlay Door (no handle)

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

PRODUCT DIMENSIONS

Figure 9

Figure 9a

Figure 10

"F"

⁄2"

(54.6 cm)

* To install (P) models with the door face ush with adja-

cent cabinetry doors, custom decorative panel thickness

cannot exceed

⁄4" (19 mm).

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

ML24FA(S) 115V/60Hz/15A

140 lbs

(63.6 kg)

ML24FA(P) 115V/60Hz/15A

140 lbs

(63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 11

WARNING

Floor mount Anti-tip Bracket must be installed for freestand-

ing applications. Not required for built in applications.

STARTING YOUR APPLIANCE

Power Failure

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad Display Area

Lock

keypad

System Status

indicators

Figure 12

Electronic single zone control

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 12).

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 12).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, changing the interior lights, and activating vaca-

tion mode), the control must be awake.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

ALARM RESET

NOTE

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt.

• Sizzling and popping sounds from water dripping on

the heater element.

• A faint reddish glow in the freezer compartment from

the electric heater element.

These are all “normal” operating characteristics related to

refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

Using your electronic control:

USING YOUR ELECTRONIC CONTROL

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator,

and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc"

then immediately release your nger from the keypad.

Adjusting the temperature:

To set or check the set-point temperature (with the control

out of sleep mode), press the "-" or "+" keypads. "SET" will

be indicated on the user interface panel and the current

set-point temperature will display and ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off" key-

pad to accept, or do nothing and the "Set" mode will time-

out in 10-seconds accepting the displayed temperature as

the new set-point.

The available set-point temperature range for your appli-

ance is -10°F (-23°C) to 10°F (-12°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notication.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

NOTE

If the control lock is active (illuminated lock icon) the

control will have to be unlocked before using the key-

pad to reset an alarm condition. See page 11 (Control

Lock) for instructions for unlocking the control.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

NOTE

Loading warm contents may trigger a temperature alarm,

see temperature alarm page 13. Depending on the quantity

and/or weight of warm contents, it may take 48 hours for

the compartment temperature to stabilize.

USING YOUR ELECTRONIC CONTROL

Door Ajar

ALARM RESET

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

Temperature Sensor Error Codes

Sensor

Displayed

Code

Error

Description Action to Take

Single Zone

Temperature Sensor

Failed temperature sensor in the single

zone compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced

and remove all perishable

goods from compartment to

prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and

surrounding oor.

Unplug the power cord

immediately and call service

to have the defrost sensor

replaced.

The temperature sensors are monitored continuously. Any OPEN or SHORTED circuit condition will initiate an ERROR

CODE as listed below:

Temperature Sensor Error Codes

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by closing the door

or momentarily pressing the "On/Off" keypad, (i.e.-if

you are cleaning the storage compartment, etc.). The

alarm will recur in 5-minutes if the alarm condition

persists.

USING YOUR ELECTRONIC CONTROL

ALARM RESET

Power Failure

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

ALARM RESET

Temp

NOTE

Door Ajar

Temp

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

This alarm condition can be reset by momentarily

pressing the "On/Off" keypad. If this alarm occurs it

is recommended that you check the condition of your

stored contents, even though the appliance is operat-

ing normally and the temperature has recovered, as

prolonged temperature excursions could spoil perish-

ables.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

OVERLAY DOOR PANEL INSTALLATION

WARNING

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

WARNING

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

⁄8" (15

mm) and

⁄4" (18 mm) are accommodated.

Figure 13

Figure 13b

Bottom of

door

Figure 13a

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 13b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 14.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

⁄2 inch and

remove the hinges and door from the unit.

"P" clamp

and screw

Wire connector

see Figure 14

Cabinet

"Z" Bracket

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

CAUTION

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

Step 2: Remove the door gasket

With the door laying on a at surface and starting at a

corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 15. Set the gasket

aside on a at surface.

There are 10 holes in the gasket retainer extrusions, (3 on

each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack.

Figure 14

Press and hold down this

tab on the wire connec-

tor and pull the connector

apart.

Figure 15

Figure 15a

Overlay panel

ush with top

of door.

Holes in

gasket

retainer.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

OVERLAY DOOR PANEL INSTALLATION

Step 3: Cut and drill the overlay panel

Depending on your model cut the overlay door panel to the

dimensions shown in Figures 16 to 19.

Overlay panel to

be centered on

width of door.

Figure 17

Left Hand Hinged Door

24" (61 cm) wide appliance

CAUTION

OVERLAY DOOR PANEL INSTALLATION

Weight of overlay door panel must not

exceed 15 pounds (6.8 kg) for a solid

door model.

Figure 19

Right Hand Hinged Door

24" (61 cm) wide appliance

⁄32"

(77.1 cm

⁄32"

(77.1 cm

⁄4"

(60.3 cm)

1" (2.5 cm) diameter

⁄4" (6 mm) deep

4 places

⁄8"

(12.4 cm)

⁄16"

(3 cm)

14"

(35.6 cm)

⁄4" (6 mm)

radius is

permissible

⁄8"

(7.9 cm)

⁄4"

(4.4 cm)

(5.1 cm)

⁄16"

(9.4 cm)

⁄2"

(3.8 cm)

typical

⁄4"

(6 mm)

Deep

⁄16"

(4.3 cm)

Hinge side of door

Top of door

Clearance for hinge

at top and bottom

Clearance for hinge

at top and bottom

Clearance for

screw head,

4 places

Figure 16

Left Hand Hinged Door

24" (61 cm) wide appliance

⁄4"

(60.3 cm)

1" (2.5 cm) diameter

⁄4" (6 mm) deep

4 places

⁄8"

(12.4 cm)

⁄16"

(3 cm)

14"

(35.6 cm)

⁄4" (6 mm)

radius is

permissible

⁄8"

(7.9 cm)

⁄4"

(4.4 cm)

(5.1 cm)

⁄16"

(9.4 cm)

⁄2"

(3.8 cm)

typical

⁄4"

(6 mm)

Deep

⁄16"

(4.3 cm)

Hinge side of door

Top of door

Clearance for

screw head,

4 places

Figure 18

Right Hand Hinged Door

24" (61 cm) wide appliance

This side

facing interior

This side

facing interior

⁄32"

(2.9 cm)

⁄32"

(2.9 cm)

OVERLAY DOOR PANEL INSTALLATION

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom overlay panel should be

ush with the top of the door and centered along the width

of the door. See Figure 15a. Drill holes through the gasket

extrusion using the 10 holes as pilot holes. Use the drill

size from the chart in Table "B", being careful not to drill

through the front surface of the panel. If the overlay panel is

thinner than

⁄8" (16 mm) thick shorter screws will have to be

obtained. Fasten the panel to the door with the 10 screws

provided in the literature pack. (See Figure 20). Remove

the clamps and replace the gasket in the gasket extrusion

channels of the door. Some force may be required to seat

the gasket into the channels. Be sure the gasket corners

are seated properly.

Table B

Material Type #10 Wood Screw

Hardwood

⁄8" (3.2 mm) Diameter. Pilot Hole

Softwood

⁄64 (2.8 mm) Diameter. Pilot Hole

Figure 20

#10 x 1/2"

screw

Step 5: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figures 13 and

13a). Place wire harness from the grille and mount to the

bottom of the door with the screw and "P" clamp removed

in step 1. (See Figure 13b). Reconnect the wire harness,

(See Figure 14).

Step 6: Secure the cabinet

Use the #8 x

⁄4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

Cabinet

"Z" bracket

#8 x

⁄4" black

screws

(3 places)

Figure 21

Figure 22

SHELVING CONFIGURATIONS

Freezer:

Loading Tips and Suggestions

Your appliance is equipped with a cantilever shelf and

basket system which provides maximum adjustability and

customizing of the storage arrangements listed below.

24" (61 cm) Wide Models:

Shown with a solid door. Figure 22.

(2) pull-out metal baskets

(1) full depth perforated

metal shelf.

Figure 23

Perforated metal shelf

To remove the basket:

Press this tab on each

side of the basket slide

and pull the basket out

of the slides.

To install the basket:

Insert the basket slides into the ends of the cabinet

slides and push the basket completely closed. The

slide members will automatically lock together.

Figure 24

Figure 24a

To install or remove a shelf:

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

25b). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Rear tang

(hook) on

shelf

Shelf support

slot

Installed shelf

tang

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

CAUTION

Grasp the shelf by the front with

both hands and rotate the front

of the shelf up, then lift the shelf

up and remove the shelf from the

shelf ladders.

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

SHELVING CONFIGURATIONS

Figure 25a

Figure 25

Figure 25b

CARE AND CLEANING AND ENERGY SAVING TIPS

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

CAUTION

La page charge ...

Marvel ML24FAP2LP Le manuel du propriétaire

Marque: Marvel

Modèle: ML24FAP2LP

Catégorie: Réfrigérateurs-congélateurs

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel ML24FAP2LP Owner's manual

Marvel ML24FAP2LP Le manuel du propriétaire

Ce manuel convient également à

Marvel ML24FAP2LP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents