Simplicity 040358-03 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Not for
Reproduction
Operator’s Manual
Standby Generator System
This generator is rated in accordance with UL (Underwriters Laboratories)
2200 (stationary engine generator assemblies) and CSA (Canadian
Standards Association) standard C22.2 No. 100-4 (motors and generators).
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA.
317682
Revision ( C )
Not for
Reproduction
Thank you for purchasing this quality-built Milbank
®
home generator. We’re pleased that you’ve placed your
confidence in the Milbank brand. When operated and maintained according to the instructions in the operator’s
manual, your home generator will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with standby
generators and how to avoid them. This product is only for use as an optional generator system which provides an
alternate source of electric power and to serve loads such as heating, refrigeration systems, and communication
systems that, when stopped during any power outage, could cause discomfort or inconvenience.
Save these original instructions for future reference.
This generator requires professional installation before use. The installer should follow the
instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow
Pages. There are thousands of Milbank authorized service dealers worldwide who provide quality service. You can
also contact Technical Service by phone at 816-410-7346, or click on Find a Dealer at milbankmfg.com, which
provides a list of authorized dealers.
Generator and engine model and serial numbers should be recorded in the installation manual.
DATE OF PURCHASE
GENERATOR
Model Number
Model Number
Model Revision
Serial Number
ENGINE
Not for
Reproduction
3
Table of Contents
Important Safety Instructions .....................4
Installation .....................................7
Owner Orientation ........................................ 7
Fuel Factors ............................................. 8
Delivery Inspection ...................................... 10
Controls.......................................11
Access Panels .......................................... 13
System Control Panel .................................... 15
Operation .....................................19
Engine Oil.............................................. 19
Battery ................................................ 19
15 Amp Fuse ........................................... 19
Automatic Operation Sequence ............................ 19
Maintenance ...................................20
Service Code Detection System ........................... 20
Generator Maintenance..........................23
Engine Maintenance ..................................... 25
Adjust Valve Lash ....................................... 25
Service Air Cleaner ...................................... 27
Service Spark Plugs ..................................... 28
Troubleshooting................................29
Generator Specifications ........................31
Engine Specifications ...........................31
Common Service Parts ..........................31
Not for
Reproduction
4
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation and maintenance of the generator and
batteries.
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol
to designate a degree or level of hazard seriousness.
A safety symbol may be used to represent the type of
hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE addresses practices not related to personal injury.
The manufacturer cannot possibly anticipate every possible
circumstance that might involve a hazard. The warnings
in this manual, and the tags and decals affixed to the unit
are, therefore, not all-inclusive. If you use a procedure, work
method or operating technique that the manufacturer does
not specifically recommend, you must satisfy yourself that
it is safe for you and others. You must also make sure that
the procedure, work method or operating technique that you
choose does not render the generator system unsafe.
Explosion
Fire
Electrical Shock
Rotating Parts
Hot Surface
Toxic Fumes
Chemical BurnExplosive PressureAuto Start
Lift Hazard
Read Manual
WARNING Running engine gives off carbon
monoxide, an odorless, colorless, poison gas.
Breathing carbon monoxide could result in
death, serious injury, headache, fatigue,
dizziness, vomiting, confusion, seizures,
nausea or fainting.
Operate this product ONLY outdoors in an area that
will not accumulate deadly exhaust gas.
Keep exhaust gas away from any windows, doors,
ventilation intakes, soffit vents, crawl spaces, open
garage doors or other openings that can allow
exhaust gas to enter inside or be drawn into a
potentially occupied building or structure.
Carbon monoxide detector(s) MUST be installed
and maintained indoors according to the
manufacturer’s instructions/recommendations.
Smoke alarms cannot detect carbon monoxide gas.
WARNING Storage batteries give off explosive
hydrogen gas during recharging.Slightest spark
will ignite hydrogen and
cause explosion, resulting in
death, serious injury, and/or
property damage.Battery electrolyte fluid contains
acid and is extremely caustic.Contact with battery
contents will cause severe chemical burns.A battery
presents a risk of electrical shock and high short
circuit current.
DO NOT dispose of battery in a fire. Recycle
battery.
DO NOT allow any open flame, spark, heat, or
lit cigarette during and for several minutes after
charging a battery.
DO NOT open or mutilate the battery.
Wear protective goggles, rubber apron, rubber
boots and rubber gloves.
Remove watches, rings, or other metal objects.
Use tools having insulated handles.
WARNING The engine exhaust from this product
contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.
WARNING Certain components in this product
and related accessories contain chemicals known to
the State of California to cause cancer, birth defects, or
other reproductive harm. Wash hands after handling.
Save These Instructions
Not for
Reproduction
5
WARNING Generator produces hazardous voltage.
Failure to properly ground generator could result in
electrocution.Failure to isolate generator from utility
power could result in death or serious injury to electric
utility workers due to backfeed of electrical energy.
When using generator for backup power, notify
utility company.
DO NOT touch bare wires or bare receptacles.
DO NOT use generator with electrical cords which
are worn, frayed, bare or otherwise damaged.
DO NOT handle generator or electrical cords while
standing in water, while barefoot, or while hands or
feet are wet.
If you must work around a unit while it is operating,
stand on an insulated dry surface to reduce the risk
of a shock hazard.
DO NOT allow unqualified persons or children to
operate or service generator.
In case of an accident caused by electrical shock,
immediately shut down the source of electrical
power and contact the local authorities. Avoid
direct contact with the victim.
Despite the safe design of the generator, operating
this equipment imprudently, neglecting its
maintenance or being careless can cause possible
injury or death.
Remain alert at all times while working on this
equipment. Never work on the equipment when you
are physically or mentally fatigued.
Before performing any maintenance on the
generator, disconnect the battery cable indicated
by a NEGATIVE, NEG or (-) first. When finished,
reconnect that cable last.
After your system is installed, the generator may crank
and start without warning any time there is a power
failure. To prevent possible injury, always set the
generator’s system switch to OFF, remove the service
disconnect from the disconnect box AND remove the
15 Amp fuse BEFORE working on the equipment.
WARNING Propane and Natural Gas are
extremely flammable and explosive,
which could cause burns, fire or
explosion resulting in death, serious
injury and/or property damage.
DO NOT operate the equipment if the “fuel shut-off”
valve is missing or inoperative.
Install the fuel supply system according to NFPA 37
and other applicable fuel-gas codes.
Before placing the generator into service, the fuel
system lines must be properly purged and leak
tested.
After the generator is installed, you should inspect
the fuel system periodically.
NO leakage is permitted.
DO NOT operate engine if smell of fuel is present or
other explosive conditions exist.
DO NOT smoke around the generator. Wipe up any
oil spills immediately. Ensure that no combustible
materials are left in the generator compartment. Keep
the area near the generator clean and free of debris.
WARNING Starter and other rotating parts can
entangle hands, hair, clothing, or accessories
resulting in serious injury.
NEVER operate generator without protective
housings, covers, or guards in place.
DO NOT wear loose clothing, jewelry or anything that
may be caught in the starter or other rotating parts.
Tie up long hair and remove jewelry.
Before servicing, remove 15 Amp fuse from control panel
and disconnect Negative (NEG or -) battery cable.
Not for
Reproduction
6
NOTICE Improper treatment of generator can
damage it and shorten its life.
Use generator only for intended uses.
If you have questions about intended use, contact
your authorized dealer.
Operate generator only on level surfaces.
Adequate, unobstructed flow of cooling and ventilating
air is critical to correct generator operation.
The Oil Fill, Oil Drain and the Control Panel doors
must be installed whenever the unit is running.
DO NOT expose generator to excessive moisture,
dust, dirt, or corrosive vapors.
Despite the safe design of the generator, operating this
equipment imprudently, neglecting its maintenance or
being careless can cause possible injury or death.
Remain alert at all times while working on this
equipment. Never work on the equipment when you
are physically or mentally fatigued.
DO NOT start engine with air cleaner or air cleaner
cover removed.
DO NOT insert any objects through cooling slots.
DO NOT use the generator or any of its parts as
a step. Stepping on the unit can cause stress and
break parts. This may result in dangerous operating
conditions from leaking exhaust gases, fuel leakage,
oil leakage, etc.
If connected devices overheat, turn them off and
disconnect them from generator.
Shut off generator if:
-electrical output is lost;
-equipment sparks, smokes, or emits flames;
-unit vibrates excessively:
-unit makes unusual noises.
CAUTION Installing the 15A fuse could cause
the engine to start at any time without warning
resulting in minor or moderate injury.
Observe that the 15 Amp fuse has been removed
from the control panel for shipping.
DO NOT install this fuse until all plumbing and wiring
has been completed and inspected.
CAUTION Excessively high operating speeds
could result in minor injury and/or equipment
damage.Excessively low speeds impose a heavy
load on generator.
DO NOT tamper with governed speed. Generator
supplies correct rated frequency and voltage when
running at governed speed.
DO NOT modify generator in any way.
WARNING
Exhaust heat/gases could ignite
combustibles or structures resulting in
death, serious injury and/or property
damage. Contact with muffler area could
cause burns resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
Exhaust outlet side of weatherproof enclosure must
have at least 5 ft. (1.5 m) minimum clearance from
any structure, shurbs, trees or any kind of vegetation.
Standby generator weatherproof enclosure must be at
least 5 ft. (1.5 m) from windows, doors, any wall opening,
shrubs or vegetation over 12 inches (30.5 cm) in height.
Standby generator weatherproof enclosure must
have a minimum of 5 ft. (1.5 m) overhead clearance
from any structure, overhang or trees.
DO NOT place weatherproof enclosure under a deck
or other type of structure that may confine airflow.
Use only flexible fuel line provided. Connect
provided fuel line to generator, DO NOT use with or
substitute any other flexible fuel line.
Smoke detector(s) MUST be installed and
maintained indoors according to the manufacturer’s
instructions/recommendations. Carbon monoxide
alarms cannot detect smoke.
Keep at least minimum distances shown in General
Location Guidelines to insure for proper generator
cooling and maintenance clearances.
It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any
forest-covered, brush-covered, or grass-covered
land unless the exhaust system is equipped with
a spark arrester, as defined in Section 4442,
maintained in effective working order. Other states
or federal jurisdictions may have similar laws.
Contact the original equipment manufacturer,
retailer, or dealer to obtain a spark arrester designed
for the exhaust system installed on this engine.
Replacement parts must be the same and installed
in the same position as the original parts.
Not for
Reproduction
7
Installation
We sincerely appreciate your patronage. For this
reason, we have made every effort to provide for a safe,
streamlined and cost-effective installation. Because
each installation is unique, it is impossible to know of
and advise the trade of all conceivable procedures and
methods by which installation might be achieved. Neither
could we know of possible hazards and/or the results of
each method or procedure. For these reasons,
Only current licensed electrical and plumbing
professionals should attempt home generator system
installations. Installations must strictly comply with all
applicable codes, industry standards and regulations.
Your home generator is supplied with this “Operator’s
Manual” and a separate “Installation Manual”. These
are important documents and should be retained by the
owner after the installation has been completed.
This product is only for use as an optional generator system
which provides an alternate source of electric power and
to serve loads such as heating, refrigeration systems, and
communication systems that, when stopped during any
power outage, could cause discomfort or inconvenience.
NOTICE This product does NOT qualify for either an
emergency standby or legally required standby system
as defined by NFPA 70 (NEC).
Emergency generator systems are intended
to automatically supply illumination, power,
or both, to designated areas and equipment
in the event of failure of the normal supply.
Emergency systems may also provide power for
such functions as ventilation where essential to
maintain life, where current interruption of the
normal supply would produce serious life safety
or health hazards.
Legally Required standby generator systems
are intended to automatically supply power
to selected loads in the event of failure of the
normal source which could create hazards or
hamper rescue or fire-fighting operations.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
Only current licensed electrical and plumbing professionals
should attempt home generator system installations.
Installations must strictly comply with all applicable codes,
industry standards, laws and regulations.
For the Home Owner:
To help you make informed choices and communicate
effectively with your installation contractor(s), read and
understand Owner Orientation in this manual before
contracting or starting your generator installation.
To arrange for proper installation, contact the store at
which you purchased your generator, your dealer, a
licensed electrician or your utility power provider.
The generator warranty is VOID unless the
system is installed by licensed electrical and
plumbing professionals.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
The Emission Control System for this generator is warranted
for standards set by the U.S. Environmental Protection
Agency and by the California Air Resources Board (CARB).
For the Installing Dealer/Contractor:
For most applications, the installation manual contains
all the information required to properly install and
start the generator. This operator’s manual describes
routine operation and owner maintenance procedures.
If you need more information in this matter, please call
at 800-743-4115 between 8:00 AM and 5:00 PM CT.
Owner Orientation
This section provides generator owners with the
information necessary to achieve the most satisfactory
and cost effective installation possible.
The illustrations are for typical circumstances and
are meant to familiarize you with the installation
options available with your generator. A thorough
understanding of these options will provide
fundamental control over the cost of your installation,
as well as ensure your final satisfaction and security.
Federal and local codes, appearance, noise levels,
fuel types, and distances are the factors that must
be considered when negotiating with an installation
professional. Remember that as the distance from the
existing electrical service and gaseous fuel supply
increases, and the number of 90 degree bends in the
fuel supply increases, compensations in piping and
wiring materials must be made. This is necessary
to comply with local codes and overcome electrical
voltage drops and gaseous fuel pressure drops.
The factors mentioned above will have a direct affect
on the overall price of your generator installation.
In some areas you may need to acquire electrical
permits for installing the generator, building permits for
installing gas lines, and permits for noise allowances.
Your installer should check your local codes AND
obtain the permits before installing the system.
Not for
Reproduction
8
Fuel Factors
An important consideration affecting the entire
installation is the type of fuel used by your generator.
The system was factory tested and adjusted using
either natural gas or liquid propane (LP vapor). For
proper engine function, factors that are inherent to
each of these fuels, your location and the duration
of possible utility interruptions are important
considerations in the following fuel guidelines:
Use clean, dry fuel, free of moisture or any
particulate material. Using fuels outside the
following recommended values may cause
performance problems.
In engines set up to run on propane (LP),
commercial grade HD5 propane with a minimum fuel
energy of 2500 BTUs/ft
3
with maximum propylene
content of 5% and butane and heavier gas content
of 2.5% and minimum propane content of 90%.
Natural gas rating will depend on specific fuel but typical
derates are between 10 to 20% off the LP gas rating.
Natural gas or LP engines are certified to operate on
natural or liquid propane gas. The emissions control
system for this engine is EM (Engine Modifications).
Power Decrease at High Altitude or High
Temperature
Air density is less at high altitudes, resulting in less
available engine power. Specifically, engine power
will decrease 3.5% for each 1,000 feet (300 meters)
above sea level and 1% for each 10° F (5.6°C) above
77°F (25°C). Make sure you and your installer consider
these factors when determining total generator load.
WARNING Propane and Natural Gas are
extremely flammable and explosive,
which could cause burns, fire or
explosion resulting in death, serious
injury and/or property damage.
The residential generator is equipped with an
automatic safety gas “fuel shut-off” valve.
DO NOT operate the equipment if the “fuel shut-off”
valve is missing or inoperative.
Not for
Reproduction
9
Generator Location
The actual physical location of your generator has a
direct affect on:
1. The amount of plumbing required to fuel
your generator.
2. The amount of wiring required to control and
connect your generator.
Specific location guidelines are discussed in the
installation manual. Acquaint yourself with that
information and confer with your installer. Be sure to
ask how your site might affect installation costs and
compliance with local codes and standards.
Install generator outdoors in an area that will not
accumulate deadly exhaust gas.
DO NOT install generator where exhaust gas
could accumulate and enter inside or be drawn
into a potentially occupied building or structure.
By law it is required in many states to have a
Carbon Monoxide (CO) detector in operating
condition in your home. Carbon monoxide
detector(s) (A) MUST be installed and maintained
indoors according to the manufacturer’s
instructions/recommendations. A CO monitor is an
electronic device that detects hazardous levels of
CO. When there is a buildup of CO, the monitor
will alert the occupants by flashing visual indicator
light and alarm. Smoke alarms cannot detect CO
gas.
Ensure exhaust gas is kept away from any
windows, doors, ventilation intakes, soffit vents,
crawl spaces, open garage doors or other
openings that can allow exhaust gas to enter
inside or be drawn into a potentially occupied
building or structure. Your neighbor’s home may
be exposed to the engine exhaust from your
standby generator and must be considered when
installing your standby generator.
Wind and air currents should be taken into
consideration when positioning generator.
See the installation manual for full details on safe
generator location.
WARNING Running engine gives off carbon
monoxide, an odorless, colorless, poison
gas. Breathing carbon monoxide could result
in death, serious injury, headache, fatigue,
dizziness, vomiting, confusion, seizures, nausea or
fainting.
Operate this product ONLY outdoors in an area that
will not accumulate deadly exhaust gas.
Keep exhaust gas away from any windows, doors,
ventilation intakes, soffit vents, crawl spaces, open
garage doors or other openings that can allow
exhaust gas to enter inside or be drawn into a
potentially occupied building or structure.
Carbon monoxide detector(s) MUST be installed
and maintained indoors according to the
manufacturer’s instructions/recommendations.
Smoke alarms cannot detect carbon monoxide gas.
A
WARNING Exhaust heat/gases could ignite
combustibles or structures resulting in death,
serious injury and/or property damage.
Exhaust outlet side of weatherproof enclosure must
have at least 5 ft. (1.5 m) minimum clearance from
any structure, shrubs, trees, or any kind of vegetation.
Standby generator weatherproof enclosure must be at
least 5 ft. (1.5 m) from windows, doors, any wall opening,
shrubs or vegetation over 12 in. (30.5 cm) in height.
Standby generator weatherproof enclosure must
have a minimum of 5 ft. (1.5 m) overhead clearance
from any structure, overhang or trees.
DO NOT place weatherproof enclosure under a deck
or other type of structure that may confine airflow.
USE ONLY flexible fuel line provided. Connect
provided fuel line to generator. DO NOT use with or
substitute any other flexible fuel line.
Smoke detector(s) MUST be installed and
maintained indoors according to the manufacturer’s
instructions/recommendations. Carbon monoxide
alarms cannot detect smoke.
DO NOT place weatherproof enclosure in manner
other than shown in illustrations.
Not for
Reproduction
10
Delivery Inspection
Carefully inspect the generator for any damage that
may have occurred during shipment.
If loss or damage is noted at time of delivery, have
the person(s) making delivery note all damage
on the freight bill and affix his signature under the
consignor’s memo of loss or damage. If loss or
damage is noted after delivery, separate the damaged
materials and contact the carrier and your installer for
claim procedures. Missing or damaged parts are not
warranted.
The home generator system is supplied with:
Oil (5W30 Synthetic)
Flexible steel fuel line
Installation and start-up manual
Operator’s manual
Spare access roof keys
Spare 15 Amp ATO-type fuse
Not included:
Carbon monoxide detector(s)
Smoke detector(s)
Starting battery
Connecting wire and conduit
Fuel supply valves/plumbing
Crane, lifting straps, chains or cables
Two 60” lengths of 3/4” nominal minimum
scheduled 40 steel pipe (NOT conduit)
Torque screwdriver, 5 to 50 inch-pound range
Voltage/frequency meter
Not for
Reproduction
11
Controls
15kW, 16kW and 20kW Generator (Front View)
Read this Operator’s Manual and Important Safety Instructions before operating your generator.
Compare the illustrations with your generator to familiarize yourself with the locations of various controls
and adjustments. Save this manual for future reference.
Generator is shown with roof and access covers
removed for clarity.
A - Lifting Holes — Provided at each corner for lifting
generator.
B - Alternator — An electrical machine that generates
an alternating current
C - Muffler — High-performance muffler lowers engine
noise to comply with most residential codes.
D - Circuit Breaker — Protects the system from shorts
and other over-current conditions.
E - Control Board — Used for generator operation
control, menu start-up, and informational display
functions.
F - Air Cleaner — Uses a dry type filter element to
protect engine by filtering dust and debris out of
intake air.
G - Engine Label — Identifies engine model and type
H - Spark Plug — A device in the cylinder head of the
engine that ignites the fuel mixture by means of an
electric spark.
J - Oil Filter — Filters engine oil to prolong generator
life.
K - Battery (installer supplied) — 12 Volt DC, lead
acid, automotive style battery provides power to
start the engine.
L - Oil Heater Port/ Oil Drain Hose Port — Provided
to allow an optional heating element to be installed.
Provided to facilitate oil changing.
M - Generator Data Label — Identifies generator
model number and serial number. Located inside
battery access compartment.
A
B
C
D
E
F
G
H
J
K
L
M
Not for
Reproduction
12
15kW, 16kW and 20kW Generator (Back View)
Read this Operator’s Manual and Important Safety Instructions before operating your generator.
Compare the illustrations with your generator to familiarize yourself with the locations of various controls
and adjustments. Save this manual for future reference.
Generator is shown with roof and access covers
removed for clarity.
A - Lifting Holes — Provided at each corner for lifting
generator.
B - Fuel Solenoid — Automatically opens and closes
to supply fuel to unit when needed.
C - Fuel Regulator — Controls fuel flow to engine for
proper operation.
D - Fuel Selector Valve — Used to select proper fuel
type (LP or NG).
E - Spark Plug — A device in the cylinder head of the
engine that ignites the fuel mixture by means of an
electric spark.
F - Oil Fill Cap — Location for adding oil to engine.
G - Electrical Field Wiring InletWires to and from
generator are centered in this location.
H - Air Cleaner — Uses a dry type filter element to
protect engine by filtering dust and debris out of
intake air.
J - Engine Oil Dipstick — Allows user to check engine
oil level easily.
K - Oil Heater Port — Provided to allow an optional
heating element to be installed to warm engine oil to
promote easy starting in cold climates.
A
B
C
D
E
F
G
H
J
K
Not for
Reproduction
13
Access Panels
The generator is equipped with an enclosure that has
several access panels, as shown.
The access panels and the components located
behind them are listed below:
A - Roof (Control Panel, air filter, oil dipstick, and circuit
breaker)
B - Front Access Panel (oil drain and oil filter)
C - Battery Panel (battery and generator data label)
D - Rear Access Panel (fuel regulator, fuel selector, and
engine starter)
E - Control Panel Cover (field wiring and control wires)
Each generator is shipped with a set of identical keys.
These keys fit in the lock on the front removable panel.
The roof must be unlocked in order for it to open.
A
B
D
E
C
Not for
Reproduction
14
To open roof:
1. Insert key into lock (A) of front panel. Gently push
down on roof above the lock to aid in turning the
key. Turn key one quarter turn clockwise.
2. Lift roof to the open position.
To remove front panel:
1. Remove the two bolts (B) that secure the panel to the
unit.
2. Lift panel to remove from unit.
To secure front panel:
1. Place panel in unit.
2. Secure the panel with two bolts.
To remove rear panel:
1. Ensure the roof is in the open position.
2. Remove the two bolts (C) that secure the panel to
the unit.
3. Lift panel to remove from unit.
To secure rear panel:
1. Slide panel into place on unit.
2. Secure the panel with two bolts.
To remove battery panel:
1. Ensure the roof is in the open position.
2. Remove the two bolts (D) that secure the panel to
the unit.
3. Lift up on panel and remove.
To secure battery panel:
1. Place panel in unit.
2. Secure the panel with two bolts.
A
B
C
D
Not for
Reproduction
15
System Control Panel
Compare this control panel illustration with your generator to familiarize yourself with the location of these important controls:
A - Menu/Programming Navigation Buttons — See
Menu section for details
B - Mini USB Port — Authorized Dealer Service Use
Only
C - Generator Operation Control Buttons —
•“AUTONormal operating position. Press and
hold button to put unit into Automatic mode. If
an utility power outage is sensed, the system
will start the generator. When utility power is
restored, auto lets the engine stabilize internal
temperatures, shuts o the generator, and waits
for the next utility outage.
•“OFFTurns o running generator, prevents unit
from starting, and resets any detected service
codes.
OFF must be pressed and held for more than 5
seconds in order to reset service codes.
•“MANUALUsed to manually start the generator.
“AUTO” LED — LED will light when unit is placed
into Auto mode. LED will blink if exercise cycle is
not set or set to OFF.
D 15 Amp Fuse — Protects the home generator
DC control circuits. If the fuse has ‘blown’ (melted
open) or was removed, the engine cannot crank
or start. Replace the fuse using only an identical
ATO 15A fuse. One spare fuse is supplied with
the unit.
E - Cover This protective cover must be opened to
access the fuse and the USB port.
F - Digital Display — Displays generator mode,
menu options, service codes, and service engine
indicators
MENU
ESC
AUTO OFF
MANUAL
A
B
C
F
E
D
Not for
Reproduction
16
Menu
MENU
ENTER THE MENU (VIEW SETTINGS)
PRESS TO CONFIRM SELECTION WHEN PROGRAMMING.
ESCAPE (EXIT) RETURN TO LAST MENU ITEM
RIGHT ARROW
TOGGLE THROUGH MENU OPTIONS
SETTING SYSTEM PARAMETERS
LEFT ARROW
TOGGLE THROUGH MENU OPTIONS
SETTING SYSTEM PARAMETERS
MANUAL MODE
USED TO MANUALLY START THE GENERATOR. PRESS AND
HOLD BUTTON TO START THE GENERATOR.
OFF
TURNS OFF RUNNING GENERATOR, PREVENTS UNIT FROM
STARTING, AND RESETS ANY DETECTED Service codeS.
AUTOMATIC MODE
NORMAL OPERATING POSITION. PRESS AND HOLD BUTTON TO
PUT UNIT INTO AUTOMATIC MODE. IF A UTILITY POWER OUTAGE
IS SENSED, THE SYSTEM WILL START THE GENERATOR.
WHEN UTILITY POWER IS RESTORED, AUTO LETS THE ENGINE
STABILIZE INTERNAL TEMPERATURES, SHUTS OFF THE
GENERATOR, AND WAITS FOR THE NEXT UTILITY POWER
OUTAGE.
GENERAL
SET-UP
PRESS AND HOLD [ARROW LEFT AND ARROW RIGHT]
FOR THREE SECONDS TO ENTER THE PROGRAM
MODE.
ADVANCED
SETTINGS
PRESS AND HOLD [ARROW LEFT, ARROW RIGHT AND
ESC] FOR THREE SECONDS TO ENTER THE ADVANCED
SETTINGS MODE.
WIRELESS
LINK MODE
PRESS AND HOLD [MENU AND ESC] FOR THREE
SECONDS TO ENTER THE WIRELESS LINKING MODE.
The following chart shows the icons for the buttons that control the system control panel:
The following chart describes key sequences for accessing different programming modes:
Not for
Reproduction
17
General Set Up Screen
For general set up, press and hold the left arrow and right arrow for 3 seconds. Follow the prompts as
outlined below.
NOTE Date and Time were set at the factory and stored in the control panel memory. The Exercise Cycle
was also set at the factory. The default exercise cycle occurs on Tuesdays, at 2:00 P.M. Central Standard
Time. To update or change these settings, follow the steps below.
IF DURING PROGRAMMING NO BUTTONS ARE PRESSED FOR 30 SECONDS,
THE CONTROL PANEL WILL AUTOMATICALLY EXIT THE PROGRAM MODE.
SET DATE
If set to OFF, display will read:
EXERCISE CYCLE OFF
or
YEAR
FLASHING
MONTH
FLASHING
DAY##
FLASHING
SET TIME
HOURS
FLASHING
MINUTES
FLASHING
AM/PM
FLASHING
or or or
or
or or or
or
or
or or or or
DAY OF WEEK
FLASHING
HOURS
FLASHING
MINUTES
FLASHING
AM/PM
FLASHING
SET EXERCISE CYCLE
EVENT LOG
Display will scroll last service code event, date, time,
and ambient temperature of when the event occurred.
or
Not for
Reproduction
18
Control Panel Prompts
Automatic Mode
In Automatic Mode, the display screen will display via
scrolling text:
GENERATOR READY - if the unit is in standby
and utility power is present.
GENERATOR ON - if the unit is running and utility
power is not present.
SERVICE CODE - if a system service code has
been detected.
General System Parameters
To view general system parameters, press the MENU
button.
The following will scroll across the digital display and
then move to the next item:
Run time
• Date
• Time
Exercise Cycle date and start time
The user can press the LEFT ARROW or RIGHT
ARROW at any time to move to the next item.
The user can press ESCAPE to go back to
GENERATOR READY.
If no user inputs are made for 10 seconds after all the
items have been displayed, the control board will reset
to
GENERATOR READY.
AUTOMATIC MODE
GENERATOR READY OR SERVICE CODE
DESCRIPTION
(When Generator NOT Running - Auto Mode)
GENERATOR ON
(When Generator Running - Auto Mode)
(MENU)
RUN TIME
or
or
or
TIME
DATE
EXERCISE CYCLE
Not for
Reproduction
19
Operation
Important Owner’s Considerations
Engine Oil
The engine is shipped from the factory pre-run and
filled with synthetic oil (API SJ/CF 5W-30). This allows
for system operation in a wide range of temperature
and climate conditions. Before starting the engine,
check oil level and ensure that engine is serviced as
described in Maintenance.
Battery
The installer must supply rechargeable 12 volt DC
starting battery. See Battery in Final Installation
Considerations in the installation manual.
With the battery installed, all wiring to transfer switch
and generator completed, utility power supplied to the
automatic transfer switch, and the unit in AUTO mode,
the battery receives a trickle charge while the engine
is not running. The trickle charge cannot be used to
recharge a battery that is
completely discharged.
15 Amp Fuse
The generator’s 15 Amp fuse is critical to correct
system operation. The 15 Amp fuse was removed
at the factory to prevent the unit from starting during
shipping. Your installer will ensure the fuse is properly
installed upon completion of the installation.
Automatic Operation Sequence
The generator’s control board constantly monitors
utility voltage. Should utility voltage drop below a
preset level, the control board will signal the engine to
crank and start.
When utility voltage is restored above a preset voltage
level, the engine is signaled to shut down.
The actual system operation is not adjustable and
is sequenced by sensors and timers on the control
board, as follows:
Utility Voltage Dropout Sensor
This sensor monitors utility source voltage.
If utility source voltage drops below about
70 percent of the nominal supply voltage, the
sensor energizes a 3 second timer. The timer is
used to ‘sense’ brown-outs.
Once the timer has expired, the engine will crank
and start.
Utility Voltage Pickup Sensor
This sensor monitors utility power voltage. When utility
voltage is restored above 80 percent of the nominal
source voltage, a time delay starts timing and the
engine will go to engine cool-down.
Engine Cool-down Timer
When utility power is sensed and the load transfers to
the utility source, the engine will go into a cool down
period as described below:
If the generator has run for MORE than 5 minutes,
once the utility transfer occurs, the engine will
continue to run for about 1 minute before shutting
down.
If the generator has run for LESS than 5 minutes,
once the utility transfer occurs, the engine will
continue to run until 5 minutes has elapsed before
shutting down.
CAUTION With the system switch set to AUTO,
the engine could crank and start at any
time without warning, resulting in minor or
moderate injury.
To prevent possible injury that may be caused by
such sudden starts, always set the system switch to
OFF if performing maintenance on the system.
Remove the 15 Amp fuse before working on or
around the generator or transfer switch.
NOTICE Any attempt to crank or start the engine
before it has been properly serviced with the
recommended oil will result in equipment failure.
DO NOT attempt to crank or start the engine before
it has been properly serviced with the recommended
oil. This may result in an engine failure.
Damage to equipment resulting from failure to follow
this instruction will void generator warranty.
WARNING Battery posts, terminals and related
accessories contain lead and lead compounds,
chemicals known to the State of California to
cause cancer and reproductive harm. Wash hands
after handling.
Not for
Reproduction
20
Setting Exercise Timer
The generator is equipped with an exercise timer.
During the exercise period, the unit runs for
approximately 20 minutes and then shuts down.
Electrical load transfer DOES NOT occur during the
exercise cycle (unless an utility power outage occurs).
The generator will only enter the exercise cycle if the
unit is in the AUTO mode and this exact procedure is
followed.
To set the exercise timer:
NOTICE The generator is set with a service code
exercise cycle setting of Tuesday at 2:00 P.M, Central
Time. To change the cycle setting, proceed to the
following steps:
1. Choose the day and time you want your generator
to exercise.
2. Press and hold the left arrow and right arrow
simultaneously for 3 seconds to enter the General
Set-Up program mode. See General Set-Up flow
chart in Menu Section.
3. Verify and/or set the time and date on the unit.
4. Go to the SET EXERCISE prompt and hit the “OK”
button.
NOTICE Items will flash until they are selected.
SELECT DAY: Use the left or right arrow to toggle
through the days of the week, Once the day is
selected, hit the “OK” button.
SELECT HOUR: Use the left or right arrow to
toggle through between 1 and 12. Choose the
hour of day you want the generator to exercise
then hit the “OK” button.
SELECT MINUTE: Use the left of right arrow to
toggle between :00 and :59. Choose the minute of
the day you want the generator to exercise then
hit the “OK” button.
SELECT AM/PM: Use the left of right arrow to
toggle between AM and PM. Once chosen, hit the
“OK” button.
NOTICE During the weekly exercise cycle, the
generator will run for 20 minutes, but it will not
supply power to the home. During the exercise
cycle, the in-home monitor will continue blinking the
GENERATOR READY green LED.
If you want to change the day and time the unit
exercises, simply perform the procedure again.
To turn off the generator exercise cycle, go to the OFF
selection within the day of the week menu and press
OK. The
display will then scroll: EXERCISE CYCLE
OFF.
Maintenance
Servicing the System
Before performing any generator maintenance, always
perform the following steps:
1. Set generator’s circuit breaker to its OFF position.
2. Press and hold the control board OFF button.
3. Remove 15 Amp fuse from control board.
4. Utility voltage is present at generator control
board. Disconnect power before servicing control
board by removing the fuses from the transfer
switch.
5. After all servicing has been completed, replace
fuses in transfer switch, replace 15 Amp fuse in
control board, set circuit breaker ON and press
and hold control board AUTO button.
Service Code Detection System
The generator may have to run for long periods of time
with no operator present. For that reason, the system
is equipped with sensors that automatically shut down
the generator in the event of potentially damaging
conditions, such as low oil pressure, high temperature,
over speed, and other conditions.
The generator’s control board shows service code
descriptions scrolling across the digital display. The
service code descriptions are listed below:
Low Battery Voltage
Low Oil Pressure
Under Voltage
Over Voltage
Engine Does Not Start
Low Frequency
Engine Overspeed
High Oil Temperature
Transfer Switch Service code
Battery Charge Circuit
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96

Simplicity 040358-03 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur