Powerware Powerware 9355 Manuel utilisateur

Powerware
Marque
Powerware
Modèle
Powerware 9355
Catégorie
Alimentations sans interruption (UPS)
Taper
Manuel utilisateur

Ce manuel convient également à

Powerware 9355 Tie Cabinet
Installation Guide
®
For use with Powerware 9355 20/30 kVA UPSs
Powerware, Powerware Hot Sync, and LanSafe are registered trademarks and X-Slot is a trademark of Eaton Power Quality Corporation. Greenlee
is a registered trademark of Greenlee Textron.
ECopyright 2006 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the
express written approval of Eaton Corporation.
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing Equipment Regulations ICES-003.
Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur du Canada.
IEC 62040-2
Some configurations are classified under IEC 62040-2 as “Class-A UPS for Unrestricted Sales Distribution.” For these configurations, the following
applies:
WARNING This is a Class A-UPS Product. In a domestic environment, this product may cause radio interference, in which case, the user may be
required to take additional measures.
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
S Harmonized Standards: EN 50091-1-1 and EN 50091-2; IEC 60950 Third Edition
S EU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
89/336/EEC, Council Directive relating to electromagnetic compatibility
92/31/EEC, Amending Directive 89/336/EEC relating to EMC
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: +358-9-452 661
Fax: +358-9-452 665 68
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the associated warning should
be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for additional information, such
as important operating and maintenance instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries in the trash. This product
contains sealed, lead-acid batteries and must be disposed of properly. For more information, contact your
local recycling/reuse or hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the
trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.
ON - Indicates that the switch is in the ON position.
OFF - Indicates that the switch is in the OFF position.
PHASE - The word “phase.”
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
i
Table of Contents
1 Introduction 1........................................................
2 Safety Warnings 3....................................................
3 Tie Cabinet Installation 7...............................................
4 Installing Options 19...................................................
Powerware Hot Sync CAN Bridge Card 19.....................................................
5 Service and Support 27.................................................
TABLE OF CONTENTS
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
ii
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
1
Chapter 1 Introduction
A Tie Cabinet can be installed as a wall -mounted bypass or to provide support for a
parallel system for redundancy or extra capacity.
A wall-mounted bypass switch is used to bypass the UPS during maintenance or
servicing, providing wrap-around bypass for UPS service without shutting down the
load.
A parallel (load sharing) system provides more capacity than a single UPS and can
provide backup, depending on the load and configuration. In addition, when one UPS
is taken out of service for maintenance or is not operating properly, a redundant UPS
continues to supply uninterrupted power to the critical load. A parallel Powerware
®
Hot Sync
®
Controller Area Network (CAN) Bridge Card provides connectivity for
system metering and operational mode control. The parallel system consists of two to
four UPSs, each with a parallel CAN Bridge Card and a parallel cabinet.
Figure 1 shows the Powerware 9355 UPS.
Figure 1. The Powerware 9355 UPS
INTRODUCTION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
2
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
3
Chapter 2 Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and maintenance of
the UPS and batteries. Please read all instructions before operating the equipment and save this manual for
future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED
SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS.
WARNING
S This UPS contains its own energy source (batteries). The UPS output may carry live voltage even when
the UPS is not connected to an AC supply.
S To reduce the risk of fire or electric shock, install t his UPS in a temperature and humidity controlled,
indoor environment, free of conductive contaminants. Ambient temperature must not exceed 40°C
(104°F). Do not operate near water or excessive humidity (95% maximum).
S To reduce the risk of fire, connect only to a circuit provided with 125 amperes maximum branch circuit
overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70.
S Output overcurrent protection and disconnect switch must be provided by others.
CAUTION
S Batteries can present a risk of electrical shock or burn from high short circuit current. Observe proper
precautions. Servicing should be performed by qualified service personnel knowledgeable of batteries
and required precautions. Keep unauthorized personnel away from batteries.
S Proper disposal of batteries is required. Refer to your local codes for disposal requirements.
S Never dispose of batteries in a fire. Batteries may explode when exposed to flame.
SAFETY WARNINGS
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
4
Consignes de Sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute procédure
d’installation et de maintenance des batteries et de l’onduleur. Veuillez consulter entièrement ces
instructions avant de faire fonctionner l’équipement et conserver ce manuel afin de pouvoir vous y reporter
ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de réparation doit être
EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ. AUCUNE PIÈCE RÉPARABLE PAR
L’UTILISATEUR ne se trouve dans l’onduleur.
AVERTISSEMENT!
S Cette onduleur possède sa propre source d’alimentation (batteries). Il est possible que la sortie de
l’onduleur soit sous tension même lorsque l’onduleur n’est pas connectée à une alimentation CA.
S Pour réduire les risques d’incendie et de décharge électrique, installer l’onduleur uniquement à
l’intérieur, dans un lieu dépourvu de matériaux conducteurs, où la température et l’humidité ambiantes
sont contrôlées. La température ambiante ne doit pas dépasser 40 °C. Ne pas utiliser à proximité d’eau
ou dans une atmosphère excessivement humide (95 % maximum).
S Afin de réduire les risques d’incendie, n’effectuez le raccordement qu’avec un circuit muni d’une
protection de surintensité du circuit de dérivation maximum de 125 ampères conformément au Code
Électrique National (National Electrical Code) des États-Unis ANSI/NFPA 70.
S La protection de surintensité d e sortie ainsi que le sectionneur doivent être fournis par des tiers.
ATTENTION!
S Les batteries peuvent présenter un risque de choc électrique ou de brûlure provenant d’un courant de
court-circuit haute intensité. Observez les précautions appropriées. L’entretien doit être réalisé par du
personnel qualifié connaissant bien les batteries et les précautions nécessaires. N’autorisez aucun
personnel non qualifié à manipuler les batteries.
S Une mise au rebut réglementaire des batteries est obligatoire. Consulter les règlements en vigueur dans
votre localité.
S Ne jamais jeter les batteries au feu. L’exposition aux flammes risque de les faire exploser.
SAFETY WARNINGS
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
5
Advertencias de Seguridad
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el mantenimiento
del SIE y de las baterías. Por favor, lea todas las instrucciones antes de poner en funcionamiento el equipo y
guarde este manual para referencia en el futuro.
PELIGRO
Este SIE contiene VOLTAJES MORTALES. Todas las reparaciones y el servicio técnico deben ser efectuados
SOLAMENTE POR PERSONAL DE SERVICIO TÉCNICO AUTORIZADO. No hay NINGUNA PARTE QUE EL
USUARIO PUEDA REPARAR dentro del SIE.
ADVERTENCIA
S Este SIE contiene su propia fuente d e energía (baterías). La salida del SIE puede transportar voltaje
activo aun cuando el SIE no esté conectado con una fuente de CA.
S Para reducir el riesgo de incendio o de choque eléctrico, instale este SIE en un lugar cubierto, con
temperatura y humedad controladas, libre de contaminantes conductores. La temperatura ambiente no
debe exceder los 40°C. No trabaje cerca del agua o con humedad excesiva (95% máximo).
S Para reducir el riesgo de incendio, realice la conexión únicamente hacia un circuito que cuente con un
máximo de 125 amperios de protección contra sobrecorriente de circuito derivado, de acuerdo con el
Código Eléctrico Nacional, ANSI/NFPA 70.
S La protección contra sobrecorriente d e salida y el conmutador de desconexión debe suministrarse por
parte de terceros.
PRECAUCIÓN
S Las baterías pueden constituir un riesgo de descarga eléctrica o quemaduras por corriente alta de corto
circuito. Adopte las precauciones debidas. Personal calificado de servicio que conozca de baterías y esté
al tanto de las precauciones requeridas debe darle servicio al equipo. Mantenga al personal no
autorizado alejado de las baterías.
S Es necesario desechar las baterías de un modo adecuado. Consulte las normas locales para conocer los
requisitos pertinentes.
S Nunca deseche las baterías en el fuego. Las baterías pueden explotar si se las expone a la llama.
SAFETY WARNINGS
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
6
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
7
Chapter 3 Tie Cabinet Installation
The Powerware 9355 has the following power connections:
S 3-phase (L1, L2, and L3), neutral, and ground connection for rectifier/bypass input
S 3-phase (L1, L2, and L3), neutral, and ground connection for load output
The nominal input/output voltages are:
S 120/208 or 127/220 Vac
Output overcurrent protection and disconnect switch must be provided by others.
Figure 9 and Figure 11 beginning on page 15 show the oneline diagrams.
WARNING
Only qualified service personnel (such as a licensed electrician) should perform the UPS installation and
initial startup. Risk of electrical shock.
To hardwire the Tie Cabinet:
1. Verify that the electrical connections to the installation site have been properly
installed.
2. A wall-mounted, user -supplied, readily-accessible disconnection device must be
incorporated in the input wiring.
Compare the circuit breaker ratings to the ones in Table 1 on page 11.
NOTE To accommodate the feature of easy system expandability, it is recommended that initial installation
of the Powerware 9355 UPS contain wiring to support the maximum capacity of the UPS cabinet.
3. Switch off utility power to the distribution point where the Tie Cabinet and UPSs
will be connected. Be absolutely sure there is no power.
4. Determine your equipment’s grounding requirements according to your local
electrical code.
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
8
5. Remove the Tie Cabinet front cover (see Figure 2).
Figure 2. Tie Cabinet Front Cover
6. Remove the internal covers to gain access to the breakers (see Figure 3).
Figure 3. Internal Covers
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
9
7. Punch holes for the conduit (AC input, UPS output, load connection, and
maintenance bypass contact wires) using a Greenlee
®
punch or similar device.
8. Verify that the Tie Cabinet bypass breaker is in the OFF position (see Figure 4).
Figure 4. Tie Cabinet Bypass Breaker
9. Mount the Tie Cabinet to the wall and install the conduit.
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
10
10. From each UPS, remove the UPS front door.
11. Verify that the UPS input circuit breaker is in t he OFF position.
12. Verify that each UPS battery circuit breaker is in t he OFF position (see Figure 5).
13. If you ordered the UPS with the optional output circuit breaker, verify that the
output circuit breaker is in the OFF position.
14. Remove the UPS wiring access cover and retain.
Battery Circuit
Breaker
Wiring Access
Cover
Input Circuit
Breaker
Output Circuit
Breaker (optional)
Figure 5. UPS Front View
15. Remove the UPS conduit landing box from the rear panel and retain.
16. Punch two holes in the conduit landing box for the input and output conduit using
a Greenlee punch or similar device.
17. Route the wiring from the back of the UPS, through the wiring tray, to the front
of the UPS.
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
11
18. Hardwire the UPS input terminations.
See Table 1 for specifications and Figure 6 for a detailed view of the UPS
terminal block.
NOTE Input neutral must be wired for proper operation or the UPS will not start.
NOTE The Powerware 9355 UPS is shipped as a single-feed UPS and can be converted to a dual-feed UPS
in the field.
NOTE DO NOT overtighten the screws; be sure to use the specified tightening torque values shown in
Table 1.
Table 1. Terminal Block Wiring
20 kVA
Input Voltage
Wire
Function
Input Circuit
Breaker Size
L1, L2, L3, N
Wire Size
1
Ground
Wire Size
1
Tightening
Torque
Conduit Size
2, 3
(Number of Conduits)
208
Input
100A
1AWG 6AWG
2
0
0
”
C
d
i
(
1
)
220
p
100A
1AWG 6AWG
1
2
0
l
b
i
n
2.00” Conduit (1)
480
(with transformer) 45A
8AWG 10 AWG
1
2
0
l
b
i
n
(13.5 Nm)
1
0
0
”
C
d
i
(
1
)
600 (with transformer) 35A
8AWG 10 AWG
1.00” Conduit (1)
208
Output
1AWG 6AWG
220
p
1AWG 6AWG
120 lb in
(
1
3
5
N
m
)
2.00” Conduit (1)
480
(with transformer)
1AWG 6AWG
(
1
3
.
5
N
m
)
2
.
0
0
C
o
n
d
u
i
t
(
1
)
30 kVA
Input Voltage
Wire
Function
Input Circuit
Breaker Size
L1, L2, L3, N
Wire Size
1
Ground
Wire Size
1
Tightening
Torque
Conduit Size
2, 3
(Number of Conduits)
208
Input
125A
1/0 AWG 6AWG 2.00” Conduit (1)
220
p
125A
1/0 AWG 6AWG
1
2
0
l
b
i
n
2.00” Conduit (1)
480 (with transformer) 60A
6AWG 10 AWG
1
2
0
l
b
i
n
(13.5 Nm)
1.00” Conduit (1)
600 (with transformer) 50A
8AWG 10 AWG 1.00” Conduit (1)
208
Output
1/0 AWG 6AWG
220
p
1/0 AWG 6AWG
120 lb in
(
1
3
5
N
m
)
2.00” Conduit (1)
480
(with transformer)
1/0 AWG 6AWG
(
1
3
.
5
N
m
)
2
.
0
0
C
o
n
d
u
i
t
(
1
)
1
Use only 90°C-rated copper wire. Minimum wire size is based on 120/208 full load ratings applied to NEC Code Table 310-16. Code may require a larger
AWG size than shown in this table because of temperature, number of conductors in the conduit, or long service runs. Follow local requirements.
2
Per NEC article 300-20(a), all three-phase conductors must be run in the same conduit. Neutral and ground must be run in the same conduit as the
phase conductors.
3
Conduit is sized to accommodate one neutral conductor the same size as the phase conductor and one ground conductor. If two neutral conductors or
an oversized neutral conductor are to be installed, check the size of the conduit needed to accommodate the extra wire or size and use that conduit size
in place of the conduit size listed. Conduit sizes were chosen from NEC Table C1, type letters RHH, RHW, RHW-2, TW, THW, THHW, THW-2.
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
12
Jumpers
(remove three
wires for
dual-feed)
Input Terminal
Block
L1,L2,L3,N,N
Output Terminal
Block
L1,L2,L3,N,N
Remote DC
(battery)
DC +, DC –
Maintenance
Bypass Auxiliary
Contacts (TB4)
Ground
TB4
Figure 6. UPS Terminal Block
NOTE The two input neutral terminals are jumpered together; use either one of these terminals to make
the input neutral connection.
NOTE The two output neutral terminals are jumpered together; use either one of these terminals to make
the output neutral connection.
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
13
19. Hardwire the output terminations from the UPS t o the Tie Cabinet (see Figure 7).
20. Repeat Steps 11 through 19 for each UPS.
Neutral
Ground
Line 1
Line 2
Line 3
Figure 7. UPS Output to Tie Cabinet Wiring
TIE CABINET INSTALLATION
EATON Powerware
®
9355 Tie Cabinet (20/30 kVA) Installation Guide S 164201630 Rev A www.powerware.com
14
21. Hardwire the load to the Tie Cabinet (see Figure 8).
Neutral
Line 1
Ground
Line 2
Line 3
Maintenance Bypass
Wiring to UPS TB4
Figure 8. Load Connections
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Powerware Powerware 9355 Manuel utilisateur

Powerware
Marque
Powerware
Modèle
Powerware 9355
Catégorie
Alimentations sans interruption (UPS)
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents