Crestron ZUMNET-GATEWAY Guide d'installation

Marque: Crestron

Modèle: ZUMNET-GATEWAY

Catégorie: Passerelles / contrôleurs

Taper: Guide d'installation

ZUMNET-GATEWAY

Zūm™ Wireless Gateway

Installation Guide

Description

The Crestron

ZUMNET-GATEWAY is a 2-way RF wireless transceiver designed for use

with products that use the Zūm Net wireless communications protocol. A single

ZUMNET-GATEWAY works with the ZUM-FLOOR-HUB (not included) to provide central

monitoring, management, reporting, and control of lighting systems throughout the

enterprise.

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information. Use a QR reader application on your

mobile device to scan the QR image.

Pin 8 Pin 1

LAN PoE Pins

1. Data Pair 1

2. Data Pair 1

3. Data Pair 2

4. +Vdc

5. +Vdc

6. Data Pair 2

7. -Vdc

8. -Vdc

Pin 8 Pin 1

LAN Pins

1. Data Pair 1

2. Data Pair 1

3. Data Pair 2

4. No Connection

5. No Connection

6. Data Pair 2

7. No Connection

8. No Connection

To supply power using a Crestron PoE injector (sold separately), do the following.

1. Attach the supplied ac power cord to the IEC 320 connector on the PoE (Power over

Ethernet) injector.

2. Use a CAT5 cable to connect the LAN port of the PoE injector to the LAN.

3. Use a CAT5 cable to connect the LAN POE port of the PoE injector to the LAN PoE

input port of the ZUMNET-GATEWAY.

4. Insert the other end of the power cord into an active ac outlet.

NOTE: In the listing of LAN PoE and LAN pins in the following image, arrows denote

internal pin connections.

LAN PoE and LAN Pin Assignments

USB

Power

supply

input

LAN

PoE

input

For

included

antenna

Make Connections

Make the necessary connections as called out in the illustrations that follow. Apply power

after all connections have been made.

NOTE: When making connections to the ZUMNET-GATEWAY, use Crestron power

supplies for Crestron equipment.

NOTE: The antenna must be attached directly to the antenna connector. It can be

extended with an optional ANT-EXT-10 Antenna Extender (sold separately).

Installation

NOTE: Observe the following:

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• A qualied electrician must install this product.

Mount the ZUMNET-GATEWAY onto a DIN rail or onto a vertical at surface. It can also be

placed onto a horizontal at surface.

NOTE

: Do not install this gateway within 15 feet (4.6 meters) of other Zūm Net or

inNET EX

gateways.

NOTE: The ZUMNET-GATEWAY can also be rack mounted. For rack mount installation,

refer to the RMK-IFE-1U Installation Guide (Doc. 7627) at www.crestron.com/manuals.

Vertical Flat Surface Mounting

1. Attach the bracket to the wall (wall mount screws not included).

2. Attach the ZUMNET-GATEWAY to the bracket by snapping it into place.

3. Insert the supplied screws through the side of the bracket and secure the gateway.

DIN Rail Mounting

1. Attach the bracket to the DIN rail by snapping it into place.

2. Attach the ZUMNET-GATEWAY to the bracket by snapping it into place.

3. Insert the supplied screws through the side of the bracket and secure the gateway.

NOTE: When mounting to a DIN rail, use the screw holes only on the side of the

bracket when securing the gateway to the bracket. Using the screw holes on the

back of the bracket to secure the gateway to the bracket will prevent removal of the

device from the DIN rail.

Select the Mounting Location

For optimum performance when installing multiple ZUMNET-GATEWAYs near each other:

• Do not place multiple gateways on the same channel.

• Place gateways at least 15 feet (4.6 meters) apart.

For optimum performance when installing a ZUMNET-GATEWAY:

• Place gateways at least 15 feet (4.6 meters) from the nearest Wi-Fi

access point.

• Place gateways at least 6 feet (1.8 meters) from the nearest Bluetooth

device.

For more information, refer to Installation and Setup of Crestron RF Products (Doc. 6689)

at www.crestron.com/manuals.

This product is Listed to applicable UL

Standards and requirements by Underwriters Laboratories

Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference and (2) this device must accept any interference

received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to

the following two conditions: (1) this device may not cause interference and (2) this device must

accept any interference, including interference that may cause undesired operation of the device radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Industrie Canada (IC) Déclaration de conformité

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

Crestron Electronics, Inc. Installation Guide - DOC. 7936C

15 Volvo Drive, Rockleigh, NJ 07647 (2048522)

Tel: 888.CRESTRON 06.18

Fax: 201.767.7576 Specications subject to

www.crestron.com change without notice.

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit

pasproduire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner

avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie

Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres

utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée

équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication

satisfaisante.

To satisfy RF exposure requirements, this device and its antenna must operate with a separation

distance of at least 20 centimeters from all persona and must not be colocated in conjunction with any

other antenna or transmitter.

The product warranty can be found at www.crestron.com/warranty.

The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specic information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, inNET EX, and Zūm are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other countries. Bluetooth is either a trademark

or registered trademark of Bluetooth SIG, Inc. in the United States and/or other countries. UL and the

UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the

United States and/or other countries. Wi-Fi is either a trademark or registered trademark of Wi-Fi

Alliance in the United States and/or other countries. Other trademarks, registered trademarks, and

trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Crestron disclaims any proprietary interest in the marks and names of others.

Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Specications

NOTE: “Zūm Net” refers to the wireless mesh network that connects one or more rooms with a Zūm Floor Hub, and consists of one Zūm Net Wireless Gateway and one or more Zūm

Network Bridges. Each Zūm Network Bridge functions as a routing node, which relays the signals it receives on to any other Zūm Net devices within range. This effectively extends the

total range of the network and provides multiple redundant signal paths for extra reliability. A maximum of six “hops” across routing nodes is allowed, although a maximum of three is

recommended. Up to 100 Zūm Net devices are permitted per gateway, although best practices suggest a limit of 50. Refer to the “Installation and Setup of Crestron RF Products” Best

Practices guide (Doc. 6689) at www.crestron.com/manuals for more information.

NOTE: Do not stack multiple gateways.

SPECIFICATION DETAILS

Supported Devices

Zūm Net Devices

Maximum Devices Allowed

Supports Crestron Zūm Net wireless devices only

Supports

up to 100 Zūm Network Bridges per Zūm Net Gateway

Wireless Communications

RF Transceiver

Range