Crestron DSP-1282 Information produit

Taper
Information produit

Ce manuel convient également à

DSP-860, DSP-1280, DSP-1281, DSP-1282, DSP-1283
Crestron Avia™ Digital Signal Processor
Product Information - 8734A
(2055754)
04.20
Getting Started
Scan the QR code to view the Quick Start Guide.
www.crestron.com/docs/7647
For additional information on the DSP-860, visit
www.crestron.com/model/6507123.
For additional information on the DSP-1280, visit
www.crestron.com/model/6506917.
For additional information on the DSP-1281, visit
www.crestron.com/model/6506918.
For additional information on the DSP-1282, visit
www.crestron.com/model/6506919.
For additional information on the DSP-1283, visit
www.crestron.com/model/6506920.
Certification and Compliance
As of the date of manufacture, the product has
been tested and found to comply with
specifications for CE marking.
This product is Listed to applicable UL® Standards
and requirements tested by Underwriters
Laboratories Inc.
Ce produit est homologué selon les normes et les
exigences UL applicables par Underwriters
Laboratories Inc.
Federal Communications Commission (FCC)
Compliance Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following conditions:
(1) This device may not cause harmful interference
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment
and receiver.
l Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
l Consult the dealer or an experienced radio/TV
technician for help.
FCC Compliance Information (DSP-1283 and DSP-
1282 only)
l Consult the dealer or an experienced radio/TV
technician for help.
l This equipment complies with Part 68 of Federal
Communications Commission (FCC) rules and
requirements adopted by Americas Carriers
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7656
www.crestron.com
Product Information - Doc. 8734A
(2055754)
04/21/20
Telecommunications Association (ACTA). Each
registered interface has a label that contains,
among other information, a product identifier in
the format US: CTUMM00BDMPS3300AEC. If
requested, provide this information to the
telephone company.
l If this equipment causes harm to the telephone
network, the telephone company may
temporarily discontinue service. If possible,
advance notification is given; otherwise,
notification is given as soon as possible. The
telephone company will advise the customer of
the right to file a complaint with the FCC.
l The telephone company may make changes in
its facilities, equipment, operations, or
procedures that could affect the proper
operation of this equipment. Advance
notification and the opportunity to maintain
uninterrupted service are given.
l If experiencing difficulty with this equipment,
please contact manufacturer for repair and
warranty information. The telephone company
may require this equipment to be disconnected
from the network until the problem is corrected,
or it is certain the equipment is not
malfunctioning.
l This unit contains no user-serviceable parts.
l This equipment is designed to connect to the
telephone network or premises wiring using an
FCC-compatible modular jack, which is
compliant with Part 68 and requirements
adopted by ACTA.
l The ringer equivalence number (REN) is useful in
determining the quantity of devices you may
connect to your telephone line and still have all of
those devices ring when your number is called. In
most areas, the sum of the RENs of all devices
should not exceed five. To be certain of the
number of devices you may connect to your line
as determined by the REN, call your telephone
company to determine the maximum REN for
your calling area.
l This equipment may not be used on coin service
provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact
your state public utility commission or
corporation commission for information.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
REN IC 0.1 (DSP-1283 and DSP-1282 only)
This product meets the applicable Industry Canada
technical specifications. The Ringer Equivalence
Number (REN) is an indication of the maximum
number of devices allowed to be connected to a
telephone interface. The termination of an interface
may consist of any combination of devices subject
only to the requirement that the sum of the RENs of
all the devices not exceed five.
Le présent matériel est conforme aux specifications
techniques applicables d’Industrie Canada. L’indice
d’équivalence de la sonnerie (IES) sert à indiquer le
nombre maximal de terminaux qui peuvent être
raccordés à une interface téléphonique. La
terminaison dune interface peut consister en une
combinaison quelconque de dispositifs, à la seule
condition que la somme dindices déquivalence de
la sonnerie de tous les dispositifs n’excède pas cinq.
ACTA Compliance Information
REN US 0.0B (DSP-1283 and DSP-1282 only)
The Ringer Equivalence Number (REN) indicates the
maximum number of devices allowed to be
connected to a telephone interface. The
termination of an interface may consist of any
combination of devices subject only to the
requirement that the sum of the RENs of all the
devices not exceed five.
Legal
The product warranty can be found at
www.crestron.com/warranty.
The specific patents that cover Crestron products
are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source
software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, and Avia are either
trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other
countries. UL and the UL logo are either
trademarks or registered trademarks of
Underwriters Laboratories, Inc. in the United States
and/or other countries. Other trademarks,
registered trademarks, and trade names may be
used in this document to refer to either the entities
claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not
responsible for errors in typography or
photography.
©2020 Crestron Electronics, Inc.
  • Page 1 1
  • Page 2 2

Crestron DSP-1282 Information produit

Taper
Information produit
Ce manuel convient également à

dans d''autres langues