JVC CS-AW7020 Manuel utilisateur

INSTRUCTION MANUAL

MANUEL D'INSTRUCTIONS

MANUAL DE INSTRUCCIONES

CS-AW7020 CS-AW7040

CS-AW7220 CS-AW7240

CS-AW7020 CS-AW7220

CS-AW7040 CS-AW7240

For Customer Use:

Enter below the Model No, and Serial

No, which is located either on the rear

or bottom of the speaker unit. Retain

this information for future reference.

Model No.

Serial No.

LVT1743-001A

SUBWOOFER

CAISSON DE GRAVE

ENGLISH

FRANÇAISESPAŃOL

Thank you for purchasing the ARSENAL Car Stereo Speaker. These Speakers can be

mounted in the trunk of your vehicle. For the secure installation and perfect operation

of your speakers, please read the following carefully.

Parts

For proper installation and use

1.Before connecting the speakers to the amplifier, confirm that the power has been

turned off. The click noise generated by the connection if the power is on may

damage the speakers.

2.The amplifier and speakers should be connected between corresponding terminals,

i.e. left to left, and right to right, as well as "+" to "+", and "–" to "–". Connection with

reversed polarity will degrade the quality of stereo reproduction.

3.Do not subject the speakers to excessive input. The power handling capacity of the

CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 is 600 watts (R.M.S. MUSIC

POWER). Any excessive input may damage the speakers.

4.The CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 has an impedance of 2Ω

,4Ω,8Ω. Make sure that the output impedance of the amplifier's speaker terminal is

rated at 2Ω,4Ω,8Ω.

5.When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not

apply thinner or solvent.

6.Be sure to carefully follow the instructions for:

Cable Connections

Fuse Replacement

Switching the Impedance Selector

Subwoofer Mounting and Smart Trim Ring Installation

Consult Page 19 of this Instruction Manual for details on these procedures.

1. Grille

5. Hexagon socket

screw keys

4. Fuse (10A) x 2

3. Jump2. Screw x 10

- 2 -

ENGLISH

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

1 Mono Amplifier

1 Subwoofer

Jumper set to Series

8Ω(4Ω+4Ω) Load

4Ω

2Ω

4Ω

4Ω4Ω

8Ω

4Ω

Mono

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

Stereo

Mono

4Ω

8Ω 8Ω

4Ω

4Ω 4Ω 4Ω

Mono

4Ω

8Ω

2.6Ω

4Ω

Mono

4Ω

8Ω

2Ω

4Ω

8Ω

4Ω

8Ω

4Ω

8Ω

4Ω

8Ω

4Ω 4Ω

8Ω

4Ω

Mono

1 Mono Amplifier

1 Subwoofer

Jumper set to Parallel

8Ω(4Ω+4Ω) Load

4Ω 2-Chan

1 2ch Amplifier

1 Subwoofer

Jumper is Removed

4Ω Load

1 Mono Amplifier

2 Subwoofers

Jumper set to Series

Subwoofers wired in Parallel

4Ω Load

1 Mono Amplifier

3 Subwoofers

Jumper set to Series

Subwoofers wired in Parallel

2.6Ω Load

1 Mono Amplifier

4 Subwoofers

Jumper set to Series

Subwoofers wired in Parallel

2Ω Load

Dual 4 Ω Application Diagrams

- 3 -

Bi-Amp Configuration 2 Mono Amplifiers

1 Subwoofer Jumper is Removed 4Ω Load

ENGLISH

*JUMPER is Removed *JUMPER is Removed

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

1 Mono Amplifier

1 Subwoofer

Jumper set to Series

4Ω(2Ω+2Ω) Load

2Ω

1Ω

2Ω

2Ω2Ω

4Ω

2Ω

Mono

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

Stereo

Mono

2Ω

4Ω 4Ω

2Ω

2Ω 2Ω 2Ω

Mono

2Ω

4Ω

1.3Ω

2Ω

Mono

2Ω

4Ω

1Ω

2Ω

4Ω

2Ω

4Ω

2Ω

4Ω

2Ω

4Ω

2Ω 2Ω

4Ω

2Ω

Mono

1 Mono Amplifier

1 Subwoofer

Jumper set to Parallel

4Ω(2Ω+2Ω) Load

2Ω 2-Chan

1 2ch Amplifier

1 Subwoofer

Jumper is Removed

2Ω Load

1 Mono Amplifier

2 Subwoofers

Jumper set to Series

Subwoofers wired in Parallel

2Ω Load

1 Mono Amplifier

3 Subwoofers

Jumper set to Series

Subwoofers wired in Parallel

1.3Ω Load

1 Mono Amplifier

4 Subwoofers

Jumper set to Series

Subwoofers wired in Parallel

1Ω Load

Dual 2 Ω Application Diagrams

- 4 -

Bi-Amp Configuration 2 Mono Amplifiers

1 Subwoofer Jumper is Removed 2Ω Load

ENGLISH

*JUMPER is Removed *JUMPER is Removed

C

B

A

G

H

I

B

A

CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240

A 15-13/32 inch (391.7 mm)

16-13/32 inch (417.1 mm)

B 15-13/32 inch (391.7 mm)

16-13/32 inch (417.1 mm)

C

11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)

D

9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm)

E

9-23/32 inch (247 mm) 11-10/32 inch (295 mm)

F

G

4/32 inch (3 mm) 4/32 inch (3 mm)

1.57 ft

3

(0.045 m

3

) 2.17 ft

3

(0.062 m

3

)

CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240

A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)

B

18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)

C

13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)

D

9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm)

E

9-23/32 inch (247 mm) 11-10/32 inch (295 mm)

F

4/32 inch (3 mm) 4/32 inch (3 mm)

G

1 inch (25.4 mm) 1 inch (25.4 mm)

H

13 inch (330.2 mm) 14 inch (355.6 mm)

I

J

13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)

1.85 ft

3

(0.052 m

3

) 2.54 ft

3

(0.072 m

3

)

To install the ported enclosure

When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also

recommended for the enclosure materials.

To install the sealed enclosure

When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also

recommended for the enclosure materials.

Front & Rear Bae Boards (x 2)

Left & Right Sides (x 2)

Top & Bottom Sides (x 2)

* Screw: Dia. 4mm x 50mm (x 8) (supplied)

Mounting Hole

Dimension

Front & Rear Bae Boards (x 2)

Left & Right Sides (x 2)

Top & Bottom Sides (x 2)

* Screw: Dia. 4mm x 50mm (x 8) (supplied)

Mounting Hole

Dimension

- 5-

ENGLISH

J : Internal Volume

G : Internal Volume

- 6 -

ENGLISH

Nominal Impedance (Ω)

SPL : Sound pressure levelSPL (dB,1W/1M)

Displacement (Liter)

Hole Cutout Diameter (inch)

(mm)

Mounting Depth (inch)

(mm)

Re (Ω) Re : DC voice coil resistance

BL (T.M)

BL : Product of Flux density and

Effective Voicecoil-wire length

Vas (Liter)

Vas : Volume of air equal to the driver

compliance

Vas (CuFt)

Me : Effective massMe (g)

D (mm) D : Effective cone diameter

Fs : Driver free air resonanceFs (Hz)

Qms

Qms : Q of driver at Fs considering

only non-electrical resistance

Qes

Qes : Q of driver at Fs considering

only electrical resistance

Qts : Total Q of driver at FsQts

Pe [max.] (W)

Pe[max.] : Maximum continuous input

power

Xmax.(mm)

Xmax. : Maximum effective voicecoil

travel without distortion

Freq.Responce (Hz)

Magnet Mass (oz)

(g)

Voice Coil(Aluminum)Dia.(inch)

(mm)

Hvc (mm) Hvc : Voice coil Height

Hag (mm) Hag : Gap Height

NOTESParameters

parallel

83.49 dB

series seriesparallel

0.98 Ω 3.83 Ω 7.6 Ω1.92 Ω

6.85 13.75 17.218.68

17.08 L 16.98 L 18.28 L18.08 L

39.6 Hz 39.5 Hz 41.8 Hz41.7 Hz

10.261 10.282 9.1699.021

0.756 0.74 0.8240.83

0.704 0.691 0.7560.76

145.986 g 147.109 g 122.443 g124.084 g

0.6 ft

3

0.599 ft

3

0.65 ft

3

0.64 ft

3

83.54 dB 84.12 dB84.02 dB

25 ~500 Hz

6 - 14/32 inch

( 163.5 mm )

CS-AW7040CS-AW7020

2Ω + 2Ω 4Ω + 4Ω

Dia. 2 - 5/32 inch

54.5 mm

39.9 mm

10 mm

39.6 mm

Dia. 2 - 4/32 inch

53.59 mm

14.95 mm 14.8 mm

65.4 oz

( 1854.1 g )

600 W

Dia. 202 mm

Dia. 9 - 6/32 inch

( 233 mm )

0.123 ft

3

Nominal Impedance (Ω)

SPL : Sound pressure levelSPL (dB,1W/1M)

Displacement (Liter)

Hole Cutout Diameter (inch)

(mm)

Mounting Depth (inch)

(mm)

Re (Ω) Re : DC voice coil resistance

BL (T.M)

BL : Product of Flux density and

Effective Voicecoil-wire length

Vas (Liter)

Vas : Volume of air equal to the driver

compliance

Vas (CuFt)

Me : Effective massMe (g)

D (cm) D : Effective cone diameter

Fs : Driver free air resonanceFs (Hz)

Qms

Qms : Q of driver at Fs considering

only non-electrical resistance

Qes

Qes : Q of driver at Fs considering

only electrical resistance

Qts : Total Q of driver at FsQts

Pe [max.] (W)

Pe[max.] : Maximum continuous input

power

Xmax.(mm)

Xmax. : Maximum effective voicecoil

travel without distortion

Freq.Responce (Hz)

Magnet Mass (oz)

(g)

Voice Coil(Aluminum)Dia.(inch)

(mm)

Hvc (mm) Hvc : Voice coil Height

Hag (mm) Hag : Gap Height

NOTESParameters

parallel

85.13 dB

series seriesparallel

0.98 Ω 3.84 Ω 7.61 Ω1.94 Ω

6.84 13.72 19.149.56

38.7 L 38.76 L 35.05 L35.23 L

34.6 Hz 34.5 Hz 38 Hz37.9 Hz

10.277 10.089 9.0148.931

0.786 0.765 0.7810.794

0.73 0.711 0.7190.73

171.854 g 172.934 g 157.336 g157.028 g

1.37 ft

3

1.37 ft

3

1.24 ft

3

1.24 ft

3

85.2 dB 85.65 dB85.87 dB

23 ~500 Hz

7 - 6/32 inch

( 182.5 mm )

CS-AW7240CS-AW7220

2Ω + 2Ω 4Ω + 4Ω

Dia. 2 - 5/32 inch

( 54.5 mm )

39.9 mm

10 mm

39.6 mm

Dia. 2 - 4/32 inch

( 53.59 mm )

14.95 mm 14.8 mm

86.2 oz

( 2443.7 g )

600 W

Dia. 246 mm

Dia. 10 - 29/32 inch

( 277 mm )

0.18 ft

3

Nous vous remercions pour I'achat d'un haut-parleur auto stéréo de ARSENAL dans

le coffre de votre véhicule. Pour un montage sûr et un fonctionnement parfait de ce

haut-parleur, il est conseillé de lire attentivement ce qui suit.

Montage et utilisation corrects

1.Vérifier que l'alimentation est coupée avant de raccorder les haut-parleurs à

l'amplificateur. Les craquements produits par le raccordement lors que l'alimentation

est fournie peuvent endomma ger les haut-parleurs.

2.Raccorder les bornes correspondantes de l’amplificateur et les haut-parleurs,

c'est-à-dire, gauche à gauche, droit à droite, de même que “+” à “+” et “–” à “–”. Un

raccordement effectué en inversant les polarités réduira la qualité de la reproduction

sonore stéréo-phonique.

3.Ne pas appliquer un niveau d'entrée excessif aux haut-parleurs. La puissance

d'entrée admissible pour les haut-parleurs

CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 est de 600 watts (puissance

musicale R.M.S.). Tout signal d'entrée excessif risque de les endommager.

4.Les haut-parleurs CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 ont une

impédance de 2Ω,4Ω,8Ω. ll faut par conséquent s'assurer que l'impédance de sortie

aux bornes de haut-parleur de l'amplificateur soit aussi de 2Ω,4Ω,8Ω.

5.Nettoyer le haut-parleur en le frottant légèrement à l'aide d'un chiffon doux. Ne

jamais utiliser de solvants ni de détergents.

6.Veuillez suivre attentivement les instructions suivantes pour:

Connections de Câble

Remplacement de Fusible

Changement de la Sélection d'Impédance

Montage du Subwoofer et Installation Pratique de la Moulure de Finition

Consultez la Page 19 de ce Manuel d'Instruction pour les détails de cesprocédures.

Parts

1. Grille

5. Hexagon socket

screw keys

4. Fuse (10A) x 2

3. Jump2. Screw x 10

- 7 -

FRANÇAIS

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

1 amplificateur mono

1 (un) caisson de basse

Cavalier branché en Série

Impédance de charge de

8Ω(4Ω+4Ω)

4Ω

2Ω

4Ω4Ω

8Ω

4Ω

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

Stereo

Mono

4Ω

8Ω 8Ω

4Ω

4Ω 4Ω 4Ω

Mono

4Ω

8Ω

2.6Ω

4Ω

Mono

4Ω

8Ω

2Ω

4Ω

8Ω

4Ω

8Ω

4Ω

8Ω

4Ω

8Ω

4Ω 4Ω

8Ω

4Ω

Mono

1 amplificateur mono

1 (un) caisson de basse

Cavalier branché en Parallèle

Impédance de charge de

8Ω(4Ω+4Ω)

4Ω 2-Chan

1 amplificateur mono

1 (un) caisson de basse

Cavalier branché en Parallèle

Impédance de charge de 8Ω(4Ω+4Ω)

1 amplificateur mono

2 (deux) caissons de basse

Cavalier branché en Série

Subwoofers wired in Parallel

Impédance de charge de 4Ω

1 amplificateur mono

3 (trois) caissons de basse

Cavalier branché en Série

Subwoofers wired in Parallel

Impédance de charge de 2.6Ω

1 amplificateur mono

4 (quatre) caissons de basse

Cavalier branché en Série

Subwoofers wired in Parallel

Impédance de charge de 2Ω

Diagrammes d’application duale 4Ω

- 8 -

Configuration en double amplification

2 amplificateurs mono

1 (un) caisson de basse Cavalier débranché

Impédance de charge de 4Ω

FRANÇAIS

*JUMPER is Removed

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

4Ω

Mono

*JUMPER is Removed

1 amplificateur mono

1 (un) caisson de basse

Cavalier branché en Série

Impédance de charge de

4Ω(2Ω+2Ω)

1 amplificateur mono

1 (un) caisson de basse

Cavalier branché en Parallèle

Impédance de charge de

4Ω(2Ω+2Ω)

1 amplificateur mono

1 (un) caisson de basse

Cavalier branché en Parallèle

Impédance de charge de 4Ω(2Ω+2Ω)

1 amplificateur mono

2 (deux) caissons de basse

Cavalier branché en Série

Subwoofers wired in Parallel

Impédance de charge de 2Ω

1 amplificateur mono

3 (trois) caissons de basse

Cavalier branché en Série

Subwoofers wired in Parallel

Impédance de charge de 1.3Ω

1 amplificateur mono

4 (quatre) caissons de basse

Cavalier branché en Série

Subwoofers wired in Parallel

Impédance de charge de 1Ω

Diagrammes d’application duale 2Ω

- 9 -

Configuration en double amplification

2 amplificateurs mono

1 (un) caisson de basse Cavalier débranché

Impédance de charge de 2Ω

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

2Ω

1Ω

2Ω2Ω

4Ω

2Ω

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

Stereo

Mono

2Ω

4Ω 4Ω

2Ω

2Ω 2Ω 2Ω

Mono

2Ω

4Ω

1.3Ω

2Ω

Mono

2Ω

4Ω

1Ω

2Ω

4Ω

2Ω

4Ω

2Ω

4Ω

2Ω

4Ω

2Ω 2Ω

4Ω

2Ω

Mono

2Ω 2-Chan

FRANÇAIS

*JUMPER is Removed

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

2Ω

Mono

*JUMPER is Removed

C

B

A

G

H

I

B

A

CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240

A 15-13/32 inch (391.7 mm)

16-13/32 inch (417.1 mm)

B 15-13/32 inch (391.7 mm)

16-13/32 inch (417.1 mm)

C

11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)

D

9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm)

E

9-23/32 inch (247 mm) 11-10/32 inch (295 mm)

F

G

4/32 inch (3 mm) 4/32 inch (3 mm)

1.57 ft

3

(0.045 m

3

) 2.17 ft

3

(0.062 m

3

)

CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240

A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)

B

18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)

C

13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)

D

9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm)

E

9-23/32 inch (247 mm) 11-10/32 inch (295 mm)

F

4/32 inch (3 mm) 4/32 inch (3 mm)

G

1 inch (25.4 mm) 1 inch (25.4 mm)

H

13 inch (330.2 mm) 14 inch (355.6 mm)

I

J

13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)

1.85 ft

3

(0.052 m

3

) 2.54 ft

3

(0.072 m

3

)

Écrans acoustiques avant et arrière (x 2)

Faces gauche et

droite (x 2)

Faces supérieure et

inférieure (x 2)

* Vis: Dia. 4mm x 50mm (x 8) (fournis)

Faces gauche

et droite (x 2)

Pour installer l’enceinte hermétique

Si le haut-parleur ne peut pas être xé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des

spécications données dans le tableau ci-dessous; le

MDF—20 mm (3/4 pouce) est recommandé pour le matériau

de l’enceinte.

Écrans acoustiques avant et arrière (x 2)

Faces gauche et

droite (x 2)

Faces supérieure et

inférieure (x 2)

* Vis: Dia. 4mm x 50mm (x 8) (fournis)

Faces gauche

et droite (x 2)

Pour installer l’enceinte hermétique

Si le haut-parleur ne peut pas être xé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des

spécications données dans le tableau ci-dessous; le

MDF—20 mm (3/4 pouce) est recommandé pour le matériau

de l’enceinte.

- 10 -

FRANÇAIS

J : Volume interne

G : Volume interne

- 11 -

FRANÇAIS

Impédance nominale (Ω)

SPL (dB,1W/1M) SPL : Niveau de pression sonore

Déplacement (Liter)

Diamètre du tuou de découpe (

pouces)

(mm)

Profondeur de montage (pouces)

(mm)

Re (Ω)

Re : Résistance de la bobine mobile

en CC

BL (T.M)

BL : Produit de la densité de flux et de l

a longueur efficace de fil de la bobine

mobile

Vas (Iitre)

Vas : Volume d'air égal à la conformité

de l'excitateur

Vas (CuFt)

Me : Masse effectiveMe (g)

D (mm) D : Diamètre effectif du cône

Fs (Hz)

Fs : Résonance à l'air libre de

l'excitateur

Qms

Qes

Qts : Q total de l'excitateur à FsQts

Pe [max.] (W)

Pe[max.] : Puissance d'entrée

continue maximum

Xmax. (mm)

Qms : Q de l'excitateur à Fs considérant

uniquement la résistance non-électrique

Qes : Q de l'excitateur à Fs considérant

uniquement la résistance électrique

Xmax. : Déplacement effectif maximum

de la bobine mobile sans distorsion

Réponse en fréquence (Hz)

Masse de l’aimant (once)

(g)

Diamètre de la bobine mobile (

pouces)

(mm)

Hvc (mm) Hvc : Hauteur de la bobine mobile

Hag (mm) Hvc : Hauteur de la bobine mobile

Paramètres

REMARQUES

parallel

85.13 dB

series seriesparallel

0.98 Ω 3.84 Ω 7.61 Ω1.94 Ω

6.84 13.72 19.149.56

38.7 L 38.76 L 35.05 L35.23 L

34.6 Hz 34.5 Hz 38 Hz37.9 Hz

10.277 10.089 9.0148.931

0.786 0.765 0.7810.794

0.73 0.711 0.7190.73

171.854 g 172.934 g 157.336 g157.028 g

1.37 ft

3

1.37 ft

3

1.24 ft

3

1.24 ft

3

85.2 dB 85.65 dB85.87 dB

23 ~500 Hz

7 - 6/32 inch

( 182.5 mm )

CS-AW7240CS-AW7220

2Ω + 2Ω 4Ω + 4Ω

Dia. 2 - 5/32 inch

( 54.5 mm )

39.9 mm

10 mm

39.6 mm

Dia. 2 - 4/32 inch

( 53.59 mm )

14.95 mm 14.8 mm

86.2 oz

( 2443.7 g )

600 W

Dia. 246 mm

Dia. 10 - 29/32 inch

( 277 mm )

0.18 ft

3

Impédance nominale (Ω)

SPL (dB,1W/1M) SPL : Niveau de pression sonore

Déplacement (Liter)

Diamètre du tuou de découpe (

pouces)

(mm)

Profondeur de montage (pouces)

(mm)

Re (Ω)

Re : Résistance de la bobine mobile

en CC

BL (T.M)

BL : Produit de la densité de flux et de

la longueur efficace de fil de la bobine

mobile

Vas (Iitre)

Vas : Volume d'air égal à la conformité

de l'excitateur

Vas (CuFt)

Me : Masse effectiveMe (g)

D (mm) D : Diamètre effectif du cône

Fs (Hz)

Fs : Résonance à l'air libre de

l'excitateur

Qms

Qes

Qts : Q total de l'excitateur à FsQts

Pe [max.] (W)

Pe[max.] : Puissance d'entrée

continue maximum

Xmax. (mm)

Qms : Q de l'excitateur à Fs considérant

uniquement la résistance non-électrique

Qes : Q de l'excitateur à Fs considérant

uniquement la résistance électrique

Xmax. : Déplacement effectif maximum

de la bobine mobile sans distorsion

Réponse en fréquence (Hz)

Masse de l’aimant (once)

(g)

Diamètre de la bobine mobile (

pouces)

(mm)

Hvc (mm) Hvc : Hauteur de la bobine mobile

Hag (mm) Hvc : Hauteur de la bobine mobile

Paramètres

REMARQUES

parallel

83.49 dB

series seriesparallel

0.98 Ω 3.83 Ω 7.6 Ω1.92 Ω

6.85 13.75 17.218.68

17.08 L 16.98 L 18.28 L18.08 L

39.6 Hz 39.5 Hz 41.8 Hz41.7 Hz

10.261 10.282 9.1699.021

0.756 0.74 0.8240.83

0.704 0.691 0.7560.76

145.986 g 147.109 g 122.443 g124.084 g

0.6 ft

3

0.599 ft

3

0.65 ft

3

0.64 ft

3

83.54 dB 84.12 dB84.02 dB

25 ~500 Hz

6 - 14/32 inch

( 163.5 mm )

CS-AW7040CS-AW7020

2Ω + 2Ω 4Ω + 4Ω

Dia. 2 - 5/32 inch

( 54.5 mm )

39.9 mm

10 mm

39.6 mm

Dia. 2 - 4/32 inch

( 53.59 mm )

14.95 mm 14.8 mm

65.4 oz

( 1854.1 g )

600 W

Dia. 202 mm

Dia. 9 - 6/32 inch

( 233 mm )

0.123 ft

3

Le agradecemos la adquisición del Altavoz Estereofónico para Automóvil de

ARSENAL. Para efectuar una instalación segura y para que el altavoz funcione

correctamente, lea detenidamente las siguientes instrucciones.

Parts

1. Grille

5. Hexagon socket

screw keys

4. Fuse (10A) x 2

3. Jump2. Screw x 10

- 12 -

Instalación y uso correctos

1.Antes de conectar los altavoces con el amplificador, confirme que esté cortada la

alimentación eléctrica. El ruido producido al realizar la conexión con la alimentación

conectada puede causar daños en los altavoces.

2.Deben conectares los terminales correspondientes del amplificador y de los

altavoces, es decir izquierdo a izquierdo y derecho a derecho,asi co mo “+” a “+” y

“–” a “–”. Si las polaridades se co nectan inversamente, la reproducción este

reofónica se deteriorará.

3.No someta los altavoces a una entrada excesiva. La capacidad máxima de los

CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 es de 600 votios (POTENCIA

MUSICAL R.M.S.). Una entra da excesiva dañará los altavoces.

4.Los CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 tienen 2Ω,4Ω,8Ω de

impedancia. Asegúrese de que la impe dancia de salida del terminal para altavoces

de amplificador sea de 2Ω, 4Ω,8Ω.

5.Cuando limpie los altavoces, utilice un paño suave y frote la superficie con cuidado.

No aplique solventes ni diluyentes.

6.Asegurese de seguir cuidadosamente las instrucciones para:

Conecciones de Cable

Reemplazo de fucible

Cambiando el Selector de Resistencia

Instalar el subwoofer y la moldura del anillo

Consulte la Page 19 de este Manual de Instrucciones para los detalles de estos

procedimientos.

ESPAŃOL

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

1 amplificador monofónico

1(un) bajo

Puente fijado en serie

Carga a 8Ω(4Ω+4Ω)

4Ω

2Ω

4Ω

4Ω4Ω

8Ω

4Ω

Mono

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

Stereo

Mono

4Ω

8Ω 8Ω

4Ω

4Ω 4Ω 4Ω

Mono

4Ω

8Ω

2.6Ω

4Ω

Mono

4Ω

8Ω

2Ω

4Ω

8Ω

4Ω

8Ω

4Ω

8Ω

4Ω

8Ω

4Ω 4Ω

8Ω

4Ω

Mono

1 amplificador monofónico

1(un) bajo

Puente fijado en Paralelo

Carga a 8Ω(4Ω+4Ω)

4Ω 2-Chan

Amplificador 1,2 ch

1(un) bajo

Se quita el puente

Carga a 4Ω

1 amplificador monofónico

2 (Dos) bajos

Puente fijado en serie

Subwoofers wired in Parallel

Carga a 4Ω

1 amplificador monofónico

3 (Tres) bajos

Puente fijado en serie

Subwoofers wired in Parallel

Carga a 2.6Ω

1 amplificador monofónico

4 (Cuatro) bajos

Puente fijado en serie

Subwoofers wired in Parallel

Carga a 2Ω

Diagramas de Aplicasion Dual 4Ω

- 13 -

Configuracion Bi-Amplificada

2 amplificadores monofónicos

1(un) bajo Se quita el puente Carga a 4Ω

ESPAŃOL

*JUMPER is Removed *JUMPER is Removed

1 amplificador monofónico

1(un) bajo

Puente fijado en serie

Carga a 4Ω(2Ω+2Ω)

1 amplificador monofónico

1(un) bajo

Puente fijado en Paralelo

Carga a 4Ω(2Ω+2Ω)

Amplificador 1,2 ch

1(un) bajo

Se quita el puente

Carga a 2Ω

1 amplificador monofónico

2 (Dos) bajos

Puente fijado en serie

Subwoofers wired in Parallel

Carga a 2Ω

1 amplificador monofónico

3 (Tres) bajos

Puente fijado en serie

Subwoofers wired in Parallel

Carga a 1.3Ω

1 amplificador monofónico

4 (Cuatro) bajos

Puente fijado en serie

Subwoofers wired in Parallel

Carga a 1Ω

Diagramas de Aplicasion Dual 2Ω

- 14 -

Configuracion Bi-Amplificada

2 amplificadores monofónicos

1(un) bajo Se quita el puente Carga a 2Ω

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

JUMPER

SERIES PARALLEL

Input Bi-Amp Input

Only

+

-

Jumper Plug

2Ω

1Ω

2Ω

2Ω2Ω

4Ω

2Ω

Mono

SERIES PARALLEL

Input Bi-Amp Input

Only

+ +

-

Stereo

Mono

2Ω

4Ω 4Ω

2Ω

2Ω 2Ω 2Ω

Mono

2Ω

4Ω

1.3Ω

2Ω

Mono

2Ω

4Ω

1Ω

2Ω

4Ω

2Ω

4Ω

2Ω

4Ω

2Ω

4Ω

2Ω 2Ω

4Ω

2Ω

Mono

2Ω 2-Chan

ESPAŃOL

*JUMPER is Removed *JUMPER is Removed

C

B

A

G

H

I

B

A

CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240

A 15-13/32 inch (391.7 mm)

16-13/32 inch (417.1 mm)

B 15-13/32 inch (391.7 mm)

16-13/32 inch (417.1 mm)

C

11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)

D

9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm)

E

9-23/32 inch (247 mm) 11-10/32 inch (295 mm)

F

G

4/32 inch (3 mm) 4/32 inch (3 mm)

1.57 ft

3

(0.045 m

3

) 2.17 ft

3

(0.062 m

3

)

CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240

A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)

B

18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)

C

13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)

D

9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm)

E

9-23/32 inch (247 mm) 11-10/32 inch (295 mm)

F

4/32 inch (3 mm) 4/32 inch (3 mm)

G

1 inch (25.4 mm) 1 inch (25.4 mm)

H

13 inch (330.2 mm) 14 inch (355.6 mm)

I

J

13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)

1.85 ft

3

(0.052 m

3

) 2.54 ft

3

(0.072 m

3

)

Para instalar la caja sellada

Cuando el altavoz no se pueda instalCuando el altavoz no se pueda instalCuando el altavoz no se pueda instalusar MDF—20 mm (3/4 pulg.) como

material para la caja.

Pantallas acústicas delantera y trasera (x 2)

Lados izquierdo y

derecho (x 2)

Lados superior e

inferior (x 2)

* Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado)

Dimensión del

oricio de

montaje

Pantallas acústicas delantera y trasera (x 2)

Lados izquierdo y

derecho (x 2)

Lados superior e

inferior (x 2)

* Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado)

Dimensión del

oricio de

montaje

Para instalar la caja sellada

Lados superior e inferior (x 2)Cuando el altavoz no se pueda instalar en el automóvil, construya la caja sellada recomendada en la tablade

abajo—Asimismo, serecomienda usar

MDF—20 mm(3/4 pulg.) como material para la caja.

- 15 -

ESPAŃOL

J : El Volumen interior

G : El Volumen interior

- 16 -

ESPAŃOL

Impedancia nominal (Ω)

SPL (dB,1W/1M) SPL : Nivel de presión de sonido

Desplazamiento (litro)

Diámetro del orificio cortado (pulgada)

(mm)

Profundidad de montaje (pulgada)

(mm)

Re (Ω)

Re : Resistencia de la bobina móvil de

CC

BL (T.M)

BL : Producto de densidad de flujo y

longitud efectiva del cable de la

bobina móvil

Vas (litro)

Vas: Volumen de aire equivalente en

conformidad con el excitador

Me : Masa efectivaMe (g)

D (mm) D : Diámetro efectivo del cono

Fs : Resonancia del aire sin excitadorFs (Hz)

Qms

Qes

Qts

Pe [máx.] (W)

Xmax. (mm)

Respuesta de frec (Hz)

Masa del imán (oz)

(g)

Diám.de la bobina móvil (pulgada)

(mm)

Hvc (mm) Hvc : Altura de bobina móvil

Hag (mm) Hag : Altura de entrehierro

Parámetros NOTAS

Vas (pies cúbicos)

Qts : Total Q dei excitador a Fs

Pe[max.] : Potencia máxima de

entrada contínua

Qms : Q del excitador a Fs considerando

sólo la resistencia no eléctrica

Qes : Q del excitador a Fs considerando

sólo la resistencia eléctrica

Xmax. : Máximo desplazamiento

efectivo de la bobina móvil sin distorsón

parallel

83.49 dB

series seriesparallel

0.98 Ω 3.83 Ω 7.6 Ω1.92 Ω

6.85 13.75 17.218.68

17.08 L 16.98 L 18.28 L18.08 L

39.6 Hz 39.5 Hz 41.8 Hz41.7 Hz

10.261 10.282 9.1699.021

0.756 0.74 0.8240.83

0.704 0.691 0.7560.76

145.986 g 147.109 g 122.443 g124.084 g

0.6 ft

3

0.599 ft

3

0.65 ft

3

0.64 ft

3

83.54 dB 84.12 dB84.02 dB

25 ~500 Hz

6 - 14/32 inch

( 163.5 mm )

CS-AW7040CS-AW7020

2Ω + 2Ω 4Ω + 4Ω

Dia. 2 - 5/32 inch

( 54.5 mm )

39.9 mm

10 mm

39.6 mm

Dia. 2 - 4/32 inch

( 53.59 mm )

14.95 mm 14.8 mm

65.4 oz

( 1854.1 g )

600 W

Dia. 202 mm

Dia. 9 - 6/32 inch

( 233 mm )

0.123 ft

3

Impedancia nominal (Ω)

SPL (dB,1W/1M) SPL : Nivel de presión de sonido

Desplazamiento (litro)

Diámetro del orificio cortado (pulgada)

(mm)

Profundidad de montaje (pulgada)

(mm)

Re (Ω)

Re : Resistencia de la bobina móvil de

CC

BL (T.M)

BL : Producto de densidad de flujo y

longitud efectiva del cable de la

bobina móvil

Vas (litro)

Vas: Volumen de aire equivalente en

conformidad con el excitador

Me : Masa efectivaMe (g)

D (mm) D : Diámetro efectivo del cono

Fs : Resonancia del aire sin excitadorFs (Hz)

Qms

Qes

Qts

Pe [máx.] (W)

Xmax. (mm)

Respuesta de frec (Hz)

Masa del imán (oz)

(g)

Diám.de la bobina móvil (pulgada)

(mm)

Hvc (mm) Hvc : Altura de bobina móvil

Hag (mm) Hag : Altura de entrehierro

Parámetros NOTAS

Vas (pies cúbicos)

Qts : Total Q dei excitador a Fs

Pe[max.] : Potencia máxima de

entrada contínua

Qms : Q del excitador a Fs considerando

sólo la resistencia no eléctrica

Qes : Q del excitador a Fs considerando

sólo la resistencia eléctrica

Xmax. : Máximo desplazamiento

efectivo de la bobina móvil sin distorsón

parallel

85.13 dB

series seriesparallel

0.98 Ω 3.84 Ω 7.61 Ω1.94 Ω

6.84 13.72 19.149.56

38.7 L 38.76 L 35.05 L35.23 L

34.6 Hz 34.5 Hz 38 Hz37.9 Hz

10.277 10.089 9.0148.931

0.786 0.765 0.7810.794

0.73 0.711 0.7190.73

171.854 g 172.934 g 157.336 g157.028 g

1.37 ft

3

1.37 ft

3

1.24 ft

3

1.24 ft

3

85.2 dB 85.65 dB85.87 dB

23 ~500 Hz

7 - 6/32 inch

( 182.5 mm )

CS-AW7240CS-AW7220

2Ω + 2Ω 4Ω + 4Ω

Dia. 2 - 5/32 inch

( 54.5 mm )

39.9 mm

10 mm

39.6 mm

Dia. 2 - 4/32 inch

( 53.59 mm )

14.95 mm 14.8 mm

86.2 oz

( 2443.7 g )

600 W

Dia. 246 mm

Dia. 10 - 29/32 inch

( 277 mm )

0.18 ft

3

1-9/32 inch

[ 32.69 mm ]

7-7/32 inch [ 182.5 mm ]

Dia. 10-28/32 inch [ 275.94 mm ]Dia. 9-4/32 inch [ 231.96 mm ]

1-9/32 inch

[ 32.51 mm ]

6-14/32 inch [ 163.5 mm ]

Dia. 11-20/32 inch

[ 295 mm ]

8-

Dia.

7/32

inch

[ 5.5 mm ] HOLES

Dia. 12-24/32 inch [ 324 mm ]

Dia. 12-12/32 inch [ 314 mm ]

Dia. 10-26/32 inch [ 275 mm ]

Dia. 10-14/32 inch [ 265 mm ]

Dia. 9-23/32 inch

[ 247 mm ]

8-

Dia.

7/32

inch

[ 5.5 mm ] HOLES

CS-AW7020 CS-AW7220

CS-AW7040 CS-AW7240

- 17 -

Air Vented

Aluminum

Cast Basket

Integlated Dual-Layer

Cone construction

Woven Tinsel Lead

(Patent Pending)

Rapid Fire Impedance

Selector Speaker Terminal

( Patent Pending)

Dual Stacked

Strontium Magnet

Dual Diametric

Progressive Spider

Multi Mount Smart

Trim Ring

(Patent Pending)

Glass Fiber

Laminated

Hemp Cone

Hemp-Fiber Drive

Cone

Aluminum Voice

Coil Former

Santoprene Surround

4 (2+2) Layer Voice Coils

Aero Vent Bottom Plate

T3 Chassis (Thermal Transfer Technology)

Heat Transfer Silicon

- 18 -

- 19 -

TO OUR VALUED CUSTOMER

IS HERE TO HELP!

Do not attempt to service the product yourself

Caution

To prevent electrical shock, do not open the cabinet.

There are no user serviceable parts inside.

Please refer to qualified service personnel for repairs.

NEED HELP ON HOW TO HOOK UP?

NEED ASSISTANCE ON HOW TO OPERATE?

NEED TO LOCATE A JVC SERVICE CENTER?

LIKE TO PURCHASE ACCESSORIES?

THANK YOU FOR PURCHASING THIS JVC PRODUCT.

WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.

Remember to retain your Bill of Sale for Warranty Service.

TOLL FREE: 1(800)252-5722

http://www.jvc.com

Printed in China

EN, FR, SP

JVC CS-AW7020 Manuel utilisateur

JVC CS-AW7020 Manuel utilisateur

Documents connexes

Autres documents