Yamaha V3 Manuel utilisateur

EN

How to Use This Reference Manual

The QL5/QL1 Reference Manual (this document) allows you to

search for terms and take advantage of links in the text.

Searching for terms

To search for a term, use the search function of the software

you're using to view this document.

If you're using Adobe Reader, enter the term in the search box

and press the <Enter> key of your computer keyboard to search

for occurrences of that term.

Displaying the next/previous view

If you're using Adobe Reader, you can jump to the previous/next

view in your viewing history. This is a convenient way to jump back

to the previous page after you've used a link to jump to a different

page.

Using the Function Tree

A function tree for the QL series is provided on page 4 and

following. You can use this function tree to find the page that

explains an on-screen display or function.

Reference Manual

Contents

Reference Manual

2

Contents

How to Use This Reference Manual .......................................................................... 1

Function Tree ............................................................................ 4

SELECTED CHANNEL section ...................................................... 6

Operations in the SELECTED CHANNEL section ....................................................... 6

Channel Strip section.............................................................. 11

Operations in the Channel Strip section................................................................. 11

Input and output patching..................................................... 14

Changing the input patch settings......................................................................... 15

Changing the output patch settings ...................................................................... 16

Inserting an external device into a channel ............................................................ 18

Directly outputting an INPUT channel ................................................................... 21

Input channels ........................................................................ 23

Signal flow for input channels................................................................................ 23

Specifying the channel name, icon, and channel color........................................... 24

Making HA (Head Amp) settings............................................................................ 26

Sending the signal from an input channel to the STEREO/MONO bus ................... 30

Sending a signal from an input channel to a MIX/MATRIX bus .............................. 34

Channel name display indication ........................................................................... 37

Correcting delay between channels (Input Delay).................................................. 37

Surround output for input channels....................................................................... 40

Channel library operations..................................................................................... 44

OUTPUT channels.................................................................... 45

Signal flow for output channels ............................................................................. 45

Specifying the channel name, icon, and channel color........................................... 46

Sending signals from MIX channels to the STEREO/MONO bus ............................. 47

Sending signals from MIX channels and STEREO/MONO channels to

MATRIX buses............................................................................................. 49

Correcting delay between channels (Output Delay)............................................... 51

Using the PORT TO PORT function ........................................................................ 52

Channel library operations..................................................................................... 53

EQ and Dynamics ..................................................................... 54

Using EQ ................................................................................................................ 54

Using dynamics ...................................................................................................... 57

Using the EQ or Dynamics libraries ......................................................................... 60

Channel Job ............................................................................. 61

DCA group............................................................................................................. 61

Mute group............................................................................................................ 63

Using the Recall Safe function................................................................................. 66

Channel Link function ............................................................................................ 69

Copying, moving, or initializing a channel.............................................................. 74

About Mix Minus.................................................................................................... 77

Scene memory ......................................................................... 79

Storing and recalling scenes ................................................................................... 80

Editing scene memories.......................................................................................... 84

Using the Global Paste function.............................................................................. 86

Using the Focus Recall function .............................................................................. 88

Using the Fade function.......................................................................................... 90

Outputting a control signal to an external device in tandem with scene recall

(GPI OUT) ................................................................................................... 92

Playing back an audio file that links to a scene recall............................................... 93

Using Preview mode............................................................................................... 94

Monitor and Cue functions ..................................................... 96

Using the Monitor function .................................................................................... 97

Using the Cue function......................................................................................... 103

Talkback and Oscillator......................................................... 108

Using Talkback ..................................................................................................... 108

Using the Oscillator function ................................................................................ 110

Meters.................................................................................... 113

Operations in the METER screen ........................................................................... 113

Graphic EQ, Parametric EQ, effects, and Premium Rack....... 118

About the virtual rack ........................................................................................... 118

Virtual rack operations.......................................................................................... 119

Graphic EQ operations ......................................................................................... 122

About AUTOMIXER............................................................................................... 129

Editing the internal effects .................................................................................... 132

Effects and tempo synchronization ....................................................................... 138

Using the Premium Rack....................................................................................... 139

Using the graphic EQ, parametric EQ, effect, and Premium Rack libraries ............. 148

Contents

Reference Manual

3

I/O devices and external head amps .................................... 149

Using an I/O device ............................................................................................. 149

Remotely controlling an R series unit ................................................................... 151

Remotely controlling an amp............................................................................... 154

Remotely controlling WIRELESS unit..................................................................... 155

Using an external head amp ................................................................................ 156

Remotely controlling an external head amp......................................................... 158

Controlling an internal head amp ........................................................................ 160

MIDI....................................................................................... 161

MIDI functionality on the QL series console ......................................................... 161

Basic MIDI settings .............................................................................................. 161

Using program changes to recall scenes and library items.................................... 164

Using control changes to control parameters....................................................... 166

Using Parameter Changes to control parameters ................................................. 168

Recorder................................................................................ 169

About the USB memory recorder ......................................................................... 169

Assigning channels to the input/output of the recorder ....................................... 169

Recording audio to a USB flash drive.................................................................... 171

Playing back audio files from a USB flash drive ..................................................... 173

Editing the title list............................................................................................... 174

Recording or playing back using a computer DAW .............................................. 175

Using the QL console with Nuendo Live .............................................................. 178

Setup ..................................................................................... 182

About the SETUP screen....................................................................................... 182

User settings ........................................................................................................ 185

Preferences .......................................................................................................... 192

USER DEFINED keys ............................................................................................. 194

Functions that can be assigned to USER DEFINED keys ........................................ 195

USER DEFINED knobs........................................................................................... 199

Functions that can be assigned to USER DEFINED knobs ...................................... 200

Custom fader bank .............................................................................................. 202

Console Lock ....................................................................................................... 203

Saving and loading setup data to and from a USB flash drive............................... 204

Word clock and slot settings ................................................................................ 211

Using cascade connections .................................................................................. 213

Basic settings for MIX buses and MATRIX buses ................................................... 216

Switching the entire phantom power supply on/off ............................................. 217

Specifying the brightness of the touch screen, LEDs, channel name displays,

and lamps................................................................................................. 217

Setting the date and time of the internal clock..................................................... 218

Setting the network address ................................................................................ 218

Setting up the Dante audio network..................................................................... 219

Using GPI (General Purpose Interface) .................................................................. 230

Help function......................................................................... 235

Loading a Help/text file from a USB flash drive ..................................................... 235

Viewing Help........................................................................................................ 235

Using USER DEFINED keys to recall Help directly................................................... 236

Other functions ..................................................................... 237

Initializing the unit to factory default settings ....................................................... 237

Adjusting the detection point of the touch screen (Calibration function) .............. 237

Adjusting the faders (Calibration function) ........................................................... 238

Fine-tuning the input and output gain (Calibration function) ............................... 238

Adjusting the LED color (Calibration function) ...................................................... 240

Adjusting the brightness of the channel name display .......................................... 240

Adjusting the contrast of the channel name display.............................................. 241

Initializing the Dante audio network settings ........................................................ 241

Warning/Error Messages ...................................................... 242

Index...................................................................................... 245

Function Tree

Reference Manual

4

Function Tree

Page numbers in parentheses ( ) are the page numbers of the

Owner’s Manual (booklet).

Main

SELECTED CHANNEL 6

OVERVIEW 11

FUNCTION ACCESS AREA (17)

CHANNEL PARAMETER

PATCH/NAME 15, 24, 46

GAIN/PATCH 26

1ch 26

8ch 27

CH1–32 29

CH33–64/ST IN 29

OUTPUT

Indication only

INPUT DELAY 37

8ch 37

CH1–32 38

CH33–64/ST IN 38

DELAY SCALE 37

INSERT/DIRECT OUT 19

1ch 19, 21

8ch 19, 22

HPF/EQ 54

1ch 54

8ch 56

CH1–32 56

CH33–64/ST IN 56

OUTPUT 56

DYNAMICS 57

1ch 57

KEY IN SOURCE SELECT 58

8ch 59

CH1–32 59

CH33–64/ST IN 59

OUTPUT 59

MIX SEND/MATRIX SEND 36

TO STEREO/MONO 47

8ch 47

CH1–32 48

CH33–64/ST IN 48

OUTPUT 48

SURROUND 40

LIBRARY

CHANNEL LIBRARY 44

EQ LIBRARY 60

DYNAMICS LIBRARY 60

GEQ/PEQ LIBRARY 148

EFFECT LIBRARY 148

Portico5033/Portico5043/U76/Opt-2A/

EQ-1A/DynamicEQ LIBRARY

148

DANTE INPUT PATCH LIBRARY 150

RACK

VIRTUAL RACK 119

RACK MOUNTER 122

GEQ EDIT 123

GEQ LINK 124

EFFECT RACK 134

EFFECT EDIT 134

EFFECT TYPE 135

PREMIUM RACK 139

PREMIUM RACK MOUNTER 140

PREMIUM RACK EDIT 141

AUTOMIXER 129

PARAMETRIC EQ 126

I/O DEVICE

DANTE PATCH 149

DANTE SETUP 149

DANTE INPUT PATCH 150

DANTE OUTPUT PATCH 151

I/O 152

REMOTE HA EDIT 154

DANTE OUTPUT PATCH 151

AMP 155

DANTE OUTPUT PATCH 151

WIRELESS 155

EXTERNAL HA 158

EXTERNAL HA PORT SELECT 159

EXTERNAL HA EDIT 159

INTERNAL HA 160

MONITOR

MONITOR 97

CUE 106

MONITOR 99

OSCILLATOR 111

TALKBACK 109

METER

INPUT METER 113

OUTPUT METER 113

SETUP

USER SETUP 182

PREFERENCE 192

USER DEFINED KEYS SETUP 194

USER DEFINED KEY SETUP (List) 194

USER DEFINED KNOBS SETUP 199

USER DEFINED KNOB SETUP (List) 199

CUSTOM FADER BANK/MASTER FADER 202

FADER ASSIGN SELECT 202

USER LEVEL/CREATE USER KEY 185

CREATE KEY 186

SAVE KEY 189

LOGIN 187

SAVE/LOAD 204

WORD CLOCK/SLOT 211

Function Tree

Reference Manual

5

NOTE

• The explanations in this reference manual will use the QL5.

• In the case of the QL1, some screens will not show channels

and faders that do not exist on those models.

CASCADE IN/OUT PATCH 214, 215

OUTPUT PORT 51

MIDI/GPI 161, 230

MIDI SETUP 162

PROGRAM CHANGE 164

CONTROL CHANGE 167

GPI 231

FADER START 233

BUS SETUP 216

CONSOLE LOCK 203

DATE/TIME 218

NETWORK 219

DANTE SETUP 219

SCENE

SCENE LIST 81

GLOBAL PASTE 87

FADE TIME 91

SONG SELECT 94

FOCUS RECALL 89

PREVIEW 94

RECORDER

USB 169

NUENDO LIVE 178

CH JOB

CH LINK MODE 70

DCA GROUP ASSIGN 62

MUTE GROUP ASSIGN 64

RECALL SAFE MODE 67

CH COPY MODE 74

CH MOVE MODE 76

CH DEFAULT MODE 77

SETUP PATCH

PORT SELECT

20, 22, 28, 100,

107, 150, 159,

215

CH SELECT 17, 120, 170, 202

Others

CONFIRMATION 192

SOFT KEYBOARD (23)

LOGIN 187

Startup Menu

MODE SELECT 237

INITIALIZE ALL MEMORIES 237

INITIALIZE CURRENT MEMORIES 237

TOUCH SCREEN CALIBRATION 237

INPUT PORT TRIM 239

OUTPUT PORT TRIM 239

SLOT OUTPUT TRIM 239

FADER CALIBRATION 238

LED COLOR CALIBRATION 240

SELECTED CHANNEL section

Reference Manual

6

SELECTED CHANNEL section

The SELECTED CHANNEL section located at the right of the display corresponds to a

channel module of a conventional analog mixer, and allows you to use the knobs on the panel

to set all the major parameters of the currently-selected channel.

Operations in this section will affect the channel that was most recently selected by its [SEL]

key. If you have assigned an ST IN channel or STEREO channel to a single channel strip,

either the L or the R channel will be selected, and the major parameters for L and R channels

will be linked.

Operations in the SELECTED CHANNEL section

Follow the steps below to perform operations in the SELECTED CHANNEL section.

NOTE

• The number and name of the currently-selected

channel is shown in the channel select field located in

the Function Access Area of the touch screen.

• If an ST IN channel or STEREO channel has been

assigned to a single channel strip, you can switch

between L and R by repeatedly pressing the same

[SEL] key.

• You can also switch channels by pressing the channel select field located in the Function Access

Area. Press the left side of the field to select the preceding channel. Press the right side of the

field to select the next channel.

• If you have turned on the option “POPUP APPEARS WHEN KNOB(S) PRESSED” on the

PREFERENCE tab (accessed by pressing the SETUP button, then the USER SETUP button),

pressing a knob repeatedly will open or close the screen (1ch).

• Even if a different screen is selected, the channel selected with the

[SEL] key can be set using the knobs of the SELECTED CHANNEL

section. In this case, a window indicating the value of that parameter will

appear on screen when you operate a knob.

SELECTED CHANNEL VIEW screen

 SEND field

In this field, you can view the send level and pre/post from the channel

to each MIX/MATRIX bus. You can also switch the on/off status of the

send signals. The view and the function of the knobs and buttons in

the SEND field vary depending on whether a pair of bus channels

(odd-numbered and even-numbered) are comprised of two mono

channels or a stereo channel.

1 Tabs

Enable you to select a group of 16 output bus channels to be

displayed in the SEND field.

• MIX tab .................................. displays MIX buses 1–16.

• MATRIX tab ........................... displays MATRIX buses 1–8.

STEP

1. Press the Bank Select keys in the Fader Bank section to select the bank that includes

the channel you want to operate.

2. Use a [SEL] key in the top panel channel strip section or the master section, to select

the channel to control.

3. If the SELECTED CHANNEL VIEW screen is not displayed, press one of the knobs in

the SELECTED CHANNEL section.

4. Use the knobs and the buttons in the screen to edit the parameters of the selected

channel.

Channel number

Channel name

1

SELECTED CHANNEL section

Reference Manual

7

If the destination bus channels are two mono channels:

1 SEND knob

Adjusts the send level to the corresponding bus.

2 PRE indicator

Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND

8ch screen is turned ON, this PRE indicator will be turned on.

3 ON button

Switches the send signal to the corresponding bus on or off.

If the destination bus is a stereo channel:

1 SEND/PAN knob

The right-hand knob adjusts the level of the signal sent to a pair of bus channels (even-

numbered and odd-numbered). The left-hand knob adjusts the pan and balance of the

same signal.

2 PRE indicator

Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND

8ch screen is turned ON, this PRE indicator will be turned on.

3 ON button

Switches the send signal to the two buses on or off.

NOTE

• If the indices of a SEND/PAN knob are white, the send point is assigned as PRE; if the indices

are black, it is assigned as POST.

• If the send point is PRE, you can specify the PRE point as either VARI [PRE EQ] or VARI [PRE

FADER] in the BUS SETUP popup that appears when you press the SETUP button  BUS

SETUP button.

• If the type of the destination bus is set to FIXED, controllers

1–2 mentioned above will not be

displayed. The send level will be fixed at nominal level, and the send point will be fixed at POST

FADER. For details, see “Basic settings for MIX buses and MATRIX buses” on page 216.

• Press the SEND knob or PAN knob on screen to open the SEND 8ch window.

 GAIN/PATCH field

This field enables you to make HA (head amp) analog or digital gain settings. You can also

view the operational status of the head amp.

1 GAIN knob

Sets the analog gain/digital gain of the head amp.

Press the knob to open the GAIN/PATCH 1ch

window.

2 GC indicator

Indicates the fixed gain value output to the audio

network if the Gain Compensation function is

turned on.

3 OVER indicator

Warns you when the signal is clipping.

4 Ø (Phase) indicator

Indicates the status of the phase setting.

5 +48V indicator

Indicates the phantom power (+48V) on or off status for the head amp.

6 HPF ON indicator

Indicates the HPF on/off status of the external head amp.

7 AG-DG LINK indicator

Indicates a link between the analog gain and digital gain of the head amp.

8 Digital/Analog gain value

If analog gain is assigned to the GAIN knob, the digital gain value is shown here. If digital

gain is assigned to the GAIN knob, the analog gain value is shown here.

NOTE

• For an input channel that is patched to an input that has no head amp, 1, 2, 5, 6, and 7

will not be shown. For an output channel,

1–7 will not be shown.

• If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the USER SETUP PREFERENCE

screen, the digital gain knob will appear for

1, and 2, 5, 6, and 7 will not be shown. For

details, refer to “Making HA (Head Amp) settings” on page 26.

1

2

3

1

2

3

5

876

1

4

2

SELECTED CHANNEL section

Reference Manual

8

 PAN/BALANCE field

This field enables you to switch the on/off status of the signal sent from the selected channel

to the STEREO/MONO bus, and adjust the pan and balance.

The view and the function of the controllers in this field vary depending on the type of the

selected channel.

When an input channel or MIX channel is selected:

1 TO STEREO PAN knob

Sets the pan position of a signal routed to the

STEREO bus.

Press the knob to open the STEREO/MONO 8ch

window. If the ST IN channel is selected, you can

specify whether to view the PAN knob or the

BALANCE knob in this window. For a MIX channel,

the PAN knob will appear if the signal is mono, and the BALANCE knob will appear if the

signal is stereo.

NOTE

• For mono input channels, the pan level is nominal at center and +3dB when panned either left or

right. These levels do not change even if channel link is used.

• For ST IN channels, if the PAN knob is selected, the pan level is nominal when panned either left

or right and -3dB at center. If the BALANCE knob is selected the balance level is nominal at

center and +3dB when panned either left or right. These levels do not change even if channel link

is used.

2 ST/MONO button

Switches the on/off status of a signal sent from the

channel to the STEREO/MONO bus.

If an INPUT/MIX channel is set to LCR mode, the

LCR button appears in location

2. The LCR button

is an overall on/off switch for the signals sent from

the channel to the STEREO/MONO bus.

When a MATRIX, STEREO, or MONO channel is selected:

1 BALANCE knob

If the signal on the selected channel is stereo, the

BALANCE knob will appear, enabling you to adjust

the volume balance for the left and right channels.

If the channel signal is monaural, the BALANCE

knob is not shown and cannot be used.

Press the knob to open the TO STEREO 8ch

window.

When using Surround mode (MIX1-MIX6)

3 DOWN MIX

This field enables you to view the downmix

coefficient and L/R button settings.

Press this field to open the TO STEREO/MONO

window.

 INPUT DELAY field

This field enables you to view the delay settings.

1 ON indicator

Indicates the on/off status of the delay.

2 Delay time

The delay value is displayed by milliseconds (ms) and also by currently-selected scale. If

the scale uses units of ms, the value in the bottom row will not be displayed. Only the

ms value appears in the middle row.

Press this field to open the INPUT DELAY 8ch window.

 HPF field (input channels only)

This field enables you to set the HPF. If an output channel

is selected, a gray circle will appear in location

1, and 2

will not be displayed.

1 HPF knob

Sets the HPF cutoff frequency.

2 ON button

Switches the HPF on or off.

1

2

1

3

1

2

1

2

SELECTED CHANNEL section

Reference Manual

9

 EQ parameter field

This field displays the 4-band EQ parameter settings. Press each

knob to open the HPF/EQ 1ch window.

1 Q knob

Specifies the Q for each band.

If the HIGH band filter type is set to LPF or H. SHELF (high-

shelving), or the LOW band filter type is set to L. SHELF

(low-shelving), the Q knob will not be displayed. Only the

filter type name will be displayed.

NOTE

• Fully rotating the HIGH band Q knob on the panel counter-

clockwise while pressing and holding it down will set the filter

type to LPF. Fully rotating the Q knob clockwise while pressing

and holding it down will set the filter type to high-shelving.

• Fully rotating the LOW band Q knob on the panel clockwise while

pressing and holding it down will set the filter type to low-

shelving.

• If an output channel has been selected, fully rotating the LOW

band Q knob on the panel counter-clockwise while pressing and holding it down will set the filter

type to HPF.

• You can also switch the filter type in the HPF/EQ 1ch window.

2 FREQUENCY knob

Sets the center frequency (or cutoff frequency) for each band.

3 GAIN knob

Sets the amount of cut/boost for each band.

NOTE

• If the HIGH band filter type is set to LPF, you can switch LPF on or off using the HIGH band GAIN

knob on the panel.

• If the LOW band filter type is set to HPF, you can switch HPF on or off using the LOW band GAIN

knob on the panel.

 EQ graph field

This field graphically indicates the approximate response of the EQ. Press this field to open

the HPF/EQ 1ch window, in which you can set the attenuator, HPF, and EQ.

 DYNAMICS 1/DYNAMICS 2 field

This field enables you to set the Dynamics 1/2 parameters.

1 OVER indicator

Warns you when the signal is clipping.

2 Level meter

Displays the output signal level (green) and the amount of gain reduction (orange)

when the Dynamics is on. The current threshold setting is shown as a white vertical line.

3 Threshold

Specifies the threshold.

4 Parameters

Indicate the values of parameters that vary depending on the currently-selected

dynamics type.

Press this field to open the DYNAMICS 1/DYNAMICS 2 1ch window, in which you can

make detailed parameter settings.

 INSERT field

This field enables you to make insert settings.

1 Popup button

Press this button to open the INSERT/DIRECT OUT 1ch

window.

2 ON button

Switches the insert on or off.

3 RACK EDIT button

Appears if an effect or Premium Rack is inserted. Press this button to display the edit

screen for the inserted rack.

4 IN indicator

Appears if a port has been assigned to the insert-in patch. It lights when the signal is

sent to the insert-in.

1 2 3

1 2

3

4

1

2

43

SELECTED CHANNEL section

Reference Manual

10

 DIRECT OUT field

This field enables you to make Direct Out settings.

1 Popup button

Press this button to open the INSERT/DIRECT OUT 1ch

window. The Direct Out level value will appear below the

button.

2 ON button

Switches the Direct Out on or off.

 RECALL SAFE field

This field enables you to make Recall Safe settings.

1 Popup button

Press this button to open the RECALL SAFE window.

2 ON button

Switches the Recall Safe status on or off.

3 PARTIAL indicator

This will light if recall safe applies only to some of the parameters, not to all channel

settings.

 FADER field

This field enables you to make settings for the channel on/off

status and the level.

1 Fader

Displays the current level.

Use the faders on the top panel to set the levels.

2 Level indicator

Displays the current level setting by numerical value. If

the signal is clipping at any point in the channel, the ΣCLIP indicator will light.

3 ON button

Switches the channel on or off. The button is linked with the corresponding [ON] key

on the top panel.

 DCA/MUTE field

This field enables you to select the DCA or mute group to which the

channel is assigned.

1 Tabs

Select a DCA or mute group. Press the selected tab once again

to open the DCA/MUTE GROUP ASSIGN MODE window.

When the DCA group tab is selected:

2 DCA group select buttons

Select the DCA group to which the channel is assigned.

3 Mute group indicators

Indicate the mute group to which the channel is assigned.

When the mute group tab is selected:

4 Mute group select buttons

Select the mute group to which the channel is assigned.

NOTE

If the dimmer level is set to the mute group, this button lights

orange.

5 MUTE SAFE button

Temporarily removes the channel from the mute group.

6 DCA group indicators

Indicate the DCA group to which the channel is assigned.

21

2

1

3

1

2

3

1

3

2

1

3

2

4

5

6

Channel Strip section

Reference Manual

11

Channel Strip section

The Channel Strip section located below the touch screen lets you recall and control input

channels, output channels, or DCA groups. If you press the Bank Select key in the Fader Bank

section, you can control them using the faders, [ON] keys, and [CUE] keys for the channels

or DCA groups corresponding to that key.

Operations in the Channel Strip section

 CHANNEL NAME field

This field appears at the top and bottom of the screen and displays the channel number,

name, and icon for the currently-selected eight channels. The name of the currently-selected

channel is highlighted.

 GAIN/PATCH field

This field enables you to make HA (head amp) analog or digital gain settings. You can also

view the operational status of the head amp.

The view and the function of the controllers in this field vary depending on the type of the

selected channel.

If the head amp is patched:

1 GAIN knob

Sets the analog gain of the head amp.

• Press this field to assign the GAIN knob to the [TOUCH AND TURN] knob, which

enables you to adjust the gain. If the Gain Compensation function is turned on, an

indicator appears, showing the level of the signal output to the audio network.

• If the GAIN knob has been assigned to the [TOUCH AND TURN] knob, press the knob

to open the GAIN/PATCH 8ch window.

2 OVER indicator

Lights when a signal at the input port or from the rack output exceeds the full scale level.

This indicator is available only if an input channel is selected.

3 +48V indicator

Indicates the phantom power (+48V) on or off status for the head amp. This indicator is

not displayed unless the head amp is patched to the channel.

4 Ø (Phase) indicator (input channels only)

Indicates the input phase setting for the head amp.

NOTE

• If the slot is not connected to the head amp, the patch and the type of the MY card will be

displayed.

• Press the SETUP button, then the USER SETUP button, select the PREFERENCE tab, and then

set the GAIN KNOB FUNCTION to DIGITAL GAIN. You will be able to adjust the digital gain value

by using the [TOUCH AND TURN] knob.

STEP

1. Use the Bank Select keys to select the channels or DCA groups that you want to

control.

2. Use the faders and [ON] keys in the Channel Strip section to adjust the level of the

selected channels and switch them on or off.

3. Use the fields on the OVERVIEW screen and the [TOUCH AND TURN] knob to adjust

the parameters for the channels.

Bank Select keys

Channel Strip section

OVERVIEW screen

NOTE

The OVERVIEW screen

appears when you press a

USER DEFINED key to which

OVERVIEW is assigned.

: Selected channel

: Unselected channel

1

4

3

2

Channel Strip section

Reference Manual

12

• If GAIN KNOB FUNCTION is set to DIGITAL GAIN, the DIGITAL GAIN knob will appear instead

of knob

1, and indicator 3 will not be displayed.

• You can also operate the digital gain by assigning INPUT GAIN DIGITAL GAIN to a USER

DEFINED knob, or by assigning an ALTERNATE function to a USER DEFINED key and then

adjusting the USER DEFINED knob or the GAIN knob for the selected channel while

ALTERNATE is on.

 INPUT DELAY field (input channels only)

This field displays the delay status for the input channel. Press this field to open the INPUT

DELAY 8ch window.

1 DELAY ON/OFF indicator

Indicates the on/off status of the delay.

 INSERT/DIRECT OUT field

This field displays the Insert/Direct out status. Press this field to open the INSERT 8ch

window.

1 INSERT ON/OFF indicator

Indicates the insert on/off status.

2 DIRECT OUT ON/OFF indicator (input channels only)

Indicates the Direct Out on/off status.

 EQ field

This field graphically indicates the approximate response of

the EQ. Press this field to open the HPF/EQ 1ch window, in

which you can set the HPF and EQ.

NOTE

If DCA or monitor has been selected, this field will be blank.

 DYNAMICS 1/2 field

This field displays the threshold value and meter for Dynamics

1/2. Press this field to open the DYNAMICS 1/2 1ch window.

NOTE

If DCA or monitor has been selected, this field will be blank.

 SEND field

This field displays the send level, send on/off status, and pre/post

settings for 16 buses.

To select the 16 destination buses, use the [MIX/MATRIX] key in the

Fader Bank section.

Use the [TOUCH AND TURN] knob to adjust the send level for each bus.

Touch the knob of the bus you want to operate; it will be assigned to the

[TOUCH AND TURN] knob. If it is assigned to the [TOUCH AND TURN]

knob, touching that knob once again will display the SEND 8ch popup

screen.

This field varies depending on the type of the destination bus.

If the destination bus is VARI (mono):

The knob color and scale color indicate the send on/off and pre/post

status. If the send is off, the knob color turns gray. With the post setting,

the knob scale color turns gray.

If the slot is patched:

The slot name will appear.

If the rack is connected:

The patch and module name will appear.

If the output is connected:

Only the patch will appear.

1

2

Channel Strip section

Reference Manual

13

If the destination bus is VARI (stereo):

If a pair of buses (odd-numbered and even-numbered) are in stereo, the left-hand knob will

function as the PAN knob, and the right-hand knob will function as the SEND knob.

If the destination bus is set to FIXED:

The SEND ON/OFF button for each bus is shown instead of the knob.

 TO STEREO/MONO field

This field displays the on/off status and pan/balance setting of the signal sent to the STEREO/

MONO bus.

This field varies depending on the type of the selected channel.

When an input channel or MIX channel is selected:

1 TO STEREO PAN knob

Sets the pan position of a signal routed to the STEREO bus.

Press the knob to open the STEREO/MONO 8ch window. If the ST IN channel is selected,

you can specify whether to view the PAN knob or the BALANCE knob in this window.

For a MIX channel, the PAN knob will appear if the signal is mono, and the BALANCE

knob will appear if the signal is stereo.

2 ST/MONO indicator

Indicates the status of a signal sent to the STEREO/MONO bus.

If an input or MIX channel is set to LCR mode, the LCR indicator

will be displayed.

When a MATRIX channel (monaural) or MONO channel is selected:

The ΣCLIP indicator will light if the signal is clipping at some point in the channel.

For a stereo MATRIX channel or STEREO channel, the BALANCE knob appears, indicating

the balance of the left/right channels.

 DCA group field

A DCA group (1–16) to which the channel is assigned is displayed on the first or second row

in this field.

Press this field to open the DCA/MUTE GROUP ASSIGN MODE window.

 Mute group field

A mute group (1–8) to which the channel is assigned is displayed on the third row in this field.

If the channel has been temporarily removed from the mute group, S (Safe) will appear on the

third row. If a dimmer level has been specified for a mute group, the color of the characters will

change from red to orange.

Press this field to open the DCA/MUTE GROUP ASSIGN MODE window.

1

2

Input and output patching

Reference Manual

14

Input and output patching

This chapter explains how to edit the input patching and output patching, how to connect

inserts, and how to use direct outputs.

When the QL series is in the initial state, the following input ports (jacks/ports) are patched to

each input channel.

For QL5

For QL1

When the QL is in the initial state, the output ports (jacks/ports) are patched to the following

output channels.

*1. QL1: OMNI OUT1–6

*2. QL1: MIX1–6

*3. QL1: OMNI OUT7–8

Input patching

QL series consoles and I/O devices feature two types of patching: Dante audio network

patching and QL console internal patching.

For Dante audio network patching, you will use the DANTE INPUT PATCH window. In this

window, you can patch the QL console and I/O device inputs. Sixty-four (64) channels for the

QL5 and thirty-two (32) channels for the QL1 can be input from a DANTE audio network.

Choose channels from Dante audio network signals and select the I/O devices that you want

to control from the QL series console.

Then, route the input signals (that were patched in the DANTE INPUT PATCH window) to

channels on the QL series console. To do this, choose input ports from DANTE 1–64 (for QL5)

or DANTE1–32 (for QL1) in the GAIN/PATCH window.

Output patching

Use the OUTPUT PORT window to patch QL console’s output channels and Dante audio

network. In this window, assign output channel signals to DANTE 1–64 ports (for QL5) or

DANTE 1–32 ports (for QL1).

Next, patch the output signals from DANTE 1–64 (for QL5) or DANTE 1–32 (for QL1)

(assigned in the OUTPUT PORT window) to I/O device outputs. Use the OUTPUT PATCH

window of the I/O DEVICE to make these assignments.

QL console internal patching and Dante audio network

patching

The following diagram shows the signal flow through the QL series console, I/O devices, and

Dante audio network.

Input channels Input port (jack/port)

CH1–32 INPUT1–32

CH33–48 DANTE1–16

CH49–64 DANTE17–32

ST IN1L-4R FX5L(A)–FX8R(B)

Input channels Input port (jack/port)

CH1–16 INPUT1–16

CH17–32 DANTE1–16

ST IN1L-4R FX5L(A)–FX8R(B)

Output port (jack/port) Output channels

OMNI OUT1–14

*1

MIX1–14

*2

OMNI OUT15–16

*3

STEREO L/R

DANTE1–16 MIX1–16

DANTE17–24 MATRIX1–8

DANTE25–26 STEREO L/R

DANTE27 MONO

DANTE28–29 MONITOR L/R

DANTE30 MONITOR C

DANTE31–32 CUE L/R

SLOT1(1)–(16) MIX1–16

SLOT2(1)–(8) MATRIX1–8

SLOT2(9)–(10) STEREO L/R

SLOT2(11) MONO

SLOT2(12)–(13) MONITOR L/R

SLOT2(14) MONITOR C

SLOT2(15)–(16) CUE L/R

FX5L(A), FX6L(A), FX7L(A), FX8L(A) MIX13–16

DIGITAL OUT L/R STEREO L/R

RECORDER INPUT L/R STEREO L/R

Output port (jack/port) Output channels

32: QL5

16: QL1

16 16 64: QL5

32: QL1

SW

ID #2

ANALOG INPUT MY MY

INPUT PATCH

Dante Network

“Dante” (ports)

ID #3

ID #1

Dante-MY16-AUD

QL series console

I/O Device

I/O device

Dante

patching

QL series internal

patching

Input and output patching

Reference Manual

15

Changing the input patch settings

NOTE

• You can also select an input port from the GAIN/PATCH window.

• The OVERVIEW screen appears when you press a USER DEFINED key to which OVERVIEW is

assigned.

PATCH/NAME screen

1 PATCH button

Indicates the currently-selected input port. If you press this button when selecting an

icon or changing the channel name, you will return to the input port select screen.

2 Channel icon button

Indicates the icon that is selected for the corresponding channel. When you press this

button, a screen will appear in which you can select an icon or sample name.

3 Channel name input box

Indicates the name that is assigned to the corresponding channel. When you press this

field, a keyboard window allowing you to change the channel name will appear.

STEP

1.

Press the Bank Select keys in the Fader Bank section and the [SEL] keys on the top

panel to select the input channel you want to operate.

2. Press the channel number/channel name field on the OVERVIEW screen.

3. Select the type of port in the category select list on the PATCH/NAME screen, and

use the port select buttons to select the input port.

OVERVIEW screen PATCH/NAME screen

2 73

1

6

4

5

Input and output patching

Reference Manual

16

4 Category select list

Selects the category of input port. The categories correspond to the following input

ports. The displayed categories vary depending on the channel type.

• DANTE1–32...........DANTE1–DANTE32

• DANTE33–64.........DANTE33–DANTE64 (QL5 only)

• INPUT/PB OUT......INPUT1–32

*1

, PB OUT(L), PB OUT(R)

• SLOT1....................SLOT1(1)–SLOT1(16)

• SLOT2....................SLOT2(1)–SLOT2(16)

• EFFECT RACK ......FX1L(A)–FX8R(B)

• PREMIUM RACK ...PR1L(A)–PR2R(B)

*1. QL1: INPUT1–16

5 Port select buttons

Select the input port that is assigned to the currently-selected channel.

6 Tabs

Enable you to switch between items.

7 Close button

Closes the screen.

Changing the output patch settings

To change the patching, you can either select the output port that will be the output destination

of each output channel, or you can select the output channel that will be the output source for

each output port.

Selecting the output port for each output channel

NOTE

With QL V1.07 and later, when you change from input channels to output channels using the Bank

Select keys, the SEND field of the SELECTED CHANNEL VIEW screen changes from the MIX

tab to the MATRIX tab. Then, if you switch back to input channels, the MIX tab will appear.

STEP

1. Press the Bank Select keys in the Fader Bank section and the [SEL] keys on the top

panel to select an output channel.

2. Press the channel number/channel name field on the OVERVIEW screen.

3. Select the type of port in the category select list on the PATCH/NAME screen, and

use the port select buttons to select the output port.

OVERVIEW screen PATCH/NAME screen

Input and output patching

Reference Manual

17

PATCH/NAME screen

1 PATCH button

Indicates the port that is patched to the output channel. If you press this button when

another tab is active, a window will appear, enabling you to select the network and port.

2 Channel select button

Selects the channel to set.

NOTE

Switching channels on this screen will not affect the channel selection on the console.

3 Channel icon button

Indicates the icon and color that are currently selected for the corresponding channel.

When you press this button, a screen will appear in which you can select an icon or

sample name.

4 Channel number display box

Indicates the channel number. This item cannot be changed.

5 Channel name input box

Indicates the name that is assigned to the corresponding channel. When you press this

field, a keyboard window allowing you to assign a name will appear.

6 Category select list

Select the type of port.

7 Port select buttons

From the category, these buttons let you select the port to patch. To cancel the

selection, press the button once again.

8 Tabs

Enable you to switch between items.

9 Close button

Closes the screen.

Selecting the output channel for each output port

NOTE

If PATCH CONFIRMATION in the PREFERENCE tab on the USER SETUP screen is ON, a

confirmation dialog box will appear when you attempt to change the patch settings. If STEAL

PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to

change a location that is already patched elsewhere.

3 54

1

9

6

7

2

8

STEP

1. In the Function Access Area, press the SETUP button.

2. Press the OUTPUT PORT button in the SYSTEM SETUP field located in the center of

the SETUP screen.

3. In the tabs below the OUTPUT PORT screen, select the output port you want to

control.

4. Press the channel select button of the port you want to operate.

5. Use the category select list and the channel select buttons to select the send-source

channel.

SETUP screen OUTPUT PORT screen

Input and output patching

Reference Manual

18

CH SELECT screen

1 Category select list

Select the category of the channel. The categories correspond to the following channels.

They vary depending on the output port type.

• MIX/MATRIX ................................ MIX1–MIX16, MATRIX1–MATRIX8

• ST/MONO/MONI/CUE ................. STEREO L, STEREO R, MONO(C), MONI L,

MONI R, MONI C, CUE L, CUE R, SMON L, SMON

R, SMON C, SMON LFE, SMON Ls, SMON Rs,

MMTX L, MMTX R, MMTX C, MMTX LFE, MMTX

Ls, MMTX Rs

• DIRECT OUT 1–32 ...................... CH1–CH32 Direct Outs

• DIRECT OUT 33–64 .................... CH33–CH64 Direct Outs

• INSERT 1 OUT 1–32 ................... CH1–CH32 Insert 1 Outs

• INSERT 1 OUT 33–64 ................. CH33–CH64 Insert 1 Outs

• INSERT 1 OUT MIX/MATRIX....... MIX1–MIX16, MATRIX1–MATRIX8 Insert 1 Outs

• INSERT 1 OUT ST/MONO........... STEREO L, STEREO R, MONO (C) Insert 1 Outs

• INSERT 2 OUT 1–32 ................... CH1–CH32 Insert 2 Outs

• INSERT 2 OUT 33–64 ................. CH33–CH64 Insert 2 Outs

• INSERT 2 OUT MIX/MATRIX....... MIX1–MIX16, MATRIX1–MATRIX8 Insert 2 Outs

• INSERT 2 OUT ST/MONO........... STEREO L, STEREO R, MONO (C) Insert 2 Outs

• CASCADE MIX/MATRIX.............. MIX1–MIX16, MATRIX1–MATRIX8

• CASCADE ST/MONO/CUE ......... STEREO L, STEREO R, MONO (C), CUE L,

CUE R

NOTE

In the case of QL1, channels that do not exist on the model will not be shown.

2 Channel select button

Select the channel to be assigned to the output port from the current category.

3 CLOSE button

Closes the screen.

Inserting an external device into a channel

You can insert an effect processor or other external device into the signal path of an INPUT,

MIX, MATRIX, STEREO, or MONO channel. When doing so, the type of input/output port

used for the insertion and the location of the insertion in/out can be specified individually for

each channel.

NOTE

If you install a digital I/O card in a slot and digitally connect an external device, you must

synchronize the word clock of the QL console and the external device (page 211).

1

2

3

STEP

1. Use the Bank Select keys in the Fader Bank section and the [SEL] keys on the top

panel to select the channel where you want to insert the external device.

2. Press the popup button in the INSERT field in the SELECTED CHANNEL VIEW screen.

3. Press the INSERT OUT or INSERT IN button.

4. Select an output port or an input port.

5. Press the INSERT ON button.

SELECTED CHANNEL VIEW screen INSERT/DIRECT OUT window (1ch)

Input and output patching

Reference Manual

19

INSERT/DIRECT OUT window (1ch)

 INSERT field

This field enables you to make insert settings. Press one of three fields to choose PRE HPF

(immediately before the HPF), PRE EQ (immediately before the EQ) or PRE FADER

(immediately before the fader), or POST ON (immediately after the [ON] key) as the insert

position.

1 INSERT OUT button

Displays the currently-selected output port for insert 1 and insert 2. Press this button to

open the PORT SELECT window, and select an output port.

2 INSERT IN button

Displays the currently-selected input port for insert 1 and insert 2. Press this button to

open the PORT SELECT window, in which you can select an input port.

3 INSERT ON/OFF button

Switches the insert on or off.

4 APPLY TO ALL INPUT button (input channels only)

Specifies whether the insert point/direct out point settings will be applied to all input

channels.

5 APPLY TO ALL OUTPUT button (output channels only)

Specifies whether the insert point setting will be applied to all output channels.

NOTE

Insert 1 and insert 2 are serial connections with fixed sequential numbers.

 INSERT IN HA field

This field will appear if you have selected an input port (that features a head amp) as the

insert-in.

6 +48V button

Switches head amp phantom power (+48V) (currently-selected for insert 1 and insert 2)

on or off.

7 A.GAIN knob

Indicates the currently-selected head amp analog gain setting for insert 1 and insert 2.

You can use the [TOUCH AND TURN] knob to adjust the gain.

NOTE

• If you have selected the INPUT jack on the QL console as

the input port for insert-in, make the HA settings in the

INSERT IN HA field.

• Even if the INSERT ON/OFF button is OFF, the signal

selected for insert-out will continue to be sent.

8 HA meter

Displays the level of the currently-selected head amp input signal for insert 1 and insert

2.

9 Close button

Closes the screen.

INSERT screen (8ch)

1 Channel select button

Selects the channel to set. The channel icon, color, and number appear.

9

8

77 663 9

5

1 42

3

4

3

2

1

4

Input and output patching

Reference Manual

20

2 INSERT ON/OFF button

Switches the insert on or off. The currently-specified insert point setting appears above

the button.

3 INSERT OUT button

Displays the currently-selected port for insert 1 and insert 2. Press this button to open

the PORT SELECT window, in which you can select an output port.

4 INSERT IN button

Displays the currently-selected port for insert 1 and insert 2. Press this button to open

the PORT SELECT window, in which you can select an input port. You can also view the

insert-in level by checking the indicator located to the right of this button.

PORT SELECT window

Displayed when you press either the INSERT OUT or INSERT IN button in the one-channel

or the eight-channel INSERT/DIRECT OUT window. Set the input/output port used for

insertion.

1 Category select list

Selects the category of port. The categories correspond to the following ports. The

displayed categories vary depending on the channel type.

• DANTE1–32........................... DANTE1–DANTE32

• DANTE33–64......................... DANTE33–DANTE64 (QL5 only)

• INPUT .................................... INPUT1–32 (QL5), INPUT1–16 (QL1) (input channels

only)

• OUTPUT/DIGITAL ................. OMNI OUT1–16, DIGITAL OUT L/R (output channels

only)

• SLOT1.................................... SLOT1(1)–SLOT1(16)

• SLOT2.................................... SLOT2(1)–SLOT2(16)

• GEQ RACK............................ GEQ1L(A)–GEQ8R(B)

• EFFECT RACK...................... FX1L(A)–FX8R(B)

• PREMIUM RACK................... PR1L(A)–PR8R(B)

2 Port select buttons

Assign the port that will be used as insert-out/insert-in for the currently-selected

channel.

NOTE

If a rack in which a GEQ, PEQ or Premium Rack is mounted is specified as the insert-out or

insert-in, the other patch point will automatically be assigned to the same rack. Also, insert mode

will automatically be switched on. Additionally, if you defeat the insert-out or insert-in of a rack in

which a GEQ, PEQ or Premium Rack is mounted, the other patch point will automatically be

defeated and at the same time insert mode will automatically be switched off.

3 CLOSE button

Closes the screen.

1

2

3

La page charge ...

Yamaha V3 Manuel utilisateur

Ce manuel convient également à

Yamaha V3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents