GE APHA14NYLB Guide d'installation

Marque: GE

Modèle: APHA14NYLB

Catégorie: Climatiseurs mobiles

Taper: Guide d'installation

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

Find these numbers on a label on

the side of the air conditioner.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

AND INSTALLATION

INSTRUCTIONS

AIR CONDITIONER

Portable Room

49-7820 02-18 GEA

APCA12

SAFETY INFORMATION .........3

USING THE AIR CONDITIONER

Controls ..............................5

CARE AND CLEANING

Air Filter ..............................7

INSTALLATION

INSTRUCTIONS ...................8

TROUBLESHOOTING TIPS ......12

WARRANTY ......................15

CONSUMER SUPPORT ..........16

2 49-7820

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-7820 3

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electrical shock, injury to persons, or damage when using the air conditioner,

follow basic precautions, including the following:

• Read all of the instructions before using this

appliance.

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Do not operate the air conditioner if it has a

damaged cord or plug, if it is not working properly, or

if it has been damaged or dropped.

• The air conditioner should be serviced only by

qualified service personnel. Call an authorized

service company for examination, repair, or

adjustment.

• Disconnect power before servicing.

• Disconnect power before cleaning.

NOTE: Turning off power by pressing the Power

button does NOT disconnect the appliance from the

power supply.

• Do not install or use the air conditioner in any area

where the atmosphere contains combustible gases

or where the atmosphere is contaminated. Avoid

any chemicals coming in contact with your air

conditioner.

• Do not store anything directly on top of the air

conditioner.

• Use two or more people to move and install air

conditioner.

• Never operate the air conditioner without the filters

in place.

• Do not use the air conditioner near a bathtub,

shower or wash basin or other wet area.

4 49-7820

Features and appearance will vary.

Lights next to the touch pads on the air conditioner control panel indicate the selected settings.

Controls

1. Power Control

The power control turns the unit on and off.

2. Timer

Auto Turn Off:

With machine in running mode, press timer button to

select number of hours you would like the unit to run

in air conditioning mode until it automatically shuts off.

Auto Turn On:

With machine in stand by mode, press timer button to

select number of hours until you would like the unit to

automatically start running in air conditioning mode.

3. Mode Control

The mode control has three settings: COOL, DRY,

and FAN. The settings are adjusted with Mode

Control button. A light will indicate which setting is

currently being used.

Cooling Mode.

When cool mode is selected, the indicator light turns

green. During the cooling mode the air is cooled and

hot air is exhausted to the outside through the exhaust

tube. Adjust fan speed and air temperature to suit

your desired comfort level. NOTE: The air exchange

hose must vent outside the room when using cool

mode.

Dry Mode - Dehumidification.

When dehumidify mode is selected, the indicator light

turns green. Air is dehumidified as it passes through

the unit, without being in full cooling mode. If room

temperature is higher than 77 degrees Fahrenheit, fan

speed can be adjusted; otherwise fan speed is fixed

to “Low”. NOTE: If the unit is to be used as a

dehumidifier, do not connect the exhaust hose let

the warm air return to the room. Continuous water

drainage is then necessary (see page 8).

Fan Mode

When fan mode is selected the indicator light will

shine green. Air is circulated throughout the room

with no cooling. NOTE: Unit does not need to be

vented in Fan mode.

4. Fan Speed Control

The Fan Speed Control has 3 settings: High, Low,

and Sleep.

5. Timer/Temp Set Controls

• Used for adjusting the timer and thermostat.

• The default display is room temperature.

• In cooling mode when + or - button is pressed, the

set temperature is displayed and may be adjusted.

After 10 seconds the display will revert back to room

temperature. Temperature is only adjustable in cool

mode. The time is adjustable between 1-24 hours.

NOTE: By pressing both + and - buttons at the

same time, the display will toggle between Celsius

and Fahrenheit. The temperature cannot be

adjusted in the fan or dehumidification modes.

6. Display

7. Warning Light

Condensed water may accumulate in the unit. If the

internal tank becomes full, the warning light will light

up and the unit will not operate until the unit has been

drained.

Air Conditioner Controls

USING THE AIR CONDITIONER

Controls

COOL

DRY

FAN

HIGH

LOW

SLEEP

POWER TIMER MODE FAN

FULL

1 2 3 4 5

7 6

49-7820 5

USING THE AIR CONDITIONER

Controls

Remote Control

Ŷ7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW

the signal receiver on the air conditioner.

Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG

the remote control that could block the signal.

Ŷ7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRIXSWR

feet.

Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\

as indicated on the remote control.

1. Power On/Off

2. Mode

Cool: LED lights when in cooling mode.

Dehumidification: LED lights when in dehumidification

mode.

Fan: LED lights when in fan mode.

3. Fan Speeds

Select between multiple fan speeds. Number of fan

speeds vary by model. In dehumidification mode, and

room temperature is greater than 77° F, fan speed can

be adjusted; Otherwise fan speed is fixed to “low”.

4. On/Off Timer

To set the timer for a 1- 24-hour delay until the air

conditioner turns off:

1. When you use the timer setting button while the unit

is operating, you can preset a time for the unit to turn off.

2. When you use the timer setting button while the unit

is on standby, you can preset a time for the unit to turn

on.

3. If you press the “ON/OFF” button, the preset timer

function will be canceled.

4. Timer setting range is 1-24 hours.

To clear Timer Delay program:

NOTE: Air conditioner can be either on or off.

1. Press the Timer Button.

2. Press the + or - buttons continuously till “00”

appears to cancel the timer function.

To change the remaining time (in hours):

1. Press the Timer Button.

2. Press the plus or minus button to change the delay

time from 1 to 24 hours.

3. The new delay time will display.

5. Setting the Temperature

7RVHWWKHWHPSHUDWXUHSUHVVWKHޕRUޔNH\VWR

raise or lower the temperature. The temperature can be

raised or lowered in the cool mode. The temperature

cannot be adjusted in fan or dehumidification mode.

NOTE; The temperature can be set between 61° F to

89° F (Cool Mode)..

6 49-7820

USING THE AIR CONDITIONER

Controls

Cool Mode

Use the COOL mode for cooling.

To set the COOL mode:

1. Press the MODE pad until the COOL indicator light is

lit.

2. Press the FAN pad to set HIGH, LOW, or SLEEP fan

speed.

3. Press + or - to set the desired temperature between

61°F and 89°F in 1°F increments.

After settings have been made, the display will change

back to show the room temperature.

The temperature control is used to maintain the room

temperature. The compressor will cycle on and off

to keep the room at the set level of comfort. Set the

temperature control at a lower number and the indoor

air will become cooler. Set the temperature control at a

higher number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on

while set to COOL, it will take approximately 3 minutes

for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling—Select the COOL mode and

HIGH or LOW fan speed with a middle set temperature.

For Maximum Cooling—Select the COOL mode

and HIGH fan speed with a lower set temperature.

For Quieter & Nighttime Cooling—Select the

COOL mode and SLEEP fan speed with a middle set

temperature.

NOTE: If you switch from COOL or DRY mode setting to

OFF wait 3 minutes before restarting.

DRY Mode—Dehumidification

Use the DRY mode to provide dehumidification only.

The fan will run at a fixed speed at this setting, so a fan

speed cannot be set. Keep windows and doors closed

for the best dehumidifying effects.

To set the DRY mode:

•Press the MODE pad until the DRY indicator light is lit.

In the DRY mode, a set temperature will not be

displayed. After DRY mode has been set, the display will

change back to show the room temperature.

NOTE: If you switch from a DRY setting to OFF or to a

fan setting, wait at least 3 minutes before switching back

to a DRY setting.

If using the unit in the DRY mode as a dehumidifier for

an extended time.

1 . Unplug the power cord.

2. Connect a drain hose (not included) to the bottom

drain port (see page 10, lower drain #7) and lead

hose to floor drain.

3. Reconnect the power cord and press the MODE pad

until the DRY indicator light is lit.

FAN Mode

Use the FAN mode to provide air circulation and filtering

without cooling.

To set the FAN mode:

• Press the FAN pad until the desired indicator light for

HIGH, LOW, or SLEEP fan speed is lit.

Since fan only settings do not provide cooling, a set

temperature will not be displayed. After FAN speed has

been set, the display will change back to show the room

temperature.

Power Outage Recovery Feature

In the case of a power outage or interruption, the unit will

automatically re-start in the settings last used after the

power is restored.

NOTE: If the TIMER was set before the power outage, it

will need to be reset after power is restored.

The display will always default to show the room temperature.

When the air conditioner is turned on, it will automatically start in the last mode and fan settings selected.

49-7820 7

USING THE AIR CONDITIONER

Controls

Air Conditioner Use

IMPORTANT: If the air conditioner has been tilted on its

side, wait 24 hours before turning on the air conditioner

to allow the oil to return to the compressor. This will

prevent the air conditioner from failing prematurely.

• Allow 20” (51 cm) of space around the unit for proper

air circulation.

• Do Not operate the air conditioner without air filters in

place.

• Do not spill liquid on the control panel; it may cause

an electrical short to the interior electronic parts that

would either disable them or cause them to function

improperly.

• When turning on the air conditioner for the first time

after plugging it into an electrical outlet, the unit will

start in Cooling mode set at 75ºF (24°C), and at High

fan speed. The control panel will display the current

room temperature.

• When turning on the unit after previous use, it will

remember the last settings used.

• After a normal shut down, please wait for 3 minutes

before restarting the unit.

• In Cooling mode, this unit should not require water

to be removed. This model has a unique design that

continuously evaporates the water.

• When the unit is operated in high humidity conditions,

you may need to empty the water tank periodically.

• The unit will shut down automatically when the water

tank is full. The Water Full indicator illuminates to alert

you of this condition.

8 49-7820

CARE AND CLEANING

Care and Cleaning

Air Filter

The air filters should be cleaned at least once a week for

your unit to operate at optimum efficiency.

CAUTION

DO NOT operate the air conditioner

without a filter because dirt and lint will clog it and

reduce performance.

To remove:

1. Unplug or disconnect power.

2. Pull to remove upper filter panel (item #9 shown on

page 10).

3. Wash or vacuum the dust from the air filters.

NOTE: If washed, gently shake the filter to remove the

excess water and dust particles trapped in the filter.

4. Reinstall the filters.

5. Plug in or reconnect power.

CLEANING

1. Unplug or disconnect power.

2. Use only a soft cloth dampened with water to clean

the cabinet.

NOTE:

•Do not use a liquid or spray cleaner to clean the air

conditioner.

•DO NOT use chemicals, abrasives, ammonia,

chlorine bleach, concentrated detergents, solvents or

scouring pads. Some of these chemicals/items may

damage and/or discolor your air conditioner.

3. Dry thoroughly with a soft cloth.

4. Plug in or reconnect power.

Internal Water Tank

The Water Full indicator illuminates, when the internal

water tank has filled with condensed water.

To Empty the Internal Water Tank:

1. Unplug or disconnect power.

2. Place a shallow 1 quart or larger pan (not included)

below the lower drain located on the back (near the

bottom) of the air conditioner.

3. Remove the cap and the rubber plug and drain the

water tank.

4. Re-insert the drain plug and screw the cap snugly into

place.

5. Plug in or reconnect power.

How to Insert the Batteries in the Remote Control

1. Remove the battery cover by sliding it according to the

arrow direction.

2. Insert new batteries, making sure that the (+) and (–)

of battery are installed correctly.

3. Reattach the cover by sliding it back into position.

NOTES:

Ŷ8VH³$$$´YROWDONDOLQHEDWWHULHV'RQRWXVH

rechargeable batteries.

Ŷ5HPRYHWKHEDWWHULHVIURPWKHUHPRWHFRQWUROLIWKH

system is not going to be used for a long time.

Ŷ'RQRWPL[ROGDQGQHZEDWWHULHV'RQRWPL[DONDOLQH

standard (carbon-zinc) or rechargeable (ni-cad, ni-mh,

etc) batteries.

WARNING

Electrical Shock Hazard

Disconnect power before cleaning.

Failure to do so can result in death or electrical

shock.

Storage

If the unit is not being used for a long period of time:

To Empty the Internal Water Tank:

1. Unplug or disconnect power.

2. Drain the water from the water tank. (See “Internal

Water Tank section” above.)

3. Use the original packaging to repack the unit to avoid

a buildup of dust or dirt.

4. Store the air conditioner in a cool, dry location.

49-7820 9

INSTALLATION INSTRUCTIONS

Installation Instructions

Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com.

In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save these instructions for

local inspector’s use.

• IMPORTANT — Observe all governing codes

and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Approximately 1 hour

• We recommend that two people install this product.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

• You MUST use all supplied parts and use proper

installation procedures as described in these

instructions when installing this air conditioner.

ELECTRICAL REQUIREMENTS

Some models require a 115/120-volt AC,

60-Hz grounded outlet protected with a

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility

of electric shock hazard. If the wall outlet you plan to

use is only a 2-prong outlet, it is your responsibility

to have it replaced with a properly grounded 3-prong

wall outlet.

CAUTION

Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord.

Do not change the plug on the power cord of this air

conditioner.

Aluminium house wiring may present special

problems—consult a qualified electrician.

Power cord includes a current interrupter device. A

test and reset button is provided on the plug case. The

device should be tested on a periodic basis by first

pressing the TEST button and then the RESET button

while plugged into the outlet. If the TEST button does

not trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and contact a

qualified service technician.

10 49-7820

INSTALLATION INSTRUCTIONS

Installation Instructions

PARTS INCLUDED

(Appearance may vary)

Exhaust Hose

Hose Connector

Cover #5

Window Panel and

Extension Panel (3)

1. Air Outlet

2. Control Panel

3. Handle

4. Air Inlet

5. Air Exhaust

6. Caster

7. Power Cord

8. Lower Drain

NOTE: Please ensure if the water outlet drain

is securely installed before use.

9. Filter Panel

Foam Seals

49-7820 11

INSTALLATION INSTRUCTIONS

Installation Instructions

1. LOCATION REQUIREMENTS

• Place the air conditioner on a flat, level surface

in a location that is at least 20” (51 cm) from any

wall.

NOTE: The recommended distance from the

window for optimal performance is 31.5 (80 cm).

• Maintain a minimum 20” (51 cm) clearance

around the air conditioner to not block airflow.

• Keep the air conditioner free of any obstructions

such as drapes, curtains, blinds, etc.

• The exhaust hose should be free of any

obstructions.

• Do not place the air conditioner on an unstable

or raised surface because it could fall and cause

damage or injury.

• Do not place the air conditioner in direct

sunlight or near a heat source such as

baseboard heaters, stoves, etc.

• The window panel can be installed in a window

with a minimum 20” (51 cm) to a maximum 46”

(117 cm) opening.

2. UNPACK AIR CONDITIONER

• Remove packaging materials. Save the carton and

the foam packaging for storing the air conditioner

when not in use.

NOTE: There are NO packing materials inside the air

conditioner to remove—Do Not open the cabinet.

• Properly dispose of/recycle all packing material.

• Handle the air conditioner gently.

• Keep the air conditioner upright and level. Do

not set the air conditioner on its side, front, back

or upside down.

WARNING

Excessive Weight Hazard

Use two or more people to move and install air

conditioner.

Failure to do so can result in back or other injury.

3. INSTALL EXHAUST

A. Connect the connectors #2 and #3 to two

sides of exhaust hose #1 to create an

exhaust assembly.

B. Sliding in one end of hose assembly (with

hose connector #2) to rear panel.

Then push the knob to fix the hose assembly

firmly.

12 49-7820

INSTALLATION INSTRUCTIONS

Installation Instructions

4. INSTALL WINDOW PANELS

A. Insert the window panel B and C to each

end of the main panel A. Adjust to fix the

length of window

B. Open the window and place window panels

into window. Adjust the extension panels

to fit width or height of window by the screw

and nut sets mounted on the main panel A.

C. Apply foam seals provided to top, bottom,

and ends of the window panel to provide

best air seal.

CA B

5. ATTACH EXHAUST HOSE TO THE

EXHAUST NOZZLE

• Insert the other end of the exhaust hose

assembly (with hose connector #3) onto the

window bracket.

Indoor

6. COMPLETE INSTALLATION

A. Plug the power cord into a grounded 3 prong

outlet.

B. Press the Reset button on the power cord to

ensure the safety plug is providing power to

the air conditioner.

C. Allow 20” of space around the unit for proper

air circulation.

B. When removing the portable air conditioner

for storage, the window panel may be left in

place. Simply place the cover (#5) over the

hole on the window panel.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove the ground prong from the

power cord plug.

Do not use an adapter.

Do not use an extension cord.

Failure to do so can result in death, fire or

electrical shock.

49-7820 13

TROUBLESHOOTING TIPS

Troubleshooting Tips

PROBLEM POSSIBLE CAUSE(S) SOLUTION

Unit does not start or

operate

Power supply cord is not plugged into an

outlet.

Plug the power cord into a grounded 3 prong

outlet.

Power supply cord has tripped. Press and release the RESET button on the power

supply cord.

The Power button has not been pressed. Press the Power button on the Control Panel or

Remote Control to turn ON the air conditioner.

There is no power to the electrical outlet. Plug a working lamp into the outlet to check for

power.

A household fuse has blown or a circuit

breaker has tripped.

Replace the fuse or reset the circuit breaker.

The control was programmed for a Time

Delay.

Cancel the Time Delay. See “Control Panel.”

The batteries in the remote control are

dead.

Replace the batteries.

The internal water tank is full.

NOTE: The air conditioner automatically

turns off, and the Water Full indicator

illuminates to alert you of this condition.

Empty the water tank. See “Air Conditioner

Care.”

Remote control is not

working

Batteries are dead. Replace the batteries.

Batteries are installed incorrectly. Make sure the batteries are inserted in the correct

position.

Air conditioner is

working but the room

is not cooling.

The room temperature is hot.

NOTE: On extremely hot and humid

days,the air conditioner will take longer to

cool the room.

Allow time for the room to cool when you first turn

on the unit.

Make sure the air conditioner has an adequate

BTU rating for the size of the room being cooled.

The control is set incorrectly to Fan or

Dehum mode.

Set the Mode to Cool and the Fan Speed to High.

Airflow is restricted. Remove any obstacles to the airflow and redirect

airflow for uniform cooling.

Temperature set too high. Lower the set temperature.

Air filters are dirty or restricted. Clean the air filter. See “Air Conditioner Care.”

Air conditioner installed incorrectly Check the exhaust hose and window panel for

proper installation.

Doors and windows are open. Close the doors and windows to the room being

cooled to prevent cooled air from escaping.

14 49-7820

Notes

NOTES

49-7820 15

WARRANTY

Warranty

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

EXCLUSION OF IMPLIED WARRANTIES - Your sole and exclusive remedy is product repair as provided in this Limited

àäõõäñ÷üÊñüìðóïìèçúäõõäñ÷ìèöìñæïøçìñê÷ëèìðóïìèçúäõõäñ÷ìèöòéðèõæëäñ÷äåìïì÷üòõĤ÷ñèööéòõäóäõ÷ìæøïäõ

purpose, are limited to one year or the shortest period allowed by law.

For US Customers: This warranty is extended to the original purchaser and any succeeding owner for products purchased

for home use within the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is

not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE

Appliances Service location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you

öóèæìĤæïèêäïõìêë÷öäñçüòøðäüäïöòëäùèò÷ëèõõìêë÷öúëìæëùäõüéõòðö÷ä÷è÷òö÷ä÷èÝòîñòúúëä÷üòøõïèêäïõìêë÷öäõè

æòñöøï÷üòøõïòæäïòõö÷ä÷èæòñöøðèõäģäìõöòĦæèòõüòøõö÷ä÷èđöÊ÷÷òõñèüÐèñèõäï

Warrantor US:

GE Appliances, a Haier company

Ŷ Customer instruction. This owner’s manual provides

information regarding operating instructions and user

controls.

Ŷ Improper installation. If you have an installation problem,

or if the air conditioner is of improper capacity, contact

your dealer or installer. You are responsible for providing

adequate electrical connecting facilities.

Ŷ Failure of the product resulting from modifications to the

product or due to unreasonable use including failure to

provide reasonable and necessary maintenance.

Ŷ Replacement of house fuses or resetting of circuit

breakers.

Ŷ Failure due to corrosion on models not corrosion-

protected.

Ŷ Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Ŷ Incidental or consequential damage caused by possible

defects with this air conditioner.

Ŷ Damage caused after delivery.

What Will Not Cover:

For The Period Of: Will Replace:

One Year

From the date of the

original purchase

Replacement, repair, or refund of the original retail price for any product which fails due

to a defect in materials or workmanship. If the unit is exchanged, the replacement unit

ìöúäõõäñ÷èçéòõ÷ëèõèðäìñçèõòéüòøõóõòçøæ÷đöòõìêìñäïòñè¡üèäõúäõõäñ÷üóèõìòçÐÎ

will, at its sole discretion, replace the product with a product of the same or comparable

functionality and quality or refund the original retail price.

Ŷ Properly pack your unit. We recommend using the original

carton and packing materials.

ŶReturn the product to the retail location where it was

purchased.

Ŷ Include in the package a copy of the sales receipt or other

evidence of date of original purchase. Also print your

name and address and a description of the defect.

In Order to Make a Warranty Claim During the First 90 Days from the Date of Original Purchase:

Ŷ Locate your original sales receipt and make a note of your

model and serial number.

Ŷ Call 1.877.337.3639 (in the United States) to initiate

the product replacement process. In Canada, call

1.877.470.9174.

ŶYou will be asked to provide your name, address, date of

purchase, model and serial number.

ŶGE Appliances will arrange for a carton to be sent to your

home to recover the product.

Ŷ Ùïèäöèõè÷øõñäïïõèôøèö÷èçðä÷èõìäïö¤óòö÷äêèóõè¡óäìç¥

in the carton provided. Please include a description of the

defect.

ŶYou should receive your replacement product or refund

within 7 to 10 business days after your package is

received.

In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:

16 49-7820

Printed in China

Consumer Support

CONSUMER SUPPORT

GE Appliances Website

Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day

of the year! You can also shop for more great GE Appliances products and take advantage of all our on-line support

services designed for your convenience. In the US: GEAppliances.com

communication and prompt service under the terms of your warranty, should the need arise. You may also mail in

the pre-printed registration card included in the packing material. In the US: GEAppliances.com/register

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

In the US: GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since improper

servicing may cause unsafe operation.

If you are not satisfied with the service you receive from GE Appliances, contact us on our Website with all the

details including your phone number, or write to:

In the US: General Manager, Customer Relations | GE Appliances, Appliance Park | Louisville, KY 40225

GEAppliances.com/ge/service-and-support/contact.htm

49-7820 02-18 GEA

APCA12

ACCONDICIONADORES DE AIRE

PARA SALA

Escriba los números de modelo

y serie aquí:

# de Modelo _____________

# de Serie _______________

Puede encontrar estos números

en una etiqueta en el costado

del acondicionador de aire.

GE es una marca registrada de General Electric Company. Fabricado bajo licencia de marca.

MANUAL DEL

PROPIETARIO Y

INSTRUCCIONES

DE INSTALACIÓN

INSTRUCCIONES

DE SEGURIDAD

...................3

USO DEL ACONDICIONADOR

DE AIRE

Controle ..............................5

CUIDADO Y LIMPIEZA

Filtro de aire ..........................7

INSTRUCCIONES

DE INSTALACIÓN ................8

SOLUCIONAR PROBLEMAS ....12

GARANTÍA .......................15

SERVICIO AL CONSUMIDOR ...16

2 49-7820

GRACIAS POR HACER QUE GE APPLIANCES SEA PARTE DE SU HOGAR.

Ya sea que haya crecido usando GE Appliances, o que ésta es su primera vez, nos complace

tenerlo en la familia.

Sentimos orgullo por el nivel de arte, innovación y diseño de cada uno de los electrodomésticos de

GE Appliances, y creemos que usted también. Entre otras cosas, el registro de su electrodoméstico

asegura que podamos entregarle información importante del producto y detalles de la garantía

cuando los necesite.

Registre su electrodoméstico GE ahora a través de Internet. Sitios Web y números telefónicos útiles

están disponibles en la sección de Soporte para el Consumidor de este Manual del Propietario.

También puede enviar una carta en la tarjeta de inscripción preimpresa que se incluye con

el material embalado.

49-7820 3

INSTRUCCIONES IMPORTANTES

DE SEGURIDAD

ADVERTENCIA: Para reducir el riesgo de incendio, choque eléctrico, lesiones a personas o daños al utilizar el

acondicionador de aire, siga precauciones básicas, incluyendo las siguientes:

•Lea todas las instrucciones antes de usar este

electrodoméstico.

•Conecte a un contacto de pared de conexión a tierra de

3 terminales.

•No quite el terminal de conexión a tierra.

•No use un adaptador.

•No use un cable eléctrico de extensión.

•No ponga a funcionar el acondicionador de aire si

tiene un cable o enchufe dañado, si no funciona

correctamente o si se ha dañado o caído.

•El acondicionador de aire solo debe ser reparado

por personal de servicio competente. Llame a la

compañía de servicio técnico autorizada para su

inspección, reparación o ajuste.

•Desconecte el suministro de energía antes de darle

servicio técnico.

•Desconecte el suministro de energía antes de limpiarlo..

NOTA: Si apaga la unidad presionando el botón

Power (Encendido), esto NO desconecta el

electrodoméstico del suministro de energía.

•No instale ni utilice el acondicionador de aire en áreas

donde la atmósfera contenga gases combustibles

o donde la atmósfera esté contaminada. Evite que

cualquier producto químico entre en contacto con el

acondicionador de aire.

•No almacene nada directamente encima del

acondicionador de aire.

•Con la ayuda de dos o más personas, mueva e instale el

acondicionador de aire.

•Nunca haga funcionar el acondicionador de aire si los

Ĥï÷õòöçèäìõèñòèö÷Źñæòïòæäçòöèñöøïøêäõ

•No utilice el acondicionado de aire cerca de una tina,

ducha o lavabo ni otra zona húmeda.

INFORMACIÓN DE SEGURIDAD

INFORMACIÓN IMPORTANTE DE SEGURIDAD

LEA TODAS LAS INSTRUCCIONES ANTES DE USAR

LEA Y GUARDE ESTAS INSTRUCCIONES

4 49-7820

Las luces al lado de las teclas de toque en el panel de control del acondicionador de aire indicarán los ajustes

seleccionados. Las funciones y el aspecto pueden variar.

BOTONES

1. Control del encendido

El control del encendido enciende y apaga la unidad.

2. Temporizador

Apagado Automático:

Con el motor en el modo de funcionamiento, presione el

botón del temporizador para seleccionar la cantidad de

horas que desea que la unidad funcione en el modo de

acondicionador de aire hasta que se apague de forma

automática.

Encendido Automático:

Con el motor en el modo de espera, presione el botón del

temporizador para seleccionar la cantidad de horas que

desea que pasen hasta que la unidad comience a funcionar

de forma automática en el modo de acondicionador de aire.

3. Control de Modo

El control de modo posee tres configuraciones: COOL

(Refrigeración), DRY (Seco), y FAN (Ventilación). Las

configuraciones son ajustadas con el botón Mode Control

(Control de Modo). Una luz indicará qué configuración está

siendo usada actualmente.

Modo de Refrigeración

Cuando el modo de refrigeración sea seleccionado, la

luz indicadora cambiará a verde. Durante el modo de

refrigeración, el aire es enfriado y el aire caliente es

extraído hacia afuera a través de las tuberías del extractor.

Ajuste la velocidad del ventilador y la temperatura del aire

hasta el nivel de confort deseado. NOTA: La manguera de

intercambio de aire deberá ventilar hacia afuera de la

sala al usar el modo de refrigeración.

Modo Seco - Deshumidificación

Cuando el modo de deshumidificación sea seleccionado, la

luz indicadora cambiará a verde. El aire es deshumidificado

al pasar a través de la unidad, sin estar en el modo de

refrigeración total. Si la temperatura del ambiente es

superior a 77 grados Fahrenheit, la velocidad del ventilador

podrá ser ajustada; de otro modo la velocidad del ventilador

es ajustada en “Low” (Bajo). NOTA: Si la unidad será

usada como deshumidificador, no conecte la manguera

del extractor; permita que el aire caliente regrese a

la sala. El drenaje de agua continuo será entonces

necesario (consulte la página 8).

Modo de Ventilación

Cuando el modo de ventilación sea seleccionado, la

luz indicadora brillará de color verde. El aire circulará a

través de toda la sala sin refrigeración. NOTA: No es

necesario que la unidad sea ventilada en el modo Fan

(Ventilación).

4. Control de Velocidad del Ventilador

El Control de Velocidad del Ventilador cuenta con 3

configuraciones: High (Alto), Low (Bajo), y Sleep (Inactivo).

5. Controles de Configuración del Temporizador/

Temperatura

• Se usan para ajustar el temporizador y el termostato.

• La pantalla por omisión es la temperatura del ambiente.

• Cuando el botón + o – sea presionado en el modo de

refrigeración, la temperatura configurada será exhibida

y podrá ser ajustada. Luego de 10 segundos, la pantalla

regresará a la temperatura del ambiente. La temperatura

sólo podrá ser ajustada en el modo de refrigeración. La hora

podrá ser ajustada entre 1 y 24 horas.

NOTA: Al presionar los Botones + y - al mismo tiempo,

la pantalla alternará entre Celsius y Fahrenheit. La

temperatura no podrá ser ajustada en los modos de

ventilación o deshumidificación.

6. Pantalla

7. Luz de Advertencia

Se podrá acumular agua condensada en la unidad. Si el

tanque interno se llena, la luz de advertencia se iluminará

y la unidad no funcionará hasta que la misma haya sido

drenada.

Controles del acondicionador de aire

USO DEL ACONDICIONADOR DE AIRE

Controles

COOL

DRY

FAN

HIGH

LOW

SLEEP

POWER TIMER MODE FAN

FULL

1 2 3 4 5

7 6

La page charge ...

GE APHA14NYLB Guide d'installation

Marque: GE

Modèle: APHA14NYLB

Catégorie: Climatiseurs mobiles

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

italiano: GE APHA14NYLB Guida d'installazione
English: GE APHA14NYLB Installation guide
español: GE APHA14NYLB Guía de instalación

GE APHA14NYLB Guide d'installation

GE APHA14NYLB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents