Harmonic ProView 7000 3.6 Guide d'installation

Marque: Harmonic

Modèle: ProView 7000 3.6

Taper: Guide d'installation

Ce manuel convient également à

ProView 7000 3.5

ProView

7000

RELEASE 3.6

Installation Guide

Rev A

Manual Part No. MAN-PVR-7000-3.6 REV-A

November 2014

service marks of Harmonic Inc. in the United States and other countries. Dolby, Dolby Digital, Dolby Digital Plus and Dolby E are registered trademarks of

Dolby Laboratories. Implementations of AAC and HE-AAC by Fraunhofer IIS. Other company, product and service names mentioned herein may be

trademarks or service marks of their respective owners. All product and application features and specifications are subject to change at Harmonic’s sole

discretion at any time and without notice.

Disclaimer

Harmonic reserves the right to alter the equipment specifications and descriptions in this publication without prior notice. No part of this publication shall be

deemed to be part of any contract or warranty unless specifically incorporated by reference into such contract or warranty. The information contained herein

is merely descriptive in nature, and does not constitute a binding offer for sale of the product described herein. Harmonic assumes no responsibility or

liability arising from the use of the products described herein, except as expressly agreed to in writing by Harmonic. The use and purchase of this product do

not convey a license under any patent rights, copyrights, trademark rights, or any intellectual property rights of Harmonic. Nothing hereunder constitutes a

representation or warranty that using any products in the manner described herein will not infringe any patents of third parties.

Third-Party Product Trademarks

Adobe® After Effects®, Photoshop®, Flash® Professional, Premiere®

Avid® Media Composer®

Dolby® E, Dolby Digital, Dolby Digital Plus

Jünger Audio™

Apple® QuickTime®

Microsoft® Mediaroom®

Microsoft® PlayReady®

DOCSIS® 3.0

Start Over® TV

Third-Party Copyright Notes

Dolby is a registered trademark of Dolby Laboratories. Dolby Digital, Dolby Digital Plus, Dolby Pulse, aacPlus, AC-3, and Dolby E are trademarks of Dolby

Laboratories.

Level Magic and Jünger are trademarks of Jünger Audio Studiotechnik GmbH.

MPEG Audio technology licensed from Fraunhofer IIS http://www.iis.fraunhofer.de/amm/

PitchBlue® is a registered trademark of Vigor Systems.

QuickTime and the QuickTime logo are trademarks or registered trademarks of Apple Computer, Inc., used under license therefrom.

Trademark Acknowledgments

Harmonic and all Harmonic product names are trademarks of Harmonic Inc. All other trademarks are the property of their respective owners.

The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in

accordance with the terms of those agreements.

May be covered by one or more of U.S. Patents No. 6,571,351; 6,696,996; 6,545,721; 6,574,225; 6,895,003; 6,522,649; 6,643,702; foreign counterparts

and pending patent applications.

This system is distributed with certain other software that may require disclosure or distribution of licenses, copyright notices, conditions of use, disclaimers

and/or other matter. Use of this system or otherwise fulfilling their conditions constitutes your acceptance of them, as necessary. Copies of such licenses,

notices, conditions, disclaimers and/or other matter are available in any one of the following locations: the LEGAL NOTICES AND LICENSES directory of the

distribution disk of the software, the root directory of the hard disk drive of the Products, or by contacting us at support@harmonicinc.com.

Notice

Information contained in this guide is subject to change without notice or obligation. While every effort has been made to ensure that the information is

accurate as of the publication date, Harmonic Inc. assumes no liability for errors or omissions. In addition, Harmonic Inc. assumes no responsibility for

damages resulting from the use of this guide.

License Agreement and Limited Warranty

1. AGREEMENT: This is a legal agreement ("Agreement") between you ("you" or "your") and Harmonic, or its appropriate local affiliate ("Harmonic", "we",

"us" or "our"). Use of our product(s) and any updates thereto purchased or validly obtained by you (the "Products"), and/or the Software (as defined below)

(collectively, the "System"), constitutes your acceptance of this Agreement. "Use" includes opening or breaking the seal on the packet containing this

Agreement, installing or downloading the Software as defined below or using the Software preloaded or embedded in your System. As used herein, the term

"Software" means the Harmonic owned software and/or firmware used in or with the Products and embedded into, provided with or loaded onto the

Products in object code format, but does not include, and this Agreement does not address, any third-party or free or open source software separately

licensed to you ("Third Party Software"). If you do not agree to this Agreement, you shall promptly return the System with a dated receipt to the seller for a

full refund.

2. LICENSE: Subject to the terms and conditions of this Agreement (including payment), we hereby grant you a nonexclusive, nontransferable license to use

the object code version of the Software embedded into, provided solely for use with or loaded onto the Product, and the accompanying documentation

("Documentation") for your internal business purposes. The Software and any authorized copies are owned by us or our suppliers, and are protected by law,

including without limitation the copyright laws and treaties of the U.S.A. and other countries. Evaluation versions of the Software may be subject to a time-

limited license key.

3. RESTRICTIONS: You (and your employees and contractors) shall not attempt to reverse engineer, disassemble, modify, translate, create derivative works

of, rent, lease (including use on a timesharing, applications service provider, service bureau or similar basis), loan, distribute, sublicense or otherwise transfer

the System, in whole or part except to the extent otherwise permitted by law. The Software may be operated on a network only if and as permitted by its

Documentation. You may make one (1) back up copy of the object code of the Software for archival purposes only. Evaluation Software will be run in a lab,

nonproductive environment. Results of any benchmark or other performance tests may not be disclosed to any third party without our prior written consent.

Title to and ownership of the Software and Documentation, and all copyright, patent, trade secret, trademark, and other intellectual property rights in the

System, shall remain our or our licensors' property. You shall not remove or alter any copyright or other proprietary rights notice on the System. We reserve

all rights not expressly granted.

4. LIMITED WARRANTY: (a) Limited Warranty. We warrant to you that, commencing on your receipt of a Product and terminating 1 year thereafter, the System

will perform substantially in accordance with its then-current appropriate Documentation. The Product (including replacements) may consist of new, used or

previously-installed components. (b) Remedies. If the System fails to comply with such warranty during such period, as your sole remedy, you must return

the same in compliance with our product return policy, and we shall, at our option, repair or replace the System, provide a workaround, or refund the fees you

paid. Replacement Systems are warranted for the original System's remaining warranty period. (c) Exclusions. EVALUATION SOFTWWARE IS LICENSED ON

AS-IS BASIS AND SUBJECT TO 4(d). We will have no obligation under this limited warranty due to: (i) negligence, misuse or abuse of the System, such as

unusual physical or electrical stress, misuse or accidents; (ii) use of the System other than in accordance with the Documentation; (iii) modifications,

alterations or repairs to the System made by a party other than us or our representative; (iv) the combination, operation or use of the System with equipment,

devices, software or data not supplied by us; (v) any third party hardware or Third Party Software, whether or not provided by us; (vi) any failure other than by

us to comply with handling, operating, environmental, storage or maintenance requirements for the System in the Documentation, including, without

limitation, temperature or humidity ranges. (d) Disclaimers. We are not responsible for your software, firmware, information, or data contained in, stored on,

or integrated with any Product returned to us for repair or replacement. SUCH LIMITED WARRANTY IS IN LIEU OF, AND WE SPECIFICALLY DISCLAIM, ANY

AND ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF

SATISFACTORY QUALITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT. WE DO NOT WARRANT THAT THE

SYSTEM WILL MEET YOUR REQUIREMENTS OR BE UNINTERRUPTED OR ERROR-FREE. NO ADVICE OR INFORMATION, WHETHER ORAL OR WRITTEN,

OBTAINED FROM US OR ELSEWHERE, WILL CREATE ANY WARRANTY NOT EXPRESSLY STATED IN THIS AGREEMENT. Some jurisdictions do not allow the

exclusion of implied warranties or limitations on how long an implied warranty may last, so such exclusions may not apply to you. In that event, such implied

warranties or limitations are limited to 60 days from the date you purchased the System or the shortest period permitted by applicable law, if longer. This

warranty gives you specific legal rights and you may have other rights which vary from state to state or country to country.

5. LIMITATION OF LIABILITY: WE AND OUR AFFILIATES, SUPPLIERS, LICENSORS, OR SALES CHANNELS ("REPRESENTATIVES") SHALL NOT BE LIABLE TO

YOU FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR EXEMPLARY DAMAGES OF ANY KIND, INCLUDING BUT NOT LIMITED TO LOST

REVENUES, PROFITS OR SAVINGS, OR THE COST OF SUBSTITUTE GOODS, HOWEVER CAUSED, UNDER CONTRACT, TORT, BREACH OF WARRANTY,

NEGLIGENCE, OR OTHERWISE, EVEN IF WE WERE ADVISED OF THE POSSIBILITY OF SUCH LOSS OR DAMAGES. NOTWITHSTANDING ANY OTHER

PROVISIONS OF THIS AGREEMENT, WE AND OUR REPRESENTATIVES' TOTAL LIABILITY TO YOU ARISING FROM OR RELATING TO THIS AGREEMENT

OR THE SYSTEM SHALL BE LIMITED TO THE TOTAL PAYMENTS TO US UNDER THIS AGREEMENT FOR THE SYSTEM. THE FOREGOING LIMITATIONS

SHALL NOT APPLY TO DEATH OR PERSONAL INJURY TO PERSONS OR TANGIBLE PROPERTY IN ANY JURISDICTION WHERE APPLICABLE LAW

PROHIBITS SUCH LIMITATION. YOU ARE SOLELY RESPONSIBLE FOR BACKING UP YOUR DATA AND FILES, AND HEREBY RELEASE US AND OUR

REPRESENTATIVES FROM ANY LIABILITY OR DAMAGES DUE TO THE LOSS OF ANY SUCH DATA OR FILES. SOME JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO SUCH EXCLUSIONS MAY NOT APPLY TO YOU.

6. CONFIDENTIALITY: Information in the System and the associated media, as well as the structure, organization and code of the Software, are proprietary to

us and contain valuable trade secrets developed or acquired at great expense to us or our suppliers. You shall not disclose to others or utilize any such

information except as expressly provided herein, except for information (i) lawfully received by the user from a third party which is not subject to

confidentiality obligations; (ii) generally available to the public without breach of this Agreement; (iii) lawfully known to the user prior to its receipt of the

System; or (iv) required by law to be disclosed.

7. SUPPORT: Updates, upgrades, fixes, maintenance or support for the System (an "Upgrade") after the limited warranty period may be available at separate

terms and fees from us. Any Upgrades shall be subject to this Agreement, except for additional or inconsistent terms we specify. Upgrades do not extend the

limited warranty period.

8. TERM; TERMINATION: The term of this Agreement shall continue unless terminated in accordance with this Section. We may terminate this Agreement at

any time upon default by you of the license provisions of this Agreement, or any other material default by you of this Agreement not cured with thirty (30)

days after written notice thereof. You may terminate this Agreement any time by terminating use of the System. Except for the first sentence of Section 2

("License") and for Section 4(a) ("Limited Warranty"), all provisions of this Agreement shall survive termination of this Agreement. Upon any such termination,

you shall certify in writing such termination and non-use to us.

9. EXPORT CONTROL: You agree that the Products and Software will not be shipped, transferred, or exported into any country or used in any manner

prohibited by the United States Export Administration Act or any other export laws, restrictions, or regulations (the "Export Laws"). You will indemnify, defend

and hold us harmless from any and all claims arising therefrom or relating thereto. In addition, if the Products or Software are identified as export controlled

items under the Export Laws, you represent and warrant that you are not a citizen, or otherwise located within, an embargoed nation (including without

limitation Iran, Iraq, Syria, Sudan, Libya, Cuba, North Korea, and Serbia) and that you are not otherwise prohibited under the Export Laws from receiving the

Software. All rights to the Products and Software are granted on condition that such rights are forfeited if you fail to comply with the terms of this Agreement.

10. U.S. GOVERNMENT RIGHTS: The Software and the documentation which accompanies the Software are "Commercial Items," as that term is defined at

48 C.F.R. §2.101, consisting of "Commercial Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R.

§12.212 or 48 C.F.R. §227.7202, as applicable. Consistent with 48 C.F.R. §12.212 or 48 C.F.R. §§227.7202-1 through 227.7202-4, as applicable, the

Commercial Computer Software and Commercial Computer Software Documentation are being licensed to U.S. Government as end users (a) only as

Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein. Harmonic, 4300 North

First Street, San Jose, CA 95134 U.S.A.

11. GENERAL: You shall not assign, delegate or sublicense your rights or obligations under this Agreement, by operation of law or otherwise, without our

prior written consent, and any attempt without such consent shall be void. Subject to the preceding sentence, this Agreement binds and benefits permitted

successors and assigns. This Agreement is governed by California law, without regard to its conflicts of law principles. The U.N. Convention on Contracts for

the International Sale of Goods is disclaimed. If any claim arises out of this Agreement, the parties hereby submit to the exclusive jurisdiction and venue of

the federal and state courts located in Santa Clara County, California. In addition to any other rights or remedies, we shall be entitled to injunctive and other

equitable relief, without posting bond or other security, to prevent any material breach of this Agreement. We may change the terms, conditions and pricing

relating to the future licensing of our Systems and other intellectual property rights, including this Agreement, from time to time. No waiver will be implied

from conduct or failure to enforce rights nor effective unless in a writing signed on behalf of the party against whom the waiver is asserted. If any part of this

Agreement is found unenforceable, the remaining parts will be enforced to the maximum extent permitted. There are no third-party beneficiaries to this

Agreement. We are not bound by additional and/or conflicting provisions in any order, acceptance, or other correspondence unless we expressly agree in

writing. This Agreement is the complete and exclusive statement of agreement between the parties as to its subject matter and supersedes all proposals or

prior agreements, verbal or written, advertising, representations or communications concerning the System.

Every reasonable attempt has been made to comply with all licensing requirements for all components used in the system. Any oversight is unintentional and

will be remedied if brought to the attention of Harmonic at support@harmonicinc.com.

Documentation Conventions

This guide may use some special symbols and fonts to call your attention to important information. The following symbols appear throughout this guide:

DANGER: The Danger symbol calls your attention to information that, if ignored, can cause physical harm to

you.

CAUTION: The Caution symbol calls your attention to information that, if ignored, can adversely affect

the performance of your Harmonic product, or that can make a procedure needlessly difficult.

LASER DANGER: The Laser symbol and the Danger alert call your attention to information about the lasers in

this product that, if ignored, can cause physical harm to you.

NOTE: The Note symbol calls your attention to additional information that you will benefit from heeding. It

may be used to call attention to an especially important piece of information you need, or it may provide

additional information that applies in only some carefully delineated circumstances.

IMPORTANT: The Important symbol calls your attention to information that should stand out when you are

reading product details and procedural information.

TIP: The Tip symbol calls your attention to parenthetical information that is not necessary for performing a

given procedure, but which, if followed, might make the procedure or its subsequent steps easier, smoother, or

more efficient.

In addition to these symbols, this guide may use the following text conventions:

NOTE: You require Adobe Reader or Adobe Acrobat version 6.0 or later to open the PDF files. You can download

Adobe Reader free of charge from www.adobe.com.

Convention Explanation

Typed Command Indicates the text that you type in at the keyboard

prompt.

<Ctrl>, <Ctrl>+<Shift> A key or key sequence to press.

Links The italics in blue text to indicate Cross-references, and

hyperlinked cross-references in online documents.

Bold Indicates a button to click, or a menu item to select.

ScreenOutput The text that is displayed on a computer screen.

Emphasis The italics text used for emphasis and document

references.

Table of Contents

Chapter 1: ProView™ 7000 Installation Guide .............................................6

Inventory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Earthing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Power Supply to the Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing the Unit in a Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Fitting the Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing the L Shape Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Mounting ProView 7000 units in the 19" Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Electrical Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Connecting the Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Switching On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Appendix A: Contacting the Technical Assistance Center.........................11

Appendix B: Safety and Regulatory Compliance Information...................13

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Safety Symbols & Translated Safety, Warning & Caution Instructions (English) . . . . . . . . . 13

Symboles de sécurité et traduits de sécurité, d'avertissement et Attention Instructions

(français) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht Anleitung (Deutsch) . 19

Site Preparation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Product End-of-Life Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Product Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Safety Rules (English) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Règles de sécurité (French) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

EU Manufacturer’s Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Electromagnetic Compatibility Notices – Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Product Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Product Regulatory Compliance Markings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Product Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

EU RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

EU REACH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Other RoHS and REACH type Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Waste Electrical and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Battery Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

WEEE Take-Back Request Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Compliance with additional country specific environmental, safety and EMC standards: 33

Chapter 1

ProView™ 7000 Installation Guide

Topics:

InventoryCheck

Earthing

PowerSupplytotheUnit

InstallingtheUnitinaRack

ElectricalPowerConnection

ConnectingtheCables

SwitchingOn

Inventory Check

Beforeinstallation,ensurethatalltheequipmentandtheattachedpartsareavailableand

undamaged,accordingtothefollowinglist:

Table 1: Inventory

Item Quantity

ProView 7000/7100 Unit 1

Power cable 1

CAUTION: If anything is missing or damaged, do not continue with the installation and report to your

Harmonic support representative.

Earthing

Theunitmustbeconnectedtoearthbeforeanyothercablesareconnectedanditshouldremain

permanentlyconnectedtoprotectedearth.Cable18AWGshouldbeused.Whentheunitisrack‐

mounted,thedevice’searthstudmustbeconnectedtotherackhousing,whichmustbecorrectly

earthed.Whenremovingcablestheearthmustberemovedlast.

Grounding jack screw

Figure 2: AC Connector

Chapter 1 ProView™ 7000 Installation Guide

Power Supply to the Unit

Toensurecorrectandsafeoperationoftheunit,ensurethefollowing:

Ensurethataqualifiedelectricianhasinstalledthemainpowersupplyinaccordancewith

powerauthorityregulations.Makesureallpoweringmustbewiredwithanearthleakage,

accordingtolocalregulations.

Whentheunitisrack‐mounted,ensurethattherackiscorrectlygrounded.

DANGER: To avoid electrocution, ensure that the rack has been correctly grounded before switching on the

ProView 7000 device. When removing the unit, remove the grounded connection only after the unit is switched

off and unplugged.

Installing the Unit in a Rack

Forrackinstallation,ensurethatadesignated19"rackisfullypreparedforinstallation.Ensure

sufficientspacebehindtherackforeasyaccessforinstallationandmaintenance.Rackmounting

requirestheuseofLshapeslides,availablefromHarmonic.Theamountofunitsinstalledina

rackisafunctionoftheunits’powerconsumptionandheatdissipation.AddressHarmonic

supportforcalculatingthemaximumloadontherack.

ThefollowingsectionsdetailtheinstallationofaProView7000unitina19"rackusingmounting

slides.

Fitting the Brackets

Tofitthebrackets:

1. Fitapairofbracketstobothsiderailsoftherackhousingwithtwoflatwasherscrewson

eachside.Usethetwofrontholesatthesidesofthehousingtoattachthebrackets.

(Complementingnutsarealreadyinstalledontheinnersideoftheholes,thefourscrews

requiredarenotincludedinthesuppliedkit).

2. Ensurepropergroundingoftherackassemblytopreventpotentialelectricalproblems.

Installing the L Shape Slides

TheProView7000usesforcedairventilation,evacuatingtheairouttheleftsideofthe19"rack.

Toensuresmoothairflow,Lshapeslidesareprovidedforrackmounting.

TofittheLshapeslides:

1. Ensurethatthebracketsarefastenedwithappropriatescrewstoeachsideofthechassis’

rails.

2. FitLshapeslidestothefittedbracketsandfastenwithfourscrews(notincluded).

Chapter 1 ProView™ 7000 Installation Guide

Installing the Unit in a Rack

Mounting ProView 7000 units in the 19" Rack

DANGER: To prevent bodily injury when mounting or servicing this unit in a rack, you must take special

precautions to ensure that the system remains stable. The following guidelines are provided to ensure your

safety:

Thisunitshouldbemountedatthebottomoftherackifitistheonlyunitintherack.

Iftherackwillholdanumberofunits,loadtherackfromthebottomtothetopwiththe

heaviestcomponentatthebottomoftherack.

Iftherackisprovidedwithstabilizingdevices,installthestabilizersbeforemountingor

servicingtheunitintherack.

ATTENTION: Pour éviter toute blessure corporelle pendant les opérations de montage ou de réparation de

cette unité en casier, il convient de prendre des précautions spéciales afin de maintenir la stabilité du système.

Les directives ci-dessous sont destinées à assurer la protection du personnel.

Sicetteunitéconstituelaseuleunitémontéeencasier,elledoitêtreplacéedanslebas.

Sicetteunitéestmontéedansuncasierpartiellementrempli,chargerlecasierdebasenhaut

enplaçantl’élémentlepluslourddanslebas.

Silecasierestéquipédedispositifsstabilisateurs,installerlesstabilisateursavantdemonterou

deréparerl'unitéencasier.

WARNUNG: Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser Einheit in einem

Gestell müssen sie besondere Vorkehrungen treffen, um sicherzustellen, daß das System stabil bleibt. Die

folgenden Richtlinien sollen zur Gewährleistung Ihrer Sicherheit dienen.

WenndieseEinheitdieeinzigeimGestellist,solltesieuntenimGestellangebrachtwerden.

BeiAnbringungdieserEinheitineinemzumTeilgefülltenGestellistdasGestellvonuntennach

obenzuladen,wobeidasschwersteBauteiluntenimGestellanzubringenist.

WirddasGestellmitStabilisierungszubehörgeliefert,sindzuerstdieStabilisatorenzu

installieren,bevorsiedieEinheitimGestellanbringenodersiewarten.

CAUTION: Ensure that a sufficient amount of airflow enters the ProView 7000 from the left end (from the

front panel point of view) .

Consider if other devices in the rack use airflow in the opposite direction.

Consider that the amount of units installed per rack is a function of power requirements and heat dissipation.

Address Harmonic support for calculating the maximum load on the rack.

Tomountthe19"/42UrackwiththeProView7000units:

1. MountProView7000unitsingroupsofnomorethanfiveunitsoneachpairofbrackets.

2. Leaveone‐unit‐spacebetweeneachgroupoffiveunits.

Chapter 1 ProView™ 7000 Installation Guide

Electrical Power Connection

TheProView7000ispoweredbyanACpowersupply.

DANGER: To avoid electrocution ensure that the rack has been correctly grounded before

switching on the unit. When removing the unit remove the grounding connection only after the

unit is switched off and unplugged.

VORSICHT! Zur Vermeidung von lebensgefährlichem Stromschlag muss vor Einschalten des Geräts

sichergestellt werden, dass das Rack vorschriftsmäßig geerdet wurde. Bei Entnahme des Geräts ist dieses

zuerst auszuschalten und von der Stromversorgung zu trennen, bevor der Erdungsanschluss entfernt wird.

DANGER: Pour éviter l’électrocution, assurez-vous que le rack a bien été mis à la terre avant de mettre

l’unité en marche. Lors du retrait de l’unité, retirer le raccordement de terre seulement après avoir mis

l’unité à l’arrêt et l’avoir débranchée.

CAUTION: This product relies on the building’s electrical installation for short-circuit (overcurrent)

protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 20 A U.S. (240 VAC, 20 A

international) is used on the phase conductors (all current-carrying conductors).

ATTENTION: Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de

l’installation électrique du local. Vérifier qu’un fusible ou qu’un disjoncteur de 120 V alt., 20 A U.S. maximum

(240 V alt., 20 A international) est utilisé sur les conducteurs de phase (conducteurs de charge).

WARNUNG: Dieses Produkt ist darauf angewiesen, daß im Gebäude ein Kurzschluß-bzw. Überstromschutz

installiert ist. Stellen sie sicher, daß eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V

Wechselstrom, 20 A (bzw. in den USA 120 V Wechselstrom, 20 A) an den Phasenleitern (allen stromführenden

Leitern) verwendet wird.

Connecting the Cables

AllProView7000connectorsarelocatedontherearpanel.Connectthefollowing:

InputCables

IfyouareusingDVB‐S/S2,connectthesatellitecabletotheRFINconnector.Ifyouareusing

ASI,connecttheASIcablestotheconnectorsmarkedASIIN.

ManagementLANCable

ConnectthemanagementLANcabletotheManagementport.

VideoOutput

Connectanoutputdestinationtooneoftheoutputconnectorsontheoutputinterface.

VideoMonitor

Connectavideomonitor,forlocalmonitoringoftheoutput,toeithertheCVMONortheHDMI

port.

Chapter 1 ProView™ 7000 Installation Guide

Switching On

BeforeswitchingtheProView7000on,makesurethatallcablesarecorrectlyconnected.Ensure

thattheunitisconnectedtothemainpowersupplyandcorrectlygrounded.

Switchtheunitonwiththerearpowerswitch.

Oncethebootprocessiscompleted(after2‐3minutes)theStatusOKmessagedisplayson

thefrontpanelLCD.

No Service Selected

Figure 3: Front panel startup display

Status OK

Appendix A

Contacting the Technical Assistance Center

Harmonic Global Service and Support has many Technical Assistance Centers (TAC) located

globally, but virtually co-located where our customers can obtain technical assistance or request

on-site visits from the Regional Field Service Management team. The TAC operates a Follow-The-

Sun support model to provide Global Technical Support anytime, anywhere, through a single case

management and virtual telephone system. Depending on time of day, anywhere in the world, we

will receive and address your calls or emails in one of our global support centers. The Follow-the-

Sun model greatly benefits our customers by providing continuous problem resolution and

escalation of issues around the clock.

Table A–1: For Distribution and Delivery (D&D, Legacy Harmonic) Products

Region Telephone Technical Support E-mail

Americas 888.673.4896 (888.MPEG.TWO)

or 408.490.6477 [email protected]m

EME +44.1252.555.450 [email protected]

India +44.1252.555.450 support.emea@harmonicinc.com

Russia +7.495.926.4608 support.sm@harmonicinc.com

Africa +44.1252.555.450 [email protected]

Mainland China +86.10.6569.5580 [email protected]

Japan +81.3.5565.6737 [email protected]

Asia Pacific – Other

Territories +65.6542.0050 apacsu[email protected]

Table A–2: For Production and Playout (P&P, Legacy Omneon and Rhozet) Products

Region Telephone Technical Support E-mail

Americas 888.673.4896 (888.MPEG.TWO)

or 408.490.6477 [email protected]

EMEA +44.1252.555.450 omneonemeasupport@harmonicinc.com

Mainland China +86.10.6569.5580 [email protected]

Japan +81.3.5565.6737 [email protected]

Asia Pacific – Other

Territories +65.6542.0050 apacsupport@harmonicinc.com

Appendix A Contacting the Technical Assistance

Center

The Harmonic Inc. support website is:

http://www.harmonicinc.com/content/technical-support

The Harmonic Inc. Distribution and Delivery product software downloads site is:

ftp://ftp.harmonicinc.com

The Harmonic Inc. Playout and Production software downloads site is:

ftp://ftp.Omneon.com//Updates/Omneon/Current/

The Harmonic Inc. corporate address is:

Harmonic Inc.

4300 North First St.

San Jose, CA 95134, U.S.A.

Attn: Customer Support

The corporate telephone numbers for Harmonic Inc. are:

Tel. 1.800.788.1330 (from the U.S. and Canada)

Tel. +1.408.542.2500 (outside the U.S. and Canada)

Fax.+1.408.542.2511

Appendix B

Safety and Regulatory Compliance Information

Legal Disclaimer: Information in this document is provided in connection with Harmonic

products. Unless otherwise agreed in writing Harmonic products are not designed nor intended

for any application in which the failure of the product could cause personal injury or death.

NOTE:

The information in this appendix may apply to purchased products only.

Important Safety Instructions

This section provides important safety guidelines for operators and service personnel.

Specific

warnings and cautions are found throughout the guide where they apply, but may not

appear

here. Please read and follow the important safety information, noting especially those

instructions

related to risk of fire, electric shock or injury to persons. You must adhere to the guidelines in this

document to ensure and maintain compliance with existing product certifications and approvals.

In this document, we use “product,” “equipment,” and “unit” interchangeably.

This equipment generates, uses, and can radiate radio frequency energy. It may cause harmful

interference to radio communications if it is not installed and used in accordance with the

instructions in this manual. Operation of this equipment in a residential area is likely to cause

harmful interference If this occurs, the user will be required to correct the interference at his or

her own expense.

In event of conflict between the information in this document and information provided with the

product or on our website for a particular product, this product documentation takes precedence.

Safety Symbols & Translated Safety, Warning & Caution Instructions

(English)

To avoid personal injury or property damage, before you begin installing or replacing the product,

read, observe, and adhere to all the following safety instructions and information. Harmonic

products and/or product packaging may be marked with the safety symbols used throughout this

document, when it is necessary to alert operators, users, and service providers to pertinent safety

instructions in the manuals.

Appendix B Safety and Regulatory Compliance

Information

Safety Symbols & Translated Safety, Warning & Caution Instructions (English)

Mark Notes

Warning

Installing or Replacing the Product Unit Warning

Only trained and qualified service personnel should be allowed to install,

replace, or service this unit (refer AS/NZS 3260 Clause 1.2.14.3 Service

Personnel).

Read the installation instructions before connecting the system to the

power source.

When installing or replacing the unit, always make the ground connection

first and disconnect it last.

Installation of the unit must comply with local and national electrical

codes.

This unit is intended for installation in restricted access areas. A restricted

access area can be accessed only through the use of special tool, lock

and key or other means of security.

Use only specified replacement parts.

Do not use this unit in or near water. Disconnect all AC power before

installing any options or servicing the unit unless instructed to do so by

this manual.

Warning

Rack Mount Warning

To prevent bodily injury when mounting or servicing this unit in a rack,

special precautions must be taken to ensure your safety and stability of

system:

Conform to local occupational health and safety requirements when

moving and lifting the equipment.

Ensure that mounting of the unit by mechanical loading tools should not

induce hazardous conditions.

To avoid risk of potential electric shock, a proper safety ground must be

implemented for the rack and each piece of equipment installed on it.

Warning

Chassis Warning

Before connecting or disconnecting ground or power wires to the chassis,

ensure that power is removed from the DC circuit.

To prevent personal injury or damage to the chassis, lift the unit only by

using handles that are an integral part of the chassis, or by holding the

chassis underneath its lower edge.

Any instructions in this guide that require opening the chassis or removing

a board should be performed by qualified service personnel only.

Slots and openings in the chassis are provided for ventilation. Do not

block them. Leave the back of the frame clear for air exhaust cooling and

to allow room for cabling - a minimum of 6 inches (15.24 cm) of clearance

is recommended.

Appendix B Safety and Regulatory Compliance

Information

Safety Symbols & Translated Safety, Warning & Caution Instructions (English)

Warning

Electric Shock Warning

This unit might have more than one power cord. To reduce the risk of

electric shock, disconnect the two power supply cords before servicing

the unit.

Before working on a chassis or working near power supplies, unplug the

power cord on AC units.

Do not work on the system or connect or disconnect cables during

periods of lightning activity.

This unit is grounded through the power cord grounding conductor. To

avoid electric shock, plug the power cord into a properly wired receptacle

before connecting the product input or outputs.

Route power cords and other cables so that they are not likely to be

damaged. Disconnect power input to unit before cleaning. Do not use

liquid or aerosol cleaners; use only a damp cloth to clean chassis.

Dangerous voltages exist at several points in this product. To avoid

personal injury, do not touch exposed connections and components while

power is on. Do not insert anything into either of the system's two power

supply cavities with power connected

Never install an AC power module and a DC power module in the same

chassis.

Do not wear hand jewelry or watch when troubleshooting high current

circuits, such as the power supplies.

To avoid fire hazard, use only the specified correct type voltage and

current ratings as referenced in the appropriate parts list for this unit.

Always refer fuse replacement to qualified service personnel.

This unit relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that a fuse or circuit breaker no larger than 120 VAC,

15A U.S. (240 VAC, 10A international) is used on the phase conductors

(all current-carrying conductors).

To avoid electrocution ensure that the rack has been correctly grounded

before switching on the unit. When removing the unit remove the

grounding connection only after the unit is switched off and unplugged.

Caution

Electrostatic Discharge (ESD) Caution

Follow static precaution at all times when handling this unit.

Always wear an ESD-preventive wrist or ankle strap when handling

electronic components. Connect one end of the strap to an ESD jack or

an unpainted metal component on the system

Handle cards by the faceplates and edges only; avoid touching the

printed circuit board and connector pins.

Place any removed component on an antistatic surface or in a static

shielding bag.

Avoid contact between the cards and clothing.

Periodically check the resistance value of the antistatic strap.

Recommended value is between 1 and 10 mega-ohms (Mohms).

Mark Notes

Appendix B Safety and Regulatory Compliance

Information

Symboles de sécurité et traduits de sécurité, d'avertissement et Attention Instructions

(français)

Symboles de sécurité et traduits de sécurité, d'avertissement et

Attention Instructions (français)

Pour éviter des blessures ou des dommages matériels, avant de commencer l'installation ou le

remplacement du produit, lire, observer, et de respecter toutes les instructions et informations de

sécurité suivantes. Produits harmoniques et / ou l'emballage du produit peuvent être marqués

avec les symboles de sécurité utilisés dans le présent document, lorsque cela est nécessaire

pour alerter les opérateurs, les utilisateurs et les fournisseurs de services de consignes de

sécurité pertinentes dans les manuels.

Warning

Laser Radiation Warning

Invisible laser radiation may be emitted from disconnected fibers or

connectors. Do not stare into beams or view directly with optical instruments.

Never operate a unit with a broken fibre or with a separated fiber connector.

Warning

Lithium Battery Handling Safety Instructions

CALIFORNIA PERCHLORATE ADVISORY: Some lithium batteries may

contain perchlorate material. The following advisory is provided:

"Perchlorate Material - special handling may apply, see: www.dtsc.ca.gov/

hazardous waste/perchlorate/ for information".

Caution

Risk of explosion if battery is replaced incorrectly or with an incorrect type

Dispose of used batteries according to the manufacturer's instructions

There are no user-serviceable batteries inside Harmonic products. Refer

to Harmonic qualified personnel only to service the replaceable batteries

Mark Notes

Appendix B Safety and Regulatory Compliance

Information

Symboles de sécurité et traduits de sécurité, d'avertissement et Attention Instructions

(français)

Mark Notes

Avertissement

Installation ou remplacement de l'unité de produit Avertissement

Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualifiés et

expérimentés. (voir AS / NZS 3260 article 1.2.14.3 du personnel de

service).

Avant de brancher le système sur la source d'alimentation, consulter les

directives d'installation.

Lors de l'installation ou le remplacement de l'appareil, la mise à la terre

doit toujours être connectée en premier et déconnectée en dernier.

L'équipement doit être installé conformément aux normes électriques

nationales et locales.

Cet appareil est à installer dans des zones d'accès réservé. Ces dernières

sont des zones auxquelles seul le personnel de service peut accéder en

utilisant un outil spécial, un mécanisme de verrouillage et une clé, ou tout

autre moyen de sécurité.

Utilisez uniquement des pièces de rechange spécifiées.

Ne pas utiliser ce produit dans l'eau ni à proximité de l'eau. Débrancher

toutes les prises d'alimentation secteur avant d'installer des options ou

d'effectuer l'entretien de l'unité, à moins d'instructions contraires dans le

présent manuel.

Avertissement

Rack Monture Avertissement

Pour éviter les blessures corporelles lors du montage ou l'entretien de cet

appareil dans un rack, des précautions particulières doivent être prises pour

assurer votre sécurité et la stabilité du système:

Conformez-vous aux exigences de médecine du travail et de sécurité

lorsque vous déplacez et soulevez le matériel.

Assurez-vous que le montage de l'appareil par des outils de chargement

mécaniques ne doit pas induire des conditions dangereuses.

Pour éviter tout risque d'électrocution, le rack et chaque élément de

l'équipement installé dans le rack doivent être correctement reliés à la

terre.

Avertissement

Châssis Avertissement

Avant de connecter ou de déconnecter les câbles d'alimentation (pôles et

terre) du châssis, vérifiez que le circuit de courant continu est hors

tension.

Pour éviter toute blessure ou des dommages au châssis, soulevez l'unité

uniquement par les poignées du châssis lui-même ou en portant celui-ci

par le bord inférieur.

Toutes les opérations du présent guide nécessitant l'ouverture du châssis

ou le retrait d'une carte doivent être uniquement effectuées par du

personnel d'entretien qualifié.

Le châssis est muni de fentes et d'ouvertures d'aération. Ne pas les

bloquer. Dégager l'arrière du cadre pour permettre le refroidissement de

l'évacuation d'air et laisser de la place au câblage; un dégagement d'au

moins 15.24 cm (6 po) est recommandé.

Appendix B Safety and Regulatory Compliance

Information

Symboles de sécurité et traduits de sécurité, d'avertissement et Attention Instructions

(français)

Avertissement

Choc électrique Avertissement

Il est possible que cette unité soit munie de plusieurs cordons

d'alimentation. Pour éviter les risques d'électrocution, débrancher les

deux cordons d'alimentation avant de réparer l'unité.

Avant de travailler sur un châssis ou à proximité d'une alimentation

électrique, débrancher le cordon d'alimentation des unités en courant

alternatif.

Ne pas travailler sur le système ni brancher ou débrancher les câbles

pendant un orage.

Ce unité est mis à la terre par le conducteur de protection intégré au

cordon d'alimentation. Pour éviter les chocs électriques, brancher le

cordon d'alimentation dans une prise correctement cable avant de

raccorder les entrées ou sorties du unité.

Installer les cordons d'alimentation et autres cables de sorte qu'ils ne

risquent pas d'être endommagés. Couper l'alimentation avant nettoyage.

Ne pas utilizer de nettoyant liquide ou en aérosol; utiliser seulement un

linge humide.

Des courants électriques dangereux circulent dans cet appareil. Afin

d'éviter les lessures, ne pas toucher les connexions et composants

exposés lorsque l'appareil est sous tension. Ne rien insérer dans l'une ou

l'autre des cavités des prises de courant du système lorsque l'appareil est

sous tension.

N'installez jamais un module d'alimentation AC et un module

d'alimentation DC dans le même châssis.

Ne pas porter de bijoux aux mains ni de montre durant le dépannage des

circuits à haute tension, comme les transformateurs.

Pour prévenir les risques d'incendie, n'utiliser que le type, la tension et le

courant nominal spécifiés dans la nomenclature des pièces de ce unité.

Toujours confier le remplacement des fusibles à du personnel d'entretien

qualifié.

Pour ce qui est de la protection contre les courts-circuits (surtension), ce

produit dépend de l'installation électrique du local. Vérifier qu'un fusible

ou qu'un disjoncteur de 120 V alt., 15 A U.S. maximum (240 V alt., 10 A

international) est utilisé sur les conducteurs de phase (conducteurs de

charge).

Pour éviter l'électrocution, assurez-vous que le rack a bien été mis à la

terre avant de mettre l'unité en marche. Lors du retrait de l'unité, retirer le

raccordement de terre seulement après avoir mis l'unité à l'arrêt et l'avoir

débranchée.

Mark Notes

Appendix B Safety and Regulatory Compliance

Information

Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht Anleitung (Deutsch)

Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht

Anleitung (Deutsch)

Um Verletzungen oder Sachschäden zu vermeiden, bevor Sie mit der Installation oder Austausch

des Produkts zu beginnen, zu lesen, zu beobachten, und sich an all den folgenden

Sicherheitshinweise und Informationen. Harmonic Produkte und / oder Produktverpackungen

können mit den Sicherheitssymbole in diesem Dokument verwendet werden, markiert, wenn es

notwendig ist für die Betreiber, Anwender und Dienstleister, um relevante

Sicherheitsanweisungen in den Handbüchern zu alarmieren.

Attention

Les décharges électrostatiques (ESD) Attention

Respecter systématiquement les precautions relatives aux charges

électrostatiques durant la manipulation de cet unité.

Portez toujours un poignet ou la cheville bracelet antistatique préventive

lors de la manipulation des composants électroniques. Branchez une

extrémité de la sangle à une prise ESD ou d'un composant métallique non

peinte sur le système.

Manipulez les cartes en les faces avant et les bords seulement; éviter de

toucher la carte de circuit imprimé et les broches du connecteur.

Placer un composant retiré sur une surface antistatique ou dans un sac de

protection statique.

Éviter tout contact entre les cartes et les vêtements.

Vérifier périodiquement la valeur de résistance de la sangle antistatique.

Valeur recommandée est comprise entre 1 et 10 méga-ohms (Mohms).

Avertissement

Rayonnement laser Attention

Rayonnement laser invisible peut être émis à partir de fibres ou les

connecteurs débranchés. Ne pas regarder en faisceaux ou regarder

directement avec des instruments optiques. Ne jamais faire fonctionner

une unité en cas de bris d'une fibre ou de séparation d'un connecteur de

fibre.

Avertissement

Batterie au lithium Manipulation instructions de sécurité

Perchlorate pour la Californie Consultatif: Certaines batteries au lithium,

peuvent contenir du perchlorate. le texte qui suit consultatif est prévu:

"Présence de perchlorate - une manipulation spéciale peut s'appliquer,

voir: www.dtsc.ca.gov/hazardous waste/perchlorate/ for information".

Attention

Il y a danger d'explosion si la batterie est remplacée de manière

incorrecte ou par une batterie de type incorrect.

Mettre au rebut les batteries usagees conformement aux instructions du

fabricant.

Les batteries des produits Harmonic ne peuvent pas être réparées ni

entretenues par l'utilisateur. Ne confier l'entretien des batteries

remplaçables qu'à du personnel compétent de Harmonic.

Mark Notes

Appendix B Safety and Regulatory Compliance

Information

Sicherheit Symbole und übersetzt Sicherheit, Achtung & Vorsicht Anleitung (Deutsch)

Mark Notes

Warnung

Installation oder den Austausch des Produkts Einheit Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur

geschultem, qualifiziertem Personal gestattet warden (siehe AS / NZS

3260 Clause 1.2.14.3 Servicepersonal)

Lesen Sie die Installationsanweisungen, bevor Sie das System an die

Stromquelle anschließen.

Der Erdanschluß muß bei der Installation der Einheit immer zuerst

hergestellt und zuletzt abgetrennt werden.

Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt

vorgesehen. Ein Bereich mit beschränktem Zutritt ist ein Bereich, zu dem

nur Wartungspersonal mit einem Spezialwerkzeugs, Schloß und Schlüssel

oder anderer Sicherheitsvorkehrungen Zugang.

Verwenden Sie nur die angegebenen Ersatzteile

Das Gerät in oder in der Nähe von Wasser verwenden. Trennen Sie vor

der Installation von Optionen oder Wartung des Gerätes, es sei denn, dies

wurde von diesem Handbuch alle Netz.

Warnung

Rack-Montage-Warnung

Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser

Einheit in einem Gestell müssen Sie besondere Vorkehrungen treffen, um

sicherzustellen, daß das System stabil bleibt:

Entsprechen den lokalen Arbeitsschutzanforderungen beim Bewegen und

Heben der Ausrüstung.

Stellen Sie sicher, dass die Montage des Gerätes durch mechanische

Belastung Werkzeuge sollten nicht gefährlichen Bedingungen zu

induzieren.

Um das Risiko von möglichen elektrischen Schlag zu vermeiden, muss mit

einer angemessenen Erdung für Rack und jedes Gerät installiert ist

implementiert werden.

Warnung

Chassis Warnung

Gleichstrom-Unterbrechung Bevor Sie Erdungs- oder Stromkabel an das

Chassis anschließen oder von ihm abtrennen, ist sicherzustellen, daß der

Gleichstrom-Stromkreis unterbrochen ist.

Um Verletzungen und Beschädigung des Chassis zu vermeiden, sollten

Sie das Chassis nicht an den Henkeln auf den Elementen (wie z.B.

Stromanschlüsse, Kühlungen oder Karten) heben oder kippen; oder

indem Sie es unterhalb der Unterkante packen.

Alle Hinweise in diesem Handbuch, die das Öffnen benötigen Sie das

Gehäuse oder das Entfernen eines Board sollte nur von qualifiziertem

Fachpersonal durchgeführt werden.

Für Schlitze und Öffnungen im Chassis vorgesehen. Blockieren Sie sie

nicht. Lassen Sie die Rückseite des Rahmens frei für Abluftkühlung und

um Platz für die Verkabelung ermöglichen - ein Minimum von 6 Zoll

(15,24 cm) Abstand wird empfohlen

La page charge ...

Harmonic ProView 7000 3.6 Guide d'installation

Marque: Harmonic

Modèle: ProView 7000 3.6

Taper: Guide d'installation

Ce manuel convient également à

ProView 7000 3.5

Télécharger le PDF

rapport

dans d''autres langues

English: Harmonic ProView 7000 3.6 Installation guide
Deutsch: Harmonic ProView 7000 3.6 Installationsanleitung

Documents connexes

Autres documents

Inspur NF5180A6 Certification Manual