8Bitdo USB Wireless Adapter 2 Manuel utilisateur

USB Wireless Adapter 2
8Bitdo
Marque
8Bitdo
Modèle
USB Wireless Adapter 2
Taper
Manuel utilisateur
8BitDo USB Wireless Adapter 2
Instruction Manual
Controller Compatibility
Xbox Series X|S, Xbox One Bluetooth controllers
DualSense, DualShock 4, DualShock 3
Wii Remote, Wii U Pro, Switch Joy-Con, Switch Pro
8BitDo Bluetooth controllers and arcade sticks
* Bluetooth controllers supported only. 2.4g controllers are not supported.
* One adapter can connect to one controller at a time.
* Only one Joy-Con can be connected at a time, hold horizontally.
* Classic controller and Nunchuk are supported to be connected to the Wii Remote.
System Compatibility
Switch, Windows, Android, Raspberry Pi
PlayStation Classic, Genesis mini / Mega Drive mini, Retro Freak
* USB-C OTG cable is required to connect to Switch Lite.
* Android 4.0 or above, and OTG support are required on Android device.
Ultimate Software
It gives you elite control over every piece of your controller: customize button mapping, adjust
stick & trigger sensitivity, vibration control and create macros with any button combination.
* Please visit support.8bitdo.com for the application.
Support
Please visit support.8bitdo.com for further information & additional support.
FCC regulatory conformance：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B).
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme à la norme CAN ICES-003 (B)/NMB-003 (B)
.
Cet appareil contient des émetteurs / récepteurs exempt (s) de licence qui sont conformes
aux RSS exemptes de licence d'Innovation, Sciences et Développement économique Canada.
Son fonctionnement est soumis aux deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de
provoquer un fonctionnement indésirable de l'appareil.
RF Exposure
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment.
Cet équipement est conforme aux limites d'exposition aux radiations de la IC définies pour
un environnement non contrôlé.
  • Page 1 1
  • Page 2 2
  • Page 3 3

8Bitdo USB Wireless Adapter 2 Manuel utilisateur

USB Wireless Adapter 2
8Bitdo
Marque
8Bitdo
Modèle
USB Wireless Adapter 2
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents