Lumination LVR Series LED Volumetric Retrofit Kit Guide d'installation

Marque: Lumination

Modèle: LVR Series LED Volumetric Retrofit Kit

Taper: Guide d'installation

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 1 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Installation Guide

IND405

Lumination® LED Luminaire

LED Volumetric Retrot Kit

(LVR Series)

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING/AVERTISSEMENT

RISK OF FIRE OR ELECTRIC SHOCK

• Luminaire wiring and electrical parts may be damaged

when drilling for installation of LED retrot kit. Check for

enclosed wiring and components.

• LED Retrot Kit installation requires knowledge of

luminaires electrical systems. If not qualied, do not

attempt installation. Contact a qualied electrician.

• Install this kit only in luminaires that have the construction

features and dimensions shown in the photographs and/

or drawings and where the input rating of the retrot kit

does not exceed the input rating of the luminaire.

• To prevent wiring damage or abrasion, do not expose

wiring to edges of sheet metal or other sharp objects.

• Do not make or alter any open holes in an enclosure of

wiring or electrical components during kit installation.

• Suitable for damp locations.

RISQUE D’INCENDIE OU D’ELECTROCUTION

• Le câblage du luminaire ainsi que ses composantes électriques peuvent être

endommagés lors du perçage requis pour l’installation de l’ensemble de mise à

niveau à DEL. Vériez le câblage et les composants.

• L’installation de l’ensemble de mise à niveau à DEL requiert des connaissances en

système électrique d’éclairage. Si vous n’avez pas les qualications adéquates, ne

procédez pas à l’installation et contactez un électricien qualié.

• N’installez cet ensemble de mise à niveau à DEL que sur des luminaires ayant

une construction et des dimensions indiquées sur les photos et dessins et ce,

seulement dans la mesure où les spécications d’entrées de l’ensemble de mise à

niveau à DEL n’excède pas les spécications d’entrée du Luminaires dans lequel il

sera installé.

• An de prévenir tout dommage ou abrasion aux ls électriques, évitez que ceux-ci

ne viennent en contact avec les bordures métalliques ou d’autres ojets pointus.

• Ne laissez aucune ouverture dans le boitier ou le compartiment où se trouvent les

composants électriques.

• Convenient aux emplacements humides.

Save These Instructions

These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency to be

met in connection with installation, operation or maintenance. Should further information be desired or should particular problem arise

which are not covered suciently for the purchaser’s purpose, the matter should be referred to General Electric Company. GE Lighting

does not claim liability for any installation not performed according to this guide or not by a qualied electrician.

• Retrot kit may fall down if not installed properly, follow installation

instructions.

• This device is not intended for use with Emergency Exits.

For Your Safety

Read and observe all CAUTIONS and WARNINGS shown throughout these instructions. Use this product only in the manner intended

by the manufacturer. If there are any questions or concerns, contact the manufacturer.

CAUTION ATTENTION

• L’ensemble de mise à niveau à DEL peut tomber s’il n’est pas installé

correctement. Suivre les instructions d’installation.

• Cet appareil n’est pas conçu pour utilisation avec sortie de secours.

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 2 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Lumination® (LVR - Series) Installation Guide

Prior to installation, disconnect all incoming power to

xture. Remove existing hardware (lens/lens frame,

parabolic louver, reectors/ballast covers, brackets, lamps/

lamp holders). Leave supply and grounding leads.

NOTE: Follow all federal and local regulations when

disposing of lamps and removed components.

Carefully unpack unit from its packaging. Properly inspect

for defects before installing. Wear

work gloves to prevent dirt and oil from being transferred

to the luminaire.

Install LVR Mounting Bracket to each end of the xture by

sliding LVR Mounting Brackets between the xture and

T-grid, ensuring the mounting bracket is centered in the

xture. Secure the LVR Mounting Brackets to the xture

using 4 of the provided #8x1/2” self-drilling screws.

3 4

Install the LVR Fixture T-hinges into the LVR Mounting

Bracket cutouts.

Installation

Components Supplied

The components have been properly packed to avoid damage during transit. Inspect the components to conrm there is no physical

damage. Do not install damaged components.

• LVR Fixture (1)

• LVR Mounting Bracket (2)

• #8x1/2” Self-Drilling Screw (5)

• Green Ground Screw - Optional (1)

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 3 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Lumination® (LVR - Series) Installation Guide

Secure LVR xture to existing uorescent xture using

provided safety tether. Ensure safety tether loop is secured

around T-shaped tab in LVR Mounting Bracket.

Safety tether

Ground wire

Install grounding wire using provided green ground screw

(if existing hole is available) OR #8x1/2” self-drilling screw.

Connect the LED driver to AC line using the provided

ballast disconnect. See “Electrical Connections” section for

wiring details.

AC line

Secure swing door by locking latches found on the end of

the assembled LVR Door.

Diffuser panel

Screw is engagedScrew is disengaged

Squeeze

The diuser panel is engaged over 4 screws on both ends of the LVR luminaire. It may become loose during shipping or if the luminaire

is signicantly twisted during installation. It is important to ensure the diuser is completely engaged to avoid it falling out after

installation is complete. Grasp diuser and gently squeeze together to re-engage over screws.

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 4 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Lumination® (LVR - Series) Installation Guide

GE DRIVER

VIOLET (1-10V +)

PINK (1-10V –)

BLUE (LED –)

RED (LED +) TO LEDs

BLACK (LINE)

WHITE (NEUTRAL)

LVT POSITIVE LEAD

WHITE (NEUTRAL)

LVR CONTROLS AC LINE LEAD

LVT24 POSITIVE LEAD

RED (LOAD)

BLACK (LINE)

VIOLET (1-10V +)

PINK (1-10V –)

LG CONTROLLER

Electrical Connections

Using the provided quick-connect, connect the black (line) of

the AC line to the black 120-277V or 347V wire and the white

(neutral) wires of the AC line to the white or red wires.

Optional: If using a 0-10V dimming controller, connect

matching-colored wires together.

Emergency Bypass Option: Using the provided quick-connect,

connect the black and red wires from the xture to the normal,

non-emergency AC wires to detect whether or not the xture

is in emergency mode.

NOTES:

• Other wires not shown for clarity.

• Self-Test Input must be from same branch circuit as normal

neutral and normal hot.

• Remote test input is performed when input is CLOSED.

LVR2XXXXXXXXXXTQRMWHTE Wiring Diagram

120-277V

WHITE COMMON NEUTRAL

BLACK UNSWITCHED LINE

GROUND

PINK DIMMING 0-10V

VIOLET DIMMING (+)

LVR Fixture

347V

LVR Fixture

RED COMMON NEUTRAL 347V

BLACK UNSWITCHED LINE 347V

GROUND

PINK DIMMING 0-10V

VIOLET DIMMING (+)

EMERGENCY BYPASS OPTION

RED NORMAL NEUTRAL

NORMAL HOT

SELF-TEST INPUT (optional)

REMOTE-TEST INPUT (optional)

BLACK

WHITE/BLACK

WHITE/BLUE

WHITE/RED

Exterior Wires

LVR Fixture

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 5 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Lumination® (LVR - Series) Installation Guide

LVR2XXXXXXXXXXTQRMWHTEEL Wiring Diagram

LINE FILTER

BODINE BSL310 EMBB

YELLOW

YELLOW/BLACK

BLUE

RED

VIOLET

BROWN

BLACK

RED/WHITE

WHITE

WHITE/BLACK

TO LEDs

GE DRIVER

BLACK (LINE)

WHITE (NEUTRAL)

VIOLET (1-10 +)

PINK (1-10 –)

BLUE (LED –)

RED (LED +)

LG CONTROLLER

WHITE (NEUTRAL)

RED (LOAD)

BLACK (LINE)

VIOLET (1-10 +)

PINK (1-10 –)

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 6 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Lumination® (LVR- Series) Installation Guide

LVR CONTROLS

DIMMING LEAD

LVR CONTROLS

DIMMING LEAD

TO LEDs

LVR CONTROLS

AC LINE LEAD

LVT POSITIVE LEAD

LVR CONTROLS

RELAY LEAD

AC SENSE POWER

LVR CONTROLS

AC LINE LEAD

LVT24 POSITIVE LEAD

AC NORMAL/

EMERGENCY POWER

ESRB

WHITE (Self-Test Input)

BLUE (Emergency hot switched to load)

YELLOW (Emergency Neutral)

BROWN (Emergency Hot)

RED (Emergency Neutral)

BLACK (Emergency Hot)

LG CONTROLLER

WHITE (NEUTRAL)

VIOLET (1-10 +)

WHITE/BLUE (Remote Test Input)

WHITE/RED (Remote Test Input)

RED (LOAD)

BLACK (LINE)

VIOLET (1-10 +)

GE DRIVER

PINK (1-10 –)

BLACK (LINE)

WHITE (NEUTRAL)

VIOLET (1-10 +)

PINK (1-10 –)

BLUE (LED –)

RED (LED +)

LVR2XXXXXXXXXXTQRMWHTEB2 Wiring Diagram

LED.com

without notice. All values are design or typical values when measured under laboratory conditions.

Page 7 of 7

(Rev 06/28/23)

IND405-Lumination-LVR-Series-LED-Volumetric-Retrofit-Kit-Installation-Guide_R01

Lumination® (LVR - Series) Installation Guide

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005 (A).

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Note: CONTACT FACTORY for details and limitations when seeking to incorporate this product with an emergency system other than Battery Backup.

Daintree Node

Reset Button &

LED Indicator

Daintree label to be used for

Daintree Node Identication Label and Reset (optional)