Dimensions 210.4 x 95 x 29 mm (8.28 x 3.74 x 1.14")
Weight 529 g (1.2 lb)
Enclosure Material Polycarbonate 110U
Networking Interfaces (10) 10/100/1000 Mbps RJ45 Ethernet Ports
(1) 1 Gbps SFP Port
Management Interface Ethernet In-Band
Bluetooth BLE
Processor Dual-Core 880 MHz, MIPS1004Kc
System Memory 512 MB DDR3
On-Board Flash Storage 512 MB NAND
Power Method External AC/DC Adapter
Power Supply 24VDC, 2.5A Power Adapter (Included)
Supported Voltage Range 24 - 28VDC
Max. Power Consumption 10W (Excludes PoE Output)
ESD/EMP Protection Air: ± 15 kV, Contact: ± 8 kV
Operating Temperature -5to 50° C (23 to 122° F)
Operating Humidity 5 to 95% Noncondensing
Certications CE, FCC, IC
PoE Interfaces (10) 24VDC Passive PoE Out Ports (Pins 4, 5+; 7, 8-)
Passive PoE Max Wattage per Port 15W/24VDC
Passive PoE Voltage Range 24VDC
System Status
RJ45 Data Ports PoE; Speed/Link/Activity
SFP Data Port Link/Activity
Mechanical
Hardware
PoE
LEDs
Specications are subject to change. Ubiquiti products are sold with a limited warranty described at: ui.com/support/warranty
©2020 Ubiquiti Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and UISP are trademarks or registered trademarks of Ubiquiti Inc. in the United States
and in other countries. All other trademarks are the property of their respective owners.
UISP Router Lite
U IS P -R -L ite is a fa nle ss G ig a bit r oute r w ith P oE fle x ibility. Te n G ig abit RJ45 por ts offe r 24V
pa ss iv e P oE o u tput, while the SFP por t offe r s f ibe r conne ctiv ity. U se the U I SP Contr oller
So f twa r e for ce ntr alized co ntr ol a nd monitor in g of a ll U I SP de v ice s.
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
"This equipment has been tested and found to comply with the limits for a Class B digital device.
These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help."
SED Canada
CAN ICES-3(B)/NMB-3(B)
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
The device for operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile satellite systems.
CAN ICES-3(B)/NMB-3(B)
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio ex-
empts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques
de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
RF Exposure Warning
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
located or operating in conjunction with any other antenna or transmitter. Les antennes utilisées
pour ce transmetteur doivent être installé en considérant une distance de séparation de toute
personnes d’au moins
20 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre antenne ou transmetteur.
-
1
-
2
-
3
-
4
dans d''autres langues
Documents connexes
-
Ubiquiti UFiber UF-WIFI Manuel utilisateur
-
-
-
Ubiquiti RocketM Series Guide de démarrage rapide
-
-
-
Ubiquiti R2AC-PRISM Guide de démarrage rapide
-
-
-
Ubiquiti UAP-IW-HD Mode d'emploi