Ubiquiti NSM2 Guide de démarrage rapide

Marque: Ubiquiti

Modèle: NSM2

Catégorie: Antennes réseau

Taper: Guide de démarrage rapide

High-Power 2x2 MIMO

airMAX® TDMA Station

Models: NSM2/NSM3/NSM365/

NSM5/locoM2/locoM5

Introduction

Thank you for purchasing the Ubiquiti Networks®

NanoStation®. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

NanoStation Cable Tie

High-Power 2x2 MIMO

airMAX® TDMA Station

Models: NSM2/NSM3/NSM365/

NSM5/locoM2/locoM5/locoM9

PoE Adapter (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start

Guide

Installation Requirements

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™ is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Back View

Port Cover Release Button

Mounting

Brackets

LED Panels

NanoStationlocoM2/M5NanoStationM2/M3/M5

LED Panels

LED Panel

Power The Power LED will light green when

the device is connected to a power source.

LAN1 Main Ethernet The LED will light steady green

when an active Ethernet connection is made

to the Main/LAN port and flash when there is

activity.

LAN2

Secondary Ethernet (NanoStation M2/M3/M5

only)

The LED will light steady green when

an active Ethernet connection is made to the

Secondary port and flash when there is activity.

Signal In airOS®, you can modify the wireless

signal strength threshold values for each

LED on the Advanced tab under Signal LED

Thresholds. The default values are shown below:

LED will light red when the wireless

signal strength is above ‑94 dBm.

LED will light amber when the wireless

signal strength is above ‑80 dBm.

LED will light green when the wireless

signal strength is above ‑73 dBm.

LED will light green when the wireless

signal strength is above ‑65 dBm.

Ports

Main*

Port

Secondary

Port

Reset

Button

Main/LAN 10/100 Ethernet port used to connect the power

and should be connected to the LAN and DHCP server.

Secondary (NanoStationM2/M3/M5 only) 10/100 Ethernet

port used for bridging and supports software‑configurable

PoE passthrough.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoStation

is already poweredon. Alternatively, a remote reset button is

located on the bottom of the PoE Adapter.

RESET

Switching Gigabit Power Supply / PoE

Reset

Button

* Main is labeled LAN on the NanoStationlocoM2/M5.

Hardware Installation

1. Press the Port Cover Release Button located on the back of

the NanoStation and slide the cover off.

2. Connect an Ethernet cable to the Main/LAN port.

*640-00210-02*

640-00210-02

3. Replace the port cover.

4. Position the NanoStation at the desired location on a pole

and insert a Cable Tie into the slot of the Mounting Bracket.

5. Align the front of the NanoStation toward the other end

of the wireless link. Then tighten the Cable Tie around

thepole.

Note: For the NanoStationM2/M3/M5, two Cable Ties

are provided. Fasten the second Cable Tie to the other

mounting bracket for added security.

Connecting Power over Ethernet

1. Connect the Ethernet cable from the NanoStation to the

POE port of the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the LAN port

of the PoE Adapter.

3. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre‑drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Accessing airOS

Connect to the airOS Configuration Interface.

1. Make sure that your host system is connected via Ethernet

to the NanoStation.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type https://192.168.1.20 in

the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

Note: For the Country setting, U.S. product versions are

restricted to a choice of Canada, Puerto Rico, or the U.S.

to ensure compliance with FCC/IC regulations.

The airOS Configuration Interface will appear, allowing you

to customize your settings as needed. For additional details

on the airOS Configuration Interface, refer to the User Guide

available at documentation.ubnt.com/airmax

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer's responsibility to make sure the device is

operated within local country regulatory requirements.

The Antenna Gain and Output Power fields are provided to

the professional installer to assist in meeting regulatory

requirements.

Specifications

NanoStationM2/M3/M365/M5

Dimensions 294 x 30 x 80 mm

(11.57 x 1.18 x 3.15")

Weight

NSM2/NSM5

NSM3/NSM365

0.4 kg (14.11 oz)

0.5 kg (17.64 oz)

Gain

NSM2

NSM3/NSM365

NSM5

11 dBi

13.7 dBi

16 dBi

Max. Power Consumption 8W

Power Supply 24V, 0.5A PoE Adapter (Included)

Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)

Mounting Pole‑Mounting Kit Included

Networking Interface (2) 10/100 Ethernet Ports

Operating Temperature ‑30 to 75° C (‑22 to 167° F)

Operating Humidity 5 to 95% Noncondensing

NSM2/NSM3/NSM365 Operating Frequency (MHz)

NSM2 2412 ‑ 2462

NSM3 3400 ‑ 3700

NSM365 3650 ‑ 3675

NSM5 Operating Frequency (MHz)

Worldwide 5150 ‑ 5875

USA U‑NII‑1 U‑NII‑2A U‑NII‑2C U‑NII‑3

5150 ‑ 5250 5250 ‑ 5350 5470 ‑ 5725 5725 ‑ 5850

IC 5470 ‑ 5600, 5650 ‑ 5725, 5725 ‑ 5850

NanoStationlocoM2/M5

Dimensions 163 x 31 x 80 mm (6.42 x 1.22 x 3.15")

Weight 0.18 kg (6.35 oz)

Operating Frequency

locoM2

locoM5

2412 ‑ 2462 MHz

Worldwide: 5170 ‑ 5875 MHz

USA: 5725 ‑ 5850 MHz

Gain

locoM2

locoM5

8 dBi

13 dBi

Max. Power Consumption 5.5W

Power Supply 24V, 0.5A PoE Adapter (Included)

Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)

Mounting Pole‑Mounting Kit Included

Networking Interface (1) 10/100 Ethernet Port

Operating Temperature ‑30 to 75° C (‑22 to 167° F)

Operating Humidity 5 to 95% Noncondensing

locoM2 Operating Frequency (MHz)

locoM2 2412 ‑ 2462

locoM5 Operating Frequency (MHz)

Worldwide 5150 ‑ 5875

USA U‑NII‑1 U‑NII‑2A U‑NII‑2C U‑NII‑3

5150 ‑ 5250 5250 ‑ 5350 5470 ‑ 5725 5725 ‑ 5850

IC 5470 ‑ 5600, 5650 ‑ 5725, 5725 ‑ 5850

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2‑wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short‑circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error‑free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

This radio transmitter FCC ID: SWX‑M5N (NSM5) or SWX‑M5LB (locoM5)

has been approved by FCC to operate with the antenna types listed below

with the maximum permissible gain and required antenna impedance for

each antenna type indicated. Antenna types not included in this list, having

a gain greater than the maximum gain indicated for that type, are strictly

prohibited for use with this device.

Antenna Information: Integrated antenna, Gain: 16 dBi (NSM5) or 13 dBi

(locoM5)

Industry Canada

CAN ICES‑3(A)/NMB‑3(A)

This Class A digital apparatus complies with Canadian CAN ICES‑3(A).

To reduce potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that permitted for successful

communication.

This device complies with Industry Canada licence‑exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

This device has been designed to operate with the antennas listed below,

and having a maximum gain of 25 dBi*. Antennas not included in this list

or having a gain greater than 25 dBi are strictly prohibited for use with this

device. The required antenna impedance is 50 ohms.

* Model: NanoStation antenna gain is 25 dBi.

The maximum antenna gain permitted for devices in the bands

5250‑5350 MHz and 5470‑5725 MHz shall comply with the e.i.r.p. limit;

and the maximum antenna gain permitted for devices in the band

5725‑5825MHz shall comply with the e.i.r.p. limits specified for point‑to‑

point and non point‑to‑point operation as appropriate.

This radio transmitter [IC: 6545A‑M5N (NSM5) or 6545A‑M5LB (locoM5)]

has been approved by Industry Canada to operate with the antenna types

listed below with the maximum permissible gain and required antenna

impedance for each antenna type indicated. Antenna types not included

in this list, having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Antenna Information: Integrated antenna, Gain: 16 dBi (NSM5) or 13 dBi

(locoM5)

CAN ICES‑3(A)/NMB‑3(A)

Cet appareil numérique de la classe A est conforme à la norme NMB‑3(A)

Canada.

Pour réduire le risque d’interférence aux autres utilisateurs, le type

d’antenne et son gain doivent être choisies de façon que la puissance

isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire

pour une communication réussie.

Cet appareil est conforme à la norme RSS Industrie Canada exempts de

licence norme(s). Son fonctionnement est soumis aux deux conditions

suivantes:

1. Cet appareil ne peut pas provoquer d’interférences et

2. Cet appareil doit accepter toute interférence, y compris les

interférences qui peuvent causer un mauvais fonctionnement du

dispositif.

Cet appareil a été conçu pour fonctionner avec les antennes énumérés

ci‑dessous, et ayant un gain maximal de 25 dBi*. Antennes pas inclus dans

cette liste ou ayant un gain supérieur à 25 dBi sont strictement interdite

pour une utilisation avec cet appareil. L’impédance d’antenne requise est

50 ohms.

* Modèle: NanoStation gain d’antenne 25 dBi est.

Le gain maximal d’antenne permis pour les dispositifs utilisant les bandes

5250‑5350 MHz et 5470‑5725 MHz doit se conformer à la limite de p.i.r.e.;

le gain maximal d’antenne permis (pour les dispositifs utilisant la bande

5 725‑5 825 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour

l’exploitation point à point et non point à point, selon le cas.

Cet émetteur radio [IC: 6545A‑M5N (NSM5) or 6545A‑M5LB (locoM5)] a

été approuvée par Industrie Canada pour l’exploitation avec l’antenne

types énumérés ci‑dessous avec le gain maximal admissible et requis

l’impédance de l’antenne pour chaque type d’antenne indiqué. Types

d’antenne non inclus dans cette liste, ayant un gain supérieur au gain

maximal indiqué pour ce type, sont strictement interdits pour une

utilisation avec cet appareil.

Informations d’antenne: Antenne intégré, Gain: 16 dBi (NSM5) or 13dBi

(locoM5)

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a

separation distance of at least 55.53 cm from all persons and must not be

located or operating in conjunction with any other antenna or transmitter.

Les antennes utilisées pour ce transmetteur doivent être installé en

considérant une distance de séparation de toute personnes d’au moins

55.53 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre

antenne ou transmetteur.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the product

and it must follow the CE marking.

RoHS/WEEE Compliance Statement

English

European Directive 2012/19/EU requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2012/19/EU verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

La page charge ...

Ubiquiti NSM2 Guide de démarrage rapide

Marque: Ubiquiti

Modèle: NSM2

Catégorie: Antennes réseau

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

italiano: Ubiquiti NSM2 Guida Rapida
English: Ubiquiti NSM2 Quick start guide
română: Ubiquiti NSM2 Ghid de inițiere rapidă

Ubiquiti NSM2 Guide de démarrage rapide

Ubiquiti NSM2 Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents