KitchenAid KFGG504KPS Freestanding Gas Range Le manuel du propriétaire

Marque: KitchenAid

Modèle: KFGG504KPS Freestanding Gas Range

Catégorie: Cuisinières

Taper: Le manuel du propriétaire

W11636129A

FREESTANDING GAS RANGE OWNER’S MANUAL

GUIDE D’UTILISATION DE LA CUISINIÈRE À GAZ

AUTOPORTANTE

MANUAL DEL PROPIETARIO DE LA ESTUFA

AUTÓNOMA A GAS

Table of Contents/Table des matières/Índice

RANGE SAFETY ..............................2

Range Safety.................................2

RANGE MAINTENANCE AND CARE....6

Clean Cycle...................................6

General Cleaning............................7

INSTALLATION INSTRUCTIONS .........8

REQUIREMENTS..............................8

Tools and Parts ..............................8

Location Requirements ....................8

Electrical Requirements ...................9

Gas Supply Requirements .............. 10

INSTALLATION .............................. 11

Unpack Range ............................. 11

Install Anti-Tip Bracket ................... 11

Make Gas Connection ................... 12

Verify Anti-Tip Bracket Is Installed

and Engaged ............................... 13

Level Range ................................ 14

Electronic Ignition System............... 15

Warming Drawer or Premium

Storage Drawer (on some models) ... 16

Storage Drawer (on some models) ... 17

Oven Door .................................. 17

Complete Installation ..................... 18

GAS CONVERSIONS ...................... 18

Propane Gas Conversion ............... 19

Natural Gas Conversion ................. 21

Moving the Range......................... 24

SÉCURITÉ DE LA CUISINIÈRE ......... 25

Sécurité de la cuisinière ................. 25

ENTRETIEN ET RÉPARATION DE LA

CUISINIÈRE................................... 29

Programme de nettoyage ............... 29

Nettoyage général ........................ 30

INSTRUCTIONS D’INSTALLATION .... 31

SPÉCIFICATIONS ........................... 31

Outils et pièces............................. 31

Exigences d’emplacement .............. 32

Spécifications électriques ............... 33

Spécifications de l’alimentation en

gaz............................................ 33

INSTALLATION .............................. 34

Déballage de la cuisinière............... 34

Installation de la bride

antibasculement ........................... 35

Raccordement au gaz.................... 36

Vérifier que la bride antibasculement

est bien installée et engagée ........... 38

Réglage de l’aplomb de la

cuisinière .................................... 38

Système d’allumage électronique..... 39

Tiroir-réchaud ou tiroir de remisage

de qualité supérieure (sur certains

modèles)..................................... 41

Tiroir de rangement (sur certains

modèles)..................................... 41

Porte du four................................ 42

Achever l’installation...................... 42

CONVERSIONS POUR

CHANGEMENT DE GAZ .................. 43

Conversion pour l’alimentation au

propane...................................... 43

Conversion pour l’alimentation au

gaz naturel .................................. 46

Déplacement de la cuisinière........... 50

SEGURIDAD DE LA ESTUFA............ 51

Seguridad de la estufa ................... 51

MANTENIMIENTO Y CUIDADO DE

LA ESTUFA ................................... 55

Ciclo Clean (Limpieza)................... 55

Limpieza general .......................... 56

INSTRUCCIONES DE

INSTALACIÓN................................ 57

REQUISITOS ................................. 57

Herramientas y piezas ................... 57

Requisitos de ubicación ................. 58

Requisitos eléctricos ..................... 59

Requisitos del suministro de gas ...... 59

INSTALACIÓN................................ 60

Desembalaje de la estufa ............... 60

Instalación del soporte antivuelco..... 61

Conexión del suministro de gas ....... 62

Verifique que el soporte antivuelco

esté instalado y enganchado ........... 64

Nivelación de la estufa ................... 64

Sistema de encendido electrónico .... 65

Cajón de calentamiento o cajón de

almacenamiento Premium (en

algunos modelos) ......................... 67

Cajón de almacenamiento (en

algunos modelos) ......................... 67

Puerta del horno........................... 68

Finalización de la instalación ........... 68

CONVERSIONES DE GAS................ 69

Conversión a gas propano .............. 69

Conversión a gas natural................ 72

Cómo mover la estufa.................... 75

IMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

IMPORTANT :

Installateur : Remettre les instructions d’installation au propriétaire.

Propriétaire : Conserver les instructions d’installation pour référence ultérieure.

IMPORTANTE:

Instalador: Deje las Instrucciones de instalación con el propietario.

Propietario de la casa: Conserve las Instrucciones de instalación para referencia futura.

RANGE SAFETY

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or death.

−Do not store gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

−WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch.

•Do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas suppliers

instructions.

•If you cannot reach your gas supplier, call the fire department.

−Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the “What to do if you smell gas” instructions.

WARNING:

Never Operate the Top Surface Cooking Section of this Appliance Unattended

•Failure to follow this warning statement could result in fire, explosion, or burn hazard that

could cause property damage, personal injury, or death.

•If a fire should occur, keep away from the appliance and immediately call your fire

department.

DO NOT ATTEMPT TO EXTINGUISH AN OIL/GREASE FIRE WITH WATER.

The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the

anti-tip bracket fastened down properly.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

To verify the anti-tip bracket is properly installed and engaged:

•Slide range forward.

•Look for the anti-tip bracket securely attached to floor or wall.

•Slide range back so rear range foot is under the anti-tip bracket.

•See Installation Instructions for details.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

DANGER You can be killed or seriously injured if you don't

immediately follow instructions.

WARNING You can be killed or seriously injured if you don’t follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of ventilation

system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or unintended

operation.

In the State of Massachusetts, the following installation instructions apply:

�Installation and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by the

State of Massachusetts.

�Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

�A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the appliance, follow basic precautions,

including the following:

�WARNING: TO REDUCE THE RISK OF TIPPING OF

THE RANGE, THE RANGE MUST BE SECURED BY

PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK

IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE

RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET

SECURELY ATTACHED TO FLOOR OR WALL, AND

SLIDE RANGE BACK SO REAR RANGE FOOT IS

UNDER ANTI-TIP BRACKET.

WARNING

NEVER use this appliance as a space heater to heat or warm

the room. Doing so may result in carbon monoxide poisoning

and overheating of the oven.

WARNING

NEVER cover any slots, holes or passages in the oven

bottom or cover an entire rack with materials such as

aluminum foil. Doing so blocks air flow through the oven and

may cause carbon monoxide poisoning. Aluminum foil linings

may also trap heat, causing a fire hazard.

�CAUTION: Do not store items of interest to children in

cabinets above an appliance or on the backguard of an

appliance - children climbing on the appliance to reach

items could be seriously injured.

�Do Not Leave Children Alone - Children should not be left

alone or unattended in area where appliance is in use.

They should never be allowed to sit or stand on any part of

the appliance.

�Wear Proper Apparel – Loose-fitting or hanging garments

should never be worn while using the appliance.

�User Servicing – Do not repair or replace any part of the

appliance unless specifically recommended in the manual.

All other servicing should be referred to a qualified

technician.

�Storage in or on Appliance – Flammable materials should

not be stored in an oven or near surface units.

�This appliance is not intended for storage.

�Do Not Use Water on Grease Fires – Smother fire or flame

or use dry chemical or foam-type extinguisher.

�Use Only Dry Potholders – Moist or damp potholders on hot

surfaces may result in burns from steam. Do not let

potholder touch hot surface units. Do not use a towel or

other bulky cloth.

�Never Leave Surface Units Unattended at High Heat

Settings – Boilover causes smoking and greasy spillovers

that may ignite.

�Glazed Cooking Utensils – Only certain types of glass,

glass/ceramic, ceramic, earthenware, or other glazed

utensils are suitable for range-top service without breaking

due to the sudden change in temperature.

�Utensil Handles Should Be Turned Inward and Not Extend

Over Adjacent Surface Units – To reduce the risk of burns,

ignition of flammable materials, and spillage due to

unintentional contact with the utensil, the handle of a utensil

should be positioned so that it is turned inward, and does

not extend over adjacent surface units.

�Disconnect power before servicing.

�This appliance is equipped with a three-prong grounding

plug for your protection against shock hazard and should

be plugged directly into a properly grounded receptacle. Do

not cut or remove the grounding prong from this plug.

�Proper Installation - The appliance, when installed, must be

electrically grounded in accordance with local codes, or in

the absence of local codes, with the National Electrical

Code, ANSI/NFPA 70 or the Canadian Electrical Code,

CSA C22.1-02. In Canada, the appliance must be

electrically grounded in accordance with Canadian

Electrical Code. Be sure your appliance is properly installed

and grounded by a qualified technician.

�Injuries may result from the misuse of appliance doors or

drawers such as stepping, leaning, or sitting on the doors or

drawers.

�Maintenance – Keep range area clear and free from

combustible materials, gasoline, and other flammable

vapors and liquids.

�Top burner flame size should be adjusted so it does not

extend beyond the edge of the cooking utensil. This

instruction is based on safety considerations.

�Do not use replacement parts that have not been

recommended by the manufacturer (e.g. parts made at

home using a 3D printer).

�Clean Cooktop With Caution – If a wet sponge or cloth is

used to wipe spills on a hot cooking area, be careful to

avoid steam burn. Some cleaners can produce noxious

fumes if applied to a hot surface.

�Use Care When Opening Door – Let hot air or steam

escape before removing or replacing food.

�Do Not Heat Unopened Food Containers – Build-up of

pressure may cause container to burst and result in injury.

�Keep Oven Vent Ducts Unobstructed.

�DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN – Heating elements may be hot

even though they are dark in color. Interior surfaces of an

oven become hot enough to cause burns. During and after

use, do not touch, or let clothing or other flammable

materials contact heating elements or interior surfaces of

oven until they have had sufficient time to cool. Other

surfaces of the appliance may become hot enough to cause

burns – among these surfaces are oven vent openings and

surfaces near these openings, oven doors, and windows of

oven doors.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the appliance, follow basic precautions,

including the following:

�Care must be taken to prevent aluminum foil and meat

probes from contacting heating elements.

For self-cleaning ranges –

�CAUTION: DO NOT LEAVE FOOD OR COOKING

UTENSILS, ETC., IN OVEN DURING THE PYROLYTIC

SELF-CLEANING MODE OF OPERATION.

�Do Not Clean Door Gasket – The door gasket is essential

for a good seal. Care should be taken not to rub, damage,

or move the gasket.

�Do Not Use Oven Cleaners – No commercial oven cleaner

or oven liner protective coating of any kind should be used

in or around any part of the oven.

�Clean Only Parts Listed in Manual.

�Before Self-Cleaning the Oven – Remove broiler pan and

other utensils. Wipe off all excessive spillage before

initiating the cleaning cycle.

For units with ventilating hood –

�Clean Ventilating Hoods Frequently – Grease should not be

allowed to accumulate on hood or filter.

�When flaming foods under the hood, turn the fan on.

For smart enabled ranges and ovens

�Remote operation – This appliance is configurable to allow

remote operation at any time. Do not store any flammable

materials or temperature sensitive items inside, on top or

near surface units of the appliance.

SAVE THESE INSTRUCTIONS

RANGE MAINTENANCE AND

CARE

Clean Cycle

AquaLift®Technology is an innovative cleaning solution that

utilizes heat and water to release baked-on spills from the oven in

less than 1 hour. This new cleaning technology is a low-heat,

odor-free alternative to traditional self-cleaning options.

Allow the oven to cool to room temperature before using the Clean

cycle. If your oven cavity is above 200°F (93°C), it will appear in

the display, and the Clean cycle will not be activated until the oven

cavity cools down.

To Clean:

1. Remove all racks and accessories from the oven cavity, and

wipe excess soil. Use a plastic scraper to remove easily

removed soils.

2. Pour 13/4cups (14 oz [414 mL]) of distilled or filtered water

onto the bottom of the empty oven, and close the oven door.

IMPORTANT: Do not use chemicals or other additives with the

water. Do not open the oven door during the Clean cycle. The

water on the oven bottom is hot.

3. Press CLEAN/AQUALIFT SELF CLEAN and then START on

the oven control panel.

4. Allow 40 minutes for cleaning and cooldown. A beep will

sound when the Clean cycle is complete.

5. Press OFF/CANCEL/CANCEL UPPER at the end of the cycle.

OFF/CANCEL/CANCEL UPPER may be pressed at any time

to stop the Clean cycle.

6. Remove the residual water and loosened soils with a sponge

or cloth immediately after the Clean cycle is complete. Much

of the initial 13/4cups (14 oz [414 mL]) of water will remain in

the oven after the cycle is completed. If additional soils

remain, leave a small amount of water in the oven bottom to

assist with the cleaning.

7. If any soils remain, remove them with a nonscratch scrubbing

sponge or plastic scraper. Additional Clean cycles may be run

to help remove the stubborn soils.

IMPORTANT: Do not use oven cleaners. The use of

chemicals, including commercial oven cleaners or metal

scouring pads, may cause permanent damage to the

porcelain surface of the oven interior.

NOTE:

�The range should be level to ensure that the entire surface

of the bottom of the oven cavity is covered by water at the

beginning of the Clean cycle.

�For best results, use distilled or filtered water. Tap water

may leave mineral deposits on the oven bottom.

�Before removing the residual water and loosened soils at

the end of the Clean cycle, insert a cloth or paper towel

between the lower edge of the oven door and the front

frame to keep water from spilling onto the front of the

range and the floor.

�Soil baked on through several cooking cycles will be more

difficult to remove with the Clean cycle.

�Nonabrasive scrub sponges or eraser-style cleaning pads

(without cleaners) can be effective for cleaning the oven

cavity walls, oven door, and oven bottom for difficult soils.

For best results, moisten the pads and sponges before

use.

�Run an additional Clean cycle for stubborn soils.

�Affresh®✝Kitchen Appliance Cleaner and affresh®Cooktop

Cleaner may be used to clean the oven bottom, walls, and

door when the oven has finished the cycle and returned to

room temperature. If affresh®Cooktop Cleaner is used, it

is recommended to wipe out the cavity with distilled water

as well. Refer to the Quick Start Guide for ordering

information.

�Additional AquaLift®Technology Cleaning Kits may be

obtained by ordering Part Number W10423113RP. Refer to

the Quick Start Guide for ordering information.

✝Affresh®is a registered trademark of Whirlpool, U.S.A.

General Cleaning

IMPORTANT: Before cleaning, make sure all controls are OFF

and the oven and cooktop are cool. Always follow label

instructions on cleaning products.

Soap, water, and a soft cloth or sponge are suggested first, unless

otherwise noted.

EXTERIOR PORCELAIN ENAMEL SURFACES (on some

models)

Food spills containing acids, such as vinegar and tomato, should

be cleaned as soon as the entire range is cool. These spills may

affect the finish.

Cleaning Method:

�Glass cleaner, mild liquid cleaner, or nonabrasive scrubbing

pad: Gently clean around the model/serial/rating plate because

scrubbing may remove numbers.

�Affresh®Kitchen and Appliance Cleaner Part Number

W10355010 (not included):

See the Quick Start Guide for ordering information.

STAINLESS STEEL (on some models)

NOTE: To avoid damage to stainless steel surfaces, do not use

soap-filled scouring pads, abrasive cleaners, Cooktop Cleaner,

steel-wool pads, gritty washcloths, or abrasive paper towels.

Damage may occur to stainless steel surfaces, even with one-time

or limited use.

Cleaning Method:

�Rub in direction of grain to avoid damaging.

�Affresh®Stainless Steel Cleaner Part Number W10355016

(not included):

See the Quick Start Guide for ordering information.

METALLIC PAINT (on some models)

Do not use abrasive cleaners, cleaners with bleach, rust

removers, ammonia, or sodium hydroxide (lye) because paint

surface may stain.

PORCELAIN-COATED GRATES AND CAPS

Food spills containing acids, such as vinegar and tomato, should

be cleaned as soon as the cooktop, grates and caps are cool.

These spills may affect the finish.

To avoid chipping, do not bang grates, and caps against each

other or hard surfaces such as cast iron cookware.

Do not reassemble caps on burners while wet. Do not clean in the

Self-Cleaning cycle.

Cleaning Method:

�Nonabrasive plastic scrubbing pad and mildly abrasive

cleanser: Clean as soon as cooktop, grates, and caps are

cool.

�Dishwasher (grates only, not caps):

Use the most-aggressive cycle. Cooked-on soils should be

soaked or scrubbed before going into a dishwasher.

Although the burner grates are durable, they may lose their

shine and/or discolor when washed in a dishwasher.

�Gas Grate and Drip Pan Cleaner Part Number 31617 (not

included):

See the Quick Start Guide for ordering information.

SURFACE BURNERS

Food spills containing acids, such as vinegar and tomato, should

be cleaned as soon as the cooktop, grates, and caps are cool.

These spills may affect the finish.

To avoid chipping, do not bang grates and caps against each

other or hard surfaces such as cast iron cookware.

Do not reassemble caps on burners while wet.

Do not clean in the Self-Cleaning cycle.

Do not clean in dishwasher.

Cleaning Method:

�Nonabrasive plastic scrubbing pad and mildly abrasive

cleanser:

Clean as soon as cooktop, grates, burners, and caps are cool.

�Gas Grate and Drip Pan Cleaner (not included).

COOKTOP CONTROLS

To avoid damage to the cooktop controls, do not use steel wool,

abrasive cleansers, or oven cleaner.

To avoid damage, do not soak knobs. When replacing knobs,

make sure knobs are in the Off position.

On some models, do not remove seals under knobs.

Cleaning Method:

�Soap and water: Pull knobs straight away from control panel to

remove

GRIDDLE (on some models)

To avoid damaging the nonstick surface, do not use steel wool or

abrasive cleaners.

Cleaning Method:

�Mild detergent.

�Dishwasher: Although the griddle is durable, it may lose its

shine and/or is color when washed in a dishwasher.

CONTROL PANEL AND OVEN DOOR EXTERIOR

To avoid damage to the control panel, do not use abrasive

cleaners, steel-wool pads, gritty washcloths, or abrasive paper

towels.

Cleaning Method:

�Glass cleaner and soft cloth or sponge: Apply glass cleaner to

soft cloth or sponge, not directly on panel.

�Affresh®Kitchen and Appliance Cleaner Part Number

W10355010 (not included):

See the Quick Start Guide for ordering information.

OVEN RACKS

Cleaning Method:

�Steel-wool pad.

�For racks that have discolored and are harder to slide, a light

coating of vegetable oil applied to the rack guides will help

them slide.

�Dishwasher (steam rack water reservoir only, not racks):

Although the water reservoir is durable, it may lose its shine

and/or discolor when washed in a dishwasher.

STORAGE/WARMING DRAWER (on some models)

Check that storage/warming drawer is cool and empty before

cleaning.

Cleaning Method:

�Mild detergent

OVEN CAVITY

Use AquaLift®Technology regularly to clean oven spills.

Do not use oven cleaners.

Food spills should be cleaned when oven cools. At high

temperatures, foods react with porcelain. Staining, etching, pitting,

or faint white spots can result.

Cleaning Method:

�Self-Cleaning cycle: See the “Self-Cleaning Cycle” or “Clean

Cycle” section first.

INSTALLATION INSTRUCTIONS

REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

�Tape measure

�Flat-blade screwdriver

�Phillips screwdriver

�1/8" flat-blade screwdriver

�Level

�Hand or electric drill

�Hammer

�Wrench or pliers

�Pipe wrench

�15/16" combination wrench

�1/4" drive ratchet

�3/8" nut driver

�1/8" drill bit (for wood floors)

�Marker or pencil

�Pipe-joint compound

resistant to Propane gas

�Noncorrosive leak-detection

solution

�3/16" carbide-tipped

masonry drill bit

(for concrete/ceramic floors)

(For Slide-in/Front Control

Ranges)

For Propane/Natural Gas

Conversions

�3/8" combination wrench

�1/2" combination wrench

�5/8" combination wrench

�9/32" nut driver

�Quadrex®†or Phillips

screwdriver

�Masking tape

�3/8" nut driver

(For Slide-in/Front Control

Ranges)

Parts Supplied

Check that all parts are included.

A. Anti-tip bracket

B. #12 x 15/8" (4.1 cm) screws (2)

Anti-tip bracket must be securely mounted to floor or wall.

Thickness of flooring may require longer screws to anchor bracket

to floor.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See “Electrical Requirements” and

“Gas Supply Requirements” sections.

NOTE: Be sure to purchase only whirlpool factory-certified parts

and accessories for your appliance. Your installation may require

additional parts. To order, refer to the contact information

referenced in your Quick Start Guide.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

�It is the installer’s responsibility to comply with installation

clearances specified on the model/serial/rating plate. The

model/serial/rating plate is located behind the oven door on the

top right/left-hand side of the oven frame.

�The range should be located for convenient use in the kitchen.

�Recessed installations must provide complete enclosure of the

sides and rear of the range.

�All openings in the wall or floor where range is to be installed

must be sealed.

�Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

�The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see “Install Anti-Tip Bracket”

section.

�Grounded electrical supply is required. See “Electrical

Requirements” section.

�Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

�Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

�Use an insulated pad or 1/4" (6.4 mm) plywood under range if

installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This oven

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation

Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home Installations,

ANSI A225.1/NFPA 501A or with local codes. In Canada, the

installation of this range must conform with the current standards

CAN/CSA-Z240.1 - latest edition, or with local codes.

Mobile Home Installations Require:

�When this range is installed in a mobile home, it must be

secured according to the instructions in this document.

†Quadrex®is a registered trademark of NLW Holdings, Inc.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and 36"

(91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood

combination above the range, follow the range hood or microwave

hood combination installation instructions for dimensional

clearances above the cooktop surface.

A. For minimum clearance to top of cooktop, see NOTE*.

B. 13" (33 cm) max. upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. 18" (45.7 cm) upper side cabinet to countertop

E. In U.S.A.: 30" (76.2 cm) min. opening width

F. The shaded areas are recommended for installation of rigid gas pipe.

G. 11" (27.9 cm)

H. 17" (43.2 cm)

I. 2" (5.1 cm)

J. 41⁄2" (11.4 cm)

K. 3" (7.6 cm) min. clearance from both sides of range to side wall or

other combustible material.

L. Grounded outlet

M. Cabinet door or hinges should not extend into the cutout.

*NOTE: 24" (61.0 cm) minimum when bottom of wood or metal

cabinet is covered by not less than 1/4" (6.4 mm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance

between the top of the cooking platform and the bottom of an

uncovered wood or metal cabinet.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

IMPORTANT: The range must be electrically grounded in

accordance with local codes and ordinances, or in the absence of

local codes, with the National Electrical Code, ANSI/NFPA 70 or

Canadian Electrical Code, CSA C22.1.

This range is equipped with an electronic ignition system that will

not operate if plugged into an outlet that is not properly polarized.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

�A 120 V, 60 Hz, AC only, 15 A fused, ground and polarized

electrical circuit is required. A time-delay fuse or circuit breaker

is also recommended. It is recommended that a separate

circuit serving only this range be provided.

�Electronic ignition systems operate within wide voltage limits,

but proper grounding and polarity are necessary. Check that

the outlet provides 120 V power and is correctly grounded.

�This gas range is not required to be plugged into a GFCI

(Ground-Fault Circuit Interrupter) outlet. It is recommended

that you do not plug an electric spark ignition gas range or any

other major appliance into a GFCI wall outlet as it may cause

the GFCI to trip during normal cycling.

�Performance of this range will not be affected if operated on a

GFCI-protected circuit. However, occasional nuisance tripping

of the GFCI breaker is possible due to the normal operating

nature of electronic gas ranges.

NOTE: The metal chassis of the range must be grounded in order

for the control panel to work. If the metal chassis of the range is

not grounded, no keypads will operate. Check with a qualified

electrician if you are in doubt as to whether the metal chassis of

the range is grounded.

Gas Supply Requirements

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 14"(36 cm) water

column.

Examples of a qualified person include: licensed heating

personnel, authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with the National Fuel Gas Code ANSI Z223.1/NFPA 54

or, in Canada, the Natural Gas and Propane Installation Code,

CSA B149.1 - latest edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturer’s instructions. Refer to the

“Complete Connection” in the “Make gas connection” section for

the leak testing instructions.

Type of Gas

Natural Gas:

�This range is factory set for use with Natural gas. See “Gas

Conversions” section. The model/serial rating plate located on

the oven frame behind of the oven door has information on the

types of gas that can be used. If the types of gas listed do not

include the type of gas available, check with the local gas

supplier.

Propane Gas Conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See “Gas

Conversions” section.

Gas Supply Line

�Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result in

insufficient gas supply. With Propane gas, piping or tubing size

can be 1/2" (1.3 cm) minimum. Usually, Propane gas suppliers

determine the size and materials used in the system.

�NOTE: Pipe-joint compounds that resist the action of Propane

gas must be used. Do not use TEFLON®✝tape.

Flexible Metal Appliance Connector:

�If local codes permit, a new CSA design-certified, 4 to 5 ft (122

to 152.4 cm) long, 1/2" (13 mm) or 3/4" (19 mm) I.D., flexible

metal appliance connector may be used for connecting range

to the gas supply line.

�A 1/2" (13 mm) male pipe thread is needed for connection to

the female pipe threads of the inlet to the appliance pressure

regulator.

�Do not kink or damage the flexible metal tubing when moving

the range.

�Must include a shut-off valve:

Install a manual gas line shut-off valve in an easily accessible

location. Do not block access to shut-off valve. The valve is for

turning on or shutting off gas to the cooktop.

A. Gas supply line

B. Shut-off valve “open” position

C. To range

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be used.

The inlet pressure to the regulator should be as follows for proper

operation:

Natural Gas:

Minimum pressure: 5" (12.7 cm) WCP

Maximum pressure: 14" (35.5 cm) WCP

Propane Gas:

Minimum pressure: 11" (27.9 cm) WCP

Maximum pressure: 14" (35.5 cm) WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial/rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" (2.5 cm) water column pressure above the manifold pressure

shown on the model/serial rating plate.

Line pressure testing above 1/2 psi (3.5 kPa) gauge

[14" (35.5 cm) WCP]

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of 1/2 psi (3.5 kPa).

✝TEFLON®is a registered trademark of Chemours.

Line pressure testing at 1/2 psi (3.5 kPa) gauge [14" (35.5 cm)

WCP] or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2 psi (3.5 kPa).

INSTALLATION

Unpack Range

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall

appliance.

Failure to do so can result in back or other injury.

1. Remove shipping materials, tape and film from range.

2. Remove oven racks and parts package from inside oven.

3. Do not remove the shipping base at this time.

A. Shipping base

4. On Ranges Equipped with a Storage Drawer:

Remove the storage drawer. See the “Storage Drawer”

section. Use a 1/4" (6.4 mm) drive ratchet to lower the rear

leveling legs one-half turn. Use a wrench or pliers to lower

front leveling legs one-half turn.

A. 1/4" (6.4 mm)

drive ratchet

B. Rear leveling leg

C. Wrench or pliers

D. Front leveling leg

On Ranges Equipped with a Warming Drawer or Premium

Storage Drawer:

On ranges equipped with a warming drawer or premium

storage drawer, the rear legs cannot be accessed by removing

the warming drawer or premium storage drawer. It will be

necessary to adjust the rear legs from outside the range. Use

wrench or pliers to lower the front and rear leveling legs one-

half turn.

A. Rear leveling leg

B. Wrench or pliers

C. Front leveling leg

Install Anti-Tip Bracket

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death or

serious burns to children and adults.

1. Remove the anti-tip bracket from where it is taped inside the

storage drawer, warming drawer, or premium storage drawer

2. Determine which mounting method to use: floor or wall. If you

have a stone or masonry floor, you can use the wall mounting

method. If you are installing the range in a mobile home, you

must secure the range to the floor.

3. Determine and mark centerline of the cutout space. The

mounting can be installed on either the left side or right side of

the cutout. Position mounting bracket against the wall in the

cutout so that the V-notch of the bracket is 129⁄16" (31.9 cm)

from centerline as shown.

A. 129⁄16" (31.9 cm)

B. Bracket V-notch

4. Drill two 1/8" (3 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following

illustrations.

Floor Mounting

Rear position Front position Diagonal

(2 options)

Wall Mounting

5. Using the Phillips screwdriver, mount anti-tip bracket to the

wall or floor with the two #12 x 15/8" (4.1 cm) screws provided,

mount anti-tip bracket to the wall or floor.

6. Move range close enough to opening to allow for final gas and

electrical connections. Remove shipping base, cardboard or

hardboard from under range.

7. Move range into its final location, making sure rear leveling leg

slides into anti-tip bracket.

8. Move range forward onto shipping base, cardboard or

hardboard to continue installing the range using the following

installation instructions.

Make Gas Connection

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 14"(36 cm) water

column.

Examples of a qualified person include: licensed heating

personnel, authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical flexible connection

1. Apply pipe-joint compound made for use with propane gas to

the smaller thread ends of the flexible connector adapters

(see B and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and the other

adapter to the gas shut-off valve. Tighten both adapters, being

certain not to move or turn the gas pressure regulator.

3. Use a 15/16" (2.4 cm) combination wrench and an adjustable

wrench to attach the flexible connector to the adapters.

IMPORTANT: All connections must be wrench-tightened. Do

not make connections to the gas regulator too tight. Making

the connections too tight may crack the regulator and cause a

gas leak. Do not allow the regulator to turn when tightening

fittings.

A. Gas pressure regulator

B. Use pipe-joint compound.

C. Adapter (must have 1/2"

(1.3 cm) male pipe thread

D. Flexible connector

E. Manual gas shutoff valve

F. 1/2" (1.3 cm) or 3/4" (1.9 cm)

gas pipe

G. Use pipe-joint compound.

H. Adapter

Complete Connection

1. Check that the gas pressure regulator shut-off valve is in the

“on” position.

A. Gas pressure regulator shut-off valve shown in the

“on” position

2. Open the manual shut-off valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

3. Test all connections by brushing on an approved noncorrosive

leak-detection solution. If bubbles appear, a leak is indicated.

Correct any leak found.

4. Remove cooktop burner caps and grates from parts package.

Place the burner bases as indicated by the following

illustration for your model:

For Model KFGG504KPS

A. Medium (Semi

Rapid)

B. Large (Ultra

Rapid)

C. Oval (OV)

D. Small (Auxiliary)

E. Large (Ultra Rapid)

5. Burner caps should be level when properly positioned. If

burner caps are not properly positioned, surface burners will

not light. Place burner grates over burners and caps

A. Burner base

B. Burner cap

C. Burner grate

Alignment: Be sure to align the gas tube opening in the

burner base with the orifice holder on the cooktop and the

igniter electrode with the notch in the burner base.

6. Place the burner caps on the appropriate burner bases.

IMPORTANT: The bottom of the small and medium caps are

different. Do not put the wrong size burner cap on the burner

base.

Small (Auxiliary) Medium (Semi Rapid) Large (Ultra Rapid)

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

7. Plug into a grounded 3-prong outlet.

8. Slide range into final location, making sure the rear leveling

leg slides into the slot of the anti-tip bracket.

Verify Anti-Tip Bracket Is Installed

and Engaged

On Ranges Equipped with a Storage Drawer:

1. Remove the storage drawer. See the “Storage Drawer”

section.

2. Use a flashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges Equipped with a Warming Drawer or

Premium Storage Drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer or premium storage drawer, and grasp the

lower right or left side of the control panel as shown.

NOTE: If your countertop is mounted with a backsplash, it

may be necessary to grasp the range higher than is shown in

the illustration.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than 1/2" (1.3 cm) off the floor

without resistance, stop tilting the range and lower it gently

back to the floor. The range foot is not engaged in the anti-tip

bracket.

IMPORTANT: If there is a snapping or popping sound when

lifting the range, the range may not be fully engaged in the

bracket. Check to see if there are obstructions keeping the

range from sliding to the wall or keeping the range foot from

sliding into the bracket. Verify that the bracket is held securely

in place by the mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the slot

of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. Changes to

the gas supply must be performed by a qualified service

technician. If you need assistance or service, refer to the Quick

Start Guide for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is engaged

in the anti-tip bracket.

If the rear of the range lifts more than 1/2" (1.3 cm) off the floor

without resistance, the anti-tip bracket may not be installed

correctly. Do not operate the range without anti-tip bracket

installed and engaged. If you need assistance or service, refer

to the Quick Start Guide for contact information.

Level Range

Determine if you have AquaLift®Technology or Steam Clean by

referring to the “Range Maintenance and Care” section.

For Ranges with AquaLift®Technology or Steam Clean:

1. Place level on the oven bottom as indicated in one of the two

figures below depending on the size of the level. Check with

the level side to side and front to back.

2. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

For Ranges without AquaLift®Technology or Steam Clean:

1. Place a standard flat rack in oven.

2. Place level on the rack and check levelness of the range, first

side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

4. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

Style 1: Ranges Equipped with a Storage Drawer:

Use a 1/4" (6.4 mm) drive ratchet, wrench or pliers to adjust

leveling legs up or down until the range is level. Push range back

into position. Check that rear leveling leg is engaged in the anti-tip

bracket.

Style 2: Ranges Equipped with a Warming Drawer or

Premium Storage Drawer:

Use a wrench or pliers to adjust leveling legs up or down until the

range is level. Push range back into position. Check that rear

leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance

and best cleaning results using AquaLift®Technology and Steam

Clean functions.

Electronic Ignition System

Initial Lighting and Gas Flame Adjustments

Cooktop and oven burners use electronic igniters in place of

standing pilots. When the cooktop control knob is turned to the

“LITE” position, the system creates a spark to light the burner.

This sparking continues, as long as the control knob is turned to

“LITE.”

When the oven control is turned to the desired setting, sparking

occurs and ignites the gas.

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the “LITE” position.

The flame should light within 4 seconds. The first time a burner is

lit, it may take longer than 4 seconds to light because of air in the

gas line.

If Burners Do Not Light Properly:

�Turn cooktop control knob to the “OFF” position.

�Check that the range is plugged in. Check that the circuit

breaker has not tripped or the household fuse has not blown.

�Check that the gas shutoff valves are set to the “open”

position.

�Check that burner caps are properly positioned on burner

bases.

A. Incorrect

B. Correct

Repeat start-up. If a burner does not light at this point, turn the

control knobs to the “OFF” position and contact your dealer or

authorized service company for assistance.

Power Failure

In case of prolonged power failure, the surface burners can be lit

manually. Hold a lit match near a burner, and turn knob

counterclockwise to LITE. After the burner lights, turn knob to

desired setting.

Check Operation of Oven Bake Burner

1. Remove the oven rack.

2. To remove the oven bottom: Remove 2 screws at the rear of

the oven bottom. Lift the rear of the oven bottom up and back

until the front of the panel is away from the front frame.

Remove it from oven and place on a covered surface.

A. Screws

B. Oven bottom

3. You can check the burner flame by using a mirror. Insert a

mirror to one side of the burner. Look into the mirror to check

flame.

4. Push the BAKE pad.

5. Press the START pad.

The oven bake burner should light within 8 seconds. Under certain

conditions, it may take the burner up to 50 to 60 seconds to light.

Electronic igniters are used to light the bake and broil burners.

Refer to the Quick Start Guide and online Control Guide for proper

operation of the oven controls.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop “low” burner

flame should be a steady blue flame approximately 3/8" (9.5 mm)

high.

A. Low flame

B. High flame

To adjust standard burner:

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

If the “low” flame needs to be adjusted:

A. Control knob stem

B. Screwdriver

C. Pliers

1. Light 1 burner and turn to lowest setting.

2. Remove the control knob.

Hold the knob stem with a pair of pliers. Use a small flat blade

screwdriver to turn the screw located in the center of the

control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from “LO” to “HI,”

checking the flame at each setting and ensuring there is a

steady flame.

5. Repeat the previous steps for each burner.

Adjust Oven Bake Burner Flame (if needed)

1. On models with a warming drawer, remove access cover plate

(1 screw) located at the back of the warming drawer

compartment.

2. Check the oven bake burner for proper flame.

This flame should have a 1/2" (1.3 cm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should be

clean and soft in character. No yellow tips, blowing or lifting of

flame should occur.

3. If the oven bake flame needs to be adjusted, locate the air

shutter near the center rear of the range. Loosen the locking

screw and rotate the air shutter until the proper flame appears.

Tighten locking screw.

A. Locking screw

B. Air shutter

4. Push CANCEL/OFF when finished.

5. Reinstall flame spreader and oven bake burner cover.

Check Operation of Oven Broil Burner

1. Close the oven door.

2. Press the BROIL pad.

3. Press the START pad.

The oven burner should light within 8 seconds. Under certain

conditions, it may take the burner up to 50 to 60 seconds to light.

Refer to the Quick Start Guide and online Control Guide for proper

operation of the oven controls.

Adjust Oven Broil Burner Flame (if needed)

Look through oven window to check broil burner for proper flame.

This flame should have a 1/2" (1.3 cm) long inner cone of bluish-

green, with an outer mantle of dark blue, and should be clean and

soft in character. No yellow tips, blowing or lifting of flame should

be present.

If flame needs to be adjusted:

1. Loosen the lock screw on the air shutter located at the rear of

the broil burner.

2. Adjust the air shutter as needed.

3. Tighten lock screw.

A. Lock screw

B. Air shutter

4. Press CANCEL/OFF when finished.

Warming Drawer or Premium

Storage Drawer (on some models)

Remove all items from inside the baking drawer, warming drawer

or premium storage drawer, and then allow the range to cool

completely before attempting to remove the drawer.

To Remove:

1. Open the drawer to its fully open position.

2. Using a flat-blade screwdriver, gently loosen the drawer from

the glide alignment notch, and then lift up the drawer

alignment tab from the glide.

A. Flat-blade screwdriver

B. Drawer alignment tab

C. Drawer glide notch

3. Repeat Step 2 on the other side. The drawer is no longer

attached to the drawer glides. Using both hands, pick up the

drawer to complete the removal.

To Replace:

1. Align the forward drawer notches with the notches in the

drawer glides on both sides. Place the rear alignment tabs into

the drawer glides on both sides.

A. Drawer alignment tab

B. Drawer glide notch

2. Push the warming drawer or premium storage drawer in all the

way.

3. Gently open and close the warming drawer or premium

storage drawer to ensure it is seated properly on the glides on

both sides.

Storage Drawer (on some models)

The storage drawer can be removed. Before removing, make sure

drawer is cool and empty.

To Remove:

1. Pull the storage drawer straight back to the drawer stop.

A. Drawer stop notch

2. Lift up the front of the drawer and pull the drawer out.

To Replace:

1. Lift up the front of the drawer and place the rear of the drawer

inside the range so that the drawer stop notch is behind the

drawer glide.

2. Lower the drawer so that the edge of the slide rail drops into

the slot in the drawer glide.

3. Slowly push the drawer into the range.

A. Engage drawer glide

NOTE: When properly installed, the rear slides on the bottom of

the drawer will engage the base rails and the drawer will not tip

when items are placed in the drawer.

Oven Door

For normal range use, it is not suggested to remove the oven

door. However, if removal is necessary, make sure the oven is

OFF and cool. Then, follow these instructions. The oven door is

heavy.

To Remove:

1. Open oven door all the way.

2. Pinch the hinge latch between two fingers and pull forward.

Repeat on other side of oven door.

A. Hinge Latch

3. Close the oven door as far as it will shut.

4. Lift the oven door while holding both sides.

Continue to push the oven door closed and pull it away from

the oven door frame.

To Replace:

1. Insert both hanger arms into the door.

2. Open the oven door.

You should hear a click as the door is set into place.

3. Move the hinge levers back to the locked position. Check that

the door is free to open and close. If it is not, repeat the

removal and installation procedures.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See the “Level Range” section.

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, read

the “Range Maintenance and Care” section.

6. Read the Quick Start Guide and online Control Guide.

7. Turn on surface burners and oven. See the Quick Start Guide

and online Control Guide for specific instruction on range

operation.

If Range Does Not Operate, Check the Following:

�Household fuse is intact and tight; or circuit breaker has not

tripped.

�Range is plugged into a grounded 3-prong outlet.

�Gas pressure regulator shutoff valve is in the “on” position.

�Electrical supply is connected.

�See the online “Troubleshooting” section.

8. When the range has been on for 5 minutes, check for heat. If

the range is cold, turn off the range and check that the gas

supply line shut-off valve is open.

�If the gas supply line shut-off valve is closed, open it, and

then repeat the 5 minute test as outlined above.

�If the gas supply line shutoff valve is open, press the

CANCEL button on the oven control panel and contact a

qualified technician.

If You Need Assistance or Service:

Please reference the Quick Start Guide for contact information.

GAS CONVERSIONS

Gas conversions from Natural gas to propane gas or from

propane gas to Natural gas must be done by a qualified installer.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 14"(36 cm) water

column.

Examples of a qualified person include: licensed heating

personnel, authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

WARNING:

This conversion kit shall be installed by a qualified

service agency in accordance with the manufacturer’s

instructions and all applicable codes and requirements of

the authority having jurisdiction. If the information in

these instructions is not followed exactly, a fire, an

explosion or production of carbon monoxide may result

causing property damage, personal injury or loss of life.

The qualified service agency is responsible for the proper

installation of this kit. The installation is not proper and

complete until the operation of the converted appliance is

checked as specified in the manufacturer’s instructions

supplied with the kit.

Propane Gas Conversion

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death or

serious burns to children and adults.

1. Turn manual shutoff valve to the closed position.

A. To range

B. Manual shut-off valve closed position

C. Gas supply line

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator (Natural gas

to Propane)

1. Remove the premium storage drawer, warming drawer or

baking drawer. See the “Remove/Replace Drawer”, “Storage

Drawer” or “Warming Drawer or Premium Storage Drawer”

section.

2. Locate gas pressure regulator at rear of the drawer

compartment.

NOTE: On models with a warming drawer or baking drawer,

an access cover must be removed to access the gas pressure

regulator.

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

3. Remove plastic cover from gas pressure regulator cap.

4. Turn gas pressure regulator cap counterclockwise with a 5/8"

(1.6 cm) combination wrench to remove.

NOTE: Do not remove the spring beneath the cap.

A. Plastic cover

B. Gas pressure regulator cap with solid end facing out

C. Gas pressure regulator cap with hollow end facing

out

D. Washer

E. Gas pressure regulator cap

5. Turn over the gas pressure regulator cap and reinstall on

regulator so that the hollow end faces out and the marking

“↓LP” is facing the direction shown in the above drawing.

6. Replace plastic cover over gas pressure regulator cap.

To Convert Surface Burners (Natural Gas to

Propane Gas)

1. Remove burner cap.

2. Remove the burner base.

A. Burner cap

B. Burner base

C. Alignment pins

D. Igniter electrode

E. Gas tube opening

3. Apply masking tape to the end of a 9/32" (7 mm) nut driver to

help hold the gas orifice spud in the nut driver while changing

it. Press nut driver down onto the gas orifice spud and remove

by turning it counterclockwise and lifting out. Set gas orifice

spud aside.

A. Orifice spud

B. Orifice spud holder

C. Screw

D. Spark electrode

4. Gas orifice spuds are stamped with a number on the side or

top. Replace the Natural gas orifice spud with the correct

Propane gas orifice spud.

A. Stamped Number

Refer to the following chart for correct Propane gas orifice spud

placement.

Propane Gas Orifice Spud Chart for Surface Burner

Placement Burner

Rating/ Type Size ID Number

LF 14,200 BTU 1.08AM 108AM

LR 8,000 BTU 0.84AM 084AM

RF 14,200 BTU 1.08AM 108AM

RR 5,000 BTU 0.64AM 064AM

CTR 8,000 BTU 0.84AM 084AM

NOTE: Refer to the Tech Sheet located on the rear cover for the

applicable individual burner BTU rating per fuel type.

5. Place Natural gas orifice spuds in the cardboard orifice spud

holder.

6. Replace the burner base.

7. Replace burner cap.

8. Repeat steps 1-7 for the remaining burners.

To Convert Oven Bake Burner (Natural Gas to

Propane Gas)

1. Remove the oven racks and the oven door. See the “Oven

Door” section.

2. Remove two screws and washers at the rear of the oven

bottom.

3. Lift the rear of the oven bottom up and back until the front of

the panel is away from the front frame. Remove from oven

and set it aside on a covered surface.

A. Screws

B. Oven bottom

4. Remove 1 screw from the bake burner.

5. Slide the front of the bake burner to the side to remove tab

from front of oven. Lift the back of the bake burner off the oven

orifice, and set the bake burner aside.

A. Screws

B. Oven bottom

6. Using a 3/8" (9.5 mm) nut driver or combination wrench, turn

the Natural gas bake burner orifice spud counterclockwise to

remove. The spud will be stamped with a “47.”

7. Replace the “47” spud with a “56” spud. Install the Propane

gas bake burner orifice spud, turning it clockwise until snug.

IMPORTANT: Do not overtighten.

A. Orifice spud

8. Position the back of the bake burner over the oven orifice, and

slide the tab on front of the bake burner into the front of the

oven.

9. Reattach the bake burner with 1 screw.

10. Position the front of the oven bottom panel toward the front

frame and lower the rear of the oven bottom panel into the

oven.

11. Reattach the oven bottom panel with screws.

La page est en cours de chargement...

KitchenAid KFGG504KPS Freestanding Gas Range Le manuel du propriétaire

Marque: KitchenAid

Modèle: KFGG504KPS Freestanding Gas Range

Catégorie: Cuisinières

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

Documents connexes

KitchenAid W10750372A Manuel utilisateur

KitchenAid KFGG504KPS Freestanding Gas Range Le manuel du propriétaire

KitchenAid KFGG504KPS Freestanding Gas Range Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents