Thermador PRG364WLG Guide d'installation

THERMADOR.COM

Installation

INSTRUCTIONS

Professional Series Pro Grand

®

Ranges

THERMADOR.COM

Installation

INSTRUCTIONS

Models |

Modèles |

Modelos:

PRD364WDGU/C

PRD364WIGU/C

PRD364WLGU/C

PRD366WGU/C

PRD484WCGU/C

PRD486WDGU/C

PRD486WIGU/C

PRD486WLGU/C

PRD48WCSGU/C

PRD48WDSGU/C

PRD48WISGU/C

PRD48WLSGU/C

PRD606WCG

PRD606WCSG

PRD606WEG

PRD606WESG

PRG364WDG

PRG364WLG

PRG366WG

PRG486WDG

PRG486WLG

Professional Series Pro Grand

®

Ranges

Table of Contents (English) ............................................................... 2

Table de Matières (Français) ........................................................... 28

Índice de Materias (Español) ........................................................... 55

Page. 2

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Table of

CONTENTS

Safety ...................................................................................... 3

Important safety instructions........................................... 3

Installation instructions .......................................................... 6

Planning information ....................................................... 6

Ventilation requirements ................................................ 6

Installation clearances...................................................... 7

Gas and electric locations ............................................... 12

Unpacking and moving the range .................................. 13

Door removal and adjustment ........................................ 14

Installing the anti-tip bracket (required) ......................... 16

Gas requirements and connection ................................. 17

Electrical requirements and connection for

GAS models..................................................................... 18

Electrical requirements and connection for

DUAL FUEL models ......................................................... 19

Low backguard installation (optional) ............................. 22

Placing and leveling the range........................................ 23

Data rating label.............................................................. 24

Burner test ...................................................................... 25

Installer checklist .................................................................... 27

Final check ....................................................................... 27

Support, accessories, and parts.................................back page

Safety

DEFINITIONS

9 WARNING

This indicates that death or serious injuries may occur as a

result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may occur as a

result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

Page. 3

Safety

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Installer: Save these instructions for the local gas

inspector’s use. Please leave these Installation Instructions

with this unit for the owner.

Owner: Please retain these instructions for future

reference. Before using your appliance, be sure to read

this manual.

WARNING

ELECTRICAL SHOCK HAZARD

• Disconnect power before installing or

servicing. Before turning power ON, be sure

that all controls are in the OFF position.

• DO NOT remove connections.

• DO NOT use an extension cord.

• Improper grounding can result in a risk of

electric shock.

• Failure to follow these instructions can result

in death, fire, or electrical shock.

WARNING

RANGE TIPPING HAZARD:

• All ranges can tip and injury can result. To

prevent accidental tipping of the range,

attach it to the floor by installing the anti-tip

bracket supplied.

• A risk of tip-over may exist if the appliance

is not installed in accordance with these

instructions. For all ranges an anti-tip device

MUST be installed.

• A child or adult can tip the range and be killed.

• DO NOT operate the range without the anti-tip

device in place and engaged. Failure to do so can

result in death or serious burns to children or

adults.

• If the range is pulled away

from the wall for cleaning,

service or for any other

reason, ensure that the anti-

tip device is properly re-

engaged when the range is

pushed back against the wall.

In the event of abnormal

usage (such as a person

standing, sitting, or leaning

on an open door), failure to

take this precaution can result in tipping of the

range. Personal injury might result from spilled hot

liquids or from the range itself.

Local codes vary. Installer is responsible for ensuring that

the installation, gas connections, and grounding comply

with all applicable codes. Failure to follow appropriate

local codes and regulations may void the warranty.

The installation of appliances designed for manufactured

(mobile) home installation must conform with the

Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280 [formerly the Federal Standard for

Mobile Home Construction and Safety, Title 24, HUD {Part

280}] or with local codes where applicable.

The installation of appliances designed for Recreational

Park Trailers must conform with state or other codes or, in

the absence of such codes, with the Standard for

Recreational Park Trailers, ANSI A119.5.

Examine the appliance after unpacking it. In the event of

transport damage, do not plug it in.

WARNING

If the information in this manual is

not followed exactly, a fire or

explosion may result causing

property damage, personal injury

or death.

-- DO NOT store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your

building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

-- Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

Page. 4

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Remove all tape and packaging before using the

appliance. Dispose of packaging in an environmentally-

responsible manner. Never allow children to play with

packaging material.

This appliance must be grounded. Grounding reduces the

risk of electric shock by providing a safe pathway for

electric current in the event of a short circuit.

Show the owner the location of the circuit breaker or fuse.

Mark it for easy reference.

The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical Code,

NFPA 70 latest edition, or the Canadian Electric Code,

CSA C22.1-02.

DO NOT install this appliance outdoors.

For Massachusetts installations:

• Installation must be performed by a qualified or

licensed contractor, plumber or gas fitter qualified or

licensed by the state, province or region where this

appliance is being installed.

• Shut-off valve must be a “T” handle gas cock.

• Flexible gas connector must not be longer than 36''

(914 mm).

Verify the type of gas supplied to the location. Ensure that

the appliance is connected to the type of gas for which it

is certified.

This appliance is capable of being safely placed in

operation in the event of a power failure. Only the

standard top burners can be manually lit.

Always keep appliance area clear from combustible

materials, gasoline and other flammable vapors and

liquids.

Natural gas — 7 inch water column. (17.4 mb) min., 14

inch (34.9 mb) maximum

Propane gas — 11 inch water column. (27.4 mb) min., 14

inch (34.9 mb) maximum

This appliance is shipped from the manufacturer for use

with natural gas. For use with propane (LP) gas, a

conversion kit must be purchased separately. An

authorized servicer must do the LP conversion. See the

back cover for information about service, parts, and

accessories.

CAUTION

When connecting the unit to propane gas, make

certain the propane gas tank is equipped with its own

high-pressure regulator in addition to the pressure

regulator supplied with the appliance. The maximum

gas pressure to this appliance must not exceed 14.0''

water column (34.9 mb) from the propane gas tank to

the pressure regulator.

This appliance complies with one or more of the

following Standards:

• UL 858, The Standard for the Safety of Household

Electric Ranges

• ANSI Z21.1, The American National Standard for

Household Cooking Gas Appliances

• CAN1-1.1-M81, Domestic Gas Ranges

• CSA C22.2 No. 61, Household Cooking Ranges

Check local building codes for the proper method of

appliance installation. Local codes vary; it is the

responsibility of the installer to ensure installation is in

accordance with these codes. Installation, electrical

connections, and grounding must comply with all

applicable codes.

In the absence of local codes the appliance should be

installed in accordance with the National Electric Code

NFPA 70 current issue and National Gas Code NFPA 54/

ANSI Z223.1 – current issue. In Canada, installation must

be in accordance with the Canadian Electric Code, CSA

C22.1-02 and the CAN 1-B149.1 and .2 – Installation

Codes for Gas Burning Appliances and/or local codes.

State of California Proposition 65 Warning:

: WARNING

This product can expose you to chemicals including

vinyl chloride, which is known to the State of California

to cause cancer and birth defects or other

reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Page. 5

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Rear clearance requirements

• To avoid staining on the back wall, high temperature,

non-porous construction materials suitable for use in a

cooking environment are recommended.

• Models PCG305xx, PRG305xx, PRG304xx, PRD305xx,

PRD304, and PRD606xx are suitable for 0'' rear

clearance to combustible surfaces.

• All other models:

• When using the included island trim a minimum 6"

(152 mm)* rear clearance is required to a

combustible surface*.

• When installing against a combustible surface, a

Thermador

®

low backguard is required for a 0''

rear clearance to the combustible surface. A

Thermador low backguard must be purchased

separately.

• A rear clearance to a surface covered in a non-

combustible material (metal, ceramic tile, brick,

marble, or stone)

*

is 0" when using the included

island trim.

*Clearances of less than 6'' (152 mm) should be approved by the

local codes and/or by the local authority having jurisdiction.

 Clearances from non-combustible materials are not part of the

ANSI Z21.1 scope and are not certified by CSA.

WARNING

To avoid possible burn or fire hazard, a backguard

designed specifically for this appliance should be

installed whenever the appliance is used.

WARNING

To eliminate risk of burns or fire caused by reaching

over heated surface units, cabinet storage located

above the surface units should be avoided.

CAUTION

This unit is designed as a cooking appliance. Based on

safety considerations, never use it for warming or

heating a room. Doing so may result in carbon

monoxide poisoning and overheating the appliance.

Page. 6

Installation instructions

Planning information

9 CAUTION

To prevent possible damage to cabinets and cabinet

finishes, use only materials and finishes that will not

discolor or divide into layers. Materials should be able

to withstand temperatures up to 194 °F (90 °C). Heat

and moisture resistant adhesive must be used if the

product is to be installed in laminated cabinetry.

Check with the manufacturer to ensure materials meet

these requirements.

Before using your appliance, be sure to read this manual.

Pay special attention to the “Important safety

instructions” located at the beginning of the manual.

Tools needed

• 7/16'' box end wrench or ratchet

• 3/16'' (4.76 mm) drill bit

• Hand or electric drill

• 1/8'' (3.17 mm) drill bit

• 12'' Adjustable wrench

• T-20 screwdriver

• T-30 screwdriver

• Tape measure

• Furniture dolly or air sled

• Phillips screwdriver

• Level

• Marking instrument

• Protective gloves

• Safety glasses

Items not included

• Drywall / Concrete Anchors

•Rope/Twine

• 2 – NPT Flare Adapters

• Pipe Compound / Tape

• ¾'' (19 mm) Flex Line

IMPORTANT: There is a possibility to discolor the back

wall under certain cooking conditions.

Ventilation requirements

9 WARNING

This appliance should not be installed with a

ventilation system that directs air in a downward

direction toward the range. This type of ventilation

system may cause ignition and combustion problems

with the appliance resulting in personal injury,

property damage, or unintended operation.

Ventilating systems that direct the air upwards do not

have any restriction.

Refer to the “Ventilation planning guide” for approved

ventilation combinations.

It is strongly recommended that this appliance be installed

in conjunction with a Thermador

®

vent hood. Due to the

high heat capability of this unit, particular attention should

be paid to the hood and duct work installation to assure it

meets local building codes.

Downdraft ventilation should not be used. The

“Ventilation planning guide” indicates the ventilation

hood options and blower capacity guidelines that are

recommended for use.

Due to the high heat of the rangetop burners, installing a

microwave oven with a ventilation system over the

rangetop is not recommended.

Ventilation hoods and blowers are designed for use with

single wall ducting. However, some local building codes or

inspectors may require double wall ducting. Consult local

building codes and/or local agencies before starting to

assure that hood and duct installation will meet local

requirements.

NOTICE: Most range hoods contain combustible

components which must be considered when planning the

installation.

Page. 7

Ventilation preparation

To prepare for the ventilation

1. Select hood and blower models:

• For wall installations, the hood width must, at a

minimum, equal the width of the range/rangetop.

Where space permits, a hood larger in width than

the range/rangetop may be desirable for

improved ventilation performance.

• For island installations, the hood width should

overhang the width of the range/rangetop by a

minimum of 3'' (76 mm) on each side.

2. Hood placement:

• For best smoke elimination, the lower edge of the

hood should be installed 30'' (762 mm) above the

range cooking surface.

• If the hood contains any combustible materials

(i.e. a wood covering), it must be installed a

minimum of 36'' (914 mm) above the cooking

surface.

3. Consider make-up air:

• Due to the high volume of ventilation air, a source

of outside replacement air is recommended. This

is particularly important for tightly sealed and

insulated homes.

• A qualified heating and ventilating contractor

should be consulted.

Installation clearances

Cabinet requirements

The appliance is a free standing unit. If the unit is to be

placed adjacent to cabinets, the clearances shown in this

section are required. The same clearances apply to island

installations, except for the overhead cabinets, which must

have a space wide enough to accept the island hood.

• See the “Ventilation planning guide” for

recommended hood options. Due to the high heat of

the burners, installing a microwave oven with a

ventilation system over the appliance is not

recommended on any model other than the 30'' 5–

burner. Refer to OTR manufacturer’s installation

manual for clearances.

• The gas and electrical supply should be within the

zones shown in the “Gas and electric locations”

section.

• The shaded area behind the appliance indicates an

opportunity to discolor the back wall under certain

cooking conditions.

• There must be a minimum of 5'' (127 mm) side

clearance from the appliance to combustible vertical

surfaces above the 36'' (914 mm) counter height.

• Within the 5'' (127 mm) side clearance to combustible

vertical surfaces above 36'' (91.4 cm), the maximum

wall cabinet depth must be 13” (330 mm).

• Wall cabinets within this 5'' (127 mm) side clearance

must be 18'' (457 mm) above the 36'' (914 mm) high

countertop.

• The maximum depth of the cabinets hanging on either

side of the hood is 13'' (330 mm).

• There is a 36'' (914 mm) minimum clearance required

between the top of the cooking surface and the

bottom of an unprotected cabinet. A 30'' (762 mm)

clearance can be used when the bottom of the wood

or metal cabinet is protected by not less than 1/4''

(6 mm) of a flame retardant material covered with not

less than No. 28 MSG sheet steel, 0.015'' (0.38 mm)

thick stainless steel, 0.024'' (0.61 mm) aluminum, or

0.02'' (0.51 mm) thick copper.

• DO NOT obstruct the flow of combustion and

ventilation air to the appliance.

• The appliance height is adjustable. The level of the

range top must be at the same level or above the

counter top level.

• To provide proper ventilation of the range DO NOT

remove range feet.

• Any openings in the wall behind the appliance and in

the floor under the appliance must be sealed.

Rear clearance requirements

• To avoid staining on the back wall, high temperature,

non-porous construction materials suitable for use in a

cooking environment are recommended.

• Model PCG305xx, PRG305xx, PRG304xx, PRD305xx,

PRD304, and PRD606xx are suitable for 0'' rear

clearance to combustible surfaces.

• All other models:

• When using the included island trim a minimum 6"

(152 mm)* rear clearance is required to a

combustible surface*.

• When installing against a combustible surface, a

Thermador

®

low backguard is required for a 0''

rear clearance to the combustible surface. A

Thermador low backguard must be purchased

separately.

• A rear clearance to a surface covered in a non-

combustible material (metal, ceramic tile, brick,

marble, or stone)

*

is 0" when using the included

Island Trim.

*Clearances of less than 6'' (152 mm) should be approved by the

local codes and/or by the local authority having jurisdiction.

 Clearances from non-combustible materials are not part of the

ANSI Z21.1 scope and are not certified by CSA.

Page. 8

Cabinet clearance requirements with the

included island trim

 as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI

Z21.1 scope and are not certified by CSA. Clearances of less than 6'' (152 mm) should be approved by the local codes and/or by the local authority

having jurisdiction.

5

" (12

7

)

1

8

"

(457)

1

8

"

(

45

7)

1

8

"

(457)

30

"

(762) –

36" (914)

3

0

"

(

7

6

2

)

–

3

6

"

(

9

1

4

)

30

"

(762) –

36" (914)

36" or 48"

(914 or 1

219 )

3

6

"

o

r

4

8

"

(

9

1

4

o

r

1

2

1

9

)

36" or 48"

(914 or 1

219 )

13"

(330)

1

3

"

(

3

0

)

13"

(330)

6" (152)6"

(

1

5

2

)

6" (152)

35 ⅞" (911) –

36 ¾" (933)

35 ⅞" (911) –

36 ¾" (933)

35 ⅞" (911) –

36 ¾" (933)

inches (mm)

Page. 9

Cabinet clearance requirements with a

low backguard (purchased separately)

 as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI

Z21.1 scope and are not certified by CSA. Clearances of less than 6'' (152 mm) should be approved by the local codes and/or by the local authority

having jurisdiction.

1

8"

(

457)

1

8

"

(

45

7

)

1

8"

(

457)

36" or 48"

(914 or 1219 )

3

6

"

o

r

4

8

"

(

9

1

4

o

r

1

2

1

9

)

36" or 48"

(914 or 1219 )

0"0"

5

" (12

7

)

30" (762) –

36

"

(914)

3

0

"

(

7

6

2

)

–

3

6

"

(

9

1

4

)

30" (762) –

36

"

(914)

13"

(330)

1

3

"

(

3

0

)

13"

(330)

35 ⅞" (911) –

36 ¾" (933)

35 ⅞" (911) –

36 ¾" (933)

35 ⅞" (911) –

36 ¾" (933)

inches (mm)

Page. 10

Cabinet clearance requirements for the

60'' range with the included island trim

 as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 6'' (152 mm) must be approved by the local codes and/or by the local authority having

jurisdiction.

60" (15

24)

6

0

"

(

1

5

2

4

)

60" (15

24)

1

8

"

(457)

1

8

"

(

45

7)

1

8

"

(457)

0"0"

5

" (12

7

)

30

" (762) –

36

" (914)

3

0

"

(

7

6

2

)

–

3

6

"

(

9

1

4

)

30

" (762) –

36

" (914)

13"

(330)

1

3

"

(

3

0

)

13"

(330)

35 ⅞" (911) –

36 ¾" (933)

35 ⅞" (911) –

36 ¾" (933)

35 ⅞" (911) –

36 ¾" (933)

inches (mm)

Page. 11

Side clearances

• The model shown is with the included island trim. A

low backguard option is available (purchased

separately).

• For an island trim install, counter surface should have

a cantilever edge meeting the back section of the

island trim.

• If an inner wall is used under the cantilever counter

top there should be a 1/8'' (3 mm) gap from the rear

of the range.

• There is a 48-3/4'' (1,238 mm) total clearance.

• Shaded area behind range indicates minimum

clearance to combustible surfaces. Combustible

materials cannot be located within this area with the

island trim.

• There is a 25-1/8'' (638 mm) maximum recess depth.

inches (mm)

28" (711)

27¼" (692)

30" (762) –

36" (914)

25⅛" (638)

35⅞" (911) –

36¾" (933)

26⅞" (683)

48¾" (1238)

6" (152) 6" (152) 6" (152)

Page. 12

Gas and electric locations

Gas and electrical requirements

• IMPORTANT: If not already present, install gas shut-

off valve in an easily accessible location. Make sure all

users know where and how to shut off the gas supply

to the range.

• Any opening in the wall behind the appliance and any

opening in the floor under the appliance must be

sealed.

• The range must be connected only to the type of gas

for which it is certified. If the range is to be connected

to propane gas, ensure that the propane gas supply

tank is equipped with its own high pressure regulator

in addition to the pressure regulator supplied with the

range.

• The gas and electrical supplies must be within the

zones as indicated in the image below.

• A manual gas shut-off valve must be installed external

to the appliance, in a location accessible from the

front, for the purpose of shutting off the gas supply.

The supply line must not interfere with the back of the

unit.

• The range is supplied with its own pressure regulator

that has been permanently mounted within the range

body.

• For nearly-flush installation to the back wall, the gas

supply line and electrical cord should not go above

10'' (254 mm) above the floor.

• When the power supply cord or conduit is connected

to the mating receptacle or terminal block cover, the

combined plug/receptacle or terminal block cover/

conduit connector should protrude no more than 2''

(51 mm) from the rear wall.

Model A B

36'' (913 mm) 4 ½'' (123 mm) 4 ½'' (123 mm)

48'' (1,219 mm) 6 – 7/16'' (163 mm) 6 – 7/16'' (163 mm)

60'' (1,524 mm) 4 ½'' (123 mm) 4 ½'' (123 mm)

10"

(254)

10"

(254)

10"

(254)

AA

36", 48", 60"

(914, 1219, 1524)

36", 48", 60"

(914, 1219, 1524)

36", 48", 60"

(914, 1219, 1524)

BB

2"

(51)

2"

(51)

2"

(51)

Electric

Zone

Electric

Zone

Electric

Zone

Gas

Zone

Gas

Zone

Gas

Zone

CC

LL

CC

LL

inches (mm)

Page. 13

Unpacking and moving the

range

9 CAUTION

DO NOT lift the range by the oven door’s

handle, as this may damage the door hinges

and cause the door to fit incorrectly.

DO NOT lift the appliance by the range’s

control panel.

The unit is heavy and should be handled

accordingly. Proper safety equipment such as

gloves and adequate manpower of at least two

people must be used in moving the range to

avoid injury and to avoid damage to the unit or

the floor.

Rings, watches, and any other loose items that

may damage the unit or otherwise might

become entangled with the unit should be

removed.

Hidden surfaces may have sharp edges. Use

caution when reaching behind or under

appliance.

DO NOT use a hand truck or appliance dolly on

the back or front of the unit. Handle from the

side only.

Unpacking the range

NOTES:

• DO NOT remove control panel foam until unit is

completely installed.

• DO NOT lift on the control panel at any point

during the installation.

To unpack the appliance

1. Remove the outer carton and packing materials from

the shipping pallet.

2. Leave the protective film over brushed-metal surfaces,

to protect finish from scratches, until the range is

installed in its final position.

3. Remove the grates, burner caps and oven racks to

facilitate handling.

4. If desired, the oven doors may be removed (see “Door

removal and adjustment”).

Moving the range

Due to the weight, a furniture dolly with soft wheels or an

air lift should be used to move this unit. The weight must

be supported uniformly across the bottom.

To remove the pallet bolts

1. To remove the pallet bolts in the front and in the back,

use a 7/16'' wrench or ratchet and socket to remove

the pallet bolt from the bottom of the pallet.

2. Lift range and remove it from the pallet. Use

additional help as required to remove from pallet.

3. Transport the range by furniture dolly close to its final

location. Unit should not be dollied from the front. DO

NOT slide the range across an unprotected floor.

4. The range can then be tipped back and supported on

the rear legs while the dolly is carefully removed. THE

FLOOR UNDER THE LEGS SHOULD BE PROTECTED

BEFORE PUSHING THE UNIT INTO POSITION.

Page. 14

Door removal and adjustment

9 CAUTION

• USE CAUTION WHEN REMOVING THE DOOR.

THE DOOR IS VERY HEAVY.

• Make sure oven is cool and power to the oven has

been turned off before removing the door. Failure

to do so could result in electrical shock or burns.

• The oven door is heavy and fragile. Use both

hands to remove or replace the door.

• Failure to grasp the oven door firmly and properly

could result in personal injury and product

damage.

• With the door off, never release the levers and try

to close the hinges. Without the weight of the

door, the powerful springs will snap the hinges

closed with great force.

To remove the oven door

1. Be sure to read the above CAUTION before

attempting to remove the door.

2. Open the door fully.

3. Flip the hinge clips for both sides of the door. A

screwdriver may be required to carefully pry the clip.

4. Close the door gently until it stops against the hinge

clips. The open hinge clips will hold the door open at

a slight angle, about 30°, from the closed position.

5. Grasp the door firmly on the ends of the door. Lift the

door up and out. There will be some spring resistance

to overcome.

6. Place the door in a safe and stable location.

To reinstall the oven door

1. Hold the door firmly in both hands.

2. Hold the door at a 30° angle from the closed position.

Insert hinges centered evenly into the hinge slots. The

hinges will securely hook into the slots when properly

installed. DO NOT force, bend or twist the door.

3. Open door fully to expose hinges, levers, and slots.

Page. 15

4. Flip the hinge until seated on the bracket. A

screwdriver may be required to carefully push the clip.

5. Close and open the door slowly to ensure it is

correctly and securely in place.

To remove the warming drawer

1. On the top of the warming drawer door, remove the

three (3) T-20 torx screws.

2. Rotate the warming drawer door out and then pull

down to disengage from the retainer tabs.

To check door fit and adjustment

1. Open and close the door slowly to test the movement

and the fit of the door to the oven cavity. DO NOT

force the door to open or close. If the door is properly

installed, it should move smoothly and rest straight on

the front of the range when closed.

2. The range must be level for proper alignment of the

oven doors, see “Placing and leveling the range”.

3. Verify that the hinges are properly seated into the

hinge slots, and that the hinge clips are fully engaged

into the slots.

If door or handle appears slightly tilted

4. Rotate the large torx head screw located directly

above the hinge receiver with a T-30 torx driver.

Rotate each screw respective to its side and direction

the door needs to be adjusted.

NOTE: The steam oven door is not adjustable.

2

1

Page. 16

Installing the anti-tip bracket

(required)

For all ranges, an anti-tip device must be installed as per

these instructions.

9 WARNING

RANGE TIPPING HAZARD:

• All ranges can tip and injury can result. To

prevent accidental tipping of the range,

attach it to the floor by installing the anti-tip

bracket supplied.

• A risk of tip-over may exist if the appliance

is not installed in accordance with these

instructions. For all ranges an anti-tip device

MUST be installed.

• A child or adult can tip the range and be killed.

• DO NOT operate the range without the anti-tip

device in place and engaged. Failure to do so can

result in death or serious burns to children or

adults.

• If the range is pulled away from the wall for

cleaning, service or for any other reason, ensure

that the anti-tip device is properly re-engaged

when the range is pushed back against the wall. In

the event of abnormal usage (such as a person

standing, sitting, or leaning on an open door),

failure to take this precaution can result in tipping

of the range. Personal injury might result from

spilled hot liquids or from the range itself.

9 WARNING

ELECTRICAL SHOCK HAZARD:

• Use extreme caution when drilling holes into the

wall or floor as there may be concealed electrical

wires.

• Identify the electrical circuits that could be

affected by the installation of the anti-tip bracket,

then turn off power to these circuits.

• Failure to follow these instructions may result in

electrical shock or other personal injury.

IMPORTANT:

• Hardware provided is for mounting through standard

thickness wood studs. Installers are responsible to

provide hardware for other types of mounting

situations.

• Contact a qualified installer or contractor to

determine the proper method for drilling holes

through the wall or floor material (such as ceramic tile,

hardwood, etc.)

• The bracket may be attached to a solid wood surface

having a minimum wall thickness of ¾'' (19 mm).

• The thickness of the wall or floor may require use of

longer screws, available at your local hardware store.

• In all cases, at least two (2) of the bracket mounting

screws must be fastened to solid wood surface.

• Use appropriate anchors when fastening the mounting

bracket to any material other than hard-wood or

metal.

• If the range is moved to a new location, the anti-tip

device must be removed and reinstalled.

Anti-tip bracket installation

Installing the anti-tip bracket for 36'' and 48'' models

1. Locate the anti-tip bracket in the literature packet,

inside the box that was on top of the appliance.

2. Place bracket on the floor in a position shown below.

The bracket may be placed on either the left or the

right side.

3. For walls, wall studs, or floors composed of solid

wood or metal, drill 1/8'' (3 mm) pilot holes.

4. Secure to floor and/or wall stud using the (4) 1 ½''

(38 mm) Phillips head screws provided.

Later, when the unit is installed, the adjustable leg will

slide under the bracket.

Model Value for 'X'

36'' 3-7/8'' (98 mm)

48'' steam models only 1-5/8'' (41 mm)

48'' all other models 1-3/4'' (44 mm)

C

L

C

L

xx

C

L

Page. 17

Installing the anti-tip bracket for 60'' models

1. Locate the anti-tip bracket in the literature packet,

inside the box that was on top of the appliance.

2. Place bracket on the floor in a position shown below.

The bracket may be placed on either the left or the

right side.

3. For walls, wall studs, or floors composed of solid

wood or metal, drill 1/8'' (3 mm) pilot holes.

4. Secure to floor and/or wall stud using the (4) 1 ½''

(38 mm) Phillips head screws provided.

Later, when the unit is installed, the caster will slide under

the bracket. If the range is moved to a new location, the

anti-tip device must be removed and reinstalled.

Gas requirements and

connection

9 CAUTION

The appliance must be isolated from the gas supply

piping system by closing its individual manual shut-off

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than 1/

2 psig (3.5kPa.).

9 WARNING

DO NOT use a flame of any kind to check for gas

leaks.

9 CAUTION

When connecting unit to propane gas, make certain

the propane gas tank is equipped with its own high

pressure regulator in addition to the pressure

regulator supplied with the appliance. The pressure of

the gas supplied to the appliance regulator must not

exceed 14" water column (34.9 mb).

Verify the type of gas being used at the installation site.

Make certain the range matches the type of gas available

at this location.

The gas supply connections shall be made by a competent

technician and in accordance with local codes or

ordinances. In the absence of local codes, the installation

must conform to the National Fuel Gas Code ANSI

Z223.1/NFPA54- current issue.

High altitude

This appliance has been tested for operation up to an

altitude of 10,100 ft (3,078 m) elevation above sea level.

If desired, for altitudes above 2,000 feet (610 m) elevation

above sea level, adjustments can be made with a High

Altitude Kit. If flame performance is satisfactory,

adjustment will not be required. It is required that a

Certified Professional make the high altitude adjustments

during installation.

Gas requirements

Natural gas requirements:

• Inlet Connection: 1/2'' NPT internal (Minimum 3/4''

dia. flex line)

• Supply Pressure: 7'' min. to 14'' max. water column

(17.4 to 34.9 mb)

• Manifold Pressure: 5'' water column (12.5 mb)

Propane gas requirements:

• Inlet Connection: 1/2'' NPT internal (Minimum 3/4''

dia. flex line)

• Supply Pressure: 11'' min. to 14'' max. water column

(27.4 mb to 34.9 mb)

• Manifold Pressure: 10'' water column (24.9 mb)

Model Value for 'X'

60'' 2'' (51 mm)

C

L

C

L

xx

C

L

Page. 18

Gas connection

To connect the gas

1. Make sure the gas supply is turned off at the manual

shut-off valve before connecting the appliance.

2. Use a ¾'' (19 mm) flex line to connect between the

gas supply and the appliance gas inlet. The gas supply

line connection is located at the lower right portion.

The appliance gas inlet connection is ½'' (12.7 mm)

NPT.

• Use caution to avoid crimping the ¾'' (19 mm) flex

line when making bends. Suggested length of flex

line is 48" (1219 mm); however, please check local

codes for your area's requirements before

installation.

3. Use pipe sealing compound or Teflon

®

tape on the

pipe threads. DO NOT apply sealing compound or

tape to flare fittings. Take care not to apply excessive

pressure when tightening the fittings.

4. Leak testing of the appliance shall be in accordance

with the following instructions:

• Turn on gas and check supply line connections for

leaks using a soap and water solution.

5. Bubbles forming indicate a gas leak. Repair all leaks

immediately.

Electrical requirements and

connection for GAS models

9 WARNING

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being

turned ON accidentally. Always disconnect appliance

from the electric supply either by disconnecting

power cord or shutting off the breaker at the service

panel before servicing the appliance.

9 WARNING

This product must be properly grounded.

9 WARNING

Electrical grounding instructions

This appliance is equipped with a three-prong

grounding plug for your protection against shock

hazard and should be plugged directly into a properly

grounded receptacle. DO NOT cut or remove the

grounding prong from this plug.

9 CAUTION

Improper grounding or reverse polarization will cause

malfunction (such as continuous sparking of the

burner igniters). This can damage the appliance and

can create a condition of shock hazard. If the

dedicated circuit is not correctly grounded and

polarized, it is the responsibility and obligation of the

installer and user to have the existing receptacle

changed to a properly dedicated grounded and

polarized receptacle. This must be accomplished in

accordance with all applicable local codes and

ordinances by a qualified electrician. In the absence of

local codes and ordinances, the receptacle

replacement shall be in accordance with the National

Electric Code.

INSTALLER — show the owner the location of the circuit

breaker. Mark it for easy reference.

¾" (19) external threads¾" (19) external threads¾" (19) external threads

½" (12.7) internal threads½" (12.7) internal threads½" (12.7) internal threads

{

¾" (19)

Flex line

¾" (19)

Flex line

¾" (19)

Flex line

inches (mm)

Page. 19

Gas unit electrical connection

Electrical supply circuit requirements

The cord supplied with the

gas ranges having an electric

griddle or grill requires a

NEMA 5-20 receptacle. All

other gas units require a

NEMA 5-15 receptacle.

• Before you plug in an electrical cord, be sure all

controls are in the OFF position.

• A neutral supply wire must be provided from the

power source (breaker) because critical range

components, including the surface burner spark

reignition modules, require it to operate safely and

properly.

• All 120 volt models must be plugged into a mating 3-

prong, grounding-type receptacle. The receptacle

must be connected to a properly dedicated grounded

and polarized electrical power supply rated at

120VAC, Single Phase, 60Hz.

• Observe all governing codes and ordinances when

grounding. In the absence of these codes or

ordinances observe National Electrical Code ANSI/

NFPA No. 70 current issue, or the relevant Canadian

Electric Code, CSA C22.1-02.

Electrical requirements and

connection for DUAL FUEL

models

9 WARNING

An improper 240/208 VAC power supply will cause

malfunction, damage to this appliance, and possibly

create a condition of shock hazard.

9 WARNING

This product must be properly grounded.

• Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being

turned ON accidentally.

• Prior to servicing appliance, always disconnect

appliance electrical supply cord, if so equipped, from

wall receptacle. If appliance is hard-wired to power

supply, disconnect power to unit by turning off the

proper circuit breaker. Lock service panel to prevent

power from being turned ON accidentally.

• A neutral supply wire must be provided from the

power source (breaker) because critical range

components, including the surface burner spark re-

ignition module, require it to operate safely and

properly.

• Mount the receptacle securely to a wall stud, then seal

around the receptacle's housing.

Model Voltage Dedicated circuit Phase

Pxx305Wx 120 VAC 15 Amps Single

Pxx366Wx 120 VAC 15 Amps Single

Pxx364WDx 120 VAC 20 Amps Single

Pxx364WLx 120 VAC 20 Amps Single

Pxx486WDx 120 VAC 20 Amps Single

Pxx486WLx 120 VAC 20 Amps Single

• Power cord and receptacle

should protrude no more than

2'' (51 mm) from the rear wall.

NOTE: Plug styles may vary.

NEMA 5-15 NEMA 5-20

G

N

2"

(51)

When using a receptacle it may

be necessary to recess the

receptacle's housing into the rear

wall. Refer to Local Electrical

Code to determine the minimum

volume for all electrical / junction

boxes. Follow all local electrical

codes and ordinances, and/or the

National Electric Code, as

applicable.

Volt Circuit Frequency Phase

240/208 VAC 50 Amps 60 Hz. Single

2" (51) max.

La page charge ...

Thermador PRG364WLG Guide d'installation

Thermador PRG364WLG Guide d'installation

dans d''autres langues

Documents connexes

Autres documents