Samsung LN-T1954H Manuel utilisateur

Owner’s

Instructions

Register your product at www.samsung.com/global/register

Record your Model and Serial number here for future reference.

· Model __________ · Serial No. ____________

LN-T1953H

LN-T1954H

TFT-LCD TELEVISION

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care center.

Contacte con SAMSUNG WORLD-WIDE

Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con nuestro Servicio de

Atención al Cliente.

Country

Customer Care Center

Web Site Address

CANADA 1-800-SAMSUNG (7267864) www.samsung.com/ca

Samsung Electronics Canada Inc., Customer

Service 55 Standish Court Mississauga,

Ontario L5R 4B2 Canada

Samsung Electronique Canada Inc.,

Service à la Clientèle 55 Standish Court

Mississauga, Ontario L5R 4B2 Canada

U.S.A 1-800-SAMSUNG (7267864) www.samsung.com

Samsung Electronics America, Inc.

105 Challenger Road

Ridgefield Park, NJ 07660-0511

BN68-01184A-00

BN68-01184A-00-Cover.indd 1 2007-02-13 �� 1:43:03

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen

• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention.

This image retention is also known as "screen burn".

To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

• Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the

left, right and center of the screen caused by the difference of light emission on the screen.

Playing a DVD or a game console may cause a similar effect to the screen.

Damages caused by the above effect are not covered by the Warranty.

• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Précautions à prendre lors de l’affichage d’une image fixe

Une image fixe peut causer des dommages irrémédiables à l’écran du téléviseur.

• N’affichez pas une image fixe sur l’écran LCD plus de 2 heures. Cela pourrait provoquer une rémanence de l’image à l’écran.

Cette rémanence de l’image est également appelée “brûlure de l’écran”. Pour éviter une telle rémanence de l’image à l’écran,

réduisez la luminosité et le contraste de l’écran lorsque vous laissez une image fixe affichée

• Regarder l’écran LCD du téléviseur en format 4:3 pendant une longue période peut laisser des traces de

bordures à gauche, à droite et au centre de l’écran, à cause de la différence d’émission de lumière sur l’écran.

La lecture d’un DVD ou l’utilisation d’une console de jeu peut avoir un effet similaire sur l’écran. Les dommages

provoqués par les effets qui précèdent ne sont pas couverts par la garantie.

• L’affichage d’images fixes de jeux vidéo et d’ordinateurs pendant plus longtemps qu’une période spécifique peut provoquer des

rémanences.Pour éviter cela, réduisez la “luminosité” et le “contraste” lors de l’affichage d’images fixes.

Still-Fra.indd 1 2007-02-13 �� 2:01:42

Contents

Symbol Press Important Note One-Touch

Button

English

GENERAL INFORMATION

List of Features ................................................................. 2

Accessories ...................................................................... 2

Viewing the Control Panel ............................................... 3

Viewing the Connection Panel ......................................... 4

Remote Control ................................................................ 5

Installing Batteries in the Remote Control ........................ 6

CONNECTIONS

Connecting VHF and UHF Antennas ................................ 6

Connecting Cable TV ....................................................... 7

Connecting a VCR ............................................................ 8

Connecting a DVD Player/Set-Top Box ............................ 9

Connecting a DVD Player/Set-Top Box via HDMI ............ 9

Connecting a DVD Player/Set-Top Box via DVI ............. 10

Connecting a Digital Audio System ................................ 10

Connecting a PC .............................................................11

OPERATION

Turning the TV On and Off ............................................. 12

Plug & Play Feature ........................................................ 12

Changing Channels ........................................................ 13

Adjusting the Volume ...................................................... 14

Viewing the Display ........................................................ 14

Viewing the Menus ......................................................... 15

Memorizing the Channels ............................................... 15

To Select the Source ...................................................... 17

To Edit the Input Source Name ....................................... 17

PICTURE CONTROL

Using Automatic Picture Settings ................................... 18

Adjusting the Color Tone ................................................ 19

Setting the Film Mode ..................................................... 19

Freezing the Picture (depending on the model) ............. 19

Changing the Screen Size .............................................. 20

Viewing Picture-in-Picture .............................................. 21

HDMI Black Level ........................................................... 22

SOUND CONTROL

Customizing the Sound .................................................. 23

Using Automatic Sound Settings .................................... 23

Setting the TruSurround XT ............................................ 24

Choosing a Multi-Channel Sound (MTS) track - Digital . 24

Choosing a Multi-Channel Sound (MTS) track - Analog 25

Automatic Volume Control .............................................. 25

Selecting the Internal Mute ............................................. 26

Listening to the Sound of the Sub (PIP) Picture ............. 26

Resetting the Sound Settings to the Factory Defaults .... 27

Connecting Headphones ................................................ 27

Setting the On/Off Melody .............................................. 27

■

CHANNEL CONTROL

Selecting the Antenna ..................................................... 28

Clearing Scrambled Channels - Digital ........................... 28

Setting the Channel Lists ................................................ 29

To set-up Your Favorite Channels .................................. 30

Using the Channel Lists .................................................. 31

Viewing the Channel Lists .............................................. 31

Labeling Channels .......................................................... 32

LNA (Low Noise Amplier) .............................................. 32

Fine Tuning Analog Channels ......................................... 33

Checking the Digital-Signal Strength .............................. 33

PC DISPLAY

Using Your TV as a Computer (PC) Display ................... 34

Display Modes ................................................................ 34

Setting up the TV with your PC ...................................... 35

TIME SETTING

Setting the Clock ............................................................ 37

FUNCTION DESCRIPTION

Selecting a Menu Language ........................................... 40

Using the Game Mode .................................................... 40

Menu Transparency Level .............................................. 40

Viewing Closed Captions (On-Screen Text Messages)

- Analog ..........................................................................

41

Viewing Closed Captions (On-Screen Text Messages)

- Digital ...........................................................................

42

Setting the Function Help ............................................... 43

Setting the Light Effect ................................................... 43

Using the V-Chip ............................................................. 44

Digital Noise Reduction .................................................. 51

Upgrading the Software .................................................. 51

APPENDIX

Appendix ......................................................................... 52

Troubleshooting .............................................................. 52

Installing the Stand ......................................................... 54

Disconnecting the Stand ................................................. 54

How to Adjust the Stand ................................................. 55

Using the Decoration Covers .......................................... 55

Installing VESA compliant mounting devices .................. 55

Installing the Wall Mount Kit ........................................... 55

How to Adjust the Angle of the TV .................................. 55

Using the Anti-Theft Kensington Lock ............................ 56

Specications ................................................................. 56

■

English - 1

BN68-01184A-Eng.indd 1 2007-02-13 �� 1:33:22

English - 2

Accessories

Please make sure the following items are included with your LCD TV.

If any items are missing, contact your dealer.

Remote Control & Batteries (AAA x 2)

( LN-T1953H:BN59-00601A)

LN-T1954H:BN59-00608A

Power Cord

(3903-000085)

Wall Mount kit

(BN96-04960A)

Owner’s Instructions

Warranty Card / Registration

Card / Safety Guide Manual

(Not available in all locations)

Decoration Cover

LN-T1953H-Left: BN63-03216A,

Right: BN63-03217A

LN-T1954H-Left: BN63-03216B,

Right: BN63-03217B

Cleaning Cloth

(BN63-01798A)

The items color and shape may vary depending on the model.

General Information

List of Features

 Adjustable picture settings that can be stored in the TV’s memory.

 Automatic timer to turn the TV on and off.

 A special sleep timer.

 V-Chip function.

 Excellent Digital Interface & Networking :

With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Set-Top Box needed.

 Remote Control

The supplied remote can be used to operate the TV as well as most DVD players, Set-top boxes, Cable Boxes and

VCRs.

 SRS TruSurround XT

- SRS TruSurround XT provides a virtual Dolby surround system.

BN68-01184A-Eng.indd 2 2007-02-13 �� 1:33:23

English - 3

Viewing the Control Panel

1

SOURCE

Toggles between all the available input sources

(TV, AV, S-Video, Component, PC, HDMI).

In the on-screen menu, use this button as you would

use the ENTER button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3

+ VOL -

Press to increase or decrease the volume.

In the on-screen menu, use the + VOL - buttons as you

would use the ◄ and ► buttons on the remote control.

4 CH

Press to change channels.

In the on-screen menu, use the

CH

buttons as

you would use the ▲ and ▼ butons on the remote

control.

5

(POWER)

Press to turn the TV on and off.

POWER INDICATOR

Blinks and turns off when the power is on and lights up

in stand-by mode.

6

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

7

SPEAKERS

Buttons on the Lower Part of the Panel

The buttons on the side panel control your TV’s basic features, including the on-screen menu.

To use the more advanced features, you must use the remote control.

The product color and shape may vary depending on the model.

Front Panel buttons

Touch the right side of

each button to operate.

1

2

3

4

5

6

7

BN68-01184A-Eng.indd 3 2007-02-13 �� 1:33:24

English - 4

Viewing the Connection Panel

Rear Panel Jacks

Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.

For more information on connecting equipment, see pages 7-11.

1

AV IN

Video and audio inputs for external devices, such as a

camcorder or VCR.

S-VIDEO

Connect an S-Video signal from a camcorder or VCR.

2

DIGITAL AUDIO OUT (OPTICAL)

Connects to a Digital Audio component.

3

SERVICE / EX-LINK

Connector for service only.

4

HDMI/DVI IN / DVI IN (AUDIO R/L)

Connect to the HDMI jack of a device with an HDMI

output. Use the HDMI/DVI IN terminal for DVI connection

to an external device. You should use the DVI to HDMI

cable or DVI-HDMI adapter (DVI to HDMI) for video

connection, and the DVI IN ‘R-AUDIO-L’ terminal for

audio.

HDMI/DVI IN terminal does not support PC.

No sound connection is needed for an HDMI to HDMI

connection

5

HEADPHONE

Connects a set of external headphones for private

listening.

6

ANT 1 IN/ANT 2 IN

Connects to an antenna or cable TV system.

7

PC IN

Connects to the video and audio output jacks on

your PC.

8

COMPONENT IN

Connects Component video/audio.

9

POWER INPUT

Connects the supplied power cord.

0

KENSINGTON LOCK

The Kensington lock (not supplied) is a device used to

physically fix the system when used in a public place.

If you want to use a locking device, contact the dealer

where you purchased the TV.

The place of the Kensington Lock may be different

depending on its model.

BN68-01184A-Eng.indd 4 2007-02-13 �� 1:33:25

English - 5

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the

TV.

1

POWER

Turns the TV on and off.

2

NUMERIC BUTTONS

Press to change the channel.

3

–

Press to select additional channels(digital

and analog) being broadcast by the same

station. For example, to select channel

“54-3”, press “54”, then press “–” and “3”.

4

CH LIST

Used to display Channel Lists on the

screen.

5

ANTENNA

Press to select “AIR” or “CABLE”.

6

VOL / VOL

Press to increase or decrease the

volume.

7 (

MUTE)

Press to temporarily cut off the sound.

8

MENU

Displays the main on-screen menu.

9

S.MODE

Press to select the sound mode.

0

RETURN

Returns to the previous menu.

!

P.MODE

Press to select the picture mode.

@

SRS

Selects SRS TruSurround XT mode.

#

MTS

Press to choose stereo, mono or

Separate Audio Program

(SAP broadcast).

$

AUTO PROG.

Press to automatically store selected

TV/Cable channels.

%

ADD/DEL

Use to store and delete channels

to/from memory.

^

SOURCE

Press to display all of the available

video sources.

&

PRE-CH

Tunes to the previous channel.

*

FAV.CH

Press to switch to your favorite channels.

(

SLEEP

Press to select a preset time interval

for automatic ahut off.

)

CH

/ CH

Press to change channels.

a

EXIT

Press to exit the menu.

b

UP▲ / DOWN▼ / LEFT◄

/

RIGHT►

/ ENTER

Use to select on-screen menu items

and change menu values.

c

INFO

Press to display information on the TV

screen.

d

CAPTION

Controls the caption decoder.

e

STILL

Press to stop the action during a

particular scene.

Press again to resume normal video.

f

P.SIZE

Picture size selection.

g

PIP

Picture-in Picture ON/OFF.

h

CH

Displays the available channels in

sequence. (These buttons change

channels in the PIP window only.)

i

POSITION

Change the position of the PIP screen.

This is a special remote control for the visually impaired, and has Braille

points on the Power, Channel and Volume buttons.

BN68-01184A-Eng.indd 5 2007-02-13 �� 1:33:26

English - 6

1. Lift the cover at the back of the remote control upward as shown in the figure.

2.

Install two AAA size batteries.

Make sure to match the "+" and "–" ends of the batteries with the diagram inside the compartment.

3.

Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a

long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries should last for about one year.)

If the remote control doesn’t work, check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Installing Batteries in the Remote Control

Connecting VHF and UHF Antennas

ANT 2 IN

(CABLE)

ANT 1 IN

(AIR)

UHF

VHF

ANT 1 IN

(AIR)

UHF

VHF

Connections

If your antenna has a set of leads that look like the diagram to the right, see "Antennas with 300

Ω Flat Twin Leads" below.

If your antenna has one lead that looks like diagram to the right, see "Antennas with 75 Ω Round

Leads".

If you have two antennas, see "Separate VHF and UHF Antennas".

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter

(not supplied).

Use a screwdriver to tighten the screws.

2.

Plug the adaptor into the ANT 2 IN (CABLE) terminal on the back of the TV.

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or "rabbit ears") that has 300 Ω twin at leads, follow the directions

below.

1.

Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.

Antennas with 75 Ω Round Leads

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before con-

necting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

1.

Connect both antenna leads to the combiner.

2.

Plug the combiner into the ANT 1 IN (AIR) terminal on the bottom of the rear panel.

BN68-01184A-Eng.indd 6 2007-02-13 �� 1:33:27

English - 7

After you have made this connection, set the A/B switch to the "A" position for normal viewing. Set the A/B switch to the "B" position to

view scrambled channels. (When you set the A/B switch to "B", you will need to tune your TV to the cable box’s output channel, which is

usually channel 3 or 4.)

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-

way splitter, an RF (A/B) switch, and four lengths of RF cable. (These items are available at most electronics stores.)

2.

Connect this cable to a two-way splitter.

3. Connect an RF cable between the OUTPUT

terminal on the splitter and the IN terminal

on the cable box.

4. Connect an RF cable between the

ANT OUT terminal on the cable box and

the B–IN terminal on the RF(A/B) switch.

1. Find and disconnect the cable that is

connected to the ANT IN terminal on your

cable box.

This terminal might be labeled "ANT IN",

"VHF IN" or simply, "IN".

5. Connect another cable between the other

OUT terminal on the splitter and the A–IN

terminal on the RF (A/B) switch.

6. Connect the last RF cable between the

OUT terminal on the RF (A/B) switch and

the ANT IN terminal on the rear of the TV.

Splitter

Incoming

cable

Splitter

Cable Box

Incoming

cable

Splitter

Cable Box

RF (A/B)

Switch

Incoming

cable

ANT IN

Splitter

Cable Box

Incoming

cable

RF (A/B)

Switch

Splitter

Cable Box

Incoming

cable

TV Rear

RF (A/B)

Switch

ANT IN

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1.

Plug the incoming cable into the ANT 2 IN (CABLE) terminal on the back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

Connecting to a Cable Box that Descrambles All Channels

1. Find the cable that is connected to the ANT OUT terminal on your cable box.

This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".

2. Connect the other end of this cable to the ANT 2 IN (CABLE) terminal on the back of the TV.

ANT OUT

ANT IN

ANT 2 IN

(CABLE)

ANT 2 IN

(CABLE)

BN68-01184A-Eng.indd 7 2007-02-13 �� 1:33:29

English - 8

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 6-7). Skip step 1 if you have not yet connected to an antenna or a cable system.

1.

Unplug the cable or antenna

from the back of the TV.

2.

Connect the cable or antenna

to the ANT IN terminal on the

back of the VCR.

3. Connect an RF Cable between

the ANT OUT terminal on the

VCR and the ANT 1 IN (AIR) or

ANT 2 IN (CABLE) terminal on

the TV.

4. Connect a Video Cable

between the VIDEO OUT jack

on the VCR and the AV IN 1 (or

AV IN 2) [VIDEO] jack on the

TV.

5. Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN 1 (or AV IN 2)

[R-AUDIO-L] jacks on the TV.

If you have a “mono”

(non-stereo) VCR, use a

Y-connector (not supplied)

to hook up to the right

and left audio input jacks

of the TV. If your VCR

is stereo, you must

connect two cables.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

TV Rear Panel

RF Cable (Not supplied)

3

VCR Rear Panel

2

Video Cable (Not supplied)

4

Audio Cable (Not supplied)

5

ANT 1 IN

(AIR)

Your Samsung TV can be connected to an S-Video signal from an VCR.

(This connection delivers a better picture as compared to a standard VCR.)

1. To begin, follow steps 1–3

in the previous section to

connect the antenna or

cable to your VCR and

your TV.

2.

Connect an S-Video Cable

between the S-VIDEO OUT

jack on the VCR and the

AV IN1 [S-VIDEO] jack on

the TV.

3.

Connect Audio Cables

between the AUDIO OUT

jacks on the VCR and the

AV IN1 [R-AUDIO-L] jacks

on the TV.

An S-Video cable may be included with a VCR. (If not, check your local electronics store.)

Each VCR has a different back panel configuration.

When connecting a VCR, match the color of the connection terminal to the cable.

VCR Rear Panel

RF Cable (Not supplied)

1

Audio Cable (Not supplied)

3

TV Rear Panel

S-Video Cable (Not supplied)

2

ANT 2 IN

(CABLE)

S-Video Connecion

Video Connecion

BN68-01184A-Eng.indd 8 2007-02-13 �� 1:33:30

English - 9

DVD Player/Set-Top Box

TV Rear Panel

Component Cable (Not supplied)

1

Audio Cable (Not supplied)

2

DVD Player Rear Panel

TV Rear Panel

HDMI Cable (Not supplied)

Connecting a DVD Player/Set-Top Box

The rear panel jacks on your TV make it easy to connect a DVD player to your TV.

1.

Connect a Component

Cable between the

COMPONENT IN(1 or 2)

[Y, PB, PR] jacks on the TV

and the COMPONENT

[Y, PB, PR] jacks on the

DVD/Set-top Box.

2.

Connect Audio Cables

between the COMPONENT

IN(1 or 2) [R-AUDIO-L]

jacks on the TV and the

AUDIO OUT jacks on the

DVD/Set-top Box

Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and

Pr (Red) for enhanced video quality.

Be sure to match the component video and audio connections.

For example, if connecting the video cable to COMPONENT IN, connect the audio cable

to COMPONENT IN also.

Each DVD Player/STB has a different back panel configuration.

When connecting a DVD player/STB, match the color of the connection terminal to the

cable.

Connecting a DVD Player/Set-Top Box via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.

1.

Connect an HDMI Cable

between the HDMI/DVI IN

connector on the TV and the

HDMI connector on the DVD

player/Set-Top Box

What is HDMI?

• HDMI(High-Definition Multimedia Interface), is a next-generation an interface that

enables the transmission of digital audio and video signals using a single cable.

• The difference between HDMI and DVI is that the HDMI device is smaller in size,

has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.

Each DVD player/STB has a different back panel configuration.

BN68-01184A-Eng.indd 9 2007-02-13 �� 1:33:31

English - 10

Connecting a DVD Player/Set-Top Box via DVI

This connection can only be made if there is a DVI Output connector on the external device.

1.

Connect a DVI to HDMI

Cable or DVI-HDMI Adapter

between the HDMI/DVI IN

connector on the TV and the

DVI connector on the

DVD player/Set-Top Box.

2.

Connect Audio Cables

between the DVI IN

[R-AUDIO-L] jack on the

TV and the AUDIO OUT jacks

on the DVD player/

Set-Top Box.

Each DVD player/STB has a different back panel configuration.

When connecting a DVD player/STB, match the color of the connection terminal to

the cable.

When using an HDMI/DVI cable connection, you must use the HDMI/DVI IN terminal.

TV Rear Panel

DVD Player / Set-Top Box

Audio Cable

(Not supplied)

2

DVI to HDMI Cable (Not supplied)

1

Digital Audio System

TV Rear Panel

Optical Cable (Not supplied)

Connecting a Digital Audio System

1. Connect an Optical Cable

between the “DIGITAL

AUDIO OUT (OPTICAL)”

jacks on the TV and the

Digital Audio Input jacks on

the Digital Audio System.

When a Digital Audio

System is connected to the

“DIGITAL AUDIO OUT

(OPTICAL)” terminal:

Decrease the volume

of the TV, and adjust the

volume level with the

system’s volume control.

5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH.

Each Digital Audio System has a different back panel configuration. .

The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV.

BN68-01184A-Eng.indd 10 2007-02-13 �� 1:33:32

English - 11

PC

TV Rear Panel

D-Sub Cable (Not supplied)

1

PC Audio Cable (Not supplied)

2

Connecting a PC

1. Connect a D-Sub

Cable between PC IN

[PC] connector on

the TV and the PC

output connector on

your computer.

2.

Connect a PC Audio

Cable between PC IN

[AUDIO] jack on the

TV and the Audio Out

jack of the sound card

on your computer.

Each PC has a different back panel configuration.

When connecting a PC, match the color of the connection terminal to the cable.

BN68-01184A-Eng.indd 11 2007-02-13 �� 1:33:33

English - 12

Turning the TV On and Off

Press the POWER button on the remote control.

You can also use the button on the side of the panel.

Operation

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently:

1. Press the POWER button on the remote control.

The message “Menu language, Shop Mode, Channels and Time will be set.” is

displayed.

Press the ENTER button, then “Select the language of the OSD” menu is

automatically displayed.

2.

Press the ▲ or ▼ buttons to select language, then press the ENTER button.

The message “Select Home Mode when installing this TV at home.” is displayed.

3.

Press the ◄ or ► buttons to select “Shop” or “Home”, then press the

ENTER button.

The message “Select the antennas to memorize.” is displayed.

We recommend setting the TV to Home mode for the best picture in your

home environment.

Shop mode is only intended for use in retail environments.

If the unit is accidentally set to Shop mode and you want to return to Dynamic

(Home) mode, press any Volume button and then hold down the MENU button

for five seconds on the side panel of the TV.

4.

Press the ▲ or ▼ buttons to memorize the channels of the selected connection.

Press the ENTER button to select “Start”.

If the antenna is connected to ANT 1(AIR), select “Air” and if it is connected to

ANT 2 (CABLE), select “Cable”.

If both ANT 1 (AIR) and ANT 2 (CABLE) are connected, select the “Air + Cable”.

In Cable mode, you can select the correct signal source among STD, HRC,

and IRC by pressing the ▲ or ▼ button, then press the ENTER button.

Contact your local cable company to identify the type of cable system that

exists in your particular area.

5.

The TV will begin memorizing all of the available channels.

After all the available channels are stored, the Auto program menu reappears.

Press the ENTER button when channel memorization is complete.

The message “Select the clock mode.” is displayed.

To stop the search before it has finished, press the ENTER button with stop

selected.

6. Press the ENTER button.

Press the ▲ or ▼ buttons to select “Manual” or “Auto”, then Press the

ENTER button.

The message “Set to daylight savings time.” is displayed.

Select Home Mode when installing this TV at home.

Plug & Play

35%

Clock Set

Language

Plug & Play

English

Español

Français

Move Enter Skip

Shop

Stop

Menu language, Shop Mode,

Channels and Time will be set.

Start

Select the language of the OSD.

Home

Move Enter Skip

Select the antennas to memorize.

Start

Air

Plug & Play

Cable

Air+Cable

Start

Move Enter Skip

Enter Skip

Auto Program in progress.

Plug & Play

Skip

Auto Program is completed.

16 Channels were memorized.

Air : 16, Cable : 0.

Clock Mode :

Move Enter Skip

Select the clock mode.

Plug & Play

Auto

Manual

Air Channel 50

BN68-01184A-Eng.indd 12 2007-02-13 �� 1:33:36

English - 13

Changing Channels

1. Press the CH

or

CH

button to change channels.

When you press the CH

or

CH

button, the TV changes channels in

sequence.

You will see all the channels that the TV has memorized. (The TV must have

memorized at least three channels). You will not see channels that were either

erased or not memorized. See page 15 to memorize channels.

Using the Channel Buttons

1. Press the PRE-CH button.

The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one

channel, then use the number button to select the second channel. Then

use the PRE-CH button to quickly alternate between them.

Using the PRE-CH Button to select the Previous Channel

7. Press the ▲ or ▼ buttons to select “On” or “Off”, then Press the ENTER button.

The message “Select the time zone where you are located.” is displayed.

8. Press the ▲ or ▼ buttons to highlight the time zone for your local area.

Press the ENTER button. If you have received a digital signal, the time will be set

automatically.

If not, see page 38 to set the clock.

9.

The message “Enjoy your watching.” is displayed.

When you have finished, press the ENTER button.

If you want to reset this feature...

1. Press the MENU

button to display the menu.

Press the ▲ or ▼ buttons to select "Setup", then press the ENTER button.

2. Press the ENTER

button again, to select "Plug & Play".

3. The message "Menu language, Shop Mode, Channels and Time will be set."

is displayed.

Daylight Savings Time :

Move Enter Skip

Set to daylight savings time.

Plug & Play

On

Off

Move Enter Skip

Select the time zone where you are located.

Plug & Play

Newfoundland

Atlantic

Eastern

Central

Mountain

Pacific

Alaska

Hawaii

Enjoy your watching.

OK

Setup

Plug & Play ►

Language : English ►

Time

►

Game Mode : Off ►

V-Chip ►

Caption ►

Menu Transparency : High

►

▼More

TV

Move Enter Return

Menu language, Shop Mode,

Channels and Time will be set.

Start

BN68-01184A-Eng.indd 13 2007-02-13 �� 1:33:38

English - 14

Air 7

Mono

Picture Mode : Dynamic

Sound Mode : Custom

MTS : Stereo

Caption : On

V-Chip : On

05 : 54 pm

Adjusting the Volume

1. Press the

VOL

or VOL

buttons to decrease or increase the volume.

Using Mute

At any time, you can cut off the sound using the MUTE button.

1.

Press MUTE button and the sound cuts off.

The word " " will appear in the lower-left corner of the screen.

2.

To turn mute off, press the MUTE button again, or simply press the

VOL

or VOL

buttons.

Viewing the Display

1. Press the INFO button on the remote control.

The TV will display the channel, the type of sound,

and the status of certain picture and sound settings.

Press the INFO button once more or wait approximately 10 seconds and the

display disappears automatically.

The display identies the current channel and the status of certain audio-video settings.

BN68-01184A-Eng.indd 14 2007-02-13 �� 1:33:38

English - 15

Antenna : Air ►

Auto Program ►

Clear Scrambled Channel ►

Channel List ►

Name ►

Fine Tune ►

Signal Strength ►

LNA : On ►

Channel

Move Enter Return

TV

Channel

Move Enter Return

TV

Antenna : Air

Auto Program

Clear Scrambled Channel

Channel List

Name

Fine Tune

Signal Strength

LNA : On

Air

Cable

Move Enter Return

Mode : Dynamic

►

Contrast 100

Brightness 45

Sharpness 75

Color 55

Tint G 50 R 50

Color Tone : Cool1

►

▼More

PictureTV

Viewing the Menus

1. With the power on, press the MENU button.

The main menu appears on the screen. The menu’ s left side has five icons:

Picture, Sound, Channel, Setup, Input.

2.

Use the ▲ or ▼ buttons to select one of the five icons.

Then press the ENTER

button to access the icon’s sub-menu.

3.

Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

Memorizing the Channels

Your TV can memorize and store all of the available channels for both "off-air" (Air) and "Cable" channels. After the available

channels are memorized, use the CH

or

CH

buttons to scan through the channels. This eliminates the need to change

channels by entering the channels digits. There are three steps for memorizing channels: selecting a broadcast source, memoriz-

ing the channels (automatic) and adding or deleting channels (Channel Lists).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to

the TV (i.e. an Air or a Cable system).

1.

Press the MENU button to display the menu.

Press the ▲ or ▼ buttons to select "Channel", then press the

ENTER

button.

2.

Press the ENTER button select “Antenna”.

Press the ▲ or ▼ buttons to select “Air” or “Cable”, then press the ENTER button.

Press the EXIT

button to exit.

BN68-01184A-Eng.indd 15 2007-02-13 �� 1:33:40

English - 16

Move Enter Return

Antenna : Air ►

Auto Program

►

Clear Scrambled Channel

►

Channel List ►

Name

►

Fine Tune

►

Signal Strength

►

LNA : On

►

Channel

Move Enter Return

TV

Move Enter Return

Select the antennas to memorize.

Auto Program

Move Enter Return

TV

Start

Air

Cable

Air+Cable

Start

Plug & Play

Enter Return

Auto Program is completed.

25 Channels are memorized.

Air : 18, Cable : 7.

Auto Program

Cable 50

50%

Stop

Enter Return

Auto Program in Progress.

Move Enter Return

Selects a cable signal type for your location.

Auto Program

Move Enter Return

TV

Analog

Start

STD

HRC

IRC

Digital

Storing Channels in Memory (Automatic Method)

1.

Press the MENU button to display the menu.

Press the ▲ or ▼ buttons to select “Channel”, then press the ENTER button.

2.

Press the ▲ or ▼ buttons to select "Auto Program", then press the ENTER

button.

3.

Press the ▲ or ▼ buttons to select the antenna connection, then press the

ENTER button.

Air: “Air” antenna signal. / Cable: “Cable” antenna signal. /

Air+Cable: “Air” and “Cable” antenna signals.

4.

When selecting the Cable TV system: Press the ENTER button to start the auto

program. By default, the cable TV system is set to “STD”. If you want to select

another type of cable system, press the ▲ or ▼ button to select “STD”, “HRC” or

“IRC”.

STD, HRC and IRC identify various types of cable TV systems. Contact your

local cable company to identify the type of cable system that exists in your

particular area. At this point the signal source has been selected.

Press the ENTER

button to start the auto program.

To stop the search before it has finished, press the ENTER button with stop

selected.

5.

After all the available channels are stored, the “Auto Program” menu reappears.

Press the EXIT button to exit.

STD

HRC

IRC

BN68-01184A-Eng.indd 16 2007-02-13 �� 1:33:43

English - 17

To Select the Source

Use to select TV or other external input sources connected to the TV.

Use to select the input source of your choice.

1.

Press the MENU button to display the menu.

Press the▲ or ▼ buttons to select “Input”, then press the ENTER button.

2.

Press the ENTER

button to select "Source List".

Press the ▲ or ▼ buttons to select signal source, then press the ENTER

button.

When you connect equipment to the LCD, you can choose between the

following sets of jacks: TV, AV, S-Video, Component, PC, HDMI on the TV’s rear

panel.

HDMI input can only be selected when the external device is turned on and

connected via HDMI.

You can choose only those external devices that are connected to the TV.

Press the SOURCE button on the remote control to view an external signal source.

To Edit the Input Source Name

Name the device connected to the input jacks to make your input source selection easier.

1. Press the MENU button to display the menu.

Press the▲ or ▼ buttons to select “Input”, then press the ENTER button.

Press the ▲ or ▼ buttons to select "Edit Name", then press the ENTER

button.

2.

Press the ▲ or ▼ buttons to select "AV", "S-Video", "Component", "PC", "HDMI"

input jack, then press the ENTER

button.

3.

Press the ▲ or ▼ buttons to select "VCR", "DVD", "D-VHS", "Cable STB",

"HD STB", "Satellite STB", "PVR STB", "AV Receiver", "DVD Receiver",

"Game", "Camcorder", "DVD Combo", "DVD HDD Recoder", "PC",

"Internet TV Recv.","Interactive TV Recv.","VOD STB", "TV" input source, then

press the ENTER

button.

Press the EXIT button to exit.

Input

Source List : TV ►

Edit Name

►

TV

Move Enter Return

Source ListTV

Move Enter Return

TV

AV : ----

S-Video : ----

Component : ----

PC : ----

HDMI : ----

Input

Source List : TV ►

Edit Name

►

TV

Move Enter Return

Edit NameTV

Move Enter Return

AV

: ---- ►

S-Video : ----

Component

: ---- ►

PC

: ---- ►

HDMI : ---- ►

Edit NameTV

Move Enter Return

AV

: ---- ►

S-Video

: ---- ►

Component

: ---- ►

PC

: ---- ►

HDMI : ---- ►

----

VCR

DVD

D-VHS

Cable STB

HD STB

Satellite STB

▼

BN68-01184A-Eng.indd 17 2007-02-13 �� 1:33:45

English - 18

100

▲

Contrast

▼

Move Adjust Return

Using Automatic Picture Settings

Your TV has Three automatic picture settings ("Dynamic", "Standard", "Movie") that are preset at the factory.

You can activate either Dynamic, Standard, Movie by making a selection from the menu.

1.

Press the MENU button to display the menu.

Press the ENTER

button, to select "Picture".

2.

Press the ENTER

button to select "Mode".

Press the ▲ or ▼ buttons to select the "Dynamic", "Standard", "Movie" picture

setting. Press the ENTER

button.

 Choose Dynamic to increase the clarity and sharpness of the picture.

 Choose Standard for the standard factory settings.

 Choose Movie for a natural Image without picture enhancements.

3. Press the ▲ or ▼ buttons to select "Contrast", "Brightness", "Sharpness",

"Color", or "Tint(G/R)", then press the ENTER

button.

4.

Press the ◄ or ► buttons to decrease or increase the value of a particular item.

For example, if you select "Contrast", pressing the ► button increases it.

Press the EXIT

button to exit.

• When you make changes to Contrast, Brightness, Sharpness, Color, Tint(G/R)

OSD will be also adjusted accordingly.

• When in PC mode, Tint, Sharpness, and Color are not available.

Picture Control

Press the P.MODE button on the remote control

repeatedly to select the desired picture mode.

Move Enter Return

Mode : Dynamic

►

Contrast 100

Brightness 45

Sharpness 75

Color 55

Tint G 50 R 50

Color Tone : Cool1

►

▼More

PictureTV

Move Enter Return

Mode : Dynamic

Contrast 100

Brightness 45

Sharpness 75

Color 55

Tint G 50 R 50

Color Tone : Cool1

▼More

PictureTV

Dynamic

Standard

Movie

Move Enter Return

Mode : Dynamic

Contrast 100

Brightness 45

Sharpness 75

Color 55

Tint G 50 R 50

Color Tone : Cool1

▼More

PictureTV

BN68-01184A-Eng.indd 18 2007-02-13 �� 1:33:47

La page charge ...

Samsung LN-T1954H Manuel utilisateur

Ce manuel convient également à

Samsung LN-T1954H Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents