2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable
standards. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions
manual, may cause interference to radio communications. It has been tested
and found to comply with limits for a Class A digital device pursuant to
subpart B of Part 15 of FCC Rules, which are designed to provide reasonable
protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference
in which case the user at his own expense will be required to take whatever
measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any
person other than the authorized technicians. The user should consult his/her
dealer for the problem happening. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no
means responsible for any damage or hazard caused by improper application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，
在此種情況下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to
be present.
3
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant
accueillir des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a
safeguard (for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler
une sauvegarde (par exemple, dans le cas de certains types de batterie
au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des
températures extrêmement élevées pouvant entraîner une explosion ou
la fuite de liquide ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之
電池。
4
Product Features
Standard Features
System
Intel Skylake-U Core i5-6360U Processor
Mechanical Structure
Fanless structure with Aluminum die-cast main unit casing
Water resistant structure allowing easy cleaning
Foldable base
Display
High-quality 15” TFT active matrix LCD monitor provided with true-flat
Projected Capacitive touch panel supporting 10-point multi-touch
Optional Items
System
1 x DDR4 SO-DIMM slot memory
Windows POSReady 7, Windows 7, Windows Embedded Industry 8.1
64-bit, Windows 10 IoT 64-bit for Skylake platform
Wireless Communication
WiFi + BT module, through M.2 Interface
Connection Cable
RJ50-to-DB9 serial port conversion cable
Split cable for 2 cash drawer control
Base
GEN 8E base including poweredUSB board, and supporting
60W/80W/150W power adaptor
Integration Kit
Integrated side mount upgrade kits, such as SA-105 provided with
optional MSR, SA-205 provided with iButton, SA-305, and SA-405
1 x M.2 2280 + 1 x SATA for storage. SATA port is reserved for 2.5”
HDD/SSD accessible from service window. Storage device is located in
the base.
PoweredUSB kit in GEN 8E base stand, such as PU-480 or PU-490
Power adapter kits for 80W/150W power adapters
Back mount displays, such as LM/TM or PD series models.
5
Views of the XT-6015C
Front and Rear Views of Terminal with Gen 7E Base Stand
Left Side View of Terminal with Gen 7E Base Stand
Bottom View of Terminal with GEN 7E Base Stand
Neck Cover
DDR4 Memory Cover
LCD Touch Panel
Power Indicator
Base Stand
Hinge
for main unit
Cable Exit
Cable Cover
Bottom Plate
Rubber Cushion
Wrapping Screw
Power Button
Brightness Adjustment
Button “+”
Brightness Adjustment
Button “-”
USB 2.0 Port
Locking Hook
6
Front and Rear Views of Terminal with GEN 8E Base Stand
Left Side View of Terminal with GEN 8E Base Stand
Bottom View of Terminal with GEN 8E Base Stand
Power Button
Brightness Adjustment
Button “+”
Brightness Adjustment
Button “-”
USB 2.0 Port
Locking Hook
DDR4 Memory Cover
LCD Touch Panel
Power Indicator
Base Stand
Hinge
for main unit
Cable Exit
Neck Cover
Cable Cover
Rubber Cushion
Wrapping Screw
PoweredUSB Board Cover
Bottom Plate
Power Adaptor Chamber
7
Views of I/O Interfaces of Terminal
1
DC-IN Power Jack
5
USB 2.0 Port
2
CR Port
6
USB 3.0 Port
3
RJ50 COM Port
7
LAN Port
4
VGA Port
-
-
Positioning your POS for a Perfect Viewing Angle
The adjustable bases designed for XT-6015C come in two models, Gen 7E/8E,
and allow you to determine an ideal position for your terminal by using its
unique tilt adjustment mechanism. As the below figures suggest, both bases
provide three standard positioning solutions for your terminal: Flat Folded
mode, Low Profile mode, and Full Extended mode.
XT-6015C with Gen 7E Base
Flat Folded mode
Low Profile mode
Full Extended mode
XT-6015C with Gen 8E Base
Flat Folded mode
Low Profile mode
Full Extended mode
3
5
6
2
4
7
1
8
In general, XT-6015C will be set up beforehand in Flat Folded mode and then
packaged into the box for shipping. After it is unpacked, you may re-adjust the
terminal in either Low Profile mode or Full Extended mode according to
your situation. Below will provide instructions on how to adjust the specific
base connected to the POS system. As a reminder, please be careful not to
touch the LCD panel while setting up the tilt angle.
XT-6015E with Gen 7E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-6015C with Gen 7E
base.
1. Unpack XT-6015C, which is supposed to be
set in flat folded mode, out of the package
box and then lay your POS system on a flat
surface.
2. Steady the base with one hand, and then tilt
the screen downwards.
3. Position your terminal in Full Extended mode
3.1 After grabbing the bottom edge of the screen with your hand, gently
move the screen upward until the screen is locked into place with a
click sound.
9
3.2 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
3.3 With the screen facing toward you, tilt the
screen up or down to your desired angle.
Please do not press on the LCD panel while
setting up the tilt angle.
3.4 Remove the cable cover from the base.
3.5 Fix the base with two #/6/32-14L screws.
Lever
Lower
hook
10
4. Return your terminal back to Flat Folded mode from Full Extended
mode.
4.1 Remove the cable cover from the base.
4.2 Remove the two screws from the base.
4.3 Tilt your screen in a horizontal position.
Remove the two screws.
11
4.4 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, move the display downwards
until the lever is lifted off the hook as shown in the figure.
4.5 Push the cable cover back.
4.6 Tilt the screen again to the horizontal
position.
Hook
Lever
12
5. Position the terminal in Low Profile mode.
5.1 Follow Step 4 to set up the termimal in Flat
Folded mode.
5.2 Tilt the screen all the way down
5.3 To tilt screen up or down to your desired
angle, please be advised to keep the base
steady with one hand to do so. Do NOT
press on the LCD panel while setting up the
tilt angle.
XT-6015C with Gen 8E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-6015C with Gen 8E
base.
1. Unpack XT-6015C, which is supposed to
be set in flat folded mode, out of the
package box and then lay your POS
system on a flat surface.
2. While steadying the terminal with your
hand holding onto the base, tilt the screen
down.
13
3. Push the cable cover outwards to remove
it from the base.
4. Position your terminal in Full Extended mode.
4.1 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
4.2 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the tilt
angle.
Lower
hook
Lever
14
4.3 Fix the base with two #/6/32-14L screws.
4.4 Push the cable cover back.
5. Position the terminal in Low Profile mode.
5.1 While keeping your terminal steady with your hand holding on to
the base, tilt your terminal down. Then, remove the cable cover
from the base.
15
5.2 Remove the two screws from the base.
5.3 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display
upwards or downwards until the lever is snapped into the upper
hook to lower the screen as shown in the below figure.
5.4 Push the cable cover back.
5.5 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the
tilt angle.
Lever
Upper
hook
Remove the two screws.
16
6. Return the terminal back to Flat Folded mode.
6.1 While steadying your terminal with your hand holding onto the
base, tilt your screen up.
6.2 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, release the lever back to the
point above the upper hook as shown in the figure.
6.3 Push the cable cover back.
6.4 Tilt the screen to the horizontal position.
Lever
Upper
hook
17
Installing Power Adapter Kit onto GEN 8E Base Stand
The power adapter kit is optional and, before shipping, is installed onto the
optional GEN 8E base stand. Upon your needs, you can purchase and install
the kit for 80W or 150W power adapter. The introduction to the kit and the
brief description of installation of the kit are made below.
For the detailed description of installation of the 80W/150W power adapter kit,
refer to the XT-6015C technical manual.
Secure the Power Cord
To avoid the power cord from being pulled out accidentally,
the power adapter kits are shipped with a power cord bracket.
After installing the power adapter kit and connecting the
power cord to the power adapter, remember to use the power
cord bracket to secure the power cord.
Connecting Power Cable Connector to the Terminal
Before turning turn ON the terminal, connect the power cable connector to the
power jack of the terminal.
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Fixing with screw
18
Powering ON the XT-6015C
After connecting the power cable to the power jack
of main unit, slightly push to open the power
button cover at the left side of the main unit.
Then press the power button to power on the main
unit. To power it off, press the button again.
Once powering off the system, if you want to
power it on again, please wait for at least 3
seconds.
If the system hangs due to a reason, such as software resource conflict, please
press and hold the power button for 10 seconds around to forcedly shut down
the system.
Power Indicator
There is a power LED indicator serving for several
purposes located at the center of lower rim of LCD
panel. The relationship between the indicator status
and other conditions is summarized below:
Indicator Status
System Status
External Power
Powering Up
Off
Off
Off
Not possible
Off
Off
Off
Not allowed
Green
Off
On
Allowed
Blue
On
On
N/A
Blue/Flash
On
Off
Green/Rapid Flash
On
Off
Installing an Operating System
This product is highly professional equipment. Therefore, we do NOT
encourage you to install any operating system into this machine. Posiflex
Technology, Inc. shall not be responsible for any technical support to questions
on this aspect. We suggest that you contact your dealer for OS installation.
19
Specifications
XT-6015C
CPU
Intel Skylake-U Core i5-6360U Processor
Memory
1 x DDR4 SO-DIMM slot
OS
Windows POSReady 7, Windows 7, Windows Embedded Industry 8.1
64-bit, Windows 10 IoT 64-bit for Skylake platform
TPM
Yes (optional)
Display
15-inch TFT LCD monitor (1024x768) with true-flat PCAP touch panel
Storage
1 x M.2 2280 + 1 x SATA + power connector
SATA port is reserved for 2.5” SSD/HDD accessible from service
window. Storage device is located in the base.
Ethernet
10/100/1000 Mb x 1 port
WLAN
1 x M.2 WiFi + BT module (optional)
Power
Supply
12 VDC power adaptor, 60W
Display Port
1 x VGA port, 12V power support by jumper setting
Serial port
3 x RJ50, RJ-50-to-DB9 cable (Optional)
RS-232 signal only. Jumper selectable 5V/12V support on all COM ports
CR Port
1 port, available for controlling 2 CR.
USB Port
Standard, 4 ports on the I/O plate (3 x USB 2.0, 2 x USB 3.0), 1 port on
the left side (USB 2.0), 3 USB headers reserved for internal USB device
use
Audio
Built-in 2W audio speaker
Extension
slot
1 x M.2 2230
Mechanical
installation
Desktop with base stand
Power LED
Indicator
Power ON/ standby, bi-color LED indicators
Temp &
Humidity
Operation Temp.: 0 to 40 ℃ / Storage Temp.: -20 to 60℃
Humidity: 10 to 90 %; 5 to 90 % (operation condition)
※ The product information and specification are subject to change without prior notice.
To get the detailed information on XT-6015C, please check this model from Posiflex
Global Website
(http://www.posiflex.com/en-global/Download/download).
20
<MEMO>
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Posiflex XT-6015C Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Posiflex XT-6015C User manual
Documents connexes
-
Posiflex XT-6315/6315E/6515/6515E Manuel utilisateur
-
Posiflex XT-6015C Manuel utilisateur
-
-
Posiflex RT-5115 Manuel utilisateur
-
-
Posiflex XT-6317/6517 Manuel utilisateur
-
-
-
-