2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable standards.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart B of Part 15 of FCC Rules,
which are designed to provide reasonable protection against interference when
operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference in which case the user at his own expense will
be required to take whatever measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
résidentiel, cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person
other than the authorized technicians. The user should consult his/her dealer for the
problem happening. Warranty voids if the user does not follow the instructions in
application of this merchandise. The manufacturer is by no means responsible for
any damage or hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une
personne autre que les techniciens autorisés. L'utilisateur doit consulter son
revendeur pour le problème qui se produit. La garantie s'annule si l'utilisateur ne
suit pas les instructions d'application de cette marchandise. Le fabricant n'est en
aucun cas responsable de tout dommage ou danger causé par une mauvaise
application.
警告使用者
3
這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這
種情況下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be
present.
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir
des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a safeguard
(for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler une
sauvegarde (par exemple, dans le cas de certains types de batterie au
lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des températures
extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide
ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電
池。
4
Views of RT-1016A
Front View
Rear View
Bottom View
P-Cap Touch Panel
LED indicator
Camera (Optional)
5
Right-Side View
Views of RB-5000 UPS Base Stand (Option for RT Series Model)
Top View Bottom View
When the AC power is turned off, the RT terminal will begin to be
powered by the UPS battery and the RB-5000 will beep once every
three seconds. At this time, back up the data on the terminal
immediately and power off the RT terminal.
When the AC power is turned off, if the UPS battery is very low, the
RB-5000 will beep once every second. At this moment, power off the
RT terminal immediately.
To get more detailed information of RB-5000, please contact the service team
of Posiflex or download the RB-5000 user manual from Posiflex Global
Website: (http://www.posiflex.com/en-global/Download/download).
BATT.
DC OUT
DC IN
Rubber Foot
Battery Cable
Screw Hole
Through Hole
6
View of I/O Interface of RT-1016A
Bottom Side
Left Side
Positioning your POS for a Perfect Viewing Angle
Steady the base with one hand, and then tilt the screen
in the direction shown by the arrow in the figure.
Please do NOT press on the LCD panel while
setting up the tilt angle.
Installing Power Adapter and Cables
The following provides instructions required to install your cables.
1. Lay the terminal with its rear facing
towards you and tilt the screen all the way
down.
DB9 COM Port
CR Port
LAN Port
DC IN Power Connector
RJ50 COM Port
USB 3.0 Port
USB 2.0 Port
USB 2.0 Ports
Micro USB Port
HDMI Port
SD Card Slot
7
2. Remove the system back cover.
2.1 If the system back cover is fire-resistant, first locate the screw as
indicated in the figure, and then remove it.
2.2 Hold down the release lever at the bottom of
the system back cover and then pulling the
cover outwards.
3. To remove the stand cover from the base, grab the top side of the
cover, (1) lift the stand cover up gently, (2) pull it at a 45 degree
angle, and then (3) slide it in the horizontal direction shown by the
arrow.
4. Connect the connector of the power adapter
to the DC-IN power jack. If necessary,
properly insert other cables into the correct
port.
1
2
3
Screw for Fire-Resistant
System Back Cover
8
5. Neatly arrange the cables. Locate the cable holder inside the base as
shown in the figure. Push down the lever to release if from the hook,
pass the cable through cable holder, and then press down the lever
again to lock it onto the hook.
6. Make sure the cord can be held into place
and passed through the cable exit after
sliding back the stand cover.
7.
7.1 Place back the sytem back cover. Make sure
it is well locked into place with a click sound.
7.2 For the fire-resistant system back cover, please insert another
screw into the screw hole indicated in the figure, and secure it.
8. Make sure the cable could be pulled out of
the cable exit from the bottom of the base.
Cable holder
Screw for Fire-Resistant
System Back Cover
9
Cable connectors like the connector of LAN cable have to be gently inserted
until a click sound is given. It is recommended that the I/O ports, such as COM
(DB9) port and VGA port, should be fastened with connector thumb screws
after the I/O cable connectors are completely connected. And please make sure
that each connector has to be connected to the right peripheral device in the
right way.
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables, which is considered as an artificial
damage and is not covered by the warranty. The means of power cord
should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Installing Optional Upgrade Kits and Peripherals
RT-1016A is an expandable model which allows you to upgrade its own
capacity by additionally installing multiple peripheral devices, such as
magnetic stripe reader (MSR), fingerprint or iButton sensors, and 2
nd
POS
monitor, according to your preference. The following will give you brief
instructions on how to expand on your current POS system with these optional
upgrade kits. Before proceeding with the installation of peripherals, please
make sure the POS system is completely shut down to prevent damage.
Installing Side Mount Upgrade Kits
Located at left side on the back of your system
unit, side mount compartment is mainly used for
installation of side-mounted equipment, such as
magnetic stripe reader. For detailed installation
instructions, please refer to the user manual
specific to the device which you intend to
mount onto the terminal.
Installing Rear-Mount POS Monitor
10
RT-series POS terminal also allows you to
additionally install rear-mount POS monitor to
expand its functionality. Regarding the step-
by-step instructions which aim to help you
mount it onto your POS system, Please refer
to the user manual specific to the device you
intend to install.
Installing PoweredUSB or USB Hub
Please go through the below steps to complete the installation of
PoweredUSB or USB hub.
1. After tilting the screen all the way down, remove the system back
cover.
1.1 If the system back cover is fire-resistant, first locate the
screw as indicated in the figure, and then remove it.
1.2 Hold down the release lever at the
bottom of the system back cover and
then pulling the cover outwards
2. To remove the stand cover from the base, grab the top side of the
cover, (1) lift the stand cover up gently, (2) pull it at a 45 degree
angle, and then (3) slide it in the horizontal direction shown by the
arrow.
3
2
1
Screw for Fire-Resistant
System Back Cover
11
3. Align the two screw bolts at the bottom of PoweredUSB or USB hub
with rail slots in the base.
4.
Push PoweredUSB or USB hub in the
direction shown by the arrow to lock it
into place.
To remove the PoweredUSB or USB hub from the rail slots, press
down the hubs first and then push it outwards.
5. Install power adaptor extension cable, USB cable, and power adaptor
for PoweredUSB hub.
5.1 Insert one end of the provided power
adaptor extension cable to DC Input port
of PoweredUSB hub and another end to
DC-in power jack of the terminal.
5.2 Insert mini-USB connector of the USB
cable to PoweredUSB hub and another
end to USB3.0 port of the terminal.
5.3 Connect the connector of the power
adapter to DC Output port of
PoweredUSB hub, and the other end to the
electrical outlet.
12
6. To Install USB cable for USB hub, Plug
Type-A connector of USB cable to USB
Port of USB hub and the other end of USB
cable to USB3.0 port of the POS terminal.
7. Neatly arrange your cable and then slide
back the stand cover.
8. .
8.1 Place back the sytem back cover. Make sure it
is well locked into place with a click sound
8.2 For the fire-resistant system back cover, please insert another
screw into the screw hole indicated in the figure, and secure it.
Status LED Indicator
LED status indicator, which is located at the bottom edge of the LCD panel, is
mainly responsible for notifying users of the current system status by emitting
various LED signals. In the chart provided below, it describes all the possible
LED status as a quick reference.
LED Status
Description
Off
System power OFF
Orange
System standby
Blue
System power ON
Screw for Fire-Resistant
System Back Cover
13
Powering ON/OFF RT-1016A
Power ON RT-1016A
Press down the power button to power on the POS.
Power OFF RT-1016A
In most cases, press the power button of the POS to power
the system off. If the terminal fails to turn off the machine
for unknown reasons, please be advised to hold the power
button more than 10 seconds to force a shutdown of the
system.
Operation Environment
To prevent RT-1016A from overheating, it is suggested to position your
terminal in a well-ventilated working environment. In doing so, please be
advised to keep the POS terminal at least 25mm away from other devices to
ensure the machine is properly cooled down and functioning normally.
Specifications
RT-1016A
CPU
Rockchip RK3399
System Memory
2GB / 4GB onboard
Storage Device
16GB / 32GB /64GB eMMC onboard + micro SD
slot
OS
Android 9.0
Power Supply
1 x 12V DC-in jack, 4-pin (12V/40W)
LCD Panel
15.6" TFT LCD with LED backlight
LCD Resolution
1920 x 1080
Touch
P-CAP touch with multi-touch support
Serial Port
2 ports, DB9 x 1+ RJ-50 x 1
External USB
Port
5 ports, USB3.0 x 1+ USB2.0 x 4
Internal USB
Port
3 x USB2.0 (pin header)
OTG USB
1 x micro USB
LAN Port
1 x 10/100/1000 Mb
Display Port
1 x VGA (internal connector) + 1 x HDMI
(for 2
nd
display, VGA connector and HDMI port
can’t be used at the same time)
CR Port
1 port, controlling 2 CR, 24V power support only
Power
Button
14
Audio Port
1 x 2W speaker
Extension Slot
1 x mini-PCIe slot
Wireless
Connectivity
Wifi via mini-PCIe expansion slot or USB
Power Button
1 x power button
Reset Button
1 x reset button
Dimension
(W x V x D in mm)
402 x 251 x 41.2 (without base)
Environmental
Requirements
Operating：0°C 〜 40°C, 20%RH - 90%RH
Storage：-20°C 〜 70°C, 10%RH - 90%RH
Regulation Rules
FCC/CE
Attachment
RA-101
Slim MSR attachment for RT series
RA-103
iButton (or RFID) with one USB port attachment
for RT series
RA-104
2D scanner attachment for RT series
RA-301
3-in-1 MSR + Fingerprint Sensor + 2D scanner
attachment for RT series
LM/TM-4010
9.7" 2nd display for RT series terminal
LM/TM-4011
10.1" 2nd display for RT series terminal
LM/TM-4015
15" 2nd display for RT series terminal
PU-460
PoweredUSB module to support 12Vand 24V
Powered USB ports
RT-560
USB port replicator ( USB2.0 x 4, installed in base
stand)
RB-5000
UPS battery stand
※ The product information and specifications are subject to change
without prior notice. To get the detailed information on the RT-1016A,
please check this model from Posiflex Global Website.
15
<MEMO>
16
<MEMO>
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
dans d''autres langues
- English: Posiflex RT-1016A User manual
Documents connexes
-
Posiflex RT-1016A Manuel utilisateur
-
-
-
Posiflex RT-5015E Manuel utilisateur
-
-
-
-
-
-