1
Package Contents
POS Monitor ……………………….(x1)
Power Adaptor……………………...(x1)
Power Cable (for HS/PS System)......(x1)
HDMI Cable...………………………(x1)
USB (Type B) Cable………………..(x1)
(For touch monitor and camera only)
Mounting Kits (for HS/PS System)...(x1)
User Manual………………………...(x1)
19640906010 Ver. A0
http://www.posiflex.com
LM-4010HDMI/TM-4010HDMI
LM-4011HDMI/TM-4011HDMI
POS Monitor User Manual
2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable standards. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A
digital device pursuant to subpart B of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
résidentiel, cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other
than the authorized technicians. The user should consult his/her dealer for the problem
happening. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne
autre que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le
problème qui se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions
d'application de cette marchandise. Le fabricant n'est en aucun cas responsable de tout
dommage ou danger causé par une mauvaise application.
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情
況下，使用者會被要求採取某些適當的對策。
3
Views of LM-4010HDMI/TM-4010HDMI/LM-
4011HDMI/TM-4011HDMI
Front View
Rear View
Bottom View
Introduction to the I/O Ports
DC-IN Power Jack
USB (Type-B) Port
HDMI Port
VGA Port
Camera (Optional)
LM-401xHDMI LCD Panel
TM-401xHDMI P-CAP Touch Panel
VESA-Mount Screw Holes
I/O Ports
Status LED Indicator
4
Connecting LM-4010HDMI/TM-4010HDMI/LM-
4011HDMI/TM-4011HDMI to a HS-series POS Terminal
Before connecting your POS monitor to a HS-series POS terminal, please
enable the power supply from the POS terminal to your POS monitor by
setting up the jumper of the POS terminal. It is suggested that professional
technicians implement the POS terminal jumper setting. To get more detailed
information on jumper setting, contact directly your local service center.
During connection, please ensure the terminal is properly powered off and
disconnected from the power sources to avoid potential hazards.
To connect your monitor to a HS-series POS terminal, please follow the below
instructions.
1. Remove the top I/O cover of your HS terminal.
2. Fix your LM/TM-series monitor to the HS terminal with 4 #6/32-8L
screws.
Top I/O Cover
5
3. Connect the HDMI cable, power cable, and USB cable (only for camera
and touch screeen) to your LM/TM-series monitor and the HS series
terminal. Put the cable cover back to the HS series terminal. Please refer
to the cable introduction on P.7.
6
Connecting LM-4011HDMI/TM-4011HDMI to a PS-series
POS Terminal
Before connecting your POS monitor to a PS-series POS terminal, please
enable the power supply from the POS terminal to your POS monitor by
setting up the jumper of the POS terminal. It is suggested that professional
technicians implement the POS terminal jumper setting. To get more detailed
information on jumper setting, contact directly your local service center.
During connection, please ensure the terminal is properly powered off and
disconnected from the power sources to avoid potential hazards.
To connect your monitor to a PS-series POS terminal, please follow the below
instructions.
1. There is four screw holes on the rear side of the PS-series POS terminal.
2. Fix your LM/TM-4011HDMI to the PS-series POS terminal with four
#6/32-10L screws
3. Connect the HDMI cable, power cable, and USB cable (only for camera
and touch screeen) to your LM/TM-series monitor and the PS series
terminal. Put the cable cover back to the PS series terminal. Please refer to
the cable introduction on P.7.
7
Power Cable
HDMI Cable
USB (Type B) Cable
(For touch monitor and camera only)
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
Connect to POS Terminal
Connect to POS Monitor
Connect to POS Terminal
Connect to POS Monitor
Connect to POS Terminal
Connect to POS Monitor
8
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Identifying your Monitor as Secondary Touchscreen Monitor
in Extended Mode
In the following section, the related descriptions will be offered to help you set
up TM series as the extended monitor when you attempt to extend the desktop
across multiple monitors
For TM-4010HDMI/4011HDMI Models with P-CAP Touchscreen
If your monitors are TM-4010HDMI/TM-4011HDMI models, you may
configure the display settings from Control Panel in Microsoft Windows to
identify the monitor as the secondary touchscreen monitor. Please go through
the below steps to complete configuration.
1. Make sure that the monitor is well connected to your POS terminal.
2. Go to Control Panel>Display Settings, change your display settings to
extended mode.
3. Go to Control Panel, and then click on
Tablet PC Settings item.
4. In Tablet PC Settings dialogue box, click
on Setup button.
9
5. Following the instruction shown on the screen, click on the screen that
you want to identify as the primary touchscreen display.
6. Press Enter button to proceed the configuration.
7. Click on the screen you want to use as the secondary touchscreen
display.
Powering ON/OFF your Monitor
To start up LM/TM-401xHDMI, please make sure that the monitor is well
connected to the POS terminal and the power is supplied to the monitor
through POS terminal.
Installing Drivers
Please visit Posiflex official website to download and install the related drivers.
http://www.posiflex.com/en-global/Download/download)
Setting up Display Resolution for Your Monitor
The below chart defines the list of recommended display settings for LM/TM-
401xHDMI. Improper display configuration will prevent the monitor from
properly displaying the image and lead to a warning message of “out of range”
prompted on the screen.
10
9.7” LM/TM-4010HDMI
Display Resolution
Horizontal Frequency (KHz)
Refresh Rate (Hz)
640 x 400
37.9
70
640 x 480
31.5
60
37.9
72
37.5
75
720 x 400
37.9
70
800 x 600
35.1
56
37.9
60
48.1
72
46.9
75
1024 x 768
48.4
60
10.1” LM/TM-4011HDMI
Display Resolution
Horizontal Frequency (KHz)
Refresh Rate (Hz)
640 x 480
31.5
60
37.9
72
37.5
75
800 x 600
37.9
60
48.1
72
46.9
75
1024 x 768
48.4
60
1280 x 720
45.0
60
1280 x 800
49.7
60
11
Specification
LM/TM-4011HDMI
LM/TM-4010HDMI
Display
LCD Panel
10.1" TFT LCD
9.7" TFT LCD
Resolution
1280(H) x 800 (V)
1024(H) x 768 (V)
Active Area
216.96mm (H) x
135.60mm (V)
196.61mm (H) x
147.46mm (V)
Pixel
Arrangement
R.G.B. Vertical Stripe
Viewing
Angle
85/85/85/85 degree
(U/D/L/R)
70/60/70/70 degree
(U/D/L/R)
Contrast Ratio
800 : 1
500 : 1
Response Time
25ms
20ms
Brightness
400 cd/m
2
350 cd/m
2
Display
Interface
VGA Port / HDMI Port
Power Supply
12V from Posiflex terminal VGA Port
12V from Posiflex terminal 12V DC-OUT Power Jack
12V from 12V/18W power adaptor
Touch
Touch type
P-CAP
N/A
P-CAP
N/A
Interface
USB
N/A
USB
N/A
I/O Ports
HDMI Port
1 Port
VGA Port
1 Port
USB Port
1 Port (Type B)
DC-Jack
12V DC-IN
※
The product information and specifications are subject to change without
prior notice. To get the detailed information on LM/TM-401XHDMI,
please check this model from Posiflex Global Website
(http://www.posiflex.com/en-global/Download/download).
12
<MEMO>
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Posiflex TM/LM-401xHDMI Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Posiflex TM/LM-401xHDMI User manual
Documents connexes
-
Posiflex TM-3112HDMI Manuel utilisateur
-
-
-
-
Posiflex RT-5115 Manuel utilisateur
-
-
Posiflex RT-6115 Manuel utilisateur
-
-
-